“All-on-4” Immediate-Function Concept for Completely Edentulous Maxillae: A Clinical Report on the Medium (3 Years) and Long-Term (5 Years) Outcomes

The effect of short implants placed in the posterior region on tilted implants in the 'All-On-Four' treatment concept: a three-dimensional finite element stress analysis

This study aims to investigate the impact of a short implant placed behind the mental foramen with the all-on-four treatment concept using the three-dimensional (3D) finite element stress analysis (FEA). Six different finite element analysis models were designed according to tilted implant angle (17° and 30°), presence of short implants, and short implant diameter (4.1 mm and 4.8 mm). A 100 N force was applied vertically from the central fossa of the lower right second premolar tooth. Maximum equivalent (von Mises) and Minimum/Maximum principal (Pmin/Pmax) stress values and distributions were evaluated by 3D-FEA. The highest stress value among tilted implants was in the T17 group. T30 was the group that caused the most stress in the cortical bone. Adding the short implant to the all-on-four design reduced von Mises stress on multi-unit abutments, abutment screws, and tilted implants in both the 17° and 30° groups. At the same time, it reduced Pmin/Pmax stresses in cortical bone. Similar behavior was observed in terms of stress values and distributions for the 4.1 and 4.8 mm short implant groups. The results show that short implant placement in the posterior region in the all-on-four concept reduces stress on the bone, implants, and prosthetic parts, regardless of the diameter of the short implant. In cases where biomechanical risks such as parafunctional habits and poor bone quality increase, we recommend increasing the number of implants with short implants.

Retention of titanium copings to implant-supported fixed dental prostheses

PURPOSE

The aim of this in vitro study was to assess the effects of using different cements and titanium copings designs on the retention of implant-supported fixed dental prostheses (IFDPs) using a pull-out test.

MATERIALS AND METHODS

Fifty zirconia (ZirCAD; Ivoclar Vivadent) and 20 prepolymerized denture acrylic resin (AvaDent) rectangular (36 mm × 12 mm × 8 mm) specimens were milled to mimic the lower left segmental portion of the All-on-Four IFDPs. Cylindrical titanium copings (Variobase; Straumann) (V) were used in 2 prepolymerized denture acrylic resin groups (n = 10) while conical titanium copings (Straumann) (C) were used as a control group for zirconia with 4 groups using cylindrical titanium copings. Before cementation, the outer surfaces of all titanium copings and the intaglio bonding surface of prosthetic specimens were airborne-particle abraded. All specimens were cemented following the manufacturer's recommendations and instructions according to the experimental design. After artificial aging (5000 cycles of 5°C 55°C, dwelling time 20 s; 150 N, 1.5 Hz in a 37°C water bath), all specimens were subjected to retention force testing using a pull-out test using a universal testing machine and a custom fixture with a crosshead speed 5 mm/min. Modes of failure were classified as Type 1, 2, or 3. Retention force values were analyzed by the t-test for the prepolymerized denture acrylic resin specimen groups, and 1-way ANOVA and the Tukey test for the zirconia groups at α = 0.05.

RESULTS

Mean and standard deviation retention force values varied from 101.1 ± 67.1 to 509.0 ± 65.2 N for the prepolymerized denture acrylic resin specimen groups. The zirconia groups ranged from 572.8 ± 274.7 to 1416.1 ± 258.0 N. There is no statistically significant difference in retention force values between V and C specimens cementing to zirconia with Panavia SA cement (Kuraray Noritake) (p = 0.587). The retention forces and failure modes were influenced by the cement used (p < 0.05). Modes of failure were predominantly Type 2 (mixed failure) and Type 1 (adhesive fracture from prosthetic materials) except for the quick-set resin group (Type 3, adhesive failure from coping).

CONCLUSIONS

When bonding IFDPs onto titanium copings, quick-set resin provided significantly higher retention force for prepolymerized denture acrylic resin prostheses. Conical and cylindrical titanium copings performed similarly when cemented to zirconia with Panavia SA cement under the same protocol. The stability of the bonded interface and retention forces between zirconia prostheses and titanium copings varied from the cement used.

A comparative analysis of the passivity of fit of complete arch implant-supported frameworks fabricated using different acquisition techniques

STATEMENT OF PROBLEM

The accuracy of intraoral scanners (IOSs) in recording edentulous jaws has improved recently. However, improvement in accuracy does not necessarily imply the clinical validity of the scans, and limited information is available regarding the manufacture of passively fitting prostheses.

PURPOSE

The purpose of this in vitro study was to analyze the passivity of complete arch screw-retained frameworks fabricated using different acquisition techniques.

MATERIAL AND METHODS

A 3-dimensional maxillary edentulous model to receive all-on-4 screw-retained frameworks was prototyped. Eighteen polymethylmethacrylate (PMMA) frameworks were fabricated with a 5-axis milling machine and divided into 3 groups according to the acquisition technique (n=6): scanned by using an IOS (CEREC Primescan; Dentsply Sirona), scanned with the aid of an auxiliary device by using the same IOS, and by using a conventional impression and then scanning the stone cast with an extraoral scanner (EOS). The passivity of fit of the frameworks was tested with the 1-screw test, the terminal screw of the framework assembly was tightened on the multiunit abutment (MUA), and the vertical marginal gap (µm) was measured at the other 3 framework-to-abutment interfaces by using a digital microscope at ×40 magnification. A modification to the 1-screw test was analyzed by tightening all screws and then unscrewing all except 1 of the anterior abutments. Data were explored for normality by using the theoretical quantile-quantile (Q-Q) plots and the Shapiro-Wilk test of normality. The Friedman test compared data between the different acquisition techniques; the tightening methods and locations (buccal and palatal) were used as the block variable. The post hoc Dunn test was used when the Friedman test was significant. The Kruksal-Wallis test compared the data from the 2 groups of the tightening methods and the 2 location groups. The aligned rank transformation (ART) ANOVA test was used for the interaction effects among the 3 variables. A multiway ANOVA was applied to the ranked data. (α=.05 for all tests).

RESULTS

Significant differences were found among all groups (P<.001). Regarding the passivity of fit, the mean vertical marginal gap was 50 µm for frameworks fabricated from an intraoral scan with the aid of an auxiliary device, 62 µm for frameworks fabricated by using an IOS, and 140 µm for frameworks fabricated by using an EOS. No significant difference was found among all groups regarding the tightening method (P=.355) or location measured (P=.175).

CONCLUSIONS

Digital scanning with the aid of an auxiliary device resulted in the best fit; however, digital approaches with or without the auxiliary device resulted in a more accurate fit with a smaller marginal gap than with the conventional impression.

Outcomes that may affect implant and prosthesis survival and complications in maxillary fixed prosthesis supported by four or six implants: A systematic review and meta-analysis

Objective

To investigate whether the clinical and radiographical outcomes are affected when four or six implants support the maxillary fixed complete denture (FCD).

Materials and methods

This study was registered on PROSPERO (CRD42021226432) and followed the PRISMA guidelines. The focused PICO question was, "For an edentulous maxillary patient rehabilitated with an implant-supported fixed prosthesis, do the clinical and radiographical outcomes differ when four or six implants support the prosthesis ". A thorough search of the relevant studies was designed and performed electronically. The survival rate of implant and prosthesis, marginal bone loss, and complications (mechanical and biological) were the primary outcomes, whereas implant distribution and using the surgical guide, follow-up, and framework material were evaluated as secondary outcomes.

Results

Out of 1099 articles initially retrieved, 53 clearly stated the outcomes of interest and were included in this study. There were no significant differences in implant and prosthesis survival, technical/mechanical complications, and biological complications between the 4-implant group (4-IG) and the 6-implant group (6-IG). However, marginal bone loss (MBL) was significantly higher in the 4-IG (p < 0.01). The surgical guide and follow-up period did not significantly affect implant/prosthesis survival. Additionally, using the CAD/CAM milled framework and anteroposterior implant distribution were associated with significantly higher implant survival in the 6-IG (p < 0.01).

Conclusion

The findings of this study indicated that having a greater number of implants, as seen in the 6-implant group, can lead to a decrease in technical and biological complications and reduce marginal bone loss. It is worth noting that factors such as using CAD/CAM frameworks and the anteroposterior distribution of implants were recognized as important in improving implant survival rates when more implants are present.

Marginal fit and fracture resistance of polyetheretherketone, zirconia, and titanium implant-supported prosthesis frameworks for a partially edentulous arch after thermomechanical aging

STATEMENT OF PROBLEM

Although polyetheretherketone (PEEK) and zirconia (Zir) have been used as implant-supported prosthesis (ISP) frameworks, the long-term effects of thermomechanical aging on the marginal fit and fracture resistance of PEEK and Zir ISP frameworks with titanium (Ti) bases for patients with a partially edentulous arch are not clear.

