Is the use of digital technologies for the fabrication of implant-supported reconstructions more efficient and/or more effective than conventional techniques: A systematic review

Clinical outcome of monolithic zirconia on bonded or mechanically retained prefabricated titanium-base: A 4-year retrospective study

OBJECTIVE

To assess the clinical performance of monolithic screw-retained implant-supported zirconia crowns (MSI) bonded or mechanically retained on prefabricated Ti-bases using a complete digital workflow.

METHODS

A retrospective analysis was conducted on patients who underwent single dental implant procedures between January 2017 and May 2018. Inclusion criteria were: patients over 18 years of age; implants placed in posterior sites; MSI on prefabricated Ti-base realized by using a complete digital workflow; a minimum follow-up period of 2 years. Cemented crowns and fixed dental prosthesis were excluded. Mechanical complications included: fracture of Ti-base; loss of retention; loosening of Ti-base screws. Technical complications included: fracture and debonding of monolithic zirconia. Biological complication was set strictly at a probing pocket depth of 5 mm and bleeding on probing or pus secretion.

RESULTS

A total of 144 dental implants placed in 127 patients were included, 73 with a fully tapered implant system (BLX) and 71 with a conical connection system (Nobel Parallel CC). Of the 73 BLX implants, 4 experienced loosening of the Ti-base screw, while 3 Nobel Parallel CC implants experienced the same problem. In addition, 4 fractures of the Ti-base and 6 fractures of the inner surface of the monolithic zirconia were observed in the Nobel Parallel CC implants. Cumulative survival was 100 % for bonded crowns and 85 % for mechanically retained crowns. Radiographic evaluation revealed a mean CBL of 0.12 mm for the BLX and 0.13 mm for the Nobel Parallel CC implants with no statistically significant differences between the Ti-base types. There was no evidence of bleeding on probing or pus secretion. All probing pocket depths were <3 mm.

CONCLUSION

The use of a prefabricated Ti-base remains a clinically acceptable choice, however, MSIs bonded to prefabricated Ti-bases had fewer mechanical and technical complications than the MSI mechanically retained to a prefabricated Ti-base.

Knowledge structure and research hotspots on digital scanning for implant-supported complete-arch prosthesis: A bibliometric analysis

Background

Digital scanning is increasingly widely used for implant-supported complete-arch prosthese. However, a quantitative literature analysis is lacking for this field. This study aims to conduct a bibliometric analysis to summarize the knowledge structure and research hotspots of digital scanning for implant-supported complete-arch prosthesis.

Materials and methods

Relevant articles and reviews, published between 1994 and 2023, were obtained from the Web of Science Core Collection (WoSCC). Indicators such as publication count, annual growth, citation count, co-citation count, impact factor, Journal citation reports (JCR) division, H-index are used to assess the contribution of countries, journals, authors or the quality of articles. Visual maps, cluster analysis and keyword cloud are used to evaluate the cooperation pattern and topic trends.

Results

580 eligible publications, including 555 articles and 25 reviews, were analyzed. The United States is the leading country in this area, received the most citations. The Journal of Prosthetic Dentistry is the scientific journal with the highest impact. The analysis of keywords and ongoing trials shows that the accuracy of relevant techniques is a current hot topic in this field.

Conclusion

In recent years, digital scanning technique for implant-supported complete-arch prosthesis has made rapid progress. By reviewing the published literature, we found the United States is the global leader in the field of digital scanning for complete-arch implant prosthesis. Accuracy is the core word in this field, more scientific evidence is needed to support the clinical application of digital scanning in this field.

Material and abutment selection for CAD/CAM implant-supported fixed dental prostheses in partially edentulous patients - A narrative review

Restorative material selection has become increasingly challenging due to the speed of new developments in the field of dental material science. The present narrative review gives an overview of the current indications for implant abutments and restoration materials for provisional and definitive implant-supported fixed dental prostheses in partially edentulous patients. For single implant restorations, titanium base abutments for crowns are suggested as an alternative to the conventional stock- and customized abutments made out of metal or zirconia. They combine the mechanical stability of a metallic connection with the esthetic potential of ceramics. For multiple-unit restorations, conical titanium bases especially designed for bridges are recommended, to compensate for deviating implant insertion axes and angulations. Even though titanium base abutments with different geometries and heights are available, certain clinical scenarios still benefit from customized titanium abutments. Indications for the definitive material in fixed implant restorations depend on the region of tooth replacement. In the posterior (not esthetically critical) zone, ceramics such as zirconia (3-5-Ymol%) and lithium-disilicate are recommended to be used in a monolithic fashion. In the anterior sector, ceramic restorations may be buccally micro-veneered for an optimal esthetic appearance. Lithium-disilicate is only recommended for single-crowns, while zirconia (3-5-Ymol%) is also recommended for multiple-unit and cantilever restorations. Attention must be given to the specific mechanical properties of different types of zirconia, as some feature reduced mechanical strengths and are therefore not indicated for all regions and restoration span lengths. Metal-ceramics remain an option, especially for cantilever restorations.

Influence of different scan body design features and intraoral scanners on the congruence between scan body meshes and library files: An in vitro study

STATEMENT OF PROBLEM

Implant scan bodies (ISBs) present with a variety of features, including diverse design geometries and manufacturing materials. How these features influence the congruence between the clinically obtained mesh file and the software-based library file of the scan body during the alignment stage within the computer-aided design (CAD) software program is unclear. It is also uncertain how these features influence the scanning accuracy of different scanners.

PURPOSE

The purpose of this in vitro study was to investigate how various scan body shapes manufactured from different materials influence the scanning accuracy of 6 intraoral scanners (IOSs) and 1 desktop scanner.

MATERIAL AND METHODS

A 3-dimensionally (3D) printed cast fitted with 4 different implant analogs and their corresponding scan bodies (Straumann Cares RN Mono; Straumann, MIS V3 SP; MIS, Paltop SP; Paltop and TV70; TRI) was scanned using 6 intraoral scanners (Primescan; Dentsply Sirona, TRIOS 3; 3Shape A/S, TRIOS 5; 3Shape A/S, Medit i-700; Medit, Fussen S6000; Fussen, and Runyes 3DS; Runyes) and 1 desktop scanner (7series; Dental Wings). A metrology mesh comparison software program was used for analysis. Inferences were drawn using a univariate repeated measures 2-way ANOVA. Post hoc analysis was conducted with pairwise Bonferroni tests (α=.05).

RESULTS

A significant 2-way interaction was found between scanner model and scan body model, (F [5.518, 49.659]=36.251, P<.001). The mean absolute deviation for the different scanners ranged between 21 µm and 35 µm across all scan bodies, but the model of the scan body influenced the deviation of the scanner. The mean absolute deviation for the different scan bodies ranged from 19 µm to 46 µm across all scanners, but the model of the scanner influenced the deviation of the scan body.

CONCLUSIONS

Regarding implant scan body features, a design with a less complex shape and fewer sharp line angles and a design with a cylindrical shape exhibited statistically significantly higher congruence between the clinical mesh and the software library files. Regarding intraoral scanners, Primescan had a statistically significantly lower mean absolute deviation compared with that of the other scanners across all scan bodies tested.

Effect of Different Intraoral Scanners on the Accuracy of Bite Registration in Edentulous Maxillary and Mandibular Arches

OBJECTIVES

The objective of this study was to use in vitro models to examine the bite registration accuracy of four different intraoral scanners (IOS) for edentulous maxillary and mandibular arches. The objective was to assess the trueness and precision of the IOS and determine if there were significant differences between them.

METHODS

An Asiga Max UV 3D printer was used to print maxillary and mandibular edentulous models based on the shape of Frasaco models (artificial dental arch models). Four dental implants were placed symmetrically in both models using Straumann BLT RC implants. Digital impressions were taken with Primescan, Trios 3, Trios 4, and Medit i500 intraoral scanners (n = 10 for each IOS). Digital bite registrations were made, and scanning data was exported in STL format. The accuracy of the interarch distance (the distance between the metrological spheres attached to the mandibular and maxillary models) was estimated for each IOS.

RESULTS

The results showed significant differences in trueness and precision between different IOS (p <.05), except Medit i500 and Trios 3 (p >.05). Primescan provided the most accurate results, followed by Medit i500, Trios 3, and Trios 4, respectively.

CONCLUSIONS

within the limitations of this study, the IOS type affects the accuracy of interocclusal bite registration in in vitro design. Only Primescan achieved clinically acceptable accuracy for the interocclusal recording of edentulous arches.

CLINICAL RELEVANCE

The comparison of the accuracy of bite registration between different intraoral scanners will help increase the efficiency of the clinical application of digitalized interarch registration.

Clinical performance and risk factors of all-ceramic screw-retained implant crowns in the posterior region based on a retrospective investigation

OBJECTIVES

Clinical data on all-ceramic screw-retained implant crowns (SICs) luted on titanium base abutments (TBAs) over more than 3 years are sparse. This study aimed to evaluate the clinical performance and potential risk factors for these restorations.

MATERIALS AND METHODS

Analysis took place based on the medical patient-records of three dental offices. Implant survival and prosthetic complications over time were evaluated. The study included SICs in premolar and molar regions made from monolithic lithium disilicate ceramic (M_LiDi) or veneered zirconia (V_ZiO) luted on a TBA documented over an observation time of at least 3 years. Survival and complication rates were calculated and compared by a log-rank test. Cox-Regressions were used to check potential predictors for the survival (p < .05).

RESULTS

Six hundred and one crowns out of 371 patients met the inclusion criteria and follow-up period was between 3.0 and 12.9 (mean: 6.4 (SD: 2.1)) years. Over time, six implants had to be removed and 16 restorations had to be refabricated. The estimated survival rates over 10 years were 93.5% for M_LiDi and 95.9% for V_ZiO and did not differ significantly among each other (p = .80). However, V_ZiO showed significantly higher complication rates (p = .003). Material selection, sex, age, and implant diameter did not affect the survival of investigated SICs but crown height influences significantly the survival rate (hazard ratio, HR = 1.26 (95%CI: 1.08, 1.49); p = .043).

CONCLUSIONS

Screw-retained SICs luted on TBAs that were fabricated from monolithic lithium disilicate ceramic or veneered zirconia showed reliable and similar survival rates. Increasing crown heights reduced survival over the years.

In Vitro Comparative Analysis of Digital Versus Conventional Impressions in Fixed Prosthodontics

Background

In the realm of fixed prosthodontics, the transition from conventional to digital impressions has been a subject of ongoing debate. This study aims to provide a comparative analysis of digital versus conventional impressions in terms of accuracy and efficiency.

