Method measuring oxygen tension and transport within subcutaneous devices

Effect of Cell Density of a Methacrylic Acid-Based Hydrogel Implant on Embedded Islet Function and Viability

Subcutaneous delivery of islets in a methacrylic acid-based hydrogel may offer a functional cure for type 1 diabetes. Here we show in mice that the hydrogel is able to provide sufficient vasculature to support islet function and viability, when islets are used at a low islet volume fraction (i.e., cell density). The Krogh cylinder model was used to mathematically estimate the effect of implant volume, for a fixed islet dose (600 islet equivalents [IEQ]), on the minimum vessel density required to maintain sufficient pO2 within the graft. Modeling suggested that 200 μL implants would have low enough islet densities and enough vessels to have islets remain viable, but that 50 μL implants would not; this was confirmed experimentally through measurement of glucose level in streptozotocin-induced diabetic severe combined immunodeficiency disease (SCID/bg) mice, comparing 200 and 50 μL implants, both with 600 IEQ. Vessel densities were ∼20-30 vessels/mm2 independent of implant volume and vessels were sufficient to increase subcutaneous oxygen tension, as measured with microcapsules containing oxygen sensitive material (a platinum [Pt] porphyrin); both these results were determined without cells. These results are useful in thinking about the scale-up of this system to humans: to maintain a low islet density (∼0.5%), many more islets will require attention to the subcutaneous implant configuration to satisfy the oxygen needs of the cells.

The Optimal Maturation of Subcutaneous Pouch Can Improve Pancreatic Islets Engraftment in Rat Model

BACKGROUND

Transplantation of pancreatic islets into subcutaneous cavities in diabetic rats may be as or even more effective than transplantation into the portal vein. Identifying the optimal timing of the individual steps in this procedure is critical.

METHODS

Macroporous scaffolds were placed in the subcutaneous tissue of diabetic male Lewis rats for 7 or 28 d and the healing of the tissue inside the scaffolds was monitored. A marginal syngeneic graft comprising 4 islets/g of recipient body weight was transplanted at the best timing focusing mainly on vascularization. Recipients were monitored for blood glucose levels and tolerance tests. Histological examination was performed in all implanted scaffolds. The presence of individual endocrine cells was analyzed in detail.

RESULTS

Blood glucose levels remained within the physiological range in all recipients until the end of experiment as well as body weight increase. Coefficients of glucose assimilation were normal or slightly reduced with no statistically significant differences between the groups 40 and 80 d after transplantation. Histological analysis revealed round viable islets in the liver similar to those in pancreas, but alpha cells practically disappeared, whereas islets in the scaffolds formed clusters of cells surrounded by rich vascular network and the alpha cells remained partially preserved.

CONCLUSIONS

Subcutaneous transplantation of pancreatic islets is considerably less invasive but comparably efficient as commonly used islet transplantation into the portal vein. In consideration of alpha and beta cell ratio, the artificial subcutaneous cavities represent a promising site for future islet transplantation therapy.

A therapeutic convection-enhanced macroencapsulation device for enhancing β cell viability and insulin secretion

Islet transplantation for type 1 diabetes treatment has been limited by the need for lifelong immunosuppression regimens. This challenge has prompted the development of macroencapsulation devices (MEDs) to immunoprotect the transplanted islets. While promising, conventional MEDs are faced with insufficient transport of oxygen, glucose, and insulin because of the reliance on passive diffusion. Hence, these devices are constrained to two-dimensional, wafer-like geometries with limited loading capacity to maintain cells within a distance of passive diffusion. We hypothesized that convective nutrient transport could extend the loading capacity while also promoting cell viability, rapid glucose equilibration, and the physiological levels of insulin secretion. Here, we showed that convective transport improves nutrient delivery throughout the device and affords a three-dimensional capsule geometry that encapsulates 9.7-fold-more cells than conventional MEDs. Transplantation of a convection-enhanced MED (ceMED) containing insulin-secreting β cells into immunocompetent, hyperglycemic rats demonstrated a rapid, vascular-independent, and glucose-stimulated insulin response, resulting in early amelioration of hyperglycemia, improved glucose tolerance, and reduced fibrosis. Finally, to address potential translational barriers, we outlined future steps necessary to optimize the ceMED design for long-term efficacy and clinical utility.