PURPOSE

The purpose of this in vitro study was to determine the marginal fit and fracture resistance of PEEK and Zir ISP frameworks with Ti bases and Ti ISP frameworks for partially edentulous arches after aging.

MATERIAL AND METHODS

A total of 30 ISP epoxy resin casts were obtained from a typodont with 1 straight implant (Nobel Biocare) in the mandibular right canine region and 1 implant with a 30-degree distal tilt in the mandibular right first molar region. All frameworks (n=10) were fabricated on their own epoxy resin cast with multiunit abutment replicas by using a computer-aided design and computer-aided manufacturing system (exocad-Yenadent). The PEEK and Zir frameworks were fabricated with Ti-bases. Primer (MKZ) and resin cement (DTK adhesive) were used to cement the frameworks to the Ti-bases under a static load of 10 N. After thermomechanical aging (1.2×106 cycles, 120 N, 5 °C-55 °C), marginal gaps between the Ti-bases and cemented frameworks and vertical and passive fits between the Ti-bases and framework and multi-unit abutments were measured by using a stereomicroscope (Euromex) at ×100 magnification. Fracture resistances and types were then determined by using a universal test machine and a stereomicroscope at ×40 magnification. Data were analyzed by using 1-way analysis of variance (ANOVA) and the Tukey HSD and Fisher-Freeman-Halton tests (α=.05).

RESULTS

The marginal gaps of the PEEK and Zir frameworks were respectively 83.5 ±27.1 and 81.8 ±17.8 µm. PEEK (23.7 ±4.6) and Zir (32.9 ±8.7) had a better vertical fit (µm) than Ti (52.5 ±10.6) (P<.001). Zir (49.3 ±16.2) (P<.001) and PEEK (70.9 ±19.6) (P>.05) frameworks had better passive fit (µm) than Ti (91.3 ±24.2). Ti had the highest mean fracture resistance (N) (14800.2 ±3442.3) followed by Zir (7318.7 ±1385.1) and PEEK (3448.9 ±486.6) (P<.001). Fracture types were different in different groups (P<.001).

CONCLUSIONS

The PEEK and Zir frameworks with Ti bases had better vertical and passive fit than the Ti frameworks. All ISP frameworks represented mean marginal fit below 92 µm and withstood physiologic occlusal forces after thermomechanical aging.

Implant survival rate and marginal bone loss with the all-on-4 immediate-loading strategy: A clinical retrospective study with 1 to 4 years of follow-up

STATEMENT OF PROBLEM

Assessing peri-implant marginal bone loss (MBL) and its risk factors with cone beam computed tomography (CBCT) may clarify the risk factors for the all-on-4 (5 or 6) strategy and further improve its survival rate.

PURPOSE

The purpose of this retrospective clinical study was to evaluate the implant survival rate, MBL, and associated risk factors of all-on-4 (5 or 6) prostheses after 1 to 4 years of follow-up with CBCT.

MATERIAL AND METHODS

A total of 56 participants rehabilitated with 325 implants by using the all-on-4 (5 or 6) concept between October 2015 and December 2019 were included. Outcome measures were cumulative implant survival (life-table analysis) and MBL. Four CBCT scans, a scan immediately after surgery (T0), a scan 1 year after surgery (T1), a scan 2 years after surgery (T2), and a scan 3 to 4 years after treatment (T3), were obtained to evaluate the MBL. The Pearson correlation coefficient analysis and linear mixed models were performed to assess the potential risk factors for MBL (α=.05).

RESULTS

The implant survival rate was 99.38%, and the prosthesis survival rate was 100%. The reductions in the vertical buccal bone height (△VBBH) were 0.74 ±0.10 mm (T0-T1), 0.37 ±0.12 mm (T1-T2), and 0.15 ±0.14 mm (T2-T3). Except for T2-T3, the △VBBH showed a significant difference at T0-T1 and T1-T2 (P≤.05). The alterations in vertical mesial bone height (VMBH), vertical distal bone height (VDBH), and vertical lingual bone height (VLBH) were similar to the trend observed in VBBH. The △VBBH (T0-T3) was negatively correlated with the horizontal buccal bone thickness (HBBT) (T0) (r=-.394, P<.001). Linear mixed models revealed that factors such as smoking (P=.001), mandible implant site (P<.001), immediate implant (P=.026), tilted implant (P<.001), female sex (P=.003), systemic disease (P=.025), and bruxism (P=.022) negatively affected MBL. The cantilever length (CL) also had a negative effect on MBL around the implants at the distal extension (P<.001).

CONCLUSIONS

The high implant and prosthesis survival rates and low MBL confirmed the predictability of the all-on-4 (5 or 6) concept. Smoking, mandible implant site, systemic disease, bruxism, female sex, immediate implant, tilted implant, and CL were identified as potential risk factors for MBL.

Functional and aesthetic rehabilitation using 'all on 4' treatment protocol with intraoral welding

With the increasing life expectancy and improved quality of life, the conventional prosthodontic removable treatment modalities are being replaced with implant retained fixed prostheses. A full-arch conventional rehabilitation of edentulous ridges requires six to ten dental implants. However, some patients demand fixed implant-supported prostheses inspite of medical conditions and economic concerns. Also in completely edentulous cases, the insufficient bone morphology directs the treatment plan towards alternatives such as cantilever prostheses, short implants or ridge augmentation procedures. These clinical conditions have brought in a quantum shift in treatment planning towards the 'all on 4 protocol' providing immediately loaded fixed prosthesis supported by 4 implants thereby providing optimum and immediate restoration of function and esthetics.

The All-on-four concept for fixed full-arch rehabilitation of the edentulous maxilla and mandible: a longitudinal study in Japanese patients with 3-17-year follow-up and analysis of risk factors for survival rate

PURPOSE

Implant-supported immediately loaded fixed full-arch rehabilitation via All-on-four treatment yields good long-term results for both the maxilla and the mandible. However, the risk factors affecting long-term implant survival are unknown, and the long-term prognosis of All-on-four concept procedures in Japanese individuals has not been elucidated. We aimed to determine the cumulative implant survival rate after 3-17-year follow-up and identify the associated risk factors.

METHODS

We analysed 561 cases (307 maxillae, 254 mandibles) with 2364 implants (1324 maxillae, 1040 mandibles) that received All-on-four treatment. We investigated the cumulative implant- and patient-level survival rates and various risk factors for implant failure. Statistical analysis was performed using the log-rank test for differences in Kaplan-Meier curves, univariate analysis using the Chi-square test, and multivariate analysis for risk factors affecting the survival rate.

RESULTS

The cumulative survival rate was 94.4% by patient level and 97.4% by implant level for the maxilla, and 96.7% by patient level and 98.9% by implant for the mandible, with up to 17 years of follow-up. The maxillary survival rate at the implant level was significantly lower (p < 0.05). Furthermore, the maxillary survival rate within 24 months was significantly lower at the implant level (p < 0.01). Multivariate analysis revealed that the maxilla was the most significant risk factor (p < 0.01).

CONCLUSIONS

All-on-four treatment yielded high long-term survival rates in Japanese patients. However, the maxilla showed a significantly lower cumulative survival rate than the mandible, while early failure was significantly higher. Furthermore, the maxilla was a significant risk factor influencing the survival rate.

Evaluation of Tension and Deformation in a Mandibular Toronto Bridge Anchored on Three Fixtures Using Different Framework Materials, Abutment Systems, and Loading Conditions: A FEM Analysis

OBJECTIVE

 The aim of this study was to investigate by finite element method analysis the behaviour of a three-implant mandible Toronto framework made by three different materials, with two abutment systems and two loading conditions.

MATERIALS AND METHODS

 Three implants were virtually inserted in a mandible model in positions 3.6, 4.1, and 4.6. Three prosthetic framework bars with the same design and dimension (4.8 × 5.5 mm) were projected. The variables introduced in the computer model were the framework materials (glass fiber reinforced resin, Co-Cr, TiAl6V4), the abutment systems (Multi-Unit-Abutment [MUA]/OT-Bridge), and the loading conditions (500 N vertical load on all the framework area and 400 N on a 7-mm distal cantilever). The computer was programmed with physical properties of the materials as derived from the literature. Maximum tension and deformation values for each variable were registered at framework, screws, and abutment level and then compared.

RESULTS

 Metal frameworks Cr-Co and TiAl6V4 resulted in lower deformation than glass fiber-reinforced resin frameworks while presenting higher tension values. The OT-Bridge exhibited lower maximum tension and deformation values than the MUA system. The first loading condition reached higher tension and deformation values than the second and it resulted in more uniformly distributed load on all the framework area, especially with the OT-Bridge system.

