Occurrence of surface active agents in the environment

Oxidative treatment of micropollutants present in wastewater: A special emphasis on transformation products, their toxicity, detection, and field-scale investigations

Micropollutants have become ubiquitous in aqueous environments due to the increased use of pharmaceuticals, personal care products, pesticides, and other compounds. In this review, the removal of micropollutants from aqueous matrices using various advanced oxidation processes (AOPs), such as photocatalysis, electrocatalysis, sulfate radical-based AOPs, ozonation, and Fenton-based processes has been comprehensively discussed. Most of the compounds were successfully degraded with an efficiency of more than 90%, resulting in the formation of transformation products (TPs). In this respect, degradation pathways with multiple mechanisms, including decarboxylation, hydroxylation, and halogenation, have been illustrated. Various techniques for the analysis of micropollutants and their TPs have been discussed. Additionally, the ecotoxicity posed by these TPs was determined using the toxicity estimation software tool (T.E.S.T.). Finally, the performance and cost-effectiveness of the AOPs at the pilot scale have been reviewed. The current review will help in understanding the treatment efficacy of different AOPs, degradation pathways, and ecotoxicity of TPs so formed.

Removal of anionic surfactant from aqueous solutions by adsorption onto biochars: characterisation, kinetics, and mechanism

Biochar, a waste biomass-derived adsorbent, holds promise for decentralised wastewater treatment. However, limited research exists on its efficacy in adsorbing anionic surfactants in wastewater. To address this, the adsorption of sodium dodecyl sulphate (SDS), a common anionic surfactant, was studied using various biochar types: rice husk biochar (RH-550 and RH-700), wheat straw biochar (WS-550 and WS-700) produced at 550°C and 700°C, wood-based biochar (OB), and activated carbon (AC) as a control. The study investigated the impact of pH (3-9), adsorbent loading (1-10 g/L), adsorbent size (<0.5-2.5 mm), contact time (5-180 min), and initial concentration (50-200 mg/L) on SDS removal. Under optimised conditions (100 mg/L SDS, 4 g/L adsorbent, 1-2 mm particle size, pH 8.3, and 180 min contact time), maximum SDS removals were RH-550 (78%), RH-700 (82.4%), WS-550 (89.5%), WS-700 (90.4%), AC (97%), and OB (88.4%). Among the tested adsorbent materials, WS-550 exhibited the highest SDS adsorption capacity at 66.23 mg/g compared to AC (80.65 mg/g), followed by RH-550 (49.75 mg/g), OB (45.87 mg/g), RH-700 (43.67 mg/g), and WS-700 (42.74 mg/g). SDS adsorption followed a pseudo-second-order kinetic model, indicating chemisorption on the adsorbent surface. The Freundlich isotherm model exhibited a better fit for the experimental data on SDS adsorption using all tested adsorbents except for RH-550. This study showed that biochars produced from agricultural and forestry residues are effective adsorbents for SDS in aqueous solutions and can be a promising sustainable and low-cost material for the treatment of greywater containing anionic surfactants (e.g. handwashing, laundry, kitchen, and bathroom greywaters).

Impact of the Naturally Driven Surfactant in EOR Application: Experimental, Microscopic, and Numerical Analyses

While synthetic, conventional surfactants have a known negative environmental impact, their high cost poses a significant challenge. In contrast, naturally extracted surfactants are cheaper and are readily available. The applicability of natural surfactants depends on the saponin concentration, extraction, and synthesis methods. Certain parameters, such as their efficiency in obtaining the required interfacial tension (IFT) values, salinity tolerance, and stability under reservoir conditions, must be examined. Kazakhstan produces a substantial quantity of flaxseed, and flaxseed oil is a good source of fatty acids that can be converted to natural surfactants. Therefore, the work aims to identify the potential of the natural-flaxseed oil surfactant. The experimental study evaluated the synthesized surfactant, effective concentration, salinity's effect, interfacial tension, rheology, and oil recovery concerns in vugs limestone. A microscopic study was conducted to provide insight into the flow in the vugus matrix. At the same time, the numerical method was also employed to establish a potential recovery understanding. The Fourier spectrometer results proved the distinct presence of the triterpenoid. The critical micelle concentrations are 6 and 2.5 wt % for solution in 0 and seawater salinity, respectively. The IFT was reduced by 40-48% and is more effective in seawater solutions. The oil additional recovery was 39-50% after surfactants. The presence of a fractured vugus did not affect the success of the application. Despite the difficulty in modeling the system, the numerical results agree with the experiments and show only 7% differences in total recovery. The research offers novel natural surfactants that can be applied in offshore Kazakhstan.

Surfactant-Mediated Effects on Hydrological and Physical Soil Properties: Data Synthesis

Soils are under the threat of a multitude of anthropogenic factors affecting the complex interplay of various physical and hydrological soil processes and properties. One such factor is the group of surface-active compounds. Surfactants have a broad range of applications and can reduce solid-liquid interfacial forces and increase wettability and dispersion of particles. Surfactant effects are context-dependent, giving rise to a wide range of reported effects on different soil processes and properties. Here, we evaluate the evidence base of surfactant research on 11 hydrological and physical soil variables. Our goal was to identify knowledge gaps and test the robustness of the proposed surfactant effects. We found that the current knowledge base is insufficient to reach strong data-backed conclusions about the effects of surfactants in soils. We identified a unique case of bias in the data as a result of conflated patterns from laboratory and field studies. We could not support the hypothesis that the surfactant charge determines soil effects for any of the tested soil variables. We believe that further experiments on surfactant-mediated effects on soil properties and processes are urgently required, paying attention, in particular, to improving experimental design and data reporting standards.

