Recent findings in pulsed light disinfection

Pulsed Light Treatment Effect on Color, Oxidative Stability, and Listeria monocytogenes Population of Sliced Mortadella

This study evaluated the effects of high-intensity pulsed light (PL) on sliced mortadella, assessing how the parameters pulse width (1260 to 2520 µs) and number of pulses (one to three) influence color, oxidative stability, and Listeria monocytogenes population. The different PL parameters generated a fluence ranging from 2.64 to 6.57 J/cm2 and irradiance ranging from 1046.9 to 1738.8 W/cm2. The PL slightly increased the temperature and pH of the samples, and this elevation was well correlated to the higher number of pulses and higher fluence. The color parameter a* was reduced while b* values increased after PL application, with these effects being more significant in treatments with a higher number of pulses and higher fluence. The highest values of TBARS were found in treatments with higher fluence (5.28 and 6.57 J/cm2), which were characterized by the attribute "oxidized color" in sensory evaluation. The different PL conditions reduced the count of L. monocytogenes by up to 1.44 Log CFU/cm2. The treatment with a pulse width of 1260 µs, two pulses, fluence of 4.38 J/cm2, and irradiance of 1738.3 W/cm2 achieved the same efficacy in pathogen reduction as the treatments with higher fluence. Moreover, these PL conditions had a minimal impact on the color and oxidative stability of mortadella, demonstrating an effective balance between microbiological safety and quality preservation.

Comparing resistance of bacterial spores and fungal conidia to pulsed light and UVC radiation at a wavelength of 254 nm

Pulsed light (PL) inactivates microorganisms by UV-rich, high-irradiance and short time pulses (250 μs) of white light with wavelengths from 200 nm to 1100 nm. PL is applied for disinfection of food packaging material and food-contact equipment. Spores of seven Bacillus ssp. strains and one Geobacillus stearothermophilus strain and conidia of filamentous fungi (One strain of Aspergillus brasiliensis, A. carbonarius and Penicillium rubens) were submitted to PL (fluence from 0.23 J/cm2 to 4.0 J/cm2) and UVC (at λ = 254 nm; fluence from 0.01 J/cm2 to 3.0 J/cm2). One PL flash at 3 J/cm2 allowed at least 3 log-reduction of all tested microorganisms. The emetic B. cereus strain F4810/72 was the most resistant of the tested spore-forming bacteria. The PL fluence to 3 log-reduction (F3 PL) of its spores suspended in water was 2.9 J/cm2 and F3 UVC was 0.21 J/cm2, higher than F3 PL and F3 UVC of spores of B. pumilus SAFR-032 2.0 J/cm2 and 0.15 J/cm2, respectively), yet reported as a highly UV-resistant spore-forming bacterium. PL and UVC sensitivity of bacterial spores was correlated. Aspergillus spp. conidia suspended in water were poorly sensitive to PL. In contrast, PL inactivated Aspergillus spp. conidia spread on a dry surface more efficiently than UVC. The F2 PL of A. brasiliensis DSM1988 was 0.39 J/cm2 and F2 UVC was 0.83 J/cm2. The resistance of spore-forming bacteria to PL could be reasonably predicted from the knowledge of their UVC resistance. In contrast, the sensitivity of fungal conidia to PL must be specifically explored.

Radical species generating technologies for decontamination of Listeria species in food: a recent review report

Foodborne illnesses occur due to the contamination of fresh, frozen, or processed food products by some pathogens. Among several pathogens responsible for the illnesses, Listeria monocytogenes is one of the lethal bacteria that endangers public health. Several preexisting and novel technologies, especially non-thermal technologies are being studied for their antimicrobial effects, particularly toward L. monocytogenes. Some noteworthy emerging technologies include ultraviolet (UV) or light-emitting diode (LED), pulsed light, cold plasma, and ozonation. These technologies are gaining popularity since no heat is employed and undesirable deterioration of food quality, especially texture, and taste is devoided. This review aims to summarize the most recent advances in non-thermal processing technologies and their effect on inactivating L. monocytogenes in food products and on sanitizing packaging materials. These technologies use varying mechanisms, such as photoinactivation, photosensitization, disruption of bacterial membrane and cytoplasm, etc. This review can help food processing industries select the appropriate processing techniques for optimal benefits, in which the structural integrity of food can be preserved while simultaneously destroying L. monocytogenes present in foods. To eliminate Listeria spp., different technologies possess varying mechanisms such as rupturing the cell wall, formation of pyrimidine dimers in the DNA through photochemical effect, excitation of endogenous porphyrins by photosensitizers, generating reactive species, causing leakage of cellular contents and oxidizing proteins and lipids. These technologies provide an alternative to heat-based sterilization technologies and further development is still required to minimize the drawbacks associated with some technologies.