Materials and Methods

Twenty patients requiring fixed prosthodontic treatment were selected for this study. Each patient received both digital and conventional impressions. The digital impressions were obtained using an intraoral scanner, while conventional impressions were taken using polyvinyl siloxane material. The impressions were then used to fabricate fixed prostheses for each patient. Accuracy was assessed through measurement of marginal fit using a standardized technique, and efficiency was evaluated based on time taken for impression procedures.

Results

The mean marginal discrepancy for digital impressions was found to be 38 micrometers (±5), whereas for conventional impressions, it was 45 micrometers (±7). Additionally, the average time taken for digital impressions was 12 minutes, compared to 20 minutes for conventional impressions.

Conclusion

Digital impressions demonstrated superior accuracy and efficiency compared to conventional impressions in fixed prosthodontics.

Immediate loading of definitive restorations in partially edentulous patients requiring an implant-supported prosthesis: A scoping review

STATEMENT OF PROBLEM

Interest is growing in immediately loading definitive implant-supported prostheses. However, it appears that implant protocols are evolving faster than their scientific validation.

PURPOSE

The purpose of this scoping review was to identify the current trends, feasibility, and clinical outcomes of a specific clinical loading scenario (type A), where a single definitive implant-retained restoration is delivered within 3 days. The focus question was "In partially edentulous patients requiring an implant-retained prosthesis (population), is immediate loading with a definitive restoration (concept) a viable treatment option (context)?"

MATERIAL AND METHODS

An electronic search was conducted in the PubMed, CENTRAL, Scopus, Embase, and Web of Science databases. Two authors independently reviewed the studies, screened titles and abstracts, and performed full-text analysis. Cross-reference checks within the bibliography of included studies, relevant reviews, and guideline were conducted. Bibliometric information and study details were extracted.

RESULTS

The search identified 2568 titles after removing duplicates. Four studies involving 91 participant and 100 implant-retained restorations were included in this scoping review. The selected articles were a randomized controlled trial (RCT), a prospective clinical study, and the remaining 2 were case series. The follow-up periods investigated ranged from 6 to 26 months. All studies evaluated marginal bone loss as a primary outcome, and only 1 implant failure was reported. Patient-reported outcome measures were favorable, and no major biological or technical complications were reported in any study.

CONCLUSIONS

Immediate loading with a definitive restoration within 3 days appears to be a suitable approach in specific clinical situations.

A randomized clinical trial comparing the clinical fit and chairside adjustment time for implant-supported crowns fabricated by fully digital and partially digital techniques

STATEMENT OF PROBLEM

Implant-supported crowns made in both fully and partially digital workflows have been evaluated, but these studies have been mainly performed in vitro. Moreover, data on the comparison of clinical fitting and adjustment time for implant-supported crowns are limited.

PURPOSE

The purpose of this randomized clinical trial was to evaluate the clinical fit and adjustment time for implant-supported crowns produced by a partially and fully digital workflow in partially edentulous participants.

MATERIAL AND METHODS

Twenty-eight participants who had received 2 adjacent implants in posterior sites were enrolled, each receiving 2 custom titanium abutments and a splinted monolithic zirconia restoration. Restorations of the control group (n=14) were produced from a digital scan and a cast-free digital workflow, while the restorations of the test group (n=14) were from a conventional impression and a partially digital workflow. A blinded investigator delivered the restorations. The clinical adjustment was performed incrementally, and a digital chronometer recorded the time required for the evaluation and adjustment at each step. An independent t test, Mann-Whitney U test, and the Fisher exact test were used to evaluate the results (α=.05).

RESULTS

The total mean adjustment time in the control group (12.49 minutes) was significantly longer than that of the test group (11.27 minutes) (P<.001). For the occlusal contact points, significantly less clinical adjustment time was required with the cast-free digital workflow (5.31 minutes) than with the model-based partially digital workflow (6.06 minutes) (P=.001). On other surfaces, no significant difference was found between the 2 groups (P>.05). All crowns could be successfully delivered after 2 clinical appointments (impression and delivery). Remakes were not necessary for any restorations in the test or control group.

CONCLUSIONS

The parameters of occlusal adjustment time and total adjustment time of the fully digital workflow were significantly shorter than those of the partially digital workflow.

Management of an Implant-Supported Fixed Partial Denture in the Esthetic Zone in a Patient With a Very Limited Mouth Opening: A Case Report

In the maxillary anterior area, the esthetic integration of prosthetic restorations is a challenge, particularly for screw-retained implant prostheses. This case report presents the management and clinical outcome of an old partial edentulous maxillary jaw in an esthetic zone in a young patient with a very limited mouth opening. This patient was rehabilitated with an implant screw-retained fixed partial denture (FPD) using both digital and conventional techniques.

Impact of profile angle of CAD-CAM abutment on the marginal bone loss of implant-supported single-tooth posterior restorations

STATEMENT OF PROBLEM

Although the emergence angle has been related to marginal bone loss, information regarding the relationship between the transmucosal configuration of a computer-aided design and computer-aided manufacturing (CAD-CAM) abutment at specific subgingival levels and the amount of marginal bone loss is lacking.

PURPOSE

The purpose of this retrospective clinical study was to evaluate the influence of CAD-CAM abutment profile angles, measured at different subgingival positions, on the marginal bone loss of posterior single-tooth implant-supported restorations.

MATERIAL AND METHODS

A total of 260 posterior single-tooth implant-supported restorations using CAD-CAM abutments were analyzed in 206 patients. All implants had internal conical seal connections with a platform-switched design. The following data were extracted using digital periapical radiography: emergence profile, profile angle at distance ranges of 0 to 1 mm, 1 to 2 mm, and 2 to 3 mm from the implant-abutment junction, and peri-implant marginal bone loss (MBL). The MBL was measured from the time of delivery of the restorations up to 7 years or more. A linear mixed model was applied to investigate whether there was a significant difference in MBL based on the emergence profile and time, followed by the Bonferroni correction post hoc test. A Pearson correlation analysis was used to analyze the correlation between the profile angle and MBL at each distance range. The cut-off points for each distance range were determined by using the c-index, and independent t tests were conducted based on these cut-off values to evaluate the statistical differences (α=.05 for all statistical analyses).

RESULTS

The convex emergence profile exhibited greater MBL than the concave and straight profiles at each follow-up visit (P<.001). A significant correlation was found between the profile angle and MBL in the 0 to 1 mm, 1 to 2 mm distance ranges. However, no significant correlation was found between the profile angle and MBL in the 2 to 3 mm distance range (P>.05). The cut-off points were 34 degrees at the mesial and 28 degrees at the distal in the 0 to 1 mm range, and 33 and 20 degrees at the mesial and distal in the 1 to 2 mm range.

CONCLUSIONS

The profile angle near the implant-abutment junction and the type of emergence profile of the CAD-CAM abutment were closely associated with MBL in implants with internal conical seal connection with a platform switch design.

A double-blind randomized within-subject study to evaluate clinical applicability of four digital workflows for the fabrication of posterior single implant crown

OBJECTIVE

To compare efficiency and clinical efficacy of posterior single implant crowns (PSIC) fabricated using four digital workflows.

MATERIALS AND METHODS

Twenty-two patients with one missing first molar were included. Each patient received four screw-retained implant crowns fabricated through four different workflows including a fully digital workflow with immediate digital impression (Group i-IOS), a fully digital workflow with digital impression after implant osseointegration (Group d-IOS), a model-based hybrid workflow using immediate analogue impression (Group i-AI), and a model-based hybrid workflow with conventional analogue impression after implant osseointegration (Group d-AI). The crown delivery sequence was randomized and blinded. The efficiency for each workflow and clinical outcome of each crown were recorded.

RESULTS

The average clinical working time in fully digital workflows (i-IOS 46.90 min, d-IOS 45.66 min) was significantly lower than that in the hybrid workflows (i-AI 54.59 min, d-AI 55.96 min; p < .001). Significantly more laboratory time was spent in hybrid workflows (i-AI 839.60 min, d-AI 811.73 min) as compared to fully digital workflows (i-IOS 606.25 min, d-IOS 607.83 min, p < .01). No significant differences in the chairside time at delivery were found. More crowns in Group i-AI (15%) needed additional laboratory interventions than in the other groups (p = .029).

CONCLUSION

Digital impression and model-free fully digital workflow improved prosthetic efficiency in the fabrication of PSIC. With the limitation that the results were only applicable to the implant system used and the digital technologies applied, findings suggested that workflows integrating immediate impression with implant surgery procedure was clinically applicable for restoration of PSIC.

Full-arch restoration with the NEXUS IOS® system: A retrospective clinical evaluation of 37 restorations after a one year of follow-up

OBJECTIVES

Report the results with a novel workflow of digital restoration for completely edentulous patients with implant supported full arch fixed dental prostheses (ISFDP).

METHODS

This multicenter retrospective clinical study was based on the evaluation from a cohort of 29 patients restored with 37 ISFDP designed and manufactured from the data captured by a direct intraoral scan, using a novel full digital system (NEXUS IOS®, Osteon Medical, a Keystone Dental Group company, Melbourne, Australia). Data was collected over a 3-year period, in six different dental centers. This study reported on the clinical parameters including: precision of marginal fit, functional and aesthetic integration of Nexus ISFDP. All patients were followed for a period of one year post delivery. Implant survival, biologic and prosthetic complications were assessed, at one year. A statistical analysis was conducted.

RESULTS

All 37 ISFDP were deemed clinically acceptable on insertion. Implant survival at one year was 100 %. The biologic and prosthetic complications were minimal during the follow-up period.

CONCLUSIONS

ISFDP, designed and manufactured using the NEXUS IOS® system, are clinically acceptable, with a low incidence of complications at one year. Long-term clinical studies are needed.

STATEMENT OF CLINICAL RELEVANCE

Within the limitations of this study (retrospective design, small patient sample, limited follow-up) the NEXUS IOS® system seems to represent a viable solution for the restoration of completely edentulous patients with ISFDP, in a full digital workflow.

Clinical evaluation and quantitative occlusal change analysis of posterior implant-supported all-ceramic crowns: A 3-year randomized controlled clinical trial

OBJECTIVES

To compare the survival and complication rates of posterior screw-retained monolithic lithium disilicate (LS2 )/veneered zirconia (ZrO2 ) single implant crowns (SICs), as well as analyze the occlusal changes observed during a 3-year follow-up period.

MATERIALS AND METHODS

Thirty-three patients were included and randomly divided into two groups. The test group consisted of 17 patients who received monolithic-LS2 -SIC, while the control group consisted of 16 patients who received veneered-ZrO2 -SIC. Implant/prosthesis survival rates, technical complications, peri-implant soft tissue conditions, and quantitative occlusal changes of SIC (obtained by the intra-oral scanner and analyzed in reverse software Geomagic Control 2015) were assessed at 1- and 3-year follow-ups. Bone loss and Functional Implant Prosthodontic Score (FIPS) were evaluated at a 3-year follow-up.