Surfactants in water and wastewater (greywater): Environmental toxicity and treatment options

Surfactant, an emerging pollutant present in greywater, raises the toxicity levels in the water body. Soap, detergent, and personal care items add surfactant to greywater. Due to excessive washing and cleaning procedures brought on by the COVID-19 pandemic, the release of surfactants in greywater has also increased. Considering the environmental toxicity and problems it creates during the treatment, it's essential to remove surfactants from the wastewater. This review intends to explain and address the environmental toxicity of the surfactant released via greywater and current techniques for surfactant removal from wastewater. Various physical, chemical, and biological methods are reported. Modern adsorbents such as hydrophilic silica nanoparticles, chitosan, fly ash, and iron oxide remove surfactants by adsorption. Membrane filtration effectively removes surfactants but is not cost-effective. Coagulants (chemical and natural coagulants) neutralize surfactant charges and help remove them as bigger particles. Electrocoagulation/electroflotation causes surfactants to coagulate and float. Microorganisms break down surfactants in microbial fuel cells to generate power. Surfactants are removed by natural processes and plants in constructed wetlands where traditional aerobic and anaerobic approaches use microbes to break down surfactants. Constructed wetlands, natural coagulation-flocculation, and microbial fuel cells are environmentally beneficial methods to remove surfactants from wastewater.

Nanostructured Lipid Carriers Enriched Hydrogels for Skin Topical Administration of Quercetin and Omega-3 Fatty Acid

Chronic skin exposure to external hostile agents (e.g., UV radiation, microorganisms, and oxidizing chemicals) may increase oxidative stress, causing skin damage and aging. Because of their well-known skincare and protective benefits, quercetin (Q) and omega-3 fatty acids (ω3) have attracted the attention of the dermocosmetic and pharmaceutical sectors. However, both bioactives have inherent properties that limit their efficient skin delivery. Therefore, nanostructured lipid carriers (NLCs) and enriched PFC® hydrogels (HGs) have been developed as a dual-approach vehicle for Q and/or ω3 skin topical administration to improve bioactives' stability and skin permeation. Two NLC formulations were prepared with the same lipid composition but differing in surfactant composition (NLC1-soy lecithin and poloxamer 407; NLC2-Tween® 80 and dioctyl sodium sulfosuccinate (DOSS)), which have an impact on physicochemical properties and pharmaceutical and therapeutic performance. Despite both NLCs presenting high Q loading capacity, NLC2's physicochemical properties make them more suitable for topical skin administration and ensure longer colloidal stability. Additionally, NLC2 demonstrated a more sustained Q release, indicating higher bioactive storage while improving permeability. The occlusive effect of NLCs-enriched HGs also has a positive impact on skin permeability. Q-loaded NLC2, with or without ω3, -enriched HGs demonstrated efficacy as antioxidant and photoprotective formulations as well as effective reduction in S. aureus growth, indicating that they constitute a promising approach for topical skin administration to prevent skin aging and other damaging cutaneous processes.

Rhamnolipid Self-Aggregation in Aqueous Media: A Long Journey toward the Definition of Structure–Property Relationships

The need to protect human and environmental health and avoid the widespread use of substances obtained from nonrenewable sources is steering research toward the discovery and development of new molecules characterized by high biocompatibility and biodegradability. Due to their very widespread use, a class of substances for which this need is particularly urgent is that of surfactants. In this respect, an attractive and promising alternative to commonly used synthetic surfactants is represented by so-called biosurfactants, amphiphiles naturally derived from microorganisms. One of the best-known families of biosurfactants is that of rhamnolipids, which are glycolipids with a headgroup formed by one or two rhamnose units. Great scientific and technological effort has been devoted to optimization of their production processes, as well as their physicochemical characterization. However, a conclusive structure–function relationship is far from being defined. In this review, we aim to move a step forward in this direction, by presenting a comprehensive and unified discussion of physicochemical properties of rhamnolipids as a function of solution conditions and rhamnolipid structure. We also discuss still unresolved issues that deserve further investigation in the future, to allow the replacement of conventional surfactants with rhamnolipids.

Bacterial-derived surfactants: an update on general aspects and forthcoming applications

The search for sustainable alternatives to the production of chemicals using renewable substrates and natural processes has been widely encouraged. Microbial surfactants or biosurfactants are surface-active compounds synthesized by fungi, yeasts, and bacteria. Due to their great metabolic versatility, bacteria are the most traditional and well-known microbial surfactant producers, being Bacillus and Pseudomonas species their typical representatives. To be successfully applied in industry, surfactants need to maintain stability under the harsh environmental conditions present in manufacturing processes; thus, the prospection of biosurfactants derived from extremophiles is a promising strategy to the discovery of novel and useful molecules. Bacterial surfactants show interesting properties suitable for a range of applications in the oil industry, food, agriculture, pharmaceuticals, cosmetics, bioremediation, and more recently, nanotechnology. In addition, they can be synthesized using renewable resources as substrates, contributing to the circular economy and sustainability. The article presents a general and updated review of bacterial-derived biosurfactants, focusing on the potential of some groups that are still underexploited, as well as, recent trends and contributions of these versatile biomolecules to circular bioeconomy and nanotechnology.