Recent Insights on the Role of Various Food Processing Operations Towards the Development of Sustainable Food Systems

Chronic hunger and malnutrition will eventually result from the population's rapid growth. It is unlikely to succeed in tackling the rising challenges of delivering sustainable food for all people unless high attention is paid on the function of food processing to ensure the supply of stable food. It is impossible to overstate the importance of developing food processing and preservation technologies that can reduce food losses and wastage during surplus seasons. Therefore, sustainable food systems must be developed to provide healthy diets without damaging our world and its resources. The goal is to use various perspectives to confirm why food processing is crucial to future food supply. It is important to show the appropriate utilization of sustainability factors and effect assessments to construct for feeding the globe while staying within planetary limits. There has never been a better time to assure a plentiful food supply to feed the people than right now, when the population is expanding at a worrying rate. The sustainable food project seeks to move the food systems in a long-term, more equitable direction. Food processing, or the conversion of raw materials into functional, edible, and consumer acceptable food, is a critical link in the food value chain between consumption and production. This review looked at various existing and emerging food processing followed by preservation techniques. Food systems must also attempt to reduce food waste and losses, as well as the current and future impacts on the environment and society, to be sustainable.

Phototreatment (below 1100 nm) improving quality attributes of fresh-cut fruits and vegetables: A review

The emerging area of phototreatment technology has shown a significant potential to enhance the quality of fresh-cut fruit and vegetable products (FFVP). This review critically evaluates relevant literatures to address the potential for phototreatment technology (Red, blue, green, ultraviolet and pulsed light) applied to FFVP, outline the key to the success of phototreatment processing, and discuss the corresponding problems for phototreatment processing along with research and development needs. Base on photothermal, photophysical and photochemical process, phototreatment displays a great potential to maintain quality attributes of FFVP. The operating parameters of light, the surface properties and matrix components of the targeted material and the equipment design affect the quality of the fresh-cut products. To adapt current phototreatment technology to industrial FFVP processing, it is necessary to offset some limitations, especially control of harmful substances (For example, nitrite and furan) produced by phototreatment, comparison between different phototreatment technologies, and establishment of mathematical models/databases.

Positive biofilms to guide surface microbial ecology in livestock buildings

The increase in human consumption of animal proteins implies changes in the management of meat production. This is followed by increasingly restrictive regulations on antimicrobial products such as chemical biocides and antibiotics, used in particular to control pathogens that can spread zoonotic diseases. Aligned with the One Health concept, alternative biological solutions are under development and are starting to be used in animal production. Beneficial bacteria able to form positive biofilms and guide surface microbial ecology to limit microbial pathogen settlement are promising tools that could complement existing biosecurity practices to maintain the hygiene of livestock buildings. Although the benefits of positive biofilms have already been documented, the associated fundamental mechanisms and the rationale of the microbial composition of these new products are still sparce. This review provides an overview of the envisioned modes of action of positive biofilms used on livestock building surfaces and the resulting criteria for the selection of the appropriate microorganisms for this specific application. Limits and advantages of this biosecurity approach are discussed as well as the impact of such practices along the food chain, from farm to fork.

Advances in prepared dish processing using efficient physical fields: A review

Prepared dishes are increasingly popular convenience food that can be eaten directly from hygienic packaging by heating. Physics field (PF) is food processing method built with physical processing technology, which has the characteristics of high efficiency and environmental safety. This review focuses on summarizing the application of PFs in prepared dishes, evaluating and comparing PFs through quality changes during processing and storage of prepared dishes. Currently, improving the quality and extending the shelf life of prepared dishes through thermal and non-thermal processing are the main modes of action of PFs. Most PFs show good potential in handing prepared dishes, but may also react poorly to some prepared dishes. In addition, the difficulty of precise control of processing conditions has led to research mostly at the laboratory stage, but as physical technology continues to break through, more PFs and multi-physical field will be promoted for commercial use in the future. This review contributes to a deeper understanding of the effect of PFs on prepared dishes, and provides theoretical reference and practical basis for future processing research in the development of various enhanced PFs.