Non-Invasive Monitoring of Oxygen Tension and Oxygen Transport Inside Subcutaneous Devices After H2S Treatment

Medical devices for cell therapy can be improved through prevascularization. In this work we study the vascularization of a porous polymer device, previously used by our group for pancreatic islet transplantation with results indicating improved glycemic control. Oxygen partial pressure within such devices was monitored non-invasively using an optical technique. Oxygen-sensitive tubes were fabricated and placed inside devices prior to subcutaneous implantation in nude mice. We tested the hypothesis that vascularization will be enhanced by administration of the pro-angiogenic factor hydrogen sulfide (H2S). We found that oxygen dynamics were unique to each implant and that the administration of H2S does not result in significant changes in perfusion of the devices as compared with control. These observations suggest that vascular perfusion and density are not necessarily correlated, and that the rate of vascularization was not enhanced by the pro-angiogenic agent.

New approach to measuring oxygen diffusion and consumption in encapsulated living cells, based on electron spin resonance microscopy

Cell microencapsulation within biocompatible polymers is an established technology for immobilizing living cells that secrete therapeutic products.  These can be transplanted into a desired site in the body for the controlled and continuous delivery of the therapeutic molecules.  One of the most important properties of the material that makes up the microcapsule is its oxygen penetrability, which is critical for the cells' survival.  Oxygen reaches the cells inside the microcapsules via a diffusion process.  The diffusion coefficient for the microcapsules' gel material is commonly measured using bulk techniques, where the gel in a chamber is first flushed with nitrogen and the subsequent rate of oxygen diffusion back into it is measured by an oxygen electrode placed in the chamber.  This technique does not address possible heterogeneities between microcapsules, and also cannot reveal O₂ heterogeneity inside the microcapsule resulting from the living cells' activity.  Here we develop and demonstrate a proof of principle for a new approach to measuring and imaging the partial pressure of oxygen (pO₂) inside a single microcapsule by means of high-resolution and high-sensitivity electron spin resonance (ESR).  The proposed methodology makes use of biocompatible paramagnetic microparticulates intercalated inside the microcapsule during its preparation.  The new ESR approach was used to measure the O₂ diffusion properties of two types of gel materials (alginate and extracellular matrix - ECM), as well as to map a 3D image of the oxygen inside single microcapsules with living cells. STATEMENT OF SIGNIFICANCE: The technology of cell microencapsulation offers major advantages in the sustained delivery of therapeutic agents used for the treatment of various diseases ranging from diabetes to cancer. Despite the great advances made in this field, it still faces substantial challenges, preventing it from reaching the clinical practice. One of the primary challenges in developing cell microencapsulation systems is providing the cells with adequate supply of oxygen in the long term. Nevertheless, there is still no methodology good enough for measuring O2 distribution inside the microcapsule with sufficient accuracy and spatial resolution without affecting the microcapsule and/or the cells' activity in it. In the present work, we introduce a novel magnetic resonance technique to address O2 availability within cell-entrapping microcapsules. For the first time O2 distribution can be accurately measured and imaged within a single microcapsule. This new technique may be an efficient tool in the development of more optimal microencapsulation systems in the future, thus bringing this promising field closer to clinical application.

Mathematical predictions of oxygen availability in micro- and macro-encapsulated human and porcine pancreatic islets