Formation mechanisms and mechanical properties of anaerobic lagoon scum

The formation of a floating scum layer on the liquid surface of covered anaerobic lagoons prevents optimal and efficient lagoon operation. Scum can reduce hydraulic retention time, inhibit biogas capture and cause damage to lagoon covers. Managing the negative impact of scum requires understanding what scum is, how it forms and how it consolidates. This paper presents measurements of the physical and mechanical properties of scum and sludge samples from two covered anaerobic lagoons that alternatively treat municipal and abattoir waste. Both scum samples consisted of a large proportion of suspended solids that sank once the sample was diluted, degassed and mixed, indicating that sludge flotation and buoyancy due to biogas generation is a major contributor to scum accumulation. Total and soluble chemical oxygen demand and volatile solids in the scum are approximately 90 % higher than in sludge, which indicates that scum has a large proportion of undigested solids. Fourier-transform infrared spectroscopy demonstrates that scum and sludge have similar organic matter, with both including fats, oils, greases, proteins, and polysaccharides. Scum formation due to gas buoyancy implies that scum accumulation is inevitable and controlling fats, oils, and greases at the source of the wastewater is not enough to stop scum formation. Scum accumulation increases due to buoyancy, which drives scum compaction and increases the strength of the scum, as demonstrated by the measurement of scum compressional rheology. Scum management techniques that disturb the scum layer early enough to release the entrapped gas enable the scum to sink and get digested, thus minimising the impact of scum formation.

An overview on surfactants as pollutants of concern: Occurrence, impacts and persulfate-based remediation technologies

Surfactants are molecules that reduce interfacial energy and increase solubility of other pollutants in water. These properties make them suitable for various domestic and industrial applications, soil remediation, pesticide formulation, among others. The increase in their use and the lack of strict regulations regarding their disposal and management is a matter of concern and requires more attention since the release and distribution of these compounds into the environment can modify important water quality parameters. As a result of these changes, different toxicological effects to aquatic organisms are discussed and exposed herein. On this basis, we provide an overview of the classes of surfactants, as well as their occurrence in different aqueous matrices. In addition, existing regulations around the world regarding their concentration limit for different environments are discussed. Current research focuses on the application of conventional treatments, such as biological treatments; notwithstanding, more toxic and bioaccumulative products can be generated. Advanced Oxidation Processes are promising alternatives and have also been widely applied for the removal of surfactants. This study provides, for the first time, an overview of the application of persulfate-based processes for surfactants degradation based on recent literature findings, as well as the various factors related to the activation of the persulfate anions. This review also highlights the challenges and opportunities for future research to overcome the obstacles to the practical application of this process.

Surfactant Pollution, an Emerging Threat to Ecosystem: Approaches for Effective Bacterial Degradation

The use of surfactants in households and industries is inevitable and so is their discharge into the environment, especially into the water bodies as effluents. Being surface-active agents, their utilization is mostly seen in soaps, detergents, personal care products, emulsifiers, wetting agents, etc. Anionic surfactants are the most used class. These surfactants are responsible for the foam and froth in the water bodies and cause potential adverse effects to both biotic and abiotic components of the ecosystem. Surfactants are capable of penetrating the cell membrane and thus cause toxicity to living organisms. Accumulation of these compounds has been known to cause significant gill damage and loss of sight in fish. Alteration of physiological and biochemical parameters of water decreases the amount of dissolved oxygen and thus affecting the entire ecosystem. Microbes utilizing surfactants as substrates for energy form the basis of the biodegradation of these compounds. The main organisms for surfactant biodegradation, both in sewage and natural waters, are bacteria. Several Pseudomonas and Bacillus spp. have shown efficient degradation of anionic surfactants namely: sodium dodecyl sulphate (SDS), linear alkylbenzene sulphonate (LAS), sodium dodecylbenzenesulphonate (SDBS). Also, several microbial consortia constituting Alcaligenes spp., Citrobacter spp., etc. have shown efficacy in the degradation of surfactants. The biodegradation efficiency studies of these microbes/microbial consortia would be of immense help in formulating better solutions for the bioremediation of surfactants and help to reduce their potential environmental hazards.