Pulsed Light Application for Campylobacter Control on Poultry Meat and Its Effect on Colour and Volatile Profile

Campylobacter on poultry meat needs to be controlled to reduce the risk of infection caused by the consumption of chicken meat. Pulsed light (PL) application on poultry meat was studied to control Campylobacter spp. The effect of this technology was evaluated regarding poultry meat colour and volatile compound changes. Two breast sample groups were prepared: inoculated with Campylobacter (107 bacteria of Campylobacter jejuni strains) and not inoculated. Samples were submitted to PL, five pulses/s of 300 ms, 1 Hz, and 1 J/cm2 in the apparatus, PL Tecum unit (Claranor). A response surface experimental design was applied regarding the factors of voltage (1828 to 3000 W) and distance to the source UV lamp (2.6 to 5.4 cm). The binomial factorial treatment (voltage and distance) with PL induced different energy doses (fluence J/cm2) received by samples, 2.82 to 9.67 J/cm2. Poultry meat pulsed light treated had a significant decrease of Enterobacteriaceae counts. The treatments applied were unable to reduce 1 log Campylobacter cfu/g of poultry meat. The poultry meat PL treated became slightly light, redder, and yellower than those not treated. PL can decrease the proportion of aldehydes on total volatiles in meat, particularly on those associated with chicken-like, chicken skin-like, and sweet odour notes in fresh poultry meat. Further studies of PL with higher energy doses will be necessary to confirm if there are Campylobacter reductions and about poultry meat treated under storage to evaluate if volatile compounds can affect the flavour of PL-treated meat samples.

Lifestyle of Listeria monocytogenes and food safety: Emerging listericidal technologies in the food industry

Listeria monocytogenes, a causative agent of listeriosis, is a major foodborne pathogen. Among pathogens, L. monocytogenes stands out for its unique ecological and physiological characteristics. This distinct lifestyle of L. monocytogenes has a significant impact on food safety and public health, mainly through the ability of this pathogen to multiply at refrigeration temperature and to persist in the food processing environment. Due to a combination of these characteristics and emerging trends in consumer preference for ready-to-eat and minimally processed food, there is a need to develop effective and sustainable approaches to control contamination of food products with L. monocytogenes. Implementation of an efficient and reliable control strategy for L. monocytogenes must first address the problem of cross-contamination. Besides the preventive control strategies, cross-contamination may be addressed with the introduction of emerging post packaging non-thermal or thermal hurdles that can ensure delivery of a listericidal step in a packed product without interfering with the organoleptic characteristics of a food product. This review aims to present the most relevant findings underlying the distinct lifestyle of L. monocytogenes and its impact on food safety. We also discuss emerging food decontamination technologies that can be used to better control L. monocytogenes.

Effect of ultraviolet light treatment on microbiological safety and quality of fresh produce: An overview

Fresh and fresh-cut fruits and vegetables have been associated in several foodborne illness outbreaks. Although investigations from those outbreaks reported that the contamination with pathogenic microorganisms may occur at any point in the farm to fork continuum, effective control strategies are still being widely investigated. In that direction, the concept of hurdle technology involving a sequence of different interventions have been widely explored. Among those interventions, ultraviolet (UV) light alone or in combination with other treatments such as use of organic acids or sanitizer solutions, has found to be a promising approach to maintain the microbiological safety and quality of fresh and fresh-cut produce. Recent advances in using UV as a part of hurdle technology on the safety of fresh produce at different stages are presented here. Furthermore, this review discusses the mechanism of UV induced antimicrobial activity, factors that influence antimicrobial efficacy and its effect on produce. In addition, the challenges, and prospects of using UV irradiation as an intervention treatment were also discussed.