CONCLUSION

 More rigid materials and OT-Bridge system decrease the deformation on the prosthetic components. Tension stresses are more uniformly distributed with glass fiber-reinforced resin, in the OT-Bridge system and avoiding cantilever loading.

Guided Full Mouth Implant Rehabilitation in Atrophic Alveolar Ridges Using TTPHIL ALL TILT® Protocol: A Case Report With Three Years Follow-Up

Computer-assisted implant planning has become a key diagnostic and therapeutic tool in modern dentistry. This case report emphasizes the possibilities in modern implantology combining virtual implant planning, guided surgery with surgical templates, and immediate function. A 75-year-old female presented with maxillary and mandibular dentures and wanted fixed replacement in minimal appointments. Diagnosis, decision-making, and treatment approaches were based on clinical findings and detailed virtual three-dimensional implant planning. Guided implant placement of six implants in each arch using Tall and Tilted Pin Hole Immediate Loading Technique (TTPHIL ALL TILT®), and immediate loading with a provisional fixed dental prosthesis (FDP) was performed fulfilling patient's functional and esthetic demands in a minimally invasive manner. The final computer-assisted design/computer-assisted manufacturing (CAD/CAM) FDP with a titanium framework and ceramic layering was delivered after six months. At the three-year recall, the implant-supported FDP was free of any complications. Uneventful osseointegration of the dental implants and a healthy peri-implant mucosa were observed. Computer-assisted TTPHIL ALL TILT® technique including three-dimensional virtual implant planning, guided surgery, and CAD/CAM fabrication of provisional and final reconstructions allowed for a concise treatment workflow with favorable esthetic and functional outcomes in this maxillary and mandibular full-mouth case without the need of multiple surgeries in a short treatment time.

Evaluation of Prosthetic Marginal Fit and Implant Survival Rates for Conventional and Digital Workflows in Full-Arch Immediate Loading Rehabilitations: A Retrospective Clinical Study

Digital impression provides several advantages in implant prosthodontics; however, its use in full-arch rehabilitations, especially immediately after surgery, has yet to be validated. The aim of this study was to retrospectively analyse the fit of immediate full-arch prostheses, fabricated using conventional or digital impressions. Patients requiring a full-arch immediate loading rehabilitation were divided into three groups: T1 (digital impression taken immediately after surgery), T2 (Preoperative digital impression, guided surgery-prefabricated temporary bridge) and C (conventional impression taken immediately after surgery). Immediate temporary prostheses were delivered within 24 h after surgery. X-rays were obtained at the time of prosthesis delivery and at the 2-year follow-up. Primary outcomes were cumulative survival rate (CSR) and prosthesis fit. Secondary outcomes were marginal bone level (MBL) and patient satisfaction. One hundred and fifty patients were treated from 2018 to 2020, with 50 in each group. Seven implants failed during the observation period. The CSR was 99% for T1, 98% for T2 and 99.5% for C. A statistically significant difference in prosthesis fit was found among T1 and T2 vs. C. A statistically significant difference was found in the MBL between T1 and C. The outcomes of the present study suggest that digital impression is a viable alternative to conventional protocols for the realisation of full-arch immediate loading prostheses.

Immediate loaded fixed complete dentures supported by implants in patients with a history of periodontitis: A retrospective cohort study of 2 to 7 years

STATEMENT OF PROBLEM

The outcome of implant-supported fixed complete dentures in edentulous patients with a history of periodontitis is unclear.

PURPOSE

The purpose of this retrospective clinical study was to assess the clinical outcomes of immediate loaded fixed complete dentures in individuals with a history of periodontitis and to analyze risk factors related to implant failure.

MATERIAL AND METHODS

A total of 642 implants (146 prostheses) in 119 patients were included. The follow-up period ranged from 2 to 7 years. Implant survival rates, marginal bone loss, mechanical complications, biologic complications, and patient satisfaction were evaluated. The Pearson chi-square test, independent samples t test, and multivariate generalized estimating equation were performed for statistical analysis (α=.05).

RESULTS

Eleven implants in 9 patients failed, leading to overall survival rates of 98.3% at the implant level and 92.4% at the patient level. The mean ±standard deviation marginal bone loss was 0.62 ±0.86 mm, and marginal bone loss did not differ significantly between axial and tilted implants (P>.05). Mechanical complications were detected in 55 (37.7%) definitive prostheses; biologic complications were detected in 318 (49.5%) implants. Smokers had a significantly lower survival rate than nonsmokers (odds ratio: 6.880, P=.013). Bruxers had a significantly higher incidence of mechanical complications than nonbruxers (P<.001).

CONCLUSIONS

The immediate loaded fixed complete denture supported by implants is a suitable treatment option for edentulous patients with a history of periodontitis, with high survival implant rates. Smoking is a risk factor for implant failure. Bruxism may increase the incidence of mechanical complications with implant-supported fixed complete dentures, and the overall biologic complication incidence is comparatively high.

Comparison of 4‐ or 6‐implant supported immediate full‐arch fixed prostheses: A retrospective cohort study of 217 patients followed up for 3–13 years

PURPOSE

Choosing four or six implants to support immediate full-arch fixed prostheses (FAFPs) is still controversial worldwide. This study aims to analyze and compare the long-term results of All-on-4 and All-on-6.

MATERIALS AND METHODS

This retrospective cohort study enrolled 217 patients rehabilitated with 1222 implants supporting 271 FAFPs, including 202 prostheses supported by 4 implants (All-on-4 group) and 69 prostheses supported by 6 implants (All-on-6 group), and followed up for 3-13 years. Implant survival, prosthesis survival, complications, and implant marginal bone loss (MBL) were evaluated and compared between two groups. Patient characteristics including age, gender, jaw, opposite dentition condition, smoking habit, bruxism, bone quantity and quality, cantilever length (CL), prosthesis material, and oral hygiene were analyzed to assess their influence on the clinical results of the two groups. Six surgeons and three prosthodontists who performed FAFPs more than 5 years were invited for questionnaires, to assess patient- and clinician-related influences on implant number.

RESULT

In general, All-on-4 group indicated no significant difference with All-on-6 group in the implant survival (implant-level: hazard ratio [HR] = 1.0 [95% confidence interval (CI): 0.8-1.2], P = 0.96; prosthesis-level: HR = 0.8 [95% CI: 0.3-1.8], P = 0.54), prosthesis survival (odds ratio [OR] = 0.8 [95% CI: 0.3-2.8], P = 0.56), biological complications (OR = 0.9 [95% CI: 0.5-1.8], P = 0.78), technical complications of provisional prosthesis (OR = 1.3 [95% CI: 0.7-2.3], P = 0.42), technical complications of definitive prosthesis (OR = 1.1 [95% CI: 0.6-2.2], P = 0.33) and the 1st, 5th, and 10th year MBL (P = 0.65, P = 0.28, P = 0.14). However, for specific covariates, including elderly patients, opposing natural/fixed dentition, smoking, bruxism, long CL, low bone density, and all acrylic provisional prostheses, All-on-6 was more predictable in some clinical measurements than All-on-4. The implant prosthodontists and the medium-experienced clinicians showed significant preference for All-on-6 (P < 0.05).

CONCLUSION

Based on this study, the long-term clinical results showed no significant difference between All-on-4 and All-on-6 groups in general. However, for some specific characteristics, All-on-6 seemed to be more predictable in some clinical measurements than All-on-4. For the clinicians' decision-making, medium-experienced clinicians and the implant prosthodontists showed significant preference for All-on-6.

Biomechanical investigation of maxillary implant-supported full-arch prostheses produced with different framework materials: a finite elements study

PURPOSE

Four and six implant-supported fixed full-arch prostheses with various framework materials were assessed under different loading conditions.

MATERIALS AND METHODS

In the edentulous maxilla, the implants were positioned in a configuration of four to six implant modalities. CoCr, Ti, ZrO₂, and PEEK materials were used to produce the prosthetic structure. Using finite element stress analysis, the first molar was subjected to a 200 N axial and 45° oblique force. Stresses were measured on the bone, implants, abutment screw, abutment, and prosthetic screw. The Von Mises, maximum, and minimum principal stress values were calculated and compared.

RESULTS

The maximum and minimum principal stresses in bone were determined as CoCr < ZrO₂ < Ti < PEEK. The Von Mises stresses on the implant, implant screw, abutment, and prosthetic screws were determined as CoCr < ZrO₂ < Ti < PEEK. The highest Von Mises stress was 9584.4 Mpa in PEEK material on the prosthetic screw under 4 implant-oblique loading. The highest maximum principal stress value in bone was found to be 120.89 Mpa, for PEEK in 4 implant-oblique loading.

CONCLUSION

For four and six implant-supported structures, and depending on the loading condition, the system accumulated different stresses. The distribution of stress was reduced in materials with a high elastic modulus. When choosing materials for implant-supported fixed prostheses, it is essential to consider both the number of implants and the mechanical and physical attributes of the framework material.