A Simplified Method for Anionic Surfactant Analysis in Water Using a New Solvent

Anionic surfactants (AS) are becoming a major emerging contaminant of waters due to their widespread use in household and industrial products. The standard chloroform method for analysis of AS in water relies on chloroform extraction of a methylene blue active substance (MBAS), which contains ion pairs between methylene blue (MB) molecules (positively charged) and AS. Due to the poor extractability of chloroform, the procedure is complicated, time-consuming, and subject to anionic interferences. A mixture of methyl isobutyl ketone (MIBK)–1,2-dichloroethane (DCE) at a 3:1 ratio of MIBK:DCE proved to be a robust solvent for AS extraction for a wide range of samples under various chemical conditions. The objectives of this research were to set the washing protocol to eliminate the anionic interferences in the MIBK-DCE extraction and to develop a new simplified analytical method for AS analysis using the MIBK-DCE (3:1) extractant. The suitability of the proposed MIBK-DCE method was validated based on quality control and assurance criteria, such as selectivity, accuracy, precision, method detection limit (MDL), limit of quantification (LOQ), and sensitivity. Various water samples, such as freshwater, wastewater, and seawater, were used for the method development and validation. Interferences by inorganic and organic anions were evident in the reference chloroform method but were eliminated in the MIBK-DCE procedure with a two-step process that consisted of washing with a carbonate/bicarbonate solution at pH 9.2 and a mixture of silver sulfate (Ag₂SO₄) and potassium alum (AlK(SO₄)₂). The simplified MIBK-DCE method for sodium dodecyl sulfate (SDS) analysis consisted of (i) sample pre-treatment, (ii) MIBK-DCE extraction, (iii) washing and filtration, and (iv) absorbance measurement. The MIBK-DCE method was accurate, precise, selective, and sensitive for AS analysis and showed MDL of 0.0001 mg/L, LOQ of 0.0005 mg/L, relative standard deviation (RSD) of 0.1%, and recovery of 99.0%. All these criteria were superior to those of the chloroform method. Sensitivity analysis showed highly significant correlations in AS analyses between the MIBK-DCE and chloroform methods for domestic wastewater, industrial wastewater, and seawater. The MIBK-DCE method is simple, rapid, robust, reproducible, and convenient, when compared to the chloroform method. Results demonstrate that the simplified MIBK-DCE method can be employed for AS analysis in a wide range of environmental waters including seawater.

Anionic surfactants monitoring in healthcare facilities - a case of Belo Horizonte City, Brazil

Surfactants are substances that when in aquatic environments can cause negative impacts. Hospital effluents carry numerous chemicals daily, including surfactants, used in sanitization and disinfection procedures. These chemicals are found in the effluents and reach water bodies due to a lack of proper removal in the wastewater treatment plants. The present study investigated data about wastewater monitored from healthcare facilities located in the city of Belo Horizonte, Brazil, focusing on anionic surfactants. The results showed 72 establishments monitoring this parameter, resulting in a median concentration of 1 mg L^-1 and 2.49 mg L^-1 mean value of anionic surfactants, between 2007 and 2019. It is also observed in the correlation between surfactants and oils in all healthcare establishment sizes, except for the medium-sized. Although anionic surfactants are the most used in cleaning product formulations, cationic surfactants still do not have specific legislation in the studied country that dictates a limit for discharge into sewage; consequently, they are not routinely monitored in effluents. However, these compounds are used in the formulation of routine hospital products.

Assessment on the distributions and exchange of anionic surfactants in the coastal environment of Peninsular Malaysia: A review

Terrestrial anionic surfactants (AS) enter the marine environment through coastal region. Despite that, in general limited knowledge is available on the coastal AS transfer pathway. This paper aims to assess the distributions and exchange of AS in the Peninsular Malaysia coastal environments, adjacent to the southern waters of South China Sea and Strait of Malacca. An assessment case study was conducted by a review on the available data from the workgroup that span between the year 2008 and 2019. The findings showed that AS dominated in the sea surface microlayer (SML, 57%) compared to subsurface water (SSW, 43 %). AS were also found to have dominated in fine mode (FM, 71 %) compared to coarse mode (CM, 29 %) atmospheric aerosols. SML AS correspond to the SSW AS (p < 0.01); however, highest enrichment factor (EF) of the SML AS was not consistent with highest SSW AS. Direct AS exchange between SML and FM and CM was not observed. Furthermore, the paper concludes AS mainly located in the SML and FM and could potentially be the main transfer pathway in the coastal environment.

Environmental impact of increased soap consumption during COVID-19 pandemic: Biodegradable soap production and sustainable packaging

A year into the coronavirus disease 2019 pandemic, the role of washing hands with soap and hand disinfectants is unavoidable as a primary way to control the infection spread in communities and healthcare facilities. The extraordinary surge in demand for handwashing products has led to environmental concerns. Since soaps are complex mixtures of toxic and persistent active ingredients, the prudent option is to promote eco-friendly replacements for the current products. On the other hand, with the increase in soap packaging waste production, soap packaging waste management and recycling become essential to reduce environmental impact. This systematic review aimed to collect some recent methods for identifying biodegradable and sustainable raw materials to produce and package cleaning agents, especially soap.