Current insights into non-thermal preservation technologies alternative to conventional high-temperature short-time pasteurization of drinking milk

Milk is an important nutritional food source characterized by a perishable nature and conventionally thermally treated to guarantee its safety. In recent years, an increasing focus on competing non-thermal food processing technologies has been driven mainly by consumers' expectations for minimally processed products. Due to the heat sensitivity of milk, much research interest has been addressed to mild non-thermal pasteurization processing to keep safety, 'fresh-like' taste and to maintain the organoleptic qualities of raw milk. This review provides an overview of the current literature on non-thermal treatments as standalone alternative technologies to high-temperature short-time (HTST) pasteurization of drinking milk. Results of lab-scale experimentations suggest the feasibility of most emerging non-thermal processing technologies, including high hydrostatic pressure, pulsed electric field, cold plasma, cavitation and light-based technologies, as alternative to thermal treatment of drinking milk with premium in shelf life duration. Nevertheless, a series of regulatory, technological and economical hurdles hinder the industrial scaling-up for most of these substitutes. To date, only high hydrostatic pressure treatments are applied as alone alternative to HTSH pasteurization for processing of "cold pasteurized" drinking milk. Milk submitted to HTST treatment combined to ultraviolet light is currently accepted in EU countries as novel food.

Mild processing of seafood-A review

Recent years have shown a tremendous increase in consumer demands for healthy, natural, high-quality convenience foods, especially within the fish and seafood sector. Traditional processing technologies such as drying or extensive heating can cause deterioration of nutrients and sensory quality uncompilable with these demands. This has led to development of many novel processing technologies, which include several mild technologies. The present review highlights the potential of mild thermal, and nonthermal physical, and chemical technologies, either used alone or in combination, to obtain safe seafood products with good shelf life and preference among consumers. Moreover, applications and limitations are discussed to provide a clear view of the potential for future development and applications. Some of the reviewed technologies, or combinations thereof, have shown great potential for non-seafood products, yet data are missing for fish and seafood in general. The present paper visualizes these knowledge gaps and the potential for new technology developments in the seafood sector. Among identified gaps, the combination of mild heating (e.g., sous vide or microwave) with more novel technologies such as pulsed electric field, pulsed light, soluble gas stabilization, cold plasma, or Ohmic heat must be highlighted. However, before industrial applications are available, more research is needed.

Postharvest Treatment of Chinese Kale (Brassica oleracea var. alboglabra) by Pulse Light to Removal of Microbial Load, Pesticide Residue and Integrity of Physicochemical Quality and Phytochemical Constituent

Existence of microorganisms, pesticide residue on fresh vegetables has a potential hazard to human health. The demand for safe green Chinese kale (Brassica oleracea var. alboglabra) has increased recently. Chinese kale is a healthy botanical attached to the Brassicaceae class. It contains numerous nutritional and phytochemical constituents beneficial for human health. Besides health benefits, this green vegetable also poses food safety concerns due to pathogen and pesticide residue during cultivation. Non-thermal physical technology like pulsed light (PL) will be a promising alternative to eradicate microbial and pesticide residue while preserving the best physicochemical properties and phytochemical components. This research evaluated the influence of different pulsed light intensities (1.2-10.8 J/cm2) on the removal of microbial load and pesticide residue as well as weight attrition, texture hardness, dry matter, vitamin C, total phenolic content in the treated Chinese kale. Results showed that pulsed light intensity 8.4 J/cm2 was appropriate to completely eliminate pathogenic bacteria such as Escherichia coli, Staphylococcus aureus, Salmonella; pesticide substances such as carbendazim, abamectin, cypermethrin, chlorpyrifos ethyl, mancozeb. At pulsed light intensity 8.4 J/cm2, weight attrition in the treated sample was lower than weight attrition in the untreated; meanwhile textural hardness, dry matter, ascorbic acid and total phenolic content remained higher in the treated sample compared to the untreated. The results reveals that the pulsed light technique should be applied as a promising decontamination approach for removal of the pathogen as well as pesticide residue with minor impact on physicochemical properties and phytochemical constituents.