Biomechanical Comparison of Asymmetric Implant Configurations for All-on-Four Treatment Using Three-Dimensional Finite Element Analysis

The aim of this study is to examine the effect of unilaterally more posterior placement of implants (Straumann BLT 4.1 mm in diameter and 12 mm long) applied according to the all-on-four concept on the stress distribution on bone, implants, and other prosthetic components, using the finite element analysis method. Three scenarios were modelled: For Model 1 (M1), anterior implants were placed symmetrically perpendicular to the bone in the right and left lateral incisor region, while the necks of the posterior implants placed symmetrically in the second premolar region were angled at 30 degrees. For Model 2 (M2) the implant in the left second premolar region was placed to the first molar region unilaterally. For Model 3 (M3) the implant in the left lateral incisor region was placed to the canine region unilaterally. Vertical and oblique forces (100 N) were applied in the right first molar region. The von Mises and maximum (Pmax) and minimum (Pmin) principal stresses were obtained. The highest stress concentration on the cortical bone was observed in the second premolar region in all models when oblique forces were applied. M1 was highest (8.992 MPa) followed closely by M3 (8.780 MPa) and M2 was lowest (3.692 MPa). The highest stress concentration on the prosthetic parts was observed in this framework when oblique forces were applied. M2 was highest (621.43 MPa) followed by M3 (409.16 MPa) and the lowest was M1 (309.43 MPa). It is thought that placing the implant further posterior to first molar region may prevent the bone resorption that occurs with high stress around the crestal bone. However, increased stress on the implants and prosthetic parts may lead to failures.

Evaluation of Load Distribution in a Mandibular Model with Four Implants Depending on the Number of Prosthetic Screws Used for OT-Bridge System: A Finite Element Analysis (FEA)

In full-arch implant rehabilitations, when the anterior screw abutment channel compromises the aesthetic of the patient, the OT-Bridge system used with its Seeger rings may provide the necessary retention of the prosthesis. However, no studies have evaluated the forces generated at the Seeger level during loading. This Finite Element Analysis aims to investigate the mechanical behavior of Seeger rings in a mandibular model with four implants and an OT-Bridge system, used without one or two anterior prosthetic screws. A 400 N unilateral load was virtually applied on a 7 mm distal cantilever. Two different variables were considered: the constraint conditions using two or three screws instead of four and the three different framework materials (fiberglass reinforced resin, cobalt-chrome, TiAl6V4). The FEA analysis exhibited tensile and compressive forces on the Seeger closest to the loading point. With the resin framework, a tension force on abutment 3.3 generates a displacement from 5 to 10 times greater than that respectively expressed in metal framework materials. In a full-arch rehabilitation with four implants, the case with three prosthetic screws seems to be a safer and more predictable configuration instead of two. Considering the stress value exhibited and the mechanical properties of the Seeger, the presence of only two prosthetic screws could lead to permanent deformation of the Seeger in the screwless abutment closest to the loading point.

Mechanobiologically optimized Ti-35Nb-2Ta-3Zr improves load transduction and enhances bone remodeling in tilted dental implant therapy

The tilted implant with immediate function is increasingly used in clinical dental therapy for edentulous and partially edentulous patients with excessive bone resorption and the anatomic limitations in the alveolar ridge. However, peri-implant cervical bone loss can be caused by the stress shielding effect. Herein, inspired by the concept of “materiobiology”, the mechanical characteristics of materials were considered along with bone biology for tilted implant design. In this study, a novel Ti–35Nb–2Ta–3Zr alloy (TNTZ) implant with low elastic modulus, high strength and favorable biocompatibility was developed. Then the human alveolar bone environment was mimicked in goat and finite element (FE) models to investigate the mechanical property and the related peri-implant bone remodeling of TNTZ compared to commonly used Ti–6Al–4V (TC4) in tilted implantation under loading condition. Next, a layer-by-layer quantitative correlation of the FE and X-ray Microscopy (XRM) analysis suggested that the TNTZ implant present better mechanobiological characteristics including improved load transduction and increased bone area in the tilted implantation model compared to TC4 implant, especially in the upper 1/3 region of peri-implant bone that is “lower stress”. Finally, combining the static and dynamic parameters of bone, it was further verified that TNTZ enhanced bone remodeling in “lower stress” upper 1/3 region. This study demonstrates that TNTZ is a mechanobiological optimized tilted implant material that enhances load transduction and bone remodeling.

•

The mechanical properties and deformation mechanisms of Ti–35Nb–2Ta–3Zr alloys were studied.

•

The cell biocompatibility, a layer-by-layer correlation of the finite element and X-ray Microscopy analysis were evaluated.

•

Ti–35Nb–2Ta–3Zr implant improves load transduction and enhances bone remodeling in tilted implantation models.

•

Mechanobiologically optimized Ti–35Nb–2Ta–3Zr alloy meets the clinical application requirements of tilted implant therapy.

Mechanical response of different frameworks for maxillary all-on-four implant-supported fixed dental prosthesis: 3D finite element analysis

This study's purpose is to assess the stress distribution in the peri-implant bone, implants, and prosthetic framework using two different posterior implant angles. All-on-four maxillary prostheses fabricated from feldspathic-ceramic-veneered zirconia-reinforced lithium silicate (ZLS) and feldspathic-ceramic-veneered cobalt-chromium (CoCr) were designed with 17 or 30-degree-angled posterior implants. Posterior cantilever and frontal vertical loads were applied to all models. The distribution of maximum and minimum principal stresses (σmax and σmin) and von Mises stress (σVM) was evaluated. Under posterior cantilever load, with an increase in posterior implant angle, σmax decreased by 4 and 7 MPa in the cortical bone when ZLS and CoCr were used as a prosthetic framework, respectively. Regardless of the framework material, 17-degree-angled posterior implants showed the highest σVM (541.36 MPa under posterior cantilever load; 110.79 MPa under frontal vertical load) values. Regardless of the posterior implant angle, ZLS framework showed the highest σVM (91.59 MPa under posterior cantilever load; 218.99 MPa under frontal vertical load) values. Increasing implant angle from 17 to 30° caused a decrease in σmax values in the cortical bone. Designs with 30-degree posterior implant angles and ZLS framework material may be preferred in All-on-four implant-supported fixed complete dentures.

How do implant threads and diameters affect the all-on-four success? A 3D finite element analysis study

BACKGROUND: The effect of different thread designs and diameters on the all-on-four concept is unclear. OBJECTIVE: The aim of the study was to clarify the differences in stress distribution of dental implants with various thread designs and diameters based on the all-on-four concept with three dimensional (3D) finite element analysis (FEA). METHODS: A 3D model of a totally edentulous mandible was used to perform the FEA. Four different models (M1, M2, M3, and M4) including 3.5 and 4.3 mm diameter dental implants with active and passive threaded designs were generated. The dental implants were positioned according to the all-on-four concept. The Von Mises stresses on dental implants and maximum and minimum principal stresses (Pmax and Pmin) on bony structures were calculated under vertical, oblique and horizontal loads. RESULTS: For Von Mises stresses, the highest stress values were detected on the distal implants for all models. Distal implants had also the highest stress values for vertical loading. The Von Mises stresses were found to be concentrated around the implant’s neck. In all models the highest Pmax and Pmin stresses occurred in the bone surrounding the distal implant. It was noted that the active threaded implants showed the highest Pmax and Pmin stress values. CONCLUSION: The implant thread design and diameter might have a strong influence on the stress values in the all-on-four concept.

Accuracy of different laboratory scanners for scanning of implant-supported full arch fixed prosthesis

OBJECTIVE

This study evaluated the accuracy of different laboratory scanners (LS) for scanning of implant-supported full arch fixed prosthesis with different implant angulations.

MATERIALS AND METHODS

Two maxillary models that are designed to receive an all-on-four implant retained prosthesis were fabricated then scanned using five different LS. The models were divided into two groups according to the angulation of the posterior implant (Group 1; 30° and group 2; 45°). Each group was then subdivided into five subgroups according to the type of LS, subgroup T; Medit T710, subgroup I; IneosX5, subgroup E; 3ShapeE4, subgroup A; Autoscan DS-Mix, and subgroup M; Ceramill Map600. An industrial 3D scanner was used as reference scanner, then each model was scanned with 5 LS 10 times. Trueness and precision were analyzed using Geomagic 3D analysis software.