Optimal function of immunoisolated islets requires adequate supply of oxygen to metabolically active insulin producing beta-cells. Using mathematical modeling, we investigated the influence of the pO₂ on islet insulin secretory capacity and evaluated conditions that could lead to the development of tissue anoxia, modeled for a 300 μm islet in a 500 μm microcapsule or a 500 μm planar, slab-shaped macrocapsule. The pO₂ was used to assess the part of islets that contributed to insulin secretion. Assuming a 500 μm macrocapsule with a 300 μm islet, with oxygen consumption rate (OCR) of 100-300 nmol min^-1 mg^-1 DNA, islets did not develop any necrotic core. The nonfunctional zone (with no insulin secretion if pO₂  < 0.1 mmHg) was 0.3% for human islets (OCR ~100 nmol/min/mg DNA) and 35% for porcine islets (OCR ~300 nmol/min/mg DNA). The OCR of the islet preparation is profoundly affected by islet size, with optimal size of <250 μm in diameter (human) or <150 μm (porcine). Our data suggest that microcapsules afford superior oxygen delivery to encapsulated islets than macrocapsules, and optimal islet function can be achieved by encapsulating multiple, small (<150 μm) islets with OCR of ~100 nmol min^-1 mg^-1 DNA (human islets) or ~200 nmol min^-1 mg^-1 DNA (porcine islets).

Defining Physiological Normoxia for Improved Translation of Cell Physiology to Animal Models and Humans

The extensive oxygen gradient between the air we breathe (Po₂ ~21 kPa) and its ultimate distribution within mitochondria (as low as ~0.5-1 kPa) is testament to the efforts expended in limiting its inherent toxicity. It has long been recognized that cell culture undertaken under room air conditions falls short of replicating this protection in vitro. Despite this, difficulty in accurately determining the appropriate O₂ levels in which to culture cells, coupled with a lack of the technology to replicate and maintain a physiological O₂ environment in vitro, has hindered addressing this issue thus far. In this review, we aim to address the current understanding of tissue Po₂ distribution in vivo and summarize the attempts made to replicate these conditions in vitro. The state-of-the-art techniques employed to accurately determine O₂ levels, as well as the issues associated with reproducing physiological O₂ levels in vitro, are also critically reviewed. We aim to provide the framework for researchers to undertake cell culture under O₂ levels relevant to specific tissues and organs. We envisage that this review will facilitate a paradigm shift, enabling translation of findings under physiological conditions in vitro to disease pathology and the design of novel therapeutics.

The emerging field of pancreatic tissue engineering: A systematic review and evidence map of scaffold materials and scaffolding techniques for insulin-secreting cells

A bioartificial endocrine pancreas is proposed as a future alternative to current treatment options. Patients with insulin-secretion deficiency might benefit. This is the first systematic review that provides an overview of scaffold materials and techniques for insulin-secreting cells or cells to be differentiated into insulin-secreting cells. An electronic literature survey was conducted in PubMed/MEDLINE and Web of Science, limited to the past 10 years. A total of 197 articles investigating 60 different materials met the inclusion criteria. The extracted data on materials, cell types, study design, and transplantation sites were plotted into two evidence gap maps. Integral parts of the tissue engineering network such as fabrication technique, extracellular matrix, vascularization, immunoprotection, suitable transplantation sites, and the use of stem cells are highlighted. This systematic review provides an evidence-based structure for future studies. Accumulating evidence shows that scaffold-based tissue engineering can enhance the viability and function or differentiation of insulin-secreting cells both in vitro and in vivo.

Design of Bioartificial Pancreases From the Standpoint of Oxygen Supply

A bioartificial pancreas (BAP), in which islets of Langerhans (islets) are enclosed in a semipermeable membrane, has been developed to realize islet transplantation without the use of immunosuppressive drugs. Although recent progress in induced pluripotent stem (iPS) and embryonic stem (ES) cells has attracted attention owing to the potential applications of these cells as insulin-releasing cells, concerns about the safety of implantation of these cells remain. The use of the BAP has the advantage of easy removal if insulin-releasing cells derived from iPS/ES cells undesirably proliferate and form tumors in the BAP. Oxygen supply is a crucial issue for cell survival in BAPs as insufficient oxygen supply causes central necrosis of cell aggregates. In this study, we derived several simple equations considering oxygen supply in BAPs in order to provide insights into the rational design of three different types of BAPs (spherical microcapsules, cylindrical capsules, and planar capsules). The equations give (i) the thickness of a capsule membrane leading to no central necrosis of encapsulated cell aggregates as a function of the original size of the cell aggregate; (ii) the oxygen concentration profiles in BAPs; (iii) the effects of encapsulation of a cell aggregate on insulin release; (iv) the amount of encapsulated cells required to normalize blood glucose levels of a patient; and (v) the total volumes and sizes of BAPs. As an example, we used the equations in order to design three different types of BAPs for subcutaneous implantation.