Pulsed Light (PL) Treatments on Almond Kernels: Salmonella enteritidis Inactivation Kinetics and Infrared Thermography Insights

Abstract

Extending the shelf-life and ensuring microbiological safety of food products while preserving the nutritional properties are key aspects that must be addressed. Heat processing of food matrices has been the golden standard during the last decades, while certain non-thermal processing options have recently gained ground. In the present study, experimental pulsed light (PL) surface inactivation treatments of Salmonella enteritidis on almonds kernels are performed. The PL system is set to test different operative conditions, namely power (1000, 1250, and 1500 W) and frequency (1.8, 3.0, and 100.0 Hz) at different treatment times (from 5 to 250 s), which result in applied fluence doses in the 0–100 J·cm⁻² range. Additionally, temperature measurements are collected at each operative condition on the almond surface (using infrared (IR) thermography) and at the superficial layer of the almond (1-mm depth using a thermocouple). The observed PL inactivation kinetics are then modelled using four different models. The best goodness-of-fit is found for the two-parameter Weibull model (R² > 0.98 and RMSE < 0.33 for all cases). The maximum achieved log-CFU reductions are 6.02 for the 1.8-Hz system, 4.69 for the 3.0-Hz system, and 3.66 for 100.0-Hz system. The offset between the collected temperature readings by the two sensors is contrasted against the inactivation rate (following the two-parameter Weibull model). It was found that the highest inactivation rate corresponds approximately to the point where the infrared camera detects a slowdown in the surface heating.

Graphical Abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s11947-021-02725-9.

A comprehensive review on impact of non-thermal processing on the structural changes of food components

Non-thermal food processing is a viable alternative to traditional thermal processing to meet customer needs for high-quality, convenient and minimally processed foods. They are designed to eliminate elevated temperatures during processing and avoid the adverse effects of heat on food products. Numerous thermal and novel non-thermal technologies influence food structure at the micro and macroscopic levels. They affect several properties such as rheology, flavour, process stability, texture, and appearance at microscopic and macroscopic levels. This review presents existing knowledge and advances on the impact of non-thermal technologies, for instance, cold plasma treatment, irradiation, high-pressure processing, ultrasonication, pulsed light technology, high voltage electric field and pulsed electric field treatment on the structural changes of food components. An extensive review of the literature indicates that different non-thermal processing technologies can affect the food components, which significantly affects the structure of food. Applications of novel non-thermal technologies have shown considerable impact on food structure by altering protein structures via free radicals or larger or smaller molecules. Lipid oxidation is another process responsible for undesirable effects in food when treated with non-thermal techniques. Non-thermal technologies may also affect starch properties, reduce molecular weight, and change the starch granule's surface. Such modification of food structure could create novel food textures, enhance sensory properties, improve digestibility, improve water-binding ability and improve mediation of gelation processes. However, it is challenging to determine these technologies' influence on food components due to differences in their primary operation and equipment design mechanisms and different operating conditions. Hence, to get the most value from non-thermal technologies, more in-depth research about their effect on various food components is required.

Apple Juice Preservation Using Combined Nonthermal Processing and Antimicrobial Packaging

ABSTRACT

This study was conducted to investigate the effectiveness of pulsed electric fields (PEFs), pulsed UV light (PL), and antimicrobial packaging (AP), either individually or combined, for inactivating bacteria and maintaining the quality of fruit juices. Apple juice samples were inoculated with Escherichia coli K-12 or native molds and yeasts (M&Y), treated with bench-scale PEF and/or PL processing systems, and stored in glass jars with antimicrobial caps containing 10 μL of carvacrol. The reductions in microbial populations and the physicochemical properties of juice samples were determined after treatments and during storage at 10°C. The treatments were PL (5 to 50 s at 1.04 J/cm2/s), PEF (19, 23, and 30 kV/cm), PEF followed by PL (PEF+PL), PL followed by PEF (PL+PEF), and PEF+PL+AP. PEF treatments at 19 to 30 kV/cm (PEF19, PEF23, and PEF30) resulted in 2.0-, 2.6-, and 4.0-log reductions of E. coli, respectively, and PL treatments for 10 to 50 s (PL10, PL20, PL30, PL40, and PL50) resulted in 0.45-, 0.67-, 0.76-, 2.3-, and 4.0-log reductions, respectively. No significant differences (P > 0.05) were found between the combined PL20+PEF19 and PEF19+PL20 treatments; both treatments reduced E. coli K-12 populations to nondetectable levels (>5-log reductions) after 7 days. Both PEF+PL and PEF+PL+AP treatments achieved >5-log reductions of M&Y; however, juice samples subjected to PEF+PL+AP treatment had lower M&Y counts (2.9 log units) than did samples subjected to PEF+PL treatment (3.9 log units) after 7 days. No significant differences (P > 0.05) in pH, acidity, and total soluble solids were found among all samples after treatments. Increased PL treatment times reduced color a* and b* values, total phenolics, and carotenoids. This study provides information valuable to juice processors for consideration and design of nonthermal pasteurization of juice products.