Environmental risks and toxicity of surfactants: overview of analysis, assessment, and remediation techniques

This work comprehensively reviewed the toxicity and risks of various surfactants and their degraded products in the environmental matrices, various analytical procedures, and remediation methods for these surfactants. The findings revealed that the elevated concentration of surfactants and their degraded products disrupt microbial dynamics and their important biogeochemical processes, hinder plant-surviving processes and their ecological niche, and retard the human organic and systemic functionalities. The enormous adverse effects of surfactants on health and the environment necessitate the need to develop, select, and advance the various analytical and assessment techniques to achieve effective identification and quantification of several surfactants in different environmental matrices. Considering the presence of surfactants in trace concentration and environmental matrices, excellent analysis can only be achieved with appropriate extraction, purification, and preconcentration. Despite these pre-treatment procedures, the chromatographic technique is the preferred analytical technique considering its advancement and shortcomings of other techniques. In the literature, the choice or selection of remediation techniques for surfactants depends largely on eco-friendliness, cost-implications, energy requirements, regeneration potential, and generated sludge composition and volume. Hence, the applications of foam fractionation, electrochemical advanced oxidation processes, thermophilic aerobic membranes reactors, and advanced adsorbents are impressive in the clean-up of the surfactants in the environment. This article presents a compendium of knowledge on environmental toxicity and risks, analytical techniques, and remediation methods of surfactants as a guide for policymakers and researchers.

The influence of salinity on sodium lauryl sulfate toxicity in Mytilus galloprovincialis

The influence of salinity on the effects of sodium lauryl sulfate (SLS) was evaluated using the Mediterranean mussel Mytilus galloprovincialis, exposed for 28 days to SLS (control-0.0 and 4.0 mg/L) under three salinity levels (Control-30, 25 and 35). The effects were monitored using biomarkers related to metabolism and energy reserves, defence mechanisms (antioxidant and biotransformation enzymes) and cellular damage. The results revealed that non-contaminated mussels tended to maintain their metabolic capacity regardless of salinity, without activation of antioxidant defence strategies. On the contrary, although contaminated mussels presented decreased metabolic capacity at salinities 25 and 35, they were able to activate their antioxidant mechanisms, preventing cellular damage. Overall, the present findings indicate that SLS, especially under stressful salinity levels, might potentially jeopardize population survival and reproduction success since reduced metabolism and alterations on mussels' antioxidant mechanisms will impair their biochemical and, consequently, physiological performance.

Nanobioremediation: A sustainable approach towards the degradation of sodium dodecyl sulfate in the environment and simulated conditions

Nanotechnology has gained huge importance in the field of environmental clean-up today. Due to their remarkable and unique properties, it has shown potential application for the remediation of several pesticides and textile dyes. Recently it has shown positive results for the remediation of sodium dodecyl sulfate (SDS). One of the highly exploited surfactants in detergent preparation is anionic surfactants. The SDS selected for the present study is an example of anionic linear alkyl sulfate. It is utilized extensively in industrial washing, which results in the high effluent level of this contaminant and ubiquitously toxic to the environment. The present review is based on the research depicting the adverse effects of SDS in general and possible strategies to minimizing its effects by bacterial degradation which are capable of exploiting the SDS as an only source of carbon. Moreover, it has also highlighted that how nanotechnology can play a role in the remediation of such recalcitrant pesticides.

Protective Effect of Sodium Selenite on 4-Nonylphenol-Induced Hepatotoxicity and Nephrotoxicity in Rats

This study was aimed at evaluating the protective effect of sodium selenite (SS) on DNA integrity, antioxidant/oxidant status, and histological changes on 4-nonylphenol (4-NP)-induced toxicity in liver and kidney tissues of rats. Twenty-four adult male Sprague Dawley rats were divided into 4 groups as control, SS, 4-NP, and SS+4-NP group. Control group was untreated. The SS group was supplemented with SS (0.5 mg/kg/day) and the 4-NP group was given 4-NP (125 mg/kg/day). The rats in the SS+4-NP group received SS followed by 4-NP 1 h later at the abovementioned doses. The treatments were administered by oral gavage for 48 days. DNA damage was analyzed by comet assay in lymphocytes. Oxidative stress parameters were measured, and histological evaluation was performed in liver and kidney tissues. Results showed that SS administration significantly decreased % Tail DNA and Mean Tail Moment in SS+4-NP group as compared with 4-NP group. Catalase activity in liver was significantly lower in 4-NP group only. SS treatment significantly increased the glutathione level and decreased high malondialdehyde level in tissues of the SS+4-NP group as compared with 4-NP group. Dilation of central vein, ballooning degeneration, vacuolar degeneration, and deterioration in the structure of remark cords in 4-NP-administered were alleviated in rats that received SS supplementation before administration of 4-NP. Moreover, glycogen intensity in hepatocytes and the wall of central vein increased in the SS+4-NP group. In addition, the SS supplementation in the SS+4-NP group decreased glomerular degeneration as well as the width of cavum glomeruli and congestion intensity in the kidney. These results indicate that SS may have a protective effect against 4-NP-induced hepato-nephrotoxicity in rats.

The possible role of the surface active substances (SAS) in the airborne transmission of SARS-CoV-2

Surface active substances (SAS) have the potential to form films at different interfaces, consequently influencing the interfacial properties of atmospheric particulate matter (PM). They can be derived from both human activities and natural processes and can be found in an indoor and outdoor environment. This paper's fundamental question is the possible role of the SAS in stabilizing respiratory aerosols in the closed space. In that context, we discuss results of preliminary measurements of the SAS and dissolved organic carbon (DOC) concentrations in the water-soluble fractions of PM_2.5 and PM₁₀ that were sampled simultaneously in primary school inside and outside of the building. The concentrations of SAS were determined using highly sensitive electrochemical measurements. It was observed that SAS and DOC concentrations have been enhanced indoor in both PM fractions. Consistent with these results, a discussion arises on the possibility that SAS could play a crucial role in respiratory droplet dispersion as stabilizers, especially in a closed space. At the same time, we assume that they could prolong the lifetime of respiratory aerosols and as well viability of some (possible SARS-CoV-2) virus inside of the droplets.