RESULTS

After a 3-year follow-up period, one patient dropped out of the follow-up. No implant loss was observed. One crown was fractured, resulting in prosthesis survival rates of 93.75% for the monolithic group and 100% for the veneered group. A technical complication rate of 25% (4/16) was observed in the veneered group (p = .333). No significant differences in the marginal bone loss were observed at the 3-year follow-up (0.00 (-0.22, 0.17) mm versus 0.00 (-0.12, 0.12) mm, p = .956). The total FIPS scores for the test group were 9.0 (9.0, 9.0), while the control group received scores of 9.0 (8.0, 10.0) (p = .953). The changes in mean occlusal clearance were 0.022 ± 0.083 mm for the test and 0.034 ± 0.077 mm for the control group (at 3 years, p = .497). The changes in occlusal contact area were 1.075 ± 2.575 mm2 for the test and 1.676 ± 2.551 mm2 for the control group (at 3 years, p = .873).

CONCLUSION

After a 3-year follow-up, screw-retained monolithic LS2 and veneered ZrO2 SIC demonstrated similar survival rates. The occlusal performance of implant prostheses needs to be closely examined during follow-up, and appropriate occlusal adjustments need to be considered.

Clinical outcomes of digital scans versus conventional impressions for implant-supported fixed complete arch prostheses: A systematic review and meta-analysis

STATEMENT OF PROBLEM

With the growing use of digital scanning, an evaluation of the clinical impact of digital scans versus conventional impressions in complete arch implant-supported prostheses is needed. However, systematic reviews on this subject are lacking.

PURPOSE

The purpose of this systematic review was to evaluate the scanning and impression times and the radiographic marginal bone loss over time associated with digital scans and conventional impressions for complete arch implant-supported fixed prostheses.

MATERIAL AND METHODS

The search was performed in MEDLINE/PubMed, SCOPUS, EMBASE, and Web of Science. Only randomized clinical trials (RCTs) comparing digital scans and conventional impressions for complete arch prostheses were included in the review. The scan and impression times and marginal bone loss were analyzed through random effects meta-analysis.

RESULTS

Six RCTs were included. The meta-analysis was conducted by using a standardized mean difference (MD) and indicated a statistically significant reduction in time for the digital scan group compared with the conventional group (MD 10.01 [7.46, 12.55], P<.001, I²=80%). The fact that digital scans were used did not lead to significant differences in radiographic marginal bone loss compared with conventional impressions after 6 months (MD -0.03 [-0.14, 0.08], P=.58, I²=0%), after 12 months (MD -0.06 [-0.24, 0.12], P=.12, I²=45%), and after 24 months (MD -0.12 [-0.32, 0.09], P=.28, I²=58%).

CONCLUSIONS

Digital scans significantly reduced the time required compared with conventional impressions for complete arch implant-supported prostheses. Nevertheless, additional studies with more consistent methodologies are needed for confirmation. No significant differences were found in radiographic marginal bone loss between treatments performed with digital scans and conventional impressions.

Digital mounting accuracy of 2 intraoral scanners with a single anterior or bilateral posterior occlusal scan: A three-dimensional analysis

STATEMENT OF PROBLEM

Although intraoral scanners (IOSs) are popular, few studies have evaluated the accuracy of digital mounting by using IOSs.

PURPOSE

The purpose of this in vitro study was to compare the accuracy of digital mounting by using 2 IOSs and 2 occlusal scanning methods.

MATERIAL AND METHODS

Fourteen Ø5-mm zirconia balls were attached approximately 5 mm apical to the free gingival margin of both second molars, second premolars, and canines and between the central incisors in maxillary and mandibular epoxy casts. A polyetheretherketone hexagonal cube with a 10-mm-long edge was attached to the buccal side of the missing mandibular right first molar area, and the cube was used to set a part coordinate system. Two IOSs (TRIOS 3, Primescan) were used to assess the intra-arch and interarch accuracies. For intra-arch assessment, each IOS was used to digitally scan the mandibular epoxy cast 15 times and fabricate 15 datasets. The deviation of each zirconia ball centroid was statistically compared between the IOSs. For interarch assessment, each IOS was used to digitally scan the maxillary and mandibular epoxy casts, and the data were digitally mounted by using a single anterior occlusal scan (A) or bilateral posterior occlusal scan (P). Both occlusal scans were performed 15 times; therefore, 4 groups (15 datasets per group) of mounted digital datasets were assigned. The deviation of each maxillary zirconia ball centroid, as well as the interarch distance between the corresponding maxillary and mandibular zirconia ball centroids, were compared among the 4 groups. For statistical analysis, the Mann-Whitney U test and Kruskal-Wallis test with Bonferroni correction were used (α=.05).

RESULTS

Primescan had less deviation than TRIOS 3 in the complete arch scan. When the zirconia balls were close to the origin, the bilateral posterior occlusal scan produced less deviation of their centroids. Primescan produced decreased interarch distance in the anterior and posterior dentition, while TRIOS 3 produced increased interarch distance in the anterior dentition and decreased interarch distance in the posterior dentition.

CONCLUSIONS

A significant difference was noted in intra-arch accuracy between the IOSs, and the difference influenced the digital mounting accuracy. The type of occlusal scan and IOS significantly influenced the accuracy of digital mounting. Both IOSs produced decreased interarch distances in the second molar area.

Systematic review evaluating the influence of the prosthetic material and prosthetic design on the clinical outcomes of implant-supported multi-unit fixed dental prosthesis in the posterior area

OBJECTIVE

The objectives of the study were to assess the survival, failure, and technical complication rates of implant-supported fixed dental prosthesis (iFDPs) with pontic or splinted crown (iSp C) designs in the posterior area and compare the influence of prosthetic materials and prosthetic design on the outcomes.

METHODS

Electronic and manual searches were performed to identify randomized-, prospective-, and retrospective clinical trials with follow-up time of ≥12 months, evaluating the clinical outcomes of posterior iFDPs with pontic or iSp Cs. Survival and complication rates were analyzed using robust Poisson's regression models.

RESULTS

Thirty-two studies reporting on 42 study arms were included in the present systematic review. The meta-analysis of the included studies indicated estimated 3-year survival rates of 98.3% (95%CI: 95.6-99.3%) for porcelain-fused-to-metal (PFM) iFDPs, 97.5% (95%CI: 95.5-98.7%) for veneered zirconia (Zr) iFDPs with pontic, 98.9% (95%CI: 96.8-99.6%) for monolithic or micro-veneered zirconia iFDPs with pontic, and 97.0% (95%CI: 84.8-99.9%) for lithium disilicate iFDPs with pontics. The survival rates for different material combination showed no statistically significant differences. Veneered restorations, overall, showed significantly (p < .01) higher ceramic fracture and chipping rates compared with monolithic restorations. Furthermore, there was no significant difference in survival rates (98.3% [95%CI: 95.6-99.3%] vs. 99.1% [95%CI: 97.6-99.7%]) and overall complication rates between PFM iFDPs with pontic and PFM iSp Cs.

CONCLUSIONS

Based on the data identified by this systematic review, PFM, veneered Zr, and monolithic Zr iFDPs with pontic and iSp Cs showed similarly high short-term survival rates in the posterior area. Veneered restorations exhibit ceramic chipping more often than monolithic restorations, with the highest fracture rate reported for veneered Zr iFDPs.

Additively and subtractively manufactured implant-supported fixed dental prostheses: A systematic review

AIM

To compare and report on the performance of implant-supported fixed dental prostheses (iFDPs) fabricated using additive (AM) or subtractive (SM) manufacturing.

METHODS

An electronic search was conducted (Medline, Embase, Cochrane Central, Epistemonikos, clinical trials registries) with a focused PICO question: In partially edentulous patients with missing single (or multiple) teeth undergoing dental implant therapy (P), do AM iFDPs (I) compared to SM iFDPs (C) result in improved clinical performance (O)? Included were studies comparing AM to SM iFDPs (randomized clinical trials, prospective/retrospective clinical studies, case series, in vitro studies).

RESULTS

Of 2'184 citations, no clinical study met the inclusion criteria, whereas six in vitro studies proved to be eligible. Due to the lack of clinical studies and considerable heterogeneity across the studies, no meta-analysis could be performed. AM iFDPs were made of zirconia and polymers. For SM iFDPs, zirconia, lithium disilicate, resin-modified ceramics and different types of polymer-based materials were used. Performance was evaluated by assessing marginal and internal discrepancies and mechanical properties (fracture loads, bending moments). Three of the included studies examined the marginal and internal discrepancies of interim or definitive iFDPs, while four examined mechanical properties. Based on marginal and internal discrepancies as well as the mechanical properties of AM and SM iFDPs, the studies revealed inconclusive results.

CONCLUSION

Despite the development of AM and the comprehensive search, there is very limited data available on the performance of AM iFDPs and their comparison to SM techniques. Therefore, the clinical performance of iFDPs by AM remains to be elucidated.

Conventional and Digital Impressions for Fabrication of Complete Implant-Supported Bars: A Comparative In Vitro Study

Obtaining accurate models and well-fitting prostheses during the fabrication of complete implant-supported prostheses has been a significant challenge. Conventional impression methods involve multiple clinical and laboratory steps that can lead to distortions, potentially resulting in inaccurate prostheses. In contrast, digital impressions may eliminate some of these steps, leading to better-fitting prostheses. Therefore, it is important to compare conventional and digital impressions for producing implant-supported prostheses. This study aimed to compare the quality of digital intraoral and conventional impressions by measuring the vertical misfit of implant-supported complete bars obtained using both types of techniques. Five digital impressions using an intraoral scanner and five impressions using elastomer were made in a four-implant master model. The plaster models produced with conventional impressions were scanned in a laboratory scanner to obtain virtual models. Screw-retained bars (n = five) were designed on the models and milled in zirconia. The bars fabricated using digital (DI) and conventional (CI) impressions were screwed to the master model, initially with one screw (DI1 and CI1) and later with four screws (DI4 and CI4), and were analyzed under a SEM to measure the misfit. ANOVA was used to compare the results (p < 0.05). There were no statistically significant differences in the misfit between the bars fabricated using digital and conventional impressions when screwed with one (DI1 = 94.45 µm vs. CI1 = 101.90 µm: F = 0.096; p = 0.761) or four screws (DI4 = 59.43 µm vs. CI4 = 75.62 µm: F = 2.655; p = 0.139). Further, there were no differences when the bars were compared within the same group screwed with one or four screws (DI1 = 94.45 µm vs. DI4 = 59.43 µm: F = 2.926; p = 0.123; CI1 = 101.90 µm vs. CI4 = 75.62 µm: F = 0.013; p = 0.907). It was concluded that both impression techniques produced bars with a satisfactory fit, regardless of whether they were screwed with one or four screws.