HIGHLIGHTS

Improvement of Must Fermentation from Late Harvest cv. Tempranillo Grapes Treated with Pulsed Light

Pulsed light irradiation is a nonthermal technology currently used for the elimination of pathogens from a diverse range of food products. In the last two decades, the results obtained using PL at laboratory scale are encouraging wine experts to use it in the winemaking industry. PL can reduce native yeast counts significantly, which facilitates the use of starter cultures, reducing SO2 requirements at the same time. In this experimental set up, Tempranillo grapes were subjected to pulsed light treatment, and the fermentative performance of non-Saccharomyces yeasts belonging to the species Schizosaccharomyces pombe, Lachancea thermotolerans, Torulaspora delbrueckii, Metschnikowia pulcherrima and Hanseniaspora vineae was monitored in sequential fermentations against spontaneous fermentation and pure culture fermentation with the species Saccharomyces cerevisiae. The experimental analyses comprised the determination of anthocyanin (High performance liquid chromatography with photodiode array detector-HPLC-DAD), polyphenol index and colour (Ultraviolet-visible spectroscopy-UV-Vis spectrophotometer), fermentation-derived volatiles (Gas chromatography with flame ionization detector-GC-FID), oenological parameters (Fourier transform Infrared spectroscopy-FT-IR) and structural damage of the skin (atomic force microscopy-AFM). The results showed a decrease of 1.2 log CFU/mL yeast counts after pulsed light treatment and more rapid and controlled fermentation kinetics in musts from treated grapes than in untreated samples. The fermentations done with treated grapes allowed starter cultures to better implant in the must, although a larger anthocyanin loss (up to 93%) and an increase in hue values (1 unit) towards more yellow hues were observed for treated grapes. The development of biomass was larger in musts from treated grapes. The profile of volatile compounds and oenological parameters reveals that fermentations carried out with untreated grapes are prone to deviations from native microbiota (e.g., production of lactic acid). Finally, no severe damage on the skin was observed with the AFM on treated grapes.

Physical and Chemical Methods for Reduction in Aflatoxin Content of Feed and Food

Aflatoxins (AFs) are among the most harmful fungal secondary metabolites imposing serious health risks on both household animals and humans. The more frequent occurrence of aflatoxins in the feed and food chain is clearly foreseeable as a consequence of the extreme weather conditions recorded most recently worldwide. Furthermore, production parameters, such as unadjusted variety use and improper cultural practices, can also increase the incidence of contamination. In current aflatoxin control measures, emphasis is put on prevention including a plethora of pre-harvest methods, introduced to control Aspergillus infestations and to avoid the deleterious effects of aflatoxins on public health. Nevertheless, the continuous evaluation and improvement of post-harvest methods to combat these hazardous secondary metabolites are also required. Already in-use and emerging physical methods, such as pulsed electric fields and other nonthermal treatments as well as interventions with chemical agents such as acids, enzymes, gases, and absorbents in animal husbandry have been demonstrated as effective in reducing mycotoxins in feed and food. Although most of them have no disadvantageous effect either on nutritional properties or food safety, further research is needed to ensure the expected efficacy. Nevertheless, we can envisage the rapid spread of these easy-to-use, cost-effective, and safe post-harvest tools during storage and food processing.