Alcohol ethoxysulfates (AES) in environmental matrices

Extensive use of surfactants in numerous fields resulted in their discharge into various environmental compartments including soil, sediment, and water. Alcohol ethoxysulfates (AES) together with alcohol ethoxylates (AE), alkyl sulfates (AS), and linear alkyl benzene sulfonates (LAS) find wide variety of applications in consumer products including both domestic and industrial applications. Consequently, all these surfactants pose several concerns to both aquatic and human health. In the context of environmental impacts, AES has almost equal importance as that of LAS though the literature on this topic is only emerging. This review provides a detailed overview on the various aspects of the anionic surfactant, AES, such as toxicity of AES, its fate in the ecosystem, technical advancements in the area of identification and quantification, its occurrence and distribution in different environmental compartments spanning across the world, and finally a remark of its potential removal strategy from the environment.

Oxidative stress in benthic oligochaete worm, Tubifex tubifex induced by sublethal exposure to a cationic surfactant cetylpyridinium chloride and an anionic surfactant sodium dodecyl sulfate

The present study was assessed to determine the in vivo toxic effects of a cationic surfactant, cetylpyridinium chloride (CPC), and an anionic surfactant, sodium dodecyl sulfate (SDS) in terms of oxidative stress biomarkers in benthic oligochaete worm Tubifex tubifex for 14 days. The investigation demonstrated that sublethal concentrations of CPC (0.0213, and 0.0639 mg L^-1) and SDS (1.094 and 3.092 mg L^-1)induced paramount alterations in the oxidative stress enzymes in Tubifex tubifex. Superoxide dismutase (SOD), glutathione S-transferase (GST), reduced glutathione (GSH), and glutathione peroxidase (GPx) exhibited an initial notable increase in their activities in the surfactants exposed worms at 1d and 7d of exposure period followed by consequential reduction at 14d exposure period with respect to control, while catalase (CAT) and malondialdehyde (MDA) activities markedly incremented gradually throughout the exposure periods. Through the construction of the correlation matrix and integrated biomarker response (IBR), the effects of CPC and SDS on Tubifex tubifex were distinguished. These results indicate that exposure to these cationic and anionic surfactants modulates the levels of oxidative stress enzymes in Tubifex tubifex.

Snowpack-stored atmospheric surface-active contaminants traced with snowmelt water surface film rheology

The aim of the study was to quantify the adsorptive and thermo-elastic properties of snowmelt water surface films and their spatial-temporal evolution with snowpack structure characteristics and the entrapped surface-active organic composition. Surface pressure-area (π-A)T isotherms, surface pressure-temperature (π-T)A isochors, and stress-relaxation (π-t) measurements were performed using a Langmuir trough system on snowmelt water samples collected in a large-scale field studies performed at several industrialized and rural Tricity (Gdansk, Poland) areas at various environmental conditions and subsequent stages of the snowpack melting progress. Since the snow-melted water composition and concentrations of surface active organic matter fractions therein are largely undetermined, the force-area isotherm scaling formalisms (2D virial equation and 2D film scaling theory of polymeric films) were adapted to the complex mixture of surfactants. The surface film parameters and their spatial and temporal evolution turned out to be unequivocally related to principal signatures of the film-forming materials: surfactant concentrations (π, Alim), surface activity (Eisoth, |E|), film material solubility (R), surface material miscibility and 2D architecture complexity (y, βs), molecular thermal mobility (πk), and a timescale of the relaxation processes within the film (τi, |E|). Moreover, the parameters appeared to be correlated with snowpack structure characteristics (snow density ρ, specific snow area SSA, snow cover thickness), sample age time, and anthropogenic atmospheric contamination pressure source locations. In particular, Eisoth was found to be related to ρ and SSA, while R correlated with the solubility of film-forming organics which turned out to be long-chain fatty acids; similarly, spatial profiles of Eisoth revealed the peak values next to the areas being under a severe anthropogenic air pollution pressure. Snowmelt water films stand for a structurally heterogeneous (y > 10) interfacial system where several transition processes of differentiated time-scales (relaxation times from 7 to 63 s) took place leading to the apparent surface viscoelasticity. To sum up, the established surface rheological parameters could serve as novel indicators, based solely on physical attributes, allowing to follow the snowpack evolution, and its melting polymorphism in order to test or improve the existing snow-entrapped organics release models based on chemical analyses. The cross-correlation functional dependences of practical value remain to be established on the larger data set.