RESULTS

Both scanner type and implant angle had a significant effect on the trueness (p < 0.001). Significant interaction was found between the scanner type and implant angle (p < 0.001). For scanner type tukeys post hoc test revealed highest trueness with the 3Shape E4 (21.3 ± 2.1) and the medit T710 (22.6 ± 2.1) and least trueness with the shining 3D autoscan ds-mix (33.8 ± 3.0). Significantly better trueness was observed with the 30° than the 45° angle. Regarding precision, two-way ANOVA revealed significant effect of the scanner type only (p < 0.001). There were no significant differences between the 3Shape E4, medit T710, Ineos X5, and the Ceramill map600. However, all showed significantly higher precision values when compared to shining 3D autoscan ds-mix.

CONCLUSIONS

All tested scanners showed results within the clinically acceptable range with 3ShapeE4 and Medit T710 showing the highest accuracy.

CLINICAL SIGNIFICANCE

Tested scanners can be used for scanning of All-on-four implant supported prosthesis.

Case Series on the Long-Term Effect of Three Different Types of Maxillary Implant-Supported Overdentures on Clinical Outcomes and Complications

(1) Long-term data on maxillary implant overdentures (IODs) are scarce. This case series evaluated three types of IODs supported by six, four or three implants (Anyridge^®, Mega'Gen Implant Co., Ltd., Daegu, South-Korea), after 3-5 years in function. (2) A total of 31 patients, with 132 implants, were non-randomly allocated based on available bone or financial limitations. IOD-6 received a telescopic overdenture; IOD-4 a bar; and IOD-3, non-connected implants with locator abutments. Implant survival, bone level changes, probing pocket depth (PPD), plaque index, bleeding on probing (BOP), and technical, biological and aesthetic complications were registered. Impact of suprastructures on bone loss and PPD was analyzed using mixed-effect linear regression models. Differences between groups were analyzed using the ANOVA test for BOP, and Kruskal Wallis test for complications. (3) In total, 23 patients participated in the follow-up (9 female, 14 male), with average age of 62.2 years; 7, 11 and 5 patients in IOD-6, IOD-4 and IOD-3, respectively. Implant survival after 4.4 years on average, was 98% in total; 100%, 97.8% and 93.3% for IOD-6, IOD-4 and IOD-3, respectively. Mean bone loss corresponded to 0.68 mm (SD 1.06, range -4.57-1.51), 0.39 mm (SD 1.06, range -3.6-2.43), and 1.42 mm (SD 1.68, range -5.11-0.74) for IOD-6, IOD-4 and IOD-3, respectively. A statistically significant difference was seen in bone level when comparing IOD-6 to IOD-3 (p = 0.044), and IOD-4 to IOD-3 (p = 0.018). Mean PPD was 3.8 mm (SD: 0.69; range 2.5-5.3), 3.5 mm (SD 0.59; range 2.33-5), and 3.2 mm (SD 0.56; range 2-4) for IOD-6, IOD-4 and IOD-3, respectively, and differed significantly between IOD-6 and IOD-3 (p = 0.029). Incidence of peri-implantitis was 1%. No differences were seen for complications between groups. (4) Maxillary IOD supported by four to six implants is the most reliable treatment regarding implant survival and peri-implant health. More research is needed in the clinical outcomes, in particular the peri-implant health, and complications of maxillary IODs, especially with a reduced number of implants.

Ten-year follow-up of full-arch rehabilitations supported by implants in immediate function with nasal and full-length palatine bicortical anchorage on the anterior maxilla

PURPOSE

To evaluate the immediate function of anterior maxillary implants.

METHODS

One hundred nine patients (42 males and 67 females; average age 55.2 years; range 38-81 years) were followed for 10 years. One hundred eighty-eight implants using nasal and full-length palatine cortical anchorage were inserted in the anterior section of the maxilla together with 188 tilted implants placed posteriorly. Outcome measures were implant success and survival, prosthesis survival, bone loss, and the incidence of biological and mechanical complications. Cumulative success and survival were computed through Kaplan-Meyer product limit estimator (at patient level) and life tables (implant level).

RESULTS

Four patients lost one implant each, giving a 10-year cumulative survival rate of 95.8% and 97.7% using the patient and the implant as the unit of analysis, respectively. The prosthesis survival rate was 98.2%, and the average marginal bone loss was 1.79 mm (1.06 mm). The cumulative success rate was 89.1% and 92.5% using the patient and the implant as the unit of analysis, respectively.

CONCLUSION

Full-arch fixed prosthetic rehabilitations supported by immediately functional implants inserted in the anterior maxilla with bicortical anchorage together with posterior-tilted implants are viable in the long term.

Assessment of Preload Loss after Cyclic Loading in the OT Bridge System in an “All-on-Four” Rehabilitation Model in the Absence of One and Two Prosthesis Screws

The aim of this study was to evaluate the stability of prosthetic screws after applying cyclic loadings in an “all-on-four” rehabilitation model with the OT Bridge system. The model was tested both with and without anterior screws. Four implant analogues following the “all-on-four” concept were inserted in an edentulous mandibular resin model. An OT Bridge system with a Cr–Co prosthetic framework was fabricated. Depending on the presence or absence of one or two anterior screws on the implant analogues, three groups were created, i.e., Gr.1: three tightening screws, Gr.2: two tightening screws, Control Group: four tightening screws. Each single group underwent subsequent 400,000 cyclic loads, simulating approximately a year of chewing by using a dynamometer machine. This cycle was repeated five times for each group, and preload loss values were evaluated on each prosthetic screw after each cycle. All the data obtained were analyzed by one-way ANOVA and Student’s t-test. No statistically significant differences after intragroup analysis were found. A statistically significant difference within the Gr.1 between the screws in positions 33 and 36, equal to 15.2% (p-value = 0.0176), was found. The OT Bridge seems a useful system to maintain the retention of a prosthesis during mechanical stress conditions even in the absence of one screw in an “all-on-four” rehabilitation. This could represent a good solution to solve the esthetic problem of the screw buccal access hole for fixed solutions.

Morphometry and displacement analysis of the upper lips following maxillary full-arch implant-supported fixed prostheses: a 3D morphometric study

BACKGROUND

With the emergence of three-dimensional (3D) integration technology, analysis of soft tissue displacement and morphological changes after maxillary full-arch implant-supported fixed prostheses can be performed. The aim of this study was to verify the feasibility of the 3D integration method for constructing the relative position of the prostheses and facial soft tissue, evaluate the displacement and morphological variation of the upper lips after maxillary full-arch implant-supported fixed prostheses.

METHODS

Twenty-five maxillary edentulous patients were recruited in this study. At the time of final prosthesis delivery, the 3D prostheses data and three 3D facial profiles were integrated. After method validation, the 3D position changes of seven soft tissue landmarks were used to reflect the 25 upper lips. The variation of four morphological distances were analyzed to reflect the morphological alteration of the upper lips. Two pairs of dentofacial landmarks were used to analyze the sagittal relative position of the prostheses and soft tissue. The included patients were also grouped to determine the impact of sex, upper lip thickness, and length on lip support changes.

RESULTS

The average distance of the two matched relative reliable forehead regions was only 0.32 mm. The sagittal shifts of labrale superius (LS), stomion (STO), crista philtri left (CPHL) and crista philtri right (CPHR) were 3.44 ± 1.39 mm, 2.52 ± 1.38 mm, 3.04 ± 1.18 mm, and 3.12 ± 1.21 mm, respectively. With the exception of the decrease in the length of subnasale (SN)-LS, the length of cheilion right (CHR)-cheilion left (CHL), CPHR-CPHL, and LS-STO significantly increased. The two pairs of dentofacial landmarks had strong positive movement correlations along the sagittal direction. Patients with thinner and longer lips showed more lip support than those with thicker and shorter lips by a clinically insignificant amount.

CONCLUSIONS

The integration method of 3D facial and dental data showed high repeatability in constructing the dentofacial relative position. The linear equations reflecting dentofacial relative position could aid clinicians in evaluating the restoration effect and estimate the upper lip variation.

Development of a lead foil crown delineation technique for implant rehabilitations to generate patient specific finite element model of occlusal loading points

Understanding the clinical biomechanical basis of dental implant supported functional rehabilitation of edentulous jaws improves precision, longevity and overall success of a planned treatment. Stress distribution pattern around dental implants is an important determinant for rate of bone resorption around them. During planning the treatment for most prosthetic rehabilitations, the surgeon uses a software to virtually plan the dimension, position and angulation of the implants considering only the quantity of available bone in the area of interest but does not usually consider the strain generated around the implants after prosthetically loading them. We hence hypothesise that dental implants not be subjected to abnormal strain they should be positioned and angulated not only based on volume of bone available but also based on the vector of occlusal load. The virtual FEA model to analyse the stress distribution would hence require alveolar bone with future tooth/ teeth in centric relation to be modelled. This paper proposes a simple innovative technique to develop a 3D FE model of occlusal loading surface by using a radio-opaque malleable lead foil to generate a patient specific FE model. This would greatly minimise modelling errors and also help determine the best position of the dental implant based on both the volume of bone in the CT scan and the results of FE analyses.•

Functional rehabilitation using dental implant supported prosthesis needs to be biomechanically analysed to know and understand the stress distribution pattern around the implant.