Physical Methods for the Decontamination of Meat Surfaces

Purpose of Review

The market for minimally processed products is constantly growing due to consumer demand. Besides food safety and increased shelf life, nutritional value and sensory appearance also play a major role and have to be considered by the food processors. Therefore, the purpose of the review was to summarize recent knowledge about important alternative non-thermal physical technologies, including both those which are actually applied (e.g. high-pressure processing and irradiation) and those demonstrating a high potential for future application in raw meat decontamination (e.g. pulsed light UV-C and cold plasma treatment). The evaluation of the methods is carried out with respect to efficiency, preservation of food quality and consumer acceptance.

Recent Findings

It was evident that significantly higher bacterial reductions are achieved with gamma-ray, electron beam irradiation and high pressure, followed by pulsed light, UV-C and cold plasma, with ultrasound alone proving the least effective. As a limitation, it must be noted that sensory deviations may occur and that legal approvals may have to be applied for.

Summary

In summary, it can be concluded that physical methods have the potential to be used for decontamination of meat surfaces in addition to common hygiene measures. However, the aim of future research should be more focused on the combined use of different technologies to further increase the inactivation effects by keeping meat quality at the same time.

Identification of Quinone Degradation as a Triggering Event for Intense Pulsed Light-Elicited Metabolic Changes in Escherichia coli by Metabolomic Fingerprinting

Intense pulsed light (IPL) is becoming a new technical platform for disinfecting food against pathogenic bacteria. Metabolic changes are deemed to occur in bacteria as either the causes or the consequences of IPL-elicited bactericidal and bacteriostatic effects. However, little is known about the influences of IPL on bacterial metabolome. In this study, the IPL treatment was applied to E. coli K-12 for 0–20 s, leading to time- and dose-dependent reductions in colony-forming units (CFU) and morphological changes. Both membrane lipids and cytoplasmic metabolites of the control and IPL-treated E. coli were examined by the liquid chromatography-mass spectrometry (LC-MS)-based metabolomic fingerprinting. The results from multivariate modeling and marker identification indicate that the metabolites in electron transport chain (ETC), redox response, glycolysis, amino acid, and nucleotide metabolism were selectively affected by the IPL treatments. The time courses and scales of these metabolic changes, together with the biochemical connections among them, revealed a cascade of events that might be initiated by the degradation of quinone electron carriers and then followed by oxidative stress, disruption of intermediary metabolism, nucleotide degradation, and morphological changes. Therefore, the degradations of membrane quinones, especially the rapid depletion of menaquinone-8 (MK-8), can be considered as a triggering event in the IPL-elicited metabolic changes in E. coli.

The spore coat is essential for Bacillus subtilis spore resistance to pulsed light, and pulsed light treatment eliminates some spore coat proteins

Microbial surface contamination of equipment or of food contact material is a recurring problem in the food industry. Spore-forming bacteria are far more resistant to a wide variety of treatments than their vegetative forms. Understanding the mechanisms underlying decontamination processes is needed to improve surface decontamination strategies against endospores potentially at the source of foodborne diseases or food-spoilage. Pulsed light (PL) with xenon lamps delivers high-energy short-time pulses of light with wavelengths in the range 200 nm-1100 nm and a high UV-C fraction. Bacillus subtilis spores were exposed to either PL or to continuous UV-C. Gel electrophoresis and western blotting revealed elimination of various proteins of the spore coat, an essential outer structure that protects spores from a wide variety of environmental conditions and inactivation treatments. Proteomic analysis confirmed the elimination of some spore coat proteins after PL treatment. Transmission electron microscopy of PL treated spores revealed a gap between the lamellar inner spore coat and the outer spore coat. Overall, spores of mutant strains with defects in genes coding for spore coat proteins were more sensitive to PL than to continuous UV-C. This study demonstrates that radiations delivered by PL contribute to specific damage to the spore coat, and overall to spore inactivation.