Effect of synthetic surfactants on the environment and the potential for substitution by biosurfactants

The environmental impacts of the use of synthetic surfactants are discussed in this work such as their high levels of toxicity and low biodegradability. These materials destroy aquatic microbial populations, damage fish and other aquatic life, and reduce photochemical energy conversion efficiency of plants as well as adversely affecting waste-water treatment processes. With global usage of surfactants being over 15 million tonnes annually, and an estimated 60% of surfactant ending up in the aquatic environment, there is an urgent need for alternatives with lower adverse environmental effects; this review explores biosurfactants as potential alternatives. The sources and natural function of biosurfactants are presented, together with their advantages compared with their synthetic counterparts, including their low toxicity and biodegradability. Their comparable effectiveness as surfactants has been demonstrated by surface tension reduction, achieved at much lower critical micelle concentrations that those of synthetic surfactants. The limitations and challenges for the use of biosurfactants are discussed, particularly low production yields; such limitations must be addressed before wide range industrial use of biosurfactants can be achieved. Although there has been focus on achieving greater production yields, a remaining issue is the lack of research into the use of biosurfactants in a greater range of industrial and consumer applications to demonstrate their efficacy and identify candidate biosurfactants for production. This review highlights such research as deserving of further investigation, alongside the ongoing work to optimize the production process.

Surface Activity of Natural Surfactants Extracted from Sapindus mukorossi and Sapindus trifoliatus Soapnuts

Surfactants derived from renewable sources such as plants are an ecological alternative to synthetic surfactants. Aqueous solutions of natural surfactants extracted from soapnuts obtained from two plants, Sapindus mukorossi and Sapindus trifoliatus, were studied. Their properties in terms of surface tension reduction and wettability were examinated. The natural surfactants show the ability to reduce the surface tension and increase the wettability of the hydrophobic polytetrafluoroethylene surface. These nuts can be used repeatedly for washing also in hard water. Crude extracts from Sp. trifoliatus exhibit better surface properties than those from Sp. mukorossi. This makes these soapnuts a good potential source of biosurfactants for household use.

Biosurfactant inducers for enhanced production of surfactin and rhamnolipids: an overview

Biosurfactants can be widely used in industries as pharmaceutical agents, for microbial enhanced oil recovery, crop biostimulation, among others. Surfactin and rhamnolipids are well-known biosurfactants. These compounds have several advantages over chemical surfactants, however they are not economically competitive, since their production cost is up to 12 times higher than chemical surfactants. In this sense, an interesting approach is to replace synthetic culture medium, which represents ≈ 30% of the production cost by agro-industrial wastes. In addition, biosurfactant productivity can be easily enhanced by inductor supplementation into culture medium that triggers biosurfactant metabolism. Biosurfactant inducers are mainly a pool of hydrophobic molecules (e.g. olive oil-saturated and unsaturated fatty acids, proteins and vitamins). Nevertheless, there is little information on inducer effects of specific molecules (e.g. oleic acid). In general, hydrophobic inducers lead to higher fatty acid chain lengths (biosurfactant chemical structure). Therefore, the aim of this review was to critically discuss the current state of the art and future trends on biosurfactant production, in particular biosurfactant inducers. Taking into account the last 10 years, there is a clear lack of information on correlation between "inducers" or "hydrophobic inducers" AND "biosurfactants", since only 13 documents were found (Scopus database). Thus, it is essential to deeply investigate all inducer effects on biosurfactant production, mainly yield and chemical structure.

Organ-specific toxicity evaluation of stearamidopropyl dimethylamine (SAPDMA) surfactant using zebrafish embryos

Surfactants are widely used in the industry of detergents, household products, and cosmetics. SAPDMA is a cationic surfactant that is used mostly in cosmetics, conditioning agents and has recently gained attention as a corrosion inhibitor in the sea pipelines industry. In this regard, literature concerning the ecotoxicological classification of SAPDMA on aquatic animals is lacking. This study aims to evaluate the potential ecotoxicity of SAPDMA using the aquatic zebrafish embryo model. The potential toxic effects of SAPDMA were assessed by different assays. This includes (i) mortality/survival assay to assess the median lethal concentration (LC₅₀); (ii) teratogenicity assay to assess the no observed effect concentration (NOEC); (iii) organ-specific toxicity assays including cardiotoxicity, neurotoxicity (using locomotion assay), hematopoietic toxicity (hemoglobin synthesis using o-dianisidine staining), hepatotoxicity (liver steatosis and yolk retention using Oil Red O (ORO) stain); (iv) cellular cytotoxicity (mitochondrial membrane potential) by measuring the accumulation of JC-1 dye into mitochondria. Exposure of embryos to SAPDMA caused mortality in a dose-dependent manner with a calculated LC₅₀ of 2.3 mg/L. Thus, based on the LC₅₀ value and according to the Fish and Wildlife Service (FWS) Acute Toxicity Rating Scale, SAPDMA is classified as "moderately toxic". The No Observed Effect Concentration (NOEC) concerning a set of parameters including scoliosis, changes in body length, yolk, and eye sizes was 0.1 mg/L. At the same NOEC concentration (0.1 mg/L), no organ-specific toxicity was detected in fish treated with SAPDMA, except hepatomegaly with no associated liver dysfunctions. However, higher SAPDMA concentrations (0.8 mg/L) have dramatic effects on zebrafish organ development (eye, heart, and liver development). Our data recommend a re-evaluation of the SAPDMA employment in the industry setting and its strictly monitoring by environmental and public health agencies.