•

When teeth (Loading points) are missing, patient specific virtual model of occlusal loading points cannot be generated.

•

‘Lead foil crown delineation technique’ helps to generate patient specific 3D model of occlusal surface for load application.

Survival rates of axial and tilted implants in the rehabilitation of edentulous jaws using the All-on-four™ concept: A systematic review

Aim:

The aim of this review was to evaluate the survival rate of axial and tilted implants in rehabilitation of edentulous jaws using all on four concept.

Setting and Design:

Systematic Review.

Materials and Methods:

A literature review was performed in MEDLINE, PubMed Central (PMC), Google scholar, Embase, Cochrane Central Register of Controlled Trials. Hand searches were conducted of the bibliographic of related journals and systematic reviews. A total of 380 articles were obtained from the intial screening process. Of these articles, 25 articles fulfilled the inclusion criteria. The authors performed evaluation of articles independently as well as data extraction and quality assessment.

Statistical Analysis Used:

Qualitative analysis.

Results:

The major prosthetic complication was the fracture of the acrylic prosthesis. The mean cumulative survival rate of implants (72-132 months) were 94% to 98%. The prosthesis survival rate (12 months) was between 99% to 100%. The averaged bone loss was 1.3 ±0.4 mm (12-60 months). No Significant difference was found between survival rates of axial and tilted implants nor between maxilla and mandible.

Conclusion:

All on four concept can be employed successfully in the edentulous patients with resorbed ridges while improving their quality of life and reducing morbidity. However,randomized clinical trials with large sampling size and long term follow up should be incorporated.

Assessment of bone density and stability with immediately loaded dental implants with the All-on-Four technique in free vascularized fibular grafts used for mandibular reconstruction

BACKGROUND

Following free fibula flaps (FFF) reconstruction of mandibular defects the patients need an early dental rehabilitation to regain their masticatory function and enhance their feeding and nutrition.

METHODS

This study included 10 patients, with mandibular defects previously reconstructed with FFF that span the area between the two mandibular angles. They received a full arch fixed restoration supported by four implants using a pilot drilling guide to perform a flapless operation. The stability of the placed dental implants was assessed along with the changes in bone density.

RESULTS

There was a statistically significant increase in stability after 3 and 6 months, and there was a decrease in density after 6 months. The patient satisfaction improved over the follow-up period.

CONCLUSION

The All-on-Four technique is reliable and economic for early functional rehabilitation of resected jaws reconstructed with FFF; however, further studies are needed to investigate the changes in fibula bone density over time and with function.

Implant rehabilitation of edentulous maxilla in digital dentistry: A case report utilizing CAD/CAM technologies

The replacement of missing teeth utilizing dental implants and digital dental technologies has gained significant popularity in daily clinical practice over the last decade. Partially dentate patients present more anatomical references to guide the implant position and prosthetic reconstruction as compared to completely edentulous arches. Therefore, the management of edentulous maxilla using implant digital dentistry represents a challenging clinical situation where a thorough treatment plan is paramount to achieve a final prosthetic result that meets both functional and esthetic requirements. This case report discusses the oral rehabilitation of an edentulous maxilla and partially dentate mandible using a digital workflow for both the surgical and prosthetic phases of the implant therapy. Protocols for clinical assessment, treatment planning, and restorative management are described to provide a predictable and prosthetic-driven treatment for implant-supported prostheses.

Clinical performance of narrow-diameter titanium-zirconium implants in immediately loaded fixed full-arch prostheses: a 2-year clinical study

Objectives

The aim of this study was to evaluate the outcomes of immediate fixed full-arch prostheses supported by axial or tilted narrow-diameter Ti-Zr implants (3.3 mm) (Roxolid®, Institut Straumann® AG, Basel, Switzerland) (NDIs) in combination with standard-diameter implants up to 2 years’ follow-up.

Materials and methods

The study was conducted at Kocaeli University Faculty of Dentistry from 2016 to 2018. 37 jaws of 28 patients with an average age of 52 years were rehabilitated with fixed full-arch prostheses supported by 179 implants. Cumulative survival rate (CSR), implant success, marginal bone loss (MBL), and prosthetic survival rate as well as complications were analyzed.

Results

Total CSR of 99.4% and 98.5% for all and narrow implants respectively have been observed at 2 years’ follow-up. No prosthesis failures were observed, yielding a cumulative prosthetic survival rate of 100%. The NDIs achieved 0.63 mm MBL at 1 year and 1.02 mm at 2 years. The mean MBL at 1 year was 0.51 mm (mandible 0.63 mm/maxilla 0.41 mm) and 0.73 mm (mandible 0.90 mm/maxilla 0.43 mm) at 2 years. Both implant angulation and loading protocol did not influence the MBL.

Conclusions

The combination of narrow-diameter implants with standard-diameter implants in immediate fixed full-arch rehabilitation has a good prognosis to become a new standard of care for severely atrophic jaws.

Clinical relevance

The use of narrow-diameter implants in fixed full-arch rehabilitations in atrophic ridges would be a successful and predictable treatment approach.

Six-year clinical outcomes of implant-supported acrylic vs. ceramic superstructures according to the All-on-4 treatment concept for the rehabilitation of the edentulous maxilla

The aim of the current study was to document the long-term clinical results of the use of two prosthetic techniques for the rehabilitation of completely edentulous maxillae according to the “All-on-Four” concept: Fixed, screw-retained prosthesis mounted on a chrome-molybdenum framework with (1) metal-ceramic veneers and (2) Acrylic prosthesis with acrylic resin prosthetic teeth. A total of 34 patients were assigned to subgroups according to their own preference of the superstructure type (ceramics [n: 17] or acrylic resin [n: 17]). Prosthetic complications, marginal bone loss, plaque accumulation, bleeding on probing, bite force and oral-health-related quality of life were assessed over a period of 6 years. Marginal bone loss around implants of the ceramic group remained well within the limits for ‘success’, as defined by the 2007 Pisa consensus over the time (1.43 ± 0.35 mm). However, marginal bone loss was significantly more pronounced around the implants in the acrylic group (2.15 ± 0.30) and the difference between two groups was statistically significant (p: 0.00). Bleeding on probing and plaque accumulation showed also positive correlation with marginal bone loss. Both acrylic and ceramic suprastructures appeared to be equivalent after 6 years; however, ceramic suprastructures revealed superior clinical results in terms of bone loss and plaque accumulation. Current study determines the long-term clinical outcomes of different prosthetic management alternatives in All-on-Four and aids to increase dental professionals’ ability to meet the patients’ expectations.

Comparative Analysis of the Stability of Prosthetic Screws under Cyclic Loading in Implant Prosthodontics: An In Vitro Study

Background: To compare the loss of preload in absence of loading and after a fixed number of cyclic loadings on 7-mm distal cantilever in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400,000 repeated loadings were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400,000 cyclic loadings; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 min from the tightening in absence of cyclic loadings. Conclusions: Within the limits of the present study, MUA and OT-Bridge may be considered reliable prosthetic anchoring systems able to tolerate repeated cyclic occlusal loads on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening.

Implant and prosthesis survival rates of full-arch immediate prostheses supported by implants with and without bicortical anchorage: Up to 2 years of follow-up retrospective study

OBJECTIVES

To compare implant and prosthesis survival rates between full-arch immediate prostheses supported by 4 hydrophilic implants with bicortical anchorage and by 5 or 6 hydrophilic implants placed without bicortical anchorage.

MATERIAL AND METHODS

The sample was retrospectively selected and comprised completely edentulous patients treated with full-arch immediate prostheses supported by Morse Taper hydrophilic implants. The selected patients were divided into four groups, according to the region of implant placement and type of anchorage. Differences in implant and prosthesis survival rates between groups, as well as the influence of bicortical anchorage on implant primary stability, were verified using Fisher's exact tests (significant at p < .05).

RESULTS

The sample comprised 392 implants, 72 were placed in the maxilla with bicortical anchorage, and 85 were placed without. In the mandible, 140 implants were placed with and 95 were placed without bicortical anchorage. The follow-up period was up to 24 months. A 98.8% implant survival rate was observed for the group of implants placed without bicortical anchorage in the maxilla, and of 100% for the other groups. The overall implant survival rate was 99.7% (391 of 392 implants). Prosthesis survival rate was 100% for all groups. No differences were observed between groups with respect to implant and prosthesis survival rates. Significantly higher primary stability was observed for implants placed with bicortical anchorage in both jaws.

CONCLUSION

Predictable results and high survival rates were achieved within the period evaluated by the present retrospective study, with immediate full-arch prostheses when only four hydrophilic implants are placed bicortically.