Atraumatic intraoral scans and virtual hybrid casts for custom implant abutments and zirconia implants: Accuracy of the workflow

STATEMENT OF PROBLEM

Making impressions of 2-piece implants is typically associated with the repeated disassembly and reassembly of superstructures and related to soft-tissue trauma. Intraoral scanning of 1-piece zirconia implants is problematic because scan bodies are not readily available. Whether using virtual hybrid casts generated by merging intraoral scan data with the known surface geometry of abutments can solve these difficulties is not clear because data on accuracy of the workflow are sparse.

PURPOSE

The purpose of this in vitro study was to evaluate the accuracy of virtual hybrid casts with respect to the impact of different gingival situations. The workflow was designed to render pointless the use of impression posts and scan bodies and avoid any displacement of the gingiva.

MATERIAL AND METHODS

The mandibular right first molar in a typodont was replaced with a 2-piece titanium implant with a custom abutment and then a 1-piece zirconia implant. Three situations representing different gingival heights covering the abutments were simulated. Twelve intraoral scans were made for each situation to capture the recordable parts of the abutments, and virtual hybrid casts were constructed by superimposing and merging the intraoral scan data with the original laboratory scan data of the abutments. Hybrid casts were compared with reference data by using the root mean square error. Scan body-related and cast scan-related protocols were performed representing conventional digital workflows. Statistical analysis with the Kolmogorov-Smirnov, Kruskal-Wallis, and Mann-Whitney U tests with the Bonferroni correction was conducted with a statistical software program (α=.05).

RESULTS

Deviation was low in the hybrid casts of the custom abutment when the entire abutment was recorded (6.5 μm; IQR: 3.0 μm), when the preparation margin was disguised (7.0 μm; IQR: 1.0 μm), and when half of the abutment was covered (8.0 μm; IQR: 4.0 μm). The accuracy in the 1-piece zirconia implant was 10.0 μm (IQR: 4.0 μm) when the whole surface of the abutment was visible and 12.5 μm (IQR: 6.0 μm) when the preparation margin was covered. When only half of the abutment was captured, a larger deviation of 22.0 μm (IQR: 7.0 μm) was observed. The hybrid cast concept demonstrated superior accuracy compared with protocols using scan bodies (76.0 μm; IQR: 27.0 μm) and cast scans (23.0 μm; IQR: 15.0 μm).

CONCLUSIONS

Digital intraoral scanning and the generation of virtual hybrid casts provide high accuracy and are suitable for the fabrication of single-implant-supported restorations. The atraumatic procedure avoids tissue manipulation and reduces clinical effort.

Randomized controlled pilot study assessing efficacy, efficiency, and patient-reported outcomes measures of chairside and labside single-tooth restorations

OBJECTIVES

To test whether or not a chairside workflow (CHAIR) is similar to a labside workflow (LAB) in terms of efficacy (primary outcome) and efficiency (secondary outcome).

MATERIAL AND METHODS

Eighteen subjects in need of a single-tooth restoration in the posterior region of the maxilla or mandible were consecutively recruited and randomly assigned to the CHAIR or LAB workflow. Patient-reported outcome measures (PROMs; efficacy) were assessed using a questionnaire with visual analog scale. The white AEsthetic score (WES) was applied to evaluate the AEsthetic outcome objectively. The clinical and laboratory time (efficiency) were recorded. Nonparametric methods were applied for the group comparisons.

RESULTS

The overall median AEsthetic evaluation after treatment was 10 (interquartile range = IQR: 9.5-10) in group CHAIR and 10 (IQR: 9.5-10) in-group LAB (Mann-Whitney [MW] test p = 1.000). The WES amounted to 4 (IQR: 3-5) (CHAIR) and to 8 (IQR: 7-9) (LAB) (MW test p < 0.0001). The median total working time for the clinician in-group CHAIR was 49.9 min. (IQR: 40.9-63.7) and 41.4 min. (IQR: 37.2-58.2) in-group LAB (MW test p = 0.387).

CONCLUSIONS

Subjective PROMs of single-tooth supported restorations fabricated in a CHAIR or LAB workflow led to similar scores of patients' satisfaction and a moderate negative correlation for the objective evaluation of the clinician in the LAB workflow.

CLINICAL SIGNIFICANCE

PROMs can be considered a key element in the decision-making process for restoring single-tooth restorations. The patients' perception of AEsthetics was similar for the CHAIR or LAB workflows. The additional efforts undertaken with the LAB workflow did not result in a patient benefit when compared to a CHAIR workflow.

A completely digital workflow aided by cone beam computed tomography scanning to maintain jaw relationships for implant-supported fixed complete dentures: A clinical study

STATEMENT OF PROBLEM

The conventional workflow for the fabrication of implant-supported fixed complete dentures (IFCDs) is complex and makes it impossible to maintain jaw relationships. A fully digital workflow might solve this problem.

PURPOSE

The purpose of this clinical study was to develop a completely digital workflow aided by a cone beam computed tomography (CBCT) scan for the fabrication of IFCDs and to evaluate the accuracy of this workflow with regard to the maintenance of jaw relationships.

MATERIAL AND METHODS

All participants received a preoperative CBCT scan while wearing radiographic diagnosis dentures and occluding in the maximum intercuspal position. After the implant surgery, CBCT scanning, intraoral scanning, and stereophotogrammetry were performed to identify jaw anatomy, soft tissue, and the 3-dimensional (3D) locations of the implants, respectively. Then, all data were merged to transfer jaw relationships and generate digital casts to fabricate interim prostheses. A posttreatment CBCT scan was performed while the participants were wearing the interim prostheses and occluding in the maximum intercuspal position. The preoperative and postoperative jaw relationships were compared by CBCT cephalometric analysis. A meaningful and unacceptable difference was defined as 0.8 degrees and 2.4 degrees, respectively.

RESULTS

Six participants (6 jaw relationships, 9 arches, and 58 implants) were included. All interim prostheses were stable and achieved symmetric occlusion after only minimal adjustment. A total of 18 angles were measured. Three angles revealed a meaningful minimal difference, and 1 angle revealed an unacceptable minimal difference. No prosthodontic complications were reported during the study.

CONCLUSIONS

A completely digital workflow for fabricating IFCDs achieved sufficient accuracy for the maintenance of jaw relationships throughout the treatment.

Occlusal adjustment of 3-unit tooth-supported fixed dental prostheses fabricated with complete-digital and -analog workflows: A crossover clinical trial

AIM

This prospective crossover clinical trial aimed to compare the complete-digital and -analog workflows in terms of occlusal adjustment of 3-unit tooth-supported fixed dental prostheses, operator, and patient preferences.

MATERIALS AND METHOD

This study included twelve patients receiving fourteen 3-unit posterior FDPs. 2 FDPs were made for each restoration site: one fabricated in complete-digital workflow comprising intraoral scan with static bite registration (Trios 3) and a monolithic zirconia FDP (test); the other fabricated in complete-analog workflow comprising conventional impression/face-bow transfer and a porcelain-fused-to-metal FDP (control). The FDPs (n=28) were intraorally/provisionally fixed, and quadrant-like intraoral scans were taken for every FDP before & after their occlusal adjustments. Pre- and post-adjustment scans of each FDP were then superimposed using best-fit alignment (GOM Inspect) to measure the volumetric occlusal adjustment amount (mm³) (3Matic) (Mann Whitney U, α=0.05). The patient and operator experience for digital and analog workflows were evaluated using visual analog scales (Wilcoxon test, α=0.05).

RESULTS

Mean occlusal adjustments were 7.63 mm³ [±7.02] and 25.95 mm³ [±39.61] for test and control groups, respectively. The volumetric adjustment difference was clinically noticeable but not significant (P=0.12). The impression and digital workflow adjustment were perceived more favorably by both operator (P=0.003, P=0.046, respectively) and the patients (P=0.003, P=0.002, respectively).

CONCLUSIONS

Within the limitations of this clinical study, the complete digital workflow with digital static bite-registration provided high occlusal accuracy for short-span tooth-supported FDPs. In addition, the patient and operator preferences significantly favored the digital workflow.

CLINICAL SIGNIFICANCE

Complete-digital workflow employing intraoral scanning and model-free fabrication of monolithic-Zr short-span tooth-supported FDPs offers an effective treatment modality with sufficient occlusal accuracy. Therefore complete-digital workflow is a valid alternative for complete-analog workflow comprising conventional impression, face-bow transfer, and use of a semi-adjustable articulator.

Indirect restorative systems-A narrative review

OBJECTIVE

The background and clinical understanding of the properties of currently available indirect restorative systems and fabrication methods is, along with manufacturer and evidence-based literature, an important starting point to guide the clinical selection of materials for tooth and/or implant supported reconstructions. Therefore, this review explores most indirect restorative systems available in the market, especially all-ceramic, along with aspects of manufacturing process, clinical survival rates, and esthetic outcomes.

OVERVIEW

Progressive incorporation of new technologies in the dental field and advancements in materials science have enabled the development/improvement of indirect restorative systems and treatment concepts in oral rehabilitation, resulting in reliable and predictable workflows and successful esthetic and functional outcomes. Indirect restorative systems have evolved from metal ceramics and polymers to glass ceramics, polycrystalline ceramics, and resin-matrix ceramics, aiming to improve not only biological and mechanical properties, but especially the optical properties and esthetic quality of the reconstructions, in attempt to mimic natural teeth.

CONCLUSIONS

Based on several clinical research, materials, and patient-related parameters, a decision tree for the selection of indirect restorative materials was suggested to guide clinicians in the rehabilitation process.

CLINICAL SIGNIFICANCE

The pace of materials development is faster than that of clinical research aimed to support their use. Since no single material provides an ideal solution to every case, professionals must continuously seek information from well designed, long-term clinical trials in order to incorporate or not new materials and technological advancements.

Survival and prosthetic complications of monolithic ceramic implant-supported single crowns and fixed partial dentures: A systematic review with meta-analysis

STATEMENT OF PROBLEM

Monolithic ceramic implant-supported restorations have been used to rehabilitate partially edentulous patients. However, knowledge of the survival and prosthetic complications of single crowns (SCs) and fixed partial dentures (FPDs) is limited.

PURPOSE

The purpose of this systematic review with meta-analysis was to evaluate the clinical performance of monolithic ceramic implant-supported SCs and FPDs in terms of survival and prosthetic complication rates.

MATERIAL AND METHODS

The systematic review was registered on the prospective register of systematic reviews (PROSPERO) (CRD42017078568). Five electronic databases were independently searched by 2 authors for articles published until May 2022. In addition, a hand search was performed in the nonpeer-reviewed literature, specific journals, and reference lists of included articles. A single-arm meta-analysis was performed by using the R program. The risk of bias and quality were assessed using the Cochrane risk of bias tools and the Newcastle-Ottawa scale.