Selection of Implantation Sites for Transplantation of Encapsulated Pancreatic Islets

Pancreatic islet transplantation has been validated as a valuable therapy for type 1 diabetes mellitus patients with exhausted insulin treatment. However, this therapy remains limited by the shortage of donor and the requirement of lifelong immunosuppression. Islet encapsulation, as an available bioartificial pancreas (BAP), represents a promising approach to enable protecting islet grafts without or with minimal immunosuppression and possibly expanding the donor pool. To develop a clinically implantable BAP, some key aspects need to be taken into account: encapsulation material, capsule design, and implant site. Among them, the implant site exerts an important influence on the engraftment, stability, and biocompatibility of implanted BAP. Currently, an optimal site for encapsulated islet transplantation may include sufficient capacity to host large graft volumes, portal drainage, ease of access using safe and reproducible procedure, adequate blood/oxygen supply, minimal immune/inflammatory reaction, pliable for noninvasive imaging and biopsy, and potential of local microenvironment manipulation or bioengineering. Varying degrees of success have been confirmed with the utilization of liver or extrahepatic sites in an experimental or preclinical setting. However, the ideal implant site remains to be further engineered or selected for the widespread application of encapsulated islet transplantation.

Stimulation of vascularization of a subcutaneous scaffold applicable for pancreatic islet-transplantation enhances immediate post-transplant islet graft function but not long-term normoglycemia

The liver as transplantation site for pancreatic islets is associated with significant loss of islets, which can be prevented by grafting in a prevascularized, subcutaneous scaffold. Supporting vascularization of a scaffold to limit the period of ischemia is challenging and was developed here by applying liposomes for controlled release of angiogenic factors. The angiogenic capacity of platelet-derived growth factor, vascular endothelial growth factor, acidic fibroblast growth factor (aFGF), and basic FGF were compared in a tube formation assay. Furthermore, the release kinetics of different liposome compositions were tested. aFGF and L-α-phosphatidylcholine/cholesterol liposomes were selected to support vascularization. Two dosages of aFGF-liposomes (0.5 and 1.0 μg aFGF per injection) were administered weekly for a month after which islets were transplanted. We observed enhanced efficacy in the immediate post-transplant period compared to the untreated scaffolds. However, on the long-term, glucose levels of the aFGF treated animals started to increase to diabetic levels. These results suggest that injections with aFGF liposomes do improve vascularization and the immediate restoration of blood glucose levels but does not facilitate the long-term survival of islets. Our data emphasize the need for long-term studies to evaluate potential beneficial and adverse effects of vascularization protocols of scaffolds. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 2533-2542, 2017.

Facile Formation of Redox-Active Totally Organic Nanoparticles in Water by In Situ Reduction of Organic Precursors Stabilized through Aromatic-Aromatic Interactions by Aromatic Polyelectrolytes

The formation of redox-active, totally organic nanoparticles in water is achieved following a strategy similar to that used to form metal nanoparticles. It is based on two fundamental concepts: i) complexation through aromatic-aromatic interactions of a water-soluble precursor aromatic molecule with polyelectrolytes bearing complementary charged aromatic rings, and ii) reduction of the precursor molecule to achieve stabilized nanoparticles. Thus, formazan nanoparticles are synthesized by reduction of a tetrazolium salt with ascorbic acid using polyelectrolytes bearing benzene sulfonate residues of high linear aromatic density, but cannot be formed in the presence of nonaromatic polyelectrolytes. The red colored nanoparticles are efficiently encapsulated in calcium alginate beads, showing macroscopic homogeneity. Bleaching kinetics with chlorine show linear rates on the order of tenths of milli-meters per minute. A linear behavior of the dependence of the rate of bleaching on the chlorine concentration is found, showing the potential of the nanoparticles for chlorine sensing.