Microbes associated with fresh produce: Sources, types and methods to reduce spoilage and contamination

Global food security remains one of the most important challenges that needs to be addressed to ensure the increasing demand for food of the fast growing human population is satisfied. Fruits and vegetables comprise an essential component of a healthy balanced diet as they are the major source of both macro- and micronutrients. They are particularly important for communities in developing countries whose nutrition often relies solely on a plant-based diet. Recent advances in agriculture and food processing technologies have facilitated production of fresh, nutritious and safe food for consumers. However, despite the development of sophisticated chemical and physical methods of food and equipment disinfection, fresh-cut produce and fruit juice industry still faces significant economic losses due to microbial spoilage. Furthermore, fresh produce remains an important source of pathogens that have been causing outbreaks of human illness worldwide. This chapter characterizes common spoilage and human pathogenic microorganisms associated with fresh-cut produce and fruit juice products, and discusses the methods and technology that have been developed and utilized over the years to combat them. Substantial attention is given to highlight advantages and disadvantages of using these methods to reduce microbial spoilage and their efficacy to eliminate human pathogenic microbes associated with consumption of fresh-cut produce and fruit juice products.

Bactericidal effect of intense pulsed light on seeds without loss of viability

This study investigated the microbial inactivation effects of intense pulsed light (IPL) treatment as an alternative to chemical treatment for decontaminating the radish and pak choi seeds. The f R values (which indicate the resistance to IPL treatment) for radish and pak choi seeds were 24.50, 20.81 J/cm2, respectively. This resistance exhibited by seeds to IPL treatment is related to their surface roughness. Their Rq (the root-mean-square roughness), average surface roughness (Ra), and 10-point height roughness (Rz) values indicate that each crevice on a rough surface could shelter microorganisms from IPL. Viability tests of seeds exposed to IPL treatment indicated that the average germination rates of treated seeds exceeded 85% on day 3 of germination, which is considered as an acceptable criterion for germination. Also, on day 5 of germination the average shoot lengths of sprouts exposed to IPL did not differ significantly from those of untreated seeds.

Key role of singlet oxygen and peroxynitrite in viral RNA damage during virucidal effect of plasma torch on feline calicivirus

A dielectric barrier discharge (DBD) plasma torch has been used to evaluate the mechanism underlying inactivation of feline calicivirus (FCV) by plasma treatment. Plasma treatment of cell lysate infected with FCV F9 strain reduced the viral titer of the median tissue culture infectious dose (TCID₅₀). The D value (treatment time required to lower the viral titer to 1/10) was 0.450 min, while the viral titer dropped below the detection limit within 2 min. FCV was not significantly inactivated by heat or UV applied at levels corresponding to those generated from the DBD plasma torch after 2 min (38.4 °C and 46.79 mJ/cm² UV, respectively). However, TCID₅₀ was reduced by 2.47 log after exposure to 4.62 mM ONOO⁻, corresponding to the concentration generated after 2 min of plasma treatment. Radical scavengers, including superoxide dismutase, dimethyl sulfoxide, and catalase, did not significantly affect viral titers; however, sodium azide, uric acid, and ascorbic acid, which are scavengers of ¹O₂ radicals, ONOO⁻, and peroxynitrous acid (ONOOH; produced from ONOO⁻ under acidic conditions), respectively, significantly increased TCID₅₀ and intact viral RNA. These findings suggest that ONOO⁻ and ¹O₂ play an important role in FCV inactivation by attacking viral RNA during DBD plasma torch treatment.

Sublethal Injury and Viable but Non-culturable (VBNC) State in Microorganisms During Preservation of Food and Biological Materials by Non-thermal Processes

The viable but non-culturable (VBNC) state, as well as sublethal injury of microorganisms pose a distinct threat to food safety, as the use of traditional, culture-based microbiological analyses might lead to an underestimation or a misinterpretation of the product's microbial status and recovery phenomena of microorganisms may occur. For thermal treatments, a large amount of data and experience is available and processes are designed accordingly. In case of innovative inactivation treatments, however, there are still several open points with relevance for the investigation of inactivation mechanisms as well as for the application and validation of the preservation processes. Thus, this paper presents a comprehensive compilation of non-thermal preservation technologies, i.e., high hydrostatic pressure (HHP), pulsed electric fields (PEFs), pulsed light (PL), and ultraviolet (UV) radiation, as well as cold plasma (CP) treatments. The basic technological principles and the cellular and molecular mechanisms of action are described. Based on this, appropriate analytical methods are outlined, i.e., direct viable count, staining, and molecular biological methods, in order to enable the differentiation between viable and dead cells, as well as the possible occurrence of an intermediate state. Finally, further research needs are outlined.