RESULTS

Twenty-eight studies were included in the quantitative synthesis. A total of 1298 monolithic ceramic implant-supported restorations (1116 SCs and 182 FPDs) were evaluated in 1193 participants, with a median observation time of 24 months (range: 12 to 72 months). Meta-analysis indicated the proportion of failures and prosthetic complication rates of 2% (95% confidence interval [CI]: 1% to 4%) for SCs. No difference was observed for monolithic zirconia and lithium disilicate SCs. In the FPDs, only monolithic zirconia was considered, with 1 failure reported totaling the proportion of failures of 0% (0% to 1%) and complication rates of 4% (0% to 12%). The most complications reported for both types of restorations were screw loosening, debonding, and minor chipping and were considered repairable. The included studies showed a low risk of bias and good quality.

CONCLUSIONS

The use of monolithic ceramic implant-supported SCs, independent of ceramic material, and monolithic zirconia implant-supported FPDs should be considered an effective and safe treatment option because of favorable short-term survival and low prosthetic complications. However, additional well-conducted studies with a longer-term follow-up and direct comparison between veneered restorations are recommended to reassess clinical performance.

Time efficiency and efficacy of a centralized computer-aided-design/computer-aided-manufacturing workflow for implant crown fabrication: A prospective controlled clinical study

OBJECTIVE

To assess time efficiency and the efficacy of the prosthetic manufacturing for implant crown fabrication in a centralized workflow applying computer aided design and computer aided manufacturing (CAD-CAM).

MATERIAL AND METHODS

Fifty-nine patients with one posterior implant each, were randomly allocated to either a centralized digital workflow (c-DW, test) or a laboratory digital workflow (l-DW, control). Patients were excluded from efficiency and efficacy analyses, if any additional restoration than this single implant crown had to be fabricated. A customized titanium abutment and a monolithic zirconia crown were fabricated in the c-DW. In the l-DW, models were digitalized for CAD-CAM fabrication of a monolithic zirconia crown using a standardized titanium base abutment. Time for impression, laboratory operating and delivery time were recorded. The efficacy of the prosthetic manufacturing was evaluated at try-in and at delivery. Data was analyzed descriptively. Statistical analyses using student's unpaired t- and paired Wilcoxon were performed (p < 0.05).

RESULTS

At impression taking, 12 patients (c-DW) and 19 patients (l-DW) were included. The impression time was 9.4±3.5 min (c-DW) and 15.1 ± 4.6 min (l-DW) (p < 0.05). The laboratory operating time was 130 ± 31 min (c-DW) and 218.0±8 min (l-DW) (p < 0.05). The delivery time was significantly longer in the c-DW (5.9 ± 3.5 1 days) as compared to the l-DW (0.5±0.05 days). At try-in and at delivery, efficacy of prosthetic manufacturing was similar high in both workflows.

CLINICAL RELEVANCE

The c-DW was more time efficient compared to the lab-DW and rendered a similar efficacy of prosthetic manufacturing.

Scanning Electron Microscopy Analyses of Dental Implant Abutments Debonded from Monolithic Zirconia Restorations Using Heat Treatment: An In Vitro Study

Aim: The aim of this in vitro study is to present a debonding protocol developed to remove a screw-retained, monolithic, zirconia restoration from its titanium-base abutment, and to microscopically evaluate the abutment integrity at both the prosthetic and connection levels. Materials and Methods: A total of 30 samples were tested. Each sample consisted of a monolithic zirconia restoration bonded on a titanium link abutment. Five different shapes were designed and fabricated. Randomly, one-third of the Ti-link abutments were subjected to an anodizing process. Then, all the zirconia samples were bonded to the Ti-link abutments according to a pre-established protocol. Forty-eight hours later, the samples were debonded according to the experimental protocol. The outcomes were evaluated by a visual inspection with an optical microscope, scanning electron microscopy (SEM), and chemical composition analysis. Results: Thirty samples were collected and visually analyzed. Seven samples were randomly evaluated via scanning electron microscopy. In all the examinations, no relevant changes were reported. Chemical composition analysis also relieved no changes in the chemical structure of the titanium. Conclusions: The titanium-base abutments do not alter the structure and properties of the material, not creating phase changes or the birth of oxides such as to induce fragility. Further clinical studies with longer follow-up periods are needed to confirm these preliminary results.

Clinical assessment of different implant-supported esthetic crown systems fabricated with semi-digital workflow: Two-year prospective study

OBJECTIVE

To assess the clinical outcome of three esthetic implant-supported crown systems fabricated with semi-digital workflow and their influence on the clinical outcome of dental implants.

MATERIAL AND METHODS

A total of 30 participants had received dental implants restoring missing maxillary first/second premolars. After 6 weeks, customized zirconia abutments were early loaded. Two months later, the definitive crowns were fabricated using semi-digital workflow and cemented. According to the crown material, 3 groups were randomly allocated; group (Z): ultrahigh-translucent monolithic zirconia, group (C): resin-matrix ceramic and group (P): polyetherketoneketone veneered with light-cured composite resin. Clinical outcomes including the survival and success rates were evaluated at baseline, 6, 12, 18, and 24 months.

RESULTS

The survival rate for all studied groups was 100%, while their success rate was 100% for group (Z) and 90% for group (C) and group (P). Based on the functional implant prosthodontic score, a statistically significant difference was detected between group (Z) and group (P) (p < 0.001) as well as between group (C) and group (P) (p = 0.01).

CONCLUSIONS

The zirconia group had the most favorable clinical behavior, while the polyetherketoneketone had the least. All crown systems had comparable success rates with similar values of the peri-implant marginal bone loss.

CLINICAL SIGNIFICANCE

Using semi-digital workflow, ultrahigh-translucent monolithic zirconia, resin-matrix ceramic and polyetherketoneketone veneered with light-cured composite resin can be considered as favorable implant-supported crowns. The implant-supported crown system based on polyetherketoneketone veneered with light-cured composite resin is counted as a promising esthetic and restorative option.

Model-free digital workflow and immediate functional loading of implant-supported monolithic glass-ceramic crowns: A case series

OBJECTIVES

The aim of this study is to evaluate surgical and prosthetic outcomes of immediate functional loading of implants with glass-ceramic screw-retained single crowns.

METHODS

A total of 22 implants were placed. Within 24 hours, functional full-contour glass ceramic crowns were delivered to patients. The amount of attached gingiva, Simplified Oral Hygiene Index Score, bleeding on probing, time after extraction, bone type, implant size, soft tissue thickness, primary stability, a general fit of the restoration, occlusal and proximal contacts were recorded. Restorations were followed-up at 1, 3, and 6 months tracking marginal bone loss (MBL), noting changes in occlusal and interproximal contacts, checking other possible complications.

RESULTS

One implant failed and was removed after 4 weeks (95.5 % survival rate). The rest of the implants and crowns functioned with no complications during the follow-up period of 6 months. Factors such as time after extraction, bone type, implant size, soft tissue thickness, and primary stability recorded in Ncm and implant stability quotient (ISQ) values, were not associated with MBL (p<0.05). Mean MBL was found to be 0.3 mm (standard deviation = 0.42) mesially and 0.4 mm (standard deviation = 0.66) distally. One distal and one mesial proximal contact were found to be missing at the 6-month check-up appointment.

CONCLUSIONS

Within the limits of this study, fully digital workflow without a 3D printed model could be successfully employed for immediate functional loading with single-unit implant-supported crowns. Further studies are needed to obtain long-term results with a larger sample of patients.

CLINICAL SIGNIFICANCE

Model-free digital workflow and immediate functional loading of implant-supported monolithic glass-ceramic crown might be viable option to restore a single tooth defect.

Acceptance and experience of digital dental technology, burnout, job satisfaction, and turnover intention for Taiwanese dental technicians

BACKGROUND

Digital dental technology (DDT) has progressed and been introduced to Taiwan in the recent years, gradually changing the industry ecology. Many studies have demonstrated that DDT is more accurate and faster than conventional dental technology. However, there is a paucity of research exploring dental technicians' perspectives on digital dental techniques, and their burnout, job satisfaction, and turnover intention.

METHODS

This cross-sectional survey with convenience sampling was conducted at the conference venue of the Taiwan Association of Dental Technology to investigate the perspectives of dental technicians. We used the snowballing method in this study; two sampling methods were adopted, a convenience sampling of dental technicians to complete a survey, followed by asking the survey participants of the convenience sample to invite their colleagues to participate in the online survey. The survey questionnaire included questions on demographics, work-related information, acceptance and experiences of dental technicians toward DDT, occupational burnout, job satisfaction, and turnover intention. Regression models were used to determine the predictors of job satisfaction and determinants of turnover intention.

RESULTS

In total, 341 valid questionnaires were obtained. Overall, the participants reported long working hours (95.5%), positive score on the DDT acceptance scale, moderate job satisfaction, higher personal burnout, and work burnout, along with lower over-commitment. Among them, 32.9% and 28.2% reported the intention to leave their organization and profession, respectively. The stepwise multiple regression model revealed that higher work burnout decreased job satisfaction, while higher DDT acceptance and position as employer increased job satisfaction. The binary logistic regression models revealed that geographical area of workplace, work burnout, and job satisfaction were significant predictors of turnover intentions.

CONCLUSIONS

Many Taiwanese dental technicians reported turnover intentions and higher burnout. With the trend of digitalization in the dental industry, even though most dental technicians had a positive outlook toward DDT, its influence on job satisfaction appears limited. Retaining good and professional talents required of a dental technician is crucial, especially as Taiwan's dental care becomes increasingly specialized. Strategies for improving the work environment and occupational health of dental technicians should thus be the focus of future studies.

Digitally prefabricated versus conventionally fabricated implant-supported full-arch provisional prosthesis: a retrospective cohort study

Background

To evaluate and compare the clinical outcomes of digitally prefabricated and conventionally fabricated implant-supported full-arch provisional prostheses.

Methods

In this retrospective study, a total of 39 patients (22 males and 17 females) who underwent implant-supported full-arch rehabilitation using the All-on-4 concept with an immediate loading protocol were included: 20 patients treated with digitally prefabricated provisional prostheses were assigned into Group A, and 19 patients treated with conventionally fabricated provisional prostheses were assigned into Group B. Implant/provisional prosthesis survival rates and complications were reviewed. Marginal bone loss (MBL) was investigated by CBCT. Surgical time, restorative time, and total operative time were analyzed. Postoperative pain and swelling were evaluated with the visual analog scale (VAS). The oral health impact profile (OHIP) questionnaire was administered before and after surgery.