Fixed full-arch maxillary prostheses supported by four versus six implants with a titanium CAD/CAM milled framework: 3-year multicentre RCT

OBJECTIVES

This RCT compares marginal bone level (MBL) change and the clinical parameters after a 3-year function in maxillary implant-supported fixed complete dentures (FCDs) treated with four-implants (4-I) or six-implants (6-I).

MATERIAL AND METHOD

Three centres treated 56 patients with 280 implants allocated to the 4-I or 6-I group. Radiographic and clinical examinations were performed. The primary outcome was to investigate MBL change between the groups.

RESULTS

Implant survival rates were 100% and 99% in the 4-I and 6-I groups, respectively. Considering the clustering effects, the MBL change was not significantly different between the groups over the 3-year follow-up. The MBL in the 4-I group was 0.30 ± 0.50 mm at baseline, 0.24 ± 0.31 mm at 1 year and 0.24 ± 0.38 mm at 3 years. In the 6-I group, MBL was 0.14 ± 0.32 mm at baseline, 0.16 ± 0.35 mm at 1 year and 0.12 ± 0.26 mm at 3 years. There was a statistically significant difference between the groups at BL and 3Y. No significant differences between the groups were reported for clinical parameters at each time point as well as in between the visits. The technical and biological complications rates were 1.6% and 6.0%, respectively. Prosthetic complications affected 25 FCDs (47.2%).

CONCLUSION

Marginal bone level change revealed a stable condition in the 3-year period in the two groups. Few technical and biological complications occurred apart from the chipping/fracture of the prosthetic teeth. Four-implant is a feasible solution if the rehabilitation is oriented towards the most cost-effective treatment and towards avoiding bone augmentation procedures. Clinicians have to consider the potential required visits for prosthetic maintenance.

All-on-4 Concept Update

Over the past 17 years, the All-on-4 treatment concept has been a reliable and predictable modality to rehabilitate edentulous jaws with immediate function as full-arch prostheses. This article highlights clinically relevant data compiled by numerous All-on-4 investigators including complications and their remedies, occlusion and cantilever trends, implant size utilization, and controversial topics. We provide insights for navigating the complexities of medically diverse populations, faced by our daily practice, with a focus on patient avoidance, risk factors for implant and prosthetic failures, in hopes to minimize complications so clinicians would choose this treatment with confidence.

[Validation of the digital integration technology for evaluating the nasolabial morphology variation after the cross-arch fixed restoration of maxillary implant-supported prostheses]

OBJECTIVE

To explore the applicability of integration between three-dimensional (3D) facial and dental data to evaluate the nasolabial morphology variation before and after the cross-arch fixed restoration of the maxillary implant-supported prostheses.

METHODS

Twelve patients (4 women and 8 men), mean age (54.82±5.50) years (from 45 to 62 years) referred to the Department of Oral Implan-tology, Peking University School and Hospital of Stomatology, were selected and diagnosed with edentulous maxilla. For all the patients, 4 to 6 implants were inserted into the maxilla. Six months later, the final cross-arch fixed prostheses were delivered. The 3D facial images were collected before and after the final restoration. The 3D data of prostheses were also captured. All the 3D data were registered and measured in the same coordinate system. Then the displacement of all the landmarks [cheilion left (CHL), cheilion right (CHR), crista philtri left (CPHL), crista philtri right (CPHR), labrale supe-rius (LS), subnasale (SN), stomion (STO), upper incisor (UI), upper flange border of the prostheses (F-point, F)], and the variation of the distances between these landmarks (SN-LS, CPHR-CPHL, CHR-CHL, LS-STO) were analyzed and compared.

RESULTS

The consistency test among three measurements of the length of F-SN indicated that the integration method of the dental prostheses and soft tissue had the good repetitiveness, ICC=0.983 (95%CI: 0.957-0.995). After wearing the final cross-arch maxillary implant-supported prostheses, all the landmarks on the soft tissue moved forward. The nasal base area changed minimally, and the shift of SN in the sagittal direction was only (0.61±0.44) mm. But the sagittal shift of LS was (3.12±1.38) mm. In the vertical direction, SN, LS, CPHL, and CPHR moved upward. But STO, CHL, and CHR moved downward a little. Except for the slight decrease of the length of philtrum (SN-LS), the length of CHL-CHR, CPHL-CPHR, and the height of upper lip were increased together (P < 0.01). In the direction of Z axis, the strong correlations were found not only between the movements of SN and F (r=0.904 3) but also between the movements of LS and UI (r=0.958 4).

CONCLUSION

The integration method of 3D facial and dental data showed good repetitiveness. And the strong correlations between the landmarks of prostheses and nasolabial soft tissue in the sagittal direction were found by this new method.

Hybrid Polyetheretherketone (PEEK)-Acrylic Resin Prostheses and the All-on-4 Concept: A Full-Arch Implant-Supported Fixed Solution with 3 Years of Follow-Up

Background: The aim of this three-year prospective study was to examine the outcome of a solution for full-arch rehabilitation through a fixed implant-supported hybrid prosthesis (polyetheretherketone (PEEK)-acrylic resin) used in conjunction with the All-on-4 concept. Methods: Thirty-seven patients (29 females, 8 males), with an age range of 38 to 78 years (average: 59.8 years) were rehabilitated with 49 full-arch implant-supported prostheses (12 maxillary rehabilitations, 13 mandibular rehabilitations and 12 bimaxillary rehabilitations). The primary outcome measure was prosthetic survival. Secondary outcome measures were marginal bone loss, plaque and bleeding scores, veneer adhesion issues, biological complications, mechanical complications, and the patients’ subjective evaluation. Results: There were two patients (maxillary rehabilitations) lost to follow-up, while one patient withdrew (maxillary rehabilitation). One patient with bimaxillary rehabilitation fractured the mandibular PEEK framework, rendering a 98% prosthetic survival rate. Implant survival was 100%. Average (standard deviation) marginal bone loss at 3-years was 0.40 mm (0.73 mm). Veneer adhesion was the only technical complication (n = 8 patients), resolved for all patients. Nine patients (n = 11 prostheses) experienced mechanical complications (all resolved): fracture of acrylic resin crowns (n = 3 patients), prosthetic and abutment screw loosening (n = 4 patients and 3 patients, respectively), abutment wearing (n = 1 patient). One patient experienced a biological complication (peri-implant pathology), resolved through non-surgical therapy. A 90% satisfaction rate was registered for the patients’ subjective evaluation. Conclusions: Based on the results, the three-year outcome suggests the proposed rehabilitation solution as a legitimate treatment option, providing a potential shock-absorbing alternative that could benefit the implant biological outcome.

Complications of Fixed Full-Arch Implant-Supported Metal-Ceramic Prostheses

We aimed to assess the biological and mechanical-technical complications and survival rate of implants of full-arch metal-ceramic prostheses, during five years of follow-up. 558 implants (of three different brands) retaining 80 full-arch metal-ceramic prostheses were placed in 65 patients, all of whom were examined annually for biological and mechanical-technical complications during the five years of follow-up. Descriptive statistics and univariate logistic regression were calculated. The cumulative survival rate of the implants was 99.8%, and 98.8% prosthesis-based. Mucositis was the most frequent of the biological complications and peri-implantitis was recorded as 13.8% at restoration-level, 16.9% at patient level and 2.0% at implant level. An implant length greater than 10 mm was shown to be a protective factor against biological complications. The mechanical-technical complications were associated with implant diameter, abutment/implant connection and retention system. Loss of screw access filling was the most frequent prosthetic complication, followed by the fracture of the porcelain. Full-arch metal-ceramic prostheses show a high prevalence of implant and prosthesis survival, with few biological and mechanical-technical complications.

Finite element analysis of narrow dental implants

Narrow-diameter implants (NDIs) traditionally have been associated to higher rates of failure in comparison with regular-diameter implants (RDIs) and wide-diameter implants (WDIs), since they generate a more unfavorable stress distribution in peri-implant bone. However, it is well known that the load sharing effect associated with prostheses supported by multiple implants (also called splinted prostheses) affords mechanical benefits. The present study involves finite element analysis (FEA) to determine whether the risks linked to NDIs could be mitigated by the mechanical advantages afforded by the splinting concept. For this purpose, a three-dimensional (3D) model of a real maxilla was reconstructed from computed tomography (CT) images, and different implants (NDIs, RDIs and WDIs) and prostheses were created using computer-aided design (CAD) tools. Biting forces were simulated on the prostheses corresponding to three different rehabilitation solutions: single-implant restoration, three-unit bridge and all-on-four treatment. Stress distribution around the implants was calculated, and overloading in bone was quantified within peri-implant volumes enclosed by cylinders with a diameter 0.1mm greater than that of each implant. The mechanical benefits of the splinting concept were confirmed: the peri-implant overloaded volume around NDIs splinted by means of the three-unit bridge was significantly reduced in comparison with the nonsplinted condition and, most importantly, proved even smaller than that around nonsplinted implants with a larger diameter (RDIs). However, splinted NDIs supporting the all-on-four prosthesis led to the highest risk of overloading found in the study, due to the increase in compressive stress generated around the tilted implant when loading the cantilevered molar.