Environmental behaviour and ecotoxicity of cationic surfactants towards marine organisms

Cationic surfactants are surface-active compounds that can be found in many products, including household and cleaning agents. As a consequence, they tend to be discarded into water streams, ultimately ending up in the aquatic environment. In spite of this environmental issue, studies describing their effects towards marine species are lacking. The aim of this study was therefore to evaluate the short-term exposure effects of two commercial cationic surfactants and three novel gemini surfactants on four marine species, the green microalgae Nannochloropsis gaditana and Tetraselmis chuii, the diatom Phaeodactylum tricornutum, and the crustacean Artemia salina. Furthermore, biodegradation and size distribution of the cationic surfactants in artificial seawater were also studied by UV-vis spectrophotometry and dynamic light scattering, respectively. Ecotoxicity tests revealed that the commercial cationic surfactant N-cetyl-N,N,N-trimethylammonium bromide is toxic to all tested marine species while N-dodecyl-N,N,N-trimethylammonium chloride and 1,4-bis-[N-(1-dodecyl)-N,N-dimethylammoniummethyl]benzene dibromide showed the lowest toxicity among the tested cationic surfactants. Besides the novel insights regarding the effects caused by these five cationic surfactants, this work opens prospects for the replacement of commercially available surfactants by more environmentally friendly alternatives.

Enhanced deflocculation of dehydrated sludge by rhamnolipid treatment coupled with thermal hydrolysis

The effect of a biosurfactant, rhamnolipid (RL), coupled with a thermal treatment was investigated to determine its impact on improving the deflocculation of dehydrated sludge from wastewater treatment processes. Results showed that the RL treatment positively impacted sludge conditioning to weak acidity and hydrolyzed the carbohydrates and proteins released from the matrix of the extracellular polymeric substance. When RL was coupled with high temperature thermal treatments (65 and 95 °C), soluble chemical oxygen demand and chemical oxygen demand solubilization increased by 9.6-19.7 times and 13.4-29.3%, respectively. The RL treatment reduced antibiotic resistant bacteria by 5.4-98.4%, and antibiotic activity was further accelerated by high temperature thermal treatment. The combination of biosurfactant and thermal treatment can effectively deflocculate dehydrated sludge and should be considered an alternative technology for the sludge management process.

Evaluation of potential environmental toxicity of polymeric nanomaterials and surfactants

Nanomaterials have gained huge importance in various fields including nanomedicine. Nanoformulations of drugs and nanocarriers are used to increase pharmaceutical potency. However, it was seen that polymeric nanomaterials can cause negative effects. Thus, it is essential to identify nanomaterials with the least adverse effects on aquatic organisms. To determine the toxicity of polymeric nanomaterials, we investigated the effects of poly(lactic-co-glycolid) acid (PLGA), Eudragit® E 100 and hydroxylpropyl methylcellulose phthalate (HPMCP) on zebrafish embryos using the fish embryo toxicity test (FET). Furthermore, we studied Cremophor® RH40, Cremophor® A25, Pluronic® F127 and Pluronic® F68 applied in the generation of nanoformulations to identify the surfactant with minimal toxic impact. The order of ecotoxicty was HPMCP < PLGA < Eudragit® E100 and Pluronic® F68 < Pluronic® F127 < Cremophor® RH40 < Cremophor® A25. In summary, HPMCP and Pluronic® F68 displayed the least toxic impact, thus suggesting adequate environmental compatibility for the generation of nanomedicines.

A KBr-impregnated paper substrate as a sample probe for the enhanced ATR-FTIR signal strength of anionic and non-ionic surfactants in an aqueous medium

Herein, we report a KBr-impregnated paper substrate as a sample probe to enhance the attenuated total reflection-Fourier transform infrared (ATR-FTIR) signal strength of anionic surfactants (AS) and non-ionic surfactants (NS) in an aqueous solution. The mechanism for the sensing of AS and NS is based on the strong interaction of surfactants with the silicate groups (SiO₄⁴⁻) of the KBr-impregnated paper substrate. The role of SiO₄⁴⁻ on the surface of the paper is to enhance the adsorption of AS and NS, resulting in improved IR signal intensities for the target analytes. The improved signal intensity at 1253 cm⁻¹ (SO₄²⁻, symmetric stretching) for AS and 1114 cm⁻¹ (C–O–C, stretching vibration) for NS were selected for quantification. SEM-EDX was employed to determine the elemental compositions of pre- and post-adsorbed AS and NS on glass fibre filter paper (GFF). The linear range for the determination of AS and NS was 10–100 μg L⁻¹ with a method detection limit (MDL) of 4 μg L⁻¹ and method quantification limit (MQL) of 12 μg L⁻¹. The good relative recovery of 71.4–109.7% and the interference studies showed the selectivity of the method for the determination of AS and NS in environmental water and commodity samples. The advantages of this method include its cost-effectiveness, enhanced sensitivity, disposability and accessibility of the paper substrate.

Flow diagram of the procedures for the analysis of surfactants using modified GFF paper substrate.

Potentiometric Sensors for the Determination of Anionic Surfactants - A Review

Anionic surfactants are