Results

The implant/provisional prosthesis survival rate was 100%, and complications appeared with low frequency in both groups, while the mean MBL was 0.30 ± 0.29 mm in Group A and 0.31 ± 0.41 mm in Group B after 3~ 6 months (P > 0.05). The average restorative time in Group A (116.16 ± 16.61 min) was significantly shorter than that in Group B (242.11 ± 30.14 min) (P < 0.05). Patients in Group A showed lower pain/swelling VAS scores after surgery than Group B (P < 0.05). Low OHIP scores with high satisfaction with the overall effects were shown in both groups.

Conclusion

Prefabricated prostheses reduced the prosthetic time and postoperative discomfort in patients whose immediate rehabilitation was based on the All-on-4 concept. This prefabrication technology may be a predictable alternative to improve the short-term clinical outcome of implant-supported full-arch provisional rehabilitation.

In Vitro Comparison of Three Intraoral Scanners for Implant-Supported Dental Prostheses

With continuing technological developments, there have been advances in the field of fixed prosthetics, particularly in impression-taking techniques. These technological advances mean that a wide variety of diagnostic and/or rehabilitation possibilities can be explored without the need for physical models. The aim of this study was to evaluate the accuracy of three intraoral scanners used in oral implant rehabilitation using an extraoral scanner as a reference and varying the scanning area. Three models representing different clinical scenarios were scanned 15 times by each intraoral scanner and three times by the extraoral scanner. The readings were analyzed and overlaid using engineering software (Geomagic^® Control X software (Artec Europe, Luxembourg)). Statistically significant differences in accuracy were found between the three intraoral scanners, iTero^® (Align Technology Inc., San Jose, CA, USA), Medit^® (Medit^®: Seoul, Korea), and Planmeca^® (Planmeca^®: Helsinki, Finland). In all clinical scenarios, the iTero^® scanner had the best trueness (24.4 μm), followed by the Medit^® (26.4 μm) and Planmeca^® (42.1 μm). The Medit^® showed the best precision (18.00 μm) followed by the iTero^® (19.20 μm) and Planmeca^® (34.30 μm). We concluded that the iTero^® scanner had the highest reproducibility and accuracy in the clinical setting.

Restorative angle of zirconia restorations cemented on non-original titanium bases influences the initial marginal bone loss: 5-year results of a prospective cohort study

Aim

To assess radiographic, restorative, clinical and technical outcomes as well as patient satisfaction of directly veneered zirconia restorations cemented on non‐original titanium bases over 5 years.

Material and Methods

Twenty‐four patients with a single missing tooth in the aesthetic zone were recruited. All patients received a two‐piece implant with a screw‐retained veneered zirconia restoration cemented extraorally on a titanium base abutment. Marginal bone levels (MBL), marginal bone changes, technical complications, patient satisfaction and clinical parameters including probing depth, bleeding on probing and plaque index were assessed at crown delivery (baseline), at 1 year (FU‐1) and 5 years (FU‐5) of follow‐up. To investigate the relationship between restorative angle and MBL as well as marginal bone changes (bone loss/bone gain), correlation tests and linear regression models were carried out.

Results

Twenty‐two patients were available for re‐examination at 5 years. The mean MBL amounted to 0.54 ± 0.39 mm at baseline, and to 0.24 ± 0.35 at FU‐5 (=bone gain) (p < .001). At FU‐1, a positive correlation (r = .5) between the mesial restorative angle and mesial MBL was found (p = .012). Marginal bone changes between baseline and FU‐1 at mesial sites were also positively correlated with the mesial restorative angle (r = .5; p = .037). Linear and logistic regression models confirmed that mesial marginal bone loss was significantly associated with the mesial restorative angle at FU‐1 (p < .05). At 5 years, these significant associations at mesial sites disappeared (p > .05). At distal sites, no correlations or associations between the restorative angle and MBL or marginal bone changes were found regardless of the time point. During the 5‐year follow‐up, 5 technical complications occurred, mainly within the first year and mostly chippings. All patients were entirely satisfied with their implant‐supported restoration at 5 years.

Conclusion

Within the limitations of the present study, the restorative angle of implant‐supported crowns on non‐original titanium bases might influence the initial marginal bone loss but without affecting their favourable long‐term clinical performance. A restorative angle of <40° may limit the initial marginal bone loss at implant‐supported crowns with titanium bases.

Digital Workflow for Immediate Implant Placement and Chairside Provisionalization in the Esthetic Zone

Introduction

Immediate implant placement and immediate chairside provisionalization in the esthetic zone require meticulous treatment planning. A digital workflow that combines intraoral scans and a cone beam computed tomography scan can be used to visualize the surgical and restorative aspects of the treatment and to plan a prosthetically driven implant position. A digital workflow in implant dentistry enables the prefabrication of an individualized CAD/CAM temporary restoration, based on the planned implant position. This could be a predictable method to deliver a screw-retained temporary restoration, directly after static computer-assisted immediate implant surgery. Interventions. Three patients with a failing tooth in the maxillary esthetic zone were treated with immediate implant placement and chairside provisionalization using this digital workflow. After 3 months, a final restoration was placed. Clinical, radiographic, and patient-reported outcome measures were collected prior to implant treatment, 6 weeks after placing the temporary restoration and then 1 month and 1 year after placing the final restoration. Outcomes. At the 1-year follow-up, healthy soft tissues were observed, and peri-implant bone levels were stable. Patient satisfaction after the treatment was high.

Conclusion

The three reported cases demonstrate the potential for predictable immediate implant placement and chairside provisionalization using a digital workflow.

Efficiency of occlusal and interproximal adjustments in CAD-CAM manufactured single implant crowns - cast-free vs 3D printed cast-based

PURPOSE

The aim of this study was to evaluate the efficiency of occlusal and interproximal adjustments of single implant crowns (SIC), comparing a digital cast-free approach (CF) and a protocol using 3D printed casts (PC).

MATERIALS AND METHODS

A titanium implant was inserted at position of lower right first molar in a typodont. The implant position was scanned using an intraoral scanner and SICs were fabricated accordingly. Ten crowns (CF; n = 10) were subject to a digital cast-free workflow without any labside occlusal and interproximal modifications. Ten other identical crowns (PC) were adjusted to 3D printed casts before delivery. All crowns were then adapted to the testing model, simulating chair-side adjustments during clinical placement. Adjustment time, quantity of adjustments, and contact relationship were assessed. Data were analyzed using SPSS software (P < .05).

RESULTS

Median and interquartile range (IQR) of clinical adjustment time was 02:44 (IQR 00:45) minutes in group CF and 01:46 (IQR 00:21) minutes in group PC. Laboratory and clinical adjustment time in group PC was 04:25 (IQR 00:59) minutes in total. Mean and standard deviation (±SD) of root mean squared error (RMSE) of quantity of clinical adjustments was 45 ± 7 µm in group CF and 34 ± 6 µm in group PC. RMSE of total adjustments was 61 ± 11 µm in group PC. Quality of occlusal contacts was better in group CF.

CONCLUSION

Time effort for clinical adjustments was higher in the cast-free protocol, whereas quantity of modifications was lower, and the occlusal contact relationship was found more favourable.

Mechanical Stability of Screw-Retained Monolithic and Bi-layer Posterior Hybrid Abutment Crowns after Thermomechanical Loading: An In Vitro Study

To evaluate the failure-load and survival-rate of screw-retained monolithic and bi-layered crowns bonded to titanium-bases before and after mouth-motion fatigue, 72 titanium-implants (SICvantage-max, SIC-invent-AG) were restored with three groups (n = 24) of screw-retained CAD/CAM implant-supported-single-crowns (ISSC) bonded to titanium-bases: porcelain-fused-to-metal (PFM-control), porcelain-fused-to-zirconia (PFZ-test) and monolithic LDS (LDS-test). Half of the specimens (n = 12/group) were subjected to fatigue in a chewing-simulator (1.2 million cycles, 198 N, 1.67 Hz, thermocycling 5–55 °C). All samples were exposed to single-load-to-failure without (PFM0, PFZ0, LDS0) or with fatigue (PFM1, PFZ1, LDS1). Comparisons were statistically analyzed with t-tests and regression-models and corrected for multiple-testing using the Student–Neuman–Keuls method. All PFM and LDS crowns survived fatigue exposure, whereas 16.7% of PFZ showed chipping failures. The mean failure-loads (±SD) were: PFM0: 2633 ± 389 N, PFM1: 2349 ± 578 N, PFZ0: 2152 ± 572 N, PFZ1: 1686 ± 691 N, LDS0: 2981 ± 798 N, LDS1: 2722 ± 497 N. Fatigue did not influence load to failure of any group. PFZ ISSC showed significantly lower failure-loads than monolithic-LDS regardless of artificial aging (p < 0.05). PFM ISSC showed significantly higher failure loads after fatigue than PFZ (p = 0.032). All ISSC failed in a range above physiological chewing forces. Premature chipping fractures might occur in PFZ ISSC. Monolithic-LDS ISSC showed high reliability as an all-ceramic material for screw-retained posterior hybrid-abutment-crowns.

Effect of additional reference objects on accuracy of five intraoral scanners in partially and completely edentulous jaws: An in vitro study

STATEMENT OF PROBLEM

The effect of additional reference objects on the accuracy of different intraoral scanners for partially and completely edentulous patients has not been investigated sufficiently.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of an additional reference object in the form of additional artificial landmarks on the trueness and precision of different intraoral scanners in partially and completely edentulous areas.

MATERIAL AND METHODS

Partially and completely edentulous models with 2 and 4 implants (BLT, RC, Institut Straumann AG), respectively, were used in the study. For the digital scan, scan bodies (CARES Mono Scanbody) were attached, and reference data obtained by using industrial scanners. Ten digital scans of the same model were made with each intraoral scanner: PRIMESCAN, TRIOS 3, TRIOS 4, Carestream 3600, and Medit. Then, additional artificial landmarks were attached, and 10 more intraoral scans were made with each device. Computer-aided design files of the scan bodies were aligned to obtain 3-dimensional surfaces with reference and test scanners. Trueness and precision of distance, angulations, and vertical shift between scan bodies were estimated. The Mann-Whitney Wilcoxon or Student 2-sample t test was applied to estimate statistically significant differences between groups (α=.05).

RESULTS

In the partially edentulous model, distance trueness mean ±standard deviation values ranged from -46.7 ±15.4 μm (TRIOS 3) to 392.1 ±314.3 μm (Medit) in models without additional artificial landmarks. When additional artificial landmarks were applied, trueness of distance mean ±standard deviation values ranged between -35 ±13 μm (TRIOS 4) and 117.7 ±232.3 μm (CARESTREAM). Trueness mean ±standard deviation values of angulation varied from -0.0 ±0.5 degrees (CARESTREAM) to 0.2 ±0.0 degrees (PRIMESCAN) without additional artificial landmarks and from 0.0 ±0.2 degrees (TRIOS 3) to 0.4 ±0.5 degrees (CARESTREAM) with additional artificial landmarks. Vertical shift trueness measurements varied from -108 ±47.1 μm (TRIOS 4) to 107.2 ±103.5 μm (Medit) without additional artificial landmarks and from -15.0 ±45.0 μm (CARESTREAM) to -86.9 ±42.1 μm (TRIOS 4) with additional artificial landmarks. The additional artificial landmark technique improved the trueness of all measured parameters for the 5 tested intraoral scanners. No statistically significant differences were found among models with or without additional artificial landmarks, except for Medit in all parameters and PRIMESCAN in angle measurements (P<.05). The best precision for distance was found with TRIOS 3 and with PRIMESCAN for angulation and vertical shift. Larger deviations were observed in the completely edentulous situation. The effect of additional artificial landmarks was limited when the accuracy parameters of digital scans were considered.