Stress Distribution on the Prosthetic Screws in the All-on-4 Concept: A Three-Dimensional Finite Element Analysis

The all-on-4 concept, which is used to rehabilitate edentulous patients, can present with mechanical complications such as screw loosening and fracture. The purpose of this study was to evaluate the stress patterns induced in the prosthetic screws by the different prosthetic screw and abutment designs in the all-on-4 concept using finite element analysis. Von Mises stress values on 6 groups of each screw type, including short and narrow screw, short abutment; short and wide screw, short abutment; long and wide screw, short abutment; short and narrow screw, long abutment; short and wide screw, long abutment; and long and wide screw, long abutment, were compared under a cantilever loading of 200 N that was applied on the farther posterior to the position of the connection between the distal implant and the metal framework. Posterior prosthetic screws showed higher stress values than anterior prosthetic screws. The stress values in posterior prosthetic screws decreased as the length and diameter increased. In conclusion, the long and wide screw design offers advantages in stress distribution when compared with the short and narrow design.

Biomechanical effect of implant design on four implants supporting mandibular full-arch fixed dentures: In vitro test and finite element analysis

BACKGROUND/PURPOSE

Impact of the implant shape on the biomechanical performance of all-on-four treatment of dental implant is still unclear. This study evaluated the all-on-four treatment with four osseointegrated implants in terms of the biomechanical effects of implant design and loading position on the implant and surrounding bone by using both in vitro strain gauge tests and three-dimensional (3D) finite element (FE) analyses.

METHODS

Both in vitro and 3D FE models were constructed with placing NobelSpeedy and NobelActive implants as well as a titanium framework in an edentulous jawbone based on the concept of all-on-four treatment. Three types of loads were applied: at the central incisor area (loading position 1) and at the molar regions with (loading position 2) and without (loading position 3) the denture cantilever. For the in vitro tests, the principal bone strains were recorded by rosette strain gauges and statistically evaluated using Wilcoxon's rank-sum test. The 3D FE simulations analyzed the peak von-Mises stresses in the implant and surrounding cortical bone.

RESULTS

The peak stress and strain in the surrounding bone were typically 36-62% (3D FE analysis) and 47-57% (in vitro test) (p < 0.001)higher for loading position 3 than for loading positions 1 and 2. Between those two implant designs, the bone strains and bone stresses did not differ significantly.

CONCLUSION

For all-on-four treatment with four osseointegrated dental implants, altering the implant design does not appear to affect the biomechanical performance of the entire treatment, especially in terms of the stresses and strains in the surrounding bone.

Zirconia crowns cemented on titanium bars using CAD/CAM: a five-year follow-up prospective clinical study of 9 patients

BACKGROUND

The purpose of this prospective clinical study was to evaluate clinical results of the passive fit of the substructure in the Toronto bridge and the chipping or delamination of the ceramic veneering on the zirconia-support, after 5 years, in nine patients rehabilitated with zirconia crowns cemented on titanium bars using CAD/CAM technology.

METHODS

A total of nine healthy patient fully edentulous in the upper and lower jaws with non-contributory past medical anamnesis needing full fixed total prosthesis maxilla and mandible were included in this clinical study, where a total 9 mandibles and 9 jaws were treated. The inclusion criteria in order for a patient to participate in the study were: a signed consent form, fully edentulous in the upper and lower jaws, required a full fixed total prosthesis restoration. The exclusion criteria were age limitation of less than 18 years old, chemotherapy, head and neck radiation therapy, diabetes or periodontal disease, smoking and severe illness. All patients received zirconia crowns cemented on titanium bars using CAD/CAM technology. The primary outcome of this study was to examine the survival rate of the zirconia crowns cemented on titanium bars using CAD/CAM technology during the observation period. Any chipping or delamination of the zirconia crowns of the restorations was considered as failure. The secondary outcome was to evaluate the passive fit of the substructure on the implants, loose of occlusal screws, implant survival and satisfactory occlusion.

RESULTS

In 5 years of follow-up no evidence of chipping or delamination of the ceramic veneering on the zirconia crown supported were observed. Fifteen finished protesis (93.75%) showed satisfactory occlusion and only one case (6.25%) required significant occlusal adjustment. During the first year recall all bars were stable (100%) no mobility of protheses was recorded. After 5 years all bars were stable (100%) and no mobility of protheses was recorded.

CONCLUSION

The computerized workflow for the process of building bar and prosthesis ensures reproducible results and excellent adaptation and passive insertion of them, as well as conditions for avoiding mechanical complications and guarantees stability of screw-implant abutments.

Zygoma Implants or Sinus Lift for the Atrophic Maxilla with a Dentate Mandible: Which is the Better Option?

Rehabilitation of maxillary atrophy with dental implants is challenging to the clinician despite the wide variety of surgical techniques available. Finding the right indication for a procedure is highly important for the long-term stability of dental implants. With the introduction of the concept of "teeth-in-a-day," clinicians have explored innovative techniques to attain the goal of immediate implant-supported provisional prosthesis. However, costs and comorbidities are limitations to advancing these techniques. This article focuses on algorithms to rehabilitate the atrophic maxilla with the purpose of providing immediate provisional prosthetic teeth regardless of the mandibular dentition.

Horizontal augmentation of the maxillary alveolar ridge to change the prosthetic profile: Clinical and radiological results of a retrospective study

BACKGROUND

In this retrospective study, we aimed to analyze the clinical and radiological results of compensating the long-term deficiencies in hard and soft tissues of edentulous patients by placing dental implants and performing a horizontal ridge augmentation.

MATERIAL AND METHODS

We treated patients with edentulous maxillaries (Cawood-Howell type III or IV) by combining 4 implants, or 6 implants, or using zygomatic and conventional anterior implants as appropriate. Simultaneously, horizontal ridge augmentation was performed by combining autologous bone with Bio-Oss and membranes.

RESULTS

A total of 14 zygomatic and 80 standard implants were used for the rehabilitations in 16 edentulous patients. The success rates were 93.75% and 85.71% for the standard and zygomatic implants, respectively. Also, respective gains of 5.79mm and 3.25mm were obtained at the levels of the midsagittal line and canines, with respective resorption rates of 10% and 8.6% after 20months.

CONCLUSION

The millimeters gained by performing a horizontal augmentation optimizes the relation between the implant position and the prosthetic profile. This allows the different prostheses to be selected and for rehabilitation to be optimized. In this way, mucosal coverage can be avoided and fixed prosthetic design can be enhanced.

The Accuracy of Computer-Assisted Implant Surgery Performed Using Fully Guided Templates versus Pilot-Drill Guided Templates

Purpose. Computer-assisted stereolithographically guided surgery allows an ideal implant placement for prosthetic restoration. Two types of stereolithographic templates are currently available: a fully guided template and a pilot-drill guided template. The purpose of this study was (i) to evaluate the accuracy of implant insertion using these types of surgical templates and (ii) to define parameters influencing accuracy. Materials and Methods. 20 patients were enrolled and divided into 2 study groups: in group A, implants were placed using CAD-CAM templates with fully guided sleeves; in group B, implants were placed with a template with only pilot-drill guided sleeves. Pre- and postoperative computed tomographies were used to measure differences between final positions of implants and virtually planned positions. Three linear discrepancies (coronal, apical, and depth) and two angular ones (buccolingual and mesiodistal) were measured. Correlations between accuracy and jaws of interest, implant length and diameters, and type of edentulism were also analysed. Results. A total of 50 implants were inserted in 15 patients using CAD-CAM templates: 23 implants in group A and 27 in group B. The mean coronal deviations were 1.16 and 1.11 mm (P = 0.35), respectively; the mean apical deviations were 1.65 and 1.71 mm (P = 0.22); the mean depth deviations were 0.95 and −0.68 mm (P = 0.032); the mean buccolingual angular deviations were 4.16° and 6.72° (P = 0.042); and the mean mesiodistal ones were 2.81° and 5.61° (P = 0.029). In addition, the accuracy was statistically influenced only by implant diameter for coronal discrepancy (P = 0.035) and by jaw of interest for mesiodistal angulation (P = 0.045). Conclusion. Fully guided implant surgery was more accurate than pilot-drill guided surgery for different parameters. For both types of surgery, a safety margin of at least 2mm should be preserved during implant planning to prevent damage to nearby anatomical structures.