CONCLUSIONS

Scans with and without additional artificial landmarks of partially edentulous conditions scanned by any of the intraoral scanners tested did not influence precision and trueness, except for Medit i500 in the distance and vertical shift parameters and CARESTREAM3600 in vertical shift. Precision and trueness of digital scans of completely edentulous areas were affected, except for Medit i500 for distance, PRIMESCAN and TRIOS 4 for angle, and all systems except TRIOS 4 for vertical shift precision.

Influence of age and scanning system on the learning curve of experienced and novel intraoral scanner operators: A multi-centric clinical trial

OBJECTIVES

To evaluate the effect of age and intra-oral scanner (IOS) on the learning curve of inexperienced operators.

METHODS

Thirty-four operators pertaining to 1 of 3 groups: (G1) students ≤ 25 years (y), (G2) dentists ≥ 40y, and (G3) a control group of experienced IOS operators (no age limitation), were included. All participants performed baseline and final quadrant scans on a volunteer subject, before and after a training program of 3 sessions, with two different IOS: TRIOS 3 (S1) and True Definition (S2). Baseline and final scanning times were registered in seconds. A Pearson correlation was applied to evaluate the correlation between age and scanning time. An ANOVA of repeated measures test was applied to evaluate inter-group (G1, G2, G3) and inter-system performance. Significance level was set at a = 0.05.

RESULTS

Age and scanning time for inexperienced operators showed a weak positive correlation for final scanning time (r = 0.29, p < 0.05). When comparing groups and filtering by IOS, S1 failed to show differences between groups (p > 0.05). With S2, the control group demonstrated a better performance than G2 (p < 0.05), while G1 only demonstrated a better performance than G2 at final scanning time (p = 0.005). Overall, the type of IOS had a significant impact on the scanning time (p < 0.001).

CONCLUSION

Results from this study indicate that age and type of IOS have an impact on the performance and learning curve of inexperienced IOS operators.

CLINICAL SIGNIFICANCE

Gaining knowledge on how different aspects, such as age, experience or IOS system, influence the learning curve to IOSs is relevant due to the financial and strategical impact associated with the acquisition of an IOS.

Many Moving Pieces: Virtual Preoperative Surgical Planning for Traumatic Occlusal Splints

INTRO

Achieving anatomic reduction and re-establishing premorbid occlusion in patients with complex maxillomandibular fractures is challenging even for seasoned surgeons. Historically, surgeons have utilized occlusal splints to help establish occlusal relationships before fracture reduction and fixation. These acrylic splints are fabricated from dental impressions and require manual repositioning of tooth bearing segments along the fracture line to reapproximate premorbid occlusion. The process is laborious, requires a dental lab, and is less efficacious in edentulous patients or those with significantly comminuted fractures; as such it has largely fallen out of practice. Recently, with advances in virtual 3D modeling and printing, we demonstrate that occlusal splints can be designed from computed tomography scans, manipulated virtually, and printed without obtaining impressions from the patient.

METHODS/RESULTS

In our series of 3 patients with complex maxillomandibular fractures, occlusal splints were created by 1) obtaining maxillofacial computed tomography scans, 2) reducing the fractures virtually, and 3) using orthognathic virtual surgery software to create the splint. The time between planning and delivery of the splint was 4 to 7 days. These splints were successfully utilized to help establish premorbid occlusion in conjunction with maxillomandibular fixation and aided in expeditious intraoperative fracture reduction and fixation.

CONCLUSIONS

In the treatment of complex facial fractures, occlusal splints can be a useful adjunct in the operative reduction and fixation of fractures. With the advent of virtual preoperative surgical planning via 3D modeling and 3D printing, these occlusal splints can be created of a sufficient fidelity to avoid the strict need for dental impressions.

Effects of Artificial Tooth Brushing and Hydrothermal Aging on the Mechanical Properties and Color Stability of Dental 3D Printed and CAD/CAM Materials

This study analyzed the surface roughness and waviness, Vickers hardness (VHN), and color changes of six types of 3D printed resins and computer-aided design/computer-aided manufacturing (CAD/CAM) materials after artificial toothbrushing. The average surface roughness height (Ra) change of Formlabs denture teeth A2 resin (FMLB) was not significant between after artificial toothbrushing (0.17 ± 0.02 μm and 0.17 ± 0.05 μm, respectively; mean ± standard deviation). However, the Ra value increased significantly in all remaining groups. Regarding waviness, polymethylmethacrylate (PMMA) had the largest increases in average waviness height (Wa) and maximum surface waviness height (Wz) between, before (0.43 ± 0.23 μm and 0.08 ± 0.02 μm), and after (8.67 ± 4.03 μm, 1.30 ± 0.58 μm) toothbrushing. There were no significant changes in Wa for Formlabs denture teeth A2 resin (FMLB) and NextDent C&B (NXT). After artificial toothbrushing, the dispersed-filler composite (DFC) group had the largest color difference (ΔE, of 2.4 ± 0.9), and the remaining materials had smaller changes than the clinical acceptance threshold of ΔE = 2.25. The VHN of FMLB and NXT were 9.1 ± 0.4 and 15.5 ± 0.4, respectively, and were not affected by artificial toothbrushing. The flexural strengths of the 3D printed materials were 139.4 ± 40.5 MPa and 163.9 ± 14.0 MPa for FMLB and NXT, respectively, which were similar to those of the polycarbonate and PMMA groups (155.2 ± 23.6 MPa and 108.0 ± 8.1 MPa, respectively). This study found that the evaluated 3D printed materials had mechanical and optical properties comparable to those of CAD/CAM materials and were stable even after artificial toothbrushing and hydrothermal aging.

Patient-reported outcome measures (PROMs) of implant-supported reconstructions using digital workflows: A systematic review and meta-analysis

OBJECTIVES

To summarize the existing evidence on patient-reported outcome measures (PROMs) of implant-supported restorations fabricated using a digital workflow in comparison to conventional manufacturing procedures.

METHODS

A PICO strategy was executed using an electronic and manual search focusing on clinical studies evaluating PROMs of implant-supported restorations. Only clinical trials assessing conventional versus digital workflows for implant-supported restorations were included. PROMS on implant impression procedures and fabrication of final restorations were evaluated using random and fixed effects meta-analyses, while implant planning/placement was reported descriptively.

RESULTS

Among 1062 titles identified, 14 studies were finally included, and only seven studies were eligible for meta-analysis. For implant planning and placement, only a qualitative analysis was possible due to heterogeneity between the studies. For impression procedures, the random effects model revealed statistically significant differences in taste, anxiety, nausea, pain, shortness of breath, and discomfort in favor of optical impressions. No significant difference in the subjective perception of the duration of an impression could be reported. For the final fabrication of restorations, no significant difference between veneered and monolithic posterior restorations was found in terms of esthetic, function, and general satisfaction.

CONCLUSION

Most of the studies reporting about PROMs were published during the last ten years and limited to implant-supported single crowns in the posterior region. Based on PROMs, no scientifically proven recommendation for guided implant placement could be given at this time. Patients showed high preference for optical impressions, whereas no differences between veneered and monolithic restorations could be reported.

Production time, effectiveness and costs of additive and subtractive computer-aided manufacturing (CAM) of implant prostheses: A systematic review

OBJECTIVE

To systematically review the dental literature for clinical studies reporting on production time, effectiveness and/or costs of additive and subtractive computer-aided manufacturing (CAM) of implant prostheses.

MATERIALS AND METHODS

A systematic electronic search for clinical studies from 1990 until June 2020 was performed using the online databases Medline, Embase and Cochrane. Time required for the computer-aided design (CAD) process, the CAM process, and the delivery of the CAD-CAM prostheses were extracted. In addition, articles reporting on the effectiveness and the costs of both manufacturing technologies were included.

RESULTS

Nine clinical studies were included reporting on subtractive CAM (s-CAM; 8 studies) and additive CAM (a-CAM; 1 study). Eight studies reported on the s-CAM of prosthetic and auxiliary components for single implant crowns. One study applied a-CAM for the fabrication of an implant bar prototype. Time was provided for the CAD process of implant models (range 4.9-11.8 min), abutments (range 19.7-32.7 min) and crowns (range 11.1-37.6 min). The time for s-CAM of single implant crown components (abutment/crown) ranged between 8.2 and 25 min. Post-processing (e.g. sintering) was a time-consuming process (up to 530 min). At delivery, monolithic/veneered CAD-CAM implant crowns resulted in additional adjustments chairside (51%/93%) or labside (11%/19%).

CONCLUSIONS

No scientific evidence exists on production time, effectiveness and costs of digital workflows comparing s-CAM and a-CAM. For both technologies, post-processing may substantially contribute to the production time. Considering effectiveness, monolithic CAD-CAM implant crowns may be preferred compared to veneered CAD-CAM crowns.

A systematic review and meta-analysis evaluating the survival, the failure, and the complication rates of veneered and monolithic all-ceramic implant-supported single crowns

Objective

To assess the survival, failure, and complication rates of veneered and monolithic all‐ceramic implant‐supported single crowns (SCs).

Methods

Literature search was conducted in Medline (PubMed), Embase, and Cochrane Central Register of Controlled Trials until September 2020 for randomized, prospective, and retrospective clinical trials with follow‐up time of at least 1 year, evaluating the outcome of veneered and/or monolithic all‐ceramic SCs supported by titanium dental implants. Survival and complication rates were analyzed using robust Poisson's regression models.

Results

Forty‐nine RCTs and prospective studies reporting on 57 material cohorts were included. Meta‐analysis of the included studies indicated an estimated 3‐year survival rate of veneered‐reinforced glass‐ceramic implant‐supported SCs of 97.6% (95% CI: 87.0%–99.6%). The estimated 3‐year survival rates were 97.0% (95% CI: 94.0%–98.5%) for monolithic‐reinforced glass‐ceramic implant SCs, 96.9% (95% CI: 93.4%–98.6%) for veneered densely sintered alumina SCs, 96.3% (95% CI: 93.9%–97.7%) for veneered zirconia SCs, 96.1% (95% CI: 93.4%–97.8%) for monolithic zirconia SCs and only 36.3% (95% CI: 0.04%–87.7%) for resin‐matrix‐ceramic (RMC) SCs. With the exception of RMC SCs (p < 0.0001), the differences in survival rates between the materials did not reach statistical significance. Veneered SCs showed significantly (p = 0.017) higher annual ceramic chipping rates (1.65%) compared with monolithic SCs (0.39%). The location of the SCs, anterior vs. posterior, did not influence survival and chipping rates.

Conclusions

With the exception of RMC SCs, veneered and monolithic implant‐supported ceramic SCs showed favorable short‐term survival and complication rates. Significantly higher rates for ceramic chipping, however, were reported for veneered compared with monolithic ceramic SCs.

Time-efficiency and cost-analysis comparing three digital workflows for treatment with monolithic zirconia implant fixed dental prostheses: A double-blinded RCT

OBJECTIVES

This double-blinded randomized controlled trial investigated economic performance indicators (EPI) in terms of time-efficiency and production costs of 3-unit monolithic zirconium-dioxide (ZrO2) implant fixed dental prostheses (iFDP) in three different workflows.

METHODS

Twenty patients with two Straumann Tissue-Level-Implants received three iFDPs; two were fabricated in proprietary complete digital workflows with intraoral optical scanning and model-free fabrication with company-related CAD/CAM lab-software while one iFDP was manufactured on digitized casts from conventional impressions. The sequence of impression-taking for the three workflows (TRIOS 3/3Shape [Test-1]; Virtuo Vivo/Dental Wings [Test-2]; Impregum/3M Espe [Control]) was randomly allocated. Sixty iFDPs bonded to ti-base abutments were analyzed. Clinical and technical worksteps for Test-1/Test-2/Control were recorded and evaluated for time-efficiency including cost-analysis (CHF=Swiss Francs) using ANOVA-Tests (significance level α=0.05).

RESULTS

Mean total work time, as the sum of clinical plus technical steps, was 97.5 min (SD ± 23.6) for Test-1, 193.1 min (SD ± 25.2) for Test-2, and 172.6 min (SD ± 27.4) for Control. Times were significantly different between Test-1/Test-2 (p < 0.00001), Test-1/Control (p < 0.00001), and Test-2/Control (p < 0.03610). Technical costs were 566 CHF (SD ± 49.3) for Test-1, 711 CHF (SD ± 78.8) for Test-2, 812 CHF (SD ± 89.6) for Control, and were also significantly different for all comparisons (p < 0.00001).

CONCLUSIONS

Test-1 demonstrated the best performance for time-efficiency, Test-2 revealed the worst result. This indicates that digital workflows are not the same and not necessarily superior to analog workflows of monolithic ZrO2 iFDPs. Complexity decreases by reducing the number of steps following complete digital workflows, resulting in lower production costs compared to the mixed analog-digital workflow with conventional impressions.

CLINICAL SIGNIFICANCE

Complete digital workflows comprising intraoral optical scanning without physical models for treatment with monolithic ZrO2 iFDPs is an efficient alternative to mixed analog-digital workflows with conventional impressions and labside digitization of dental casts.

A Double-Blind Crossover RCT Analyzing Technical and Clinical Performance of Monolithic ZrO2 Implant Fixed Dental Prostheses (iFDP) in Three Different Digital Workflows

This double-blind randomized controlled trial with a crossover design analyzed the technical and clinical performance of three-unit monolithic ZrO₂ implant-fixed dental prostheses (iFDPs), prepared using two complete digital workflows (Test-1, Test-2) and one mixed analog–digital workflow (Control). Each of the 20 study patients received three iFDPs, resulting in 60 restorations for analysis. The quality of the restorations was assessed by analyzing laboratory cross-mounting and calculating the chairside adjustment time required during fitting. All iFDPs could be produced successfully with all three workflows. The highest cross-mounting success rate was observed for the original pairing iFDP/model of the Control group. Overall, 60% of iFDPs prepared with Test-1 workflow did not require chairside adjustment compared with 50% for Test-2 and 30% for Controls. The mean total chairside adjustment time, as the sum of interproximal, pontic, and occlusal corrections was 2.59 ± 2.51 min (Control), 2.88 ± 2.86 min (Test-1), and 3.87 ± 3.02 min (Test-2). All tested workflows were feasible for treatment with iFDPs in posterior sites on a soft tissue level type implant system. For clinical routine, it has to be considered that chairside adjustments may be necessary, at least in every second patient, independent on the workflow used.

Failure Load of Monolithic Lithium Disilicate Implant-Supported Single Crowns Bonded to Ti-base Abutments versus to Customized Ceramic Abutments after Fatigue

PURPOSE

This laboratory study analyzed the influence of retention mode (screw- vs cement retained) and fatigue application on the failure load of monolithic lithium-disilicate (LDS) implant-supported single crowns (ISSC).

MATERIAL AND METHODS

A total of 72 samples of monolithic LDS (*Ivoclar Vivadent) ISSC were divided into three groups (n = 24) according to their type of retention mode: Group Ti-CAD: Titanium base (SICvantage CAD/CAM Abutment red (SIC invent AG), screw-retained milled monolithic LDS (IPS e.max CAD*); Group Ti-P: Titanium base (SICvantage CAD/CAM Abutment red), screw-retained pressed monolithic LDS (IPS e.max Press*) and Group Ti-Cust: Titanium base with cemented press LDS (IPS e.max Press*) crown on a LDS (IPS e.max Press*) custom abutment. A mandibular first molar implant-supported single crown model was investigated (Titanium implant: SICvantage-max, SIC invent AG, diameter: 4.2 mm, length: 11.5 mm). Half of each group (n = 12) w​ere exposed to fatigue with cyclic mechanical loading (F = 198 N, 1.2 million cycles) and simultaneous thermocycling (5-55°C). Single load to failure testing was performed, before (Subgroups Ti-CAD, Ti-P, and Ti-Cust) and after (Subgroups Ti-CAD-F, Ti-P-F, and Ti-Cust-F) fatigue. Weibull distribution was used to determine the characteristic strength and Weibull modulus differences between groups. Probability of survival at 900N load was calculated.

RESULTS

No samples failed during fatigue. Characteristic strength values were as follow: Ti-CAD: 3259.5N, Ti-CAD-F: 2926N, Ti-P: 2763N, Ti-P-F: 2841N, Ti-Cust: 2789N, Ti-Cust-F: 2194N. Whereas no difference was observed between pressed or milled monolithic crowns cemented to Ti-base, regardless of loading condition, fatigue decreased the characteristic strength of crowns cemented to custom abutments. Probability of survival at 900 N was not significantly different between groups.

CONCLUSIONS

Screw-retained pressed or milled monolithic LDS ISSC, cemented directly to Ti-base abutments or LDS crowns cemented to custom ceramic abutments resist physiological chewing forces after simulated 5-year aging in the artificial mouth and presented equally high probability of survival. However, a significant decrease in load to failure was observed in LDS crowns cemented to custom ceramic abutments after fatigue. Prospective clinical trials are needed to confirm the results of this laboratory investigation.

Accuracy of implant impression techniques with a scannable healing abutment

STATEMENT OF PROBLEM

Scannable healing abutments are a convenient option to facilitate impression making for implant-supported restorations. However, studies evaluating the accuracy of the impression technique with scannable healing abutments are lacking.

PURPOSE

The purpose of this in vitro study was to evaluate the accuracy of implant impression techniques with scannable healing abutments.

MATERIALS AND METHODS

A partially edentulous mandibular dentiform model was fabricated with an epoxy resin, and implants were placed in the mandibular right second premolar and first molar areas. A maxillary dentiform model was then fabricated, and both models were mounted on an articulator. Scan data were obtained from the mounted models and set as the reference scans. The experimental models were divided into 4 groups (n=10). The conventional pick-up impression technique and definitive casts were used in group CI. The scan data from the definitive casts were obtained with a 3D model scanner. An intraoral scanner with a digital body scan was used in group DS. Group MS yielded definitive casts with dual-arch impressions with scannable healing abutments. The fabricated definitive casts were mounted and scanned with a 3D cast scanner. Intraoral scanning with scannable healing abutments was used in group IS. In all 4 groups, the interarch relationship in the maximum intercuspal position was obtained by scanning the facial aspect. The center of the implant head was set as a measurement point for linear intra-arch deviations and implant angle deviations. The mesiopalatal cusp tip of the maxillary right first molar was used to calibrate the linear interarch deviations. The data obtained from each group were compared with the data from the reference scan. As the data were not normally distributed, the Kruskal-Wallis test and Bonferroni correction were used for the analysis (α=.05).

RESULTS

Group MS exhibited significantly higher deviations in linear intra-arch and implant angles compared with the other groups (P<.05). No significant difference was found between the groups in linear interarch deviations (P>.05).

CONCLUSIONS

The accuracy of intraoral scanning with scannable healing abutments was comparable with that of conventional pick-up impression techniques and digital scans with scan bodies. However, model scanning with scannable healing abutments may not be clinically acceptable for implant impressions.

Patient preference and clinical working time between digital scanning and conventional impression making for implant-supported prostheses: A systematic review and meta-analysis

STATEMENT OF PROBLEM

The technology behind optical scanners has greatly improved recently, making their dental application advantageous. While their accuracy is now comparable with that of conventional impression materials, whether these techniques have other advantages is unclear.

PURPOSE

The purpose of this systematic review and meta-analysis was to determine whether digital scanning for implant-supported restorations is more time-efficient and convenient for the patient.

MATERIAL AND METHODS

The study was conducted on September 23, 2020 using 4 different databases (Medline, Cochrane, Web of Science, Scopus) searching for clinical studies that compared the time needed and/or patient perceptions between those who had undergone the digital scanning procedure and those who had undergone conventional impression making.

RESULTS

Twelve studies met the inclusion criteria for qualitative and quantitative analysis. Outcome variables were measured as standard mean differences (SMDs) by following a fixed-effects model or random-effects model (in the case of high heterogeneity). Digital scanning was more time-efficient and was preferred by patients for all 4 analyzed outcomes (comfort, anxiety, nausea, time perception).

CONCLUSIONS

Digital scanning was found to be more time-efficient and convenient than conventional impression making for implant-supported restorations. Additional randomized controlled trials are needed to confirm the findings of this review.

A Review of the Major Prosthetic Factors Influencing the Prognosis of Implant Prosthodontics

Background: The treatment plan of prosthetic restorations supported by dental implants requires comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A comprehensive review of the literature was conducted with a PICO (Patient Intervention Comparison Outcomes) question: “For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?”. A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS * OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%), or prospective evaluations of prosthesis with various kinds of events (18%). However, narrative reviews of literature (14%) and in vitro/animal studies (16%) were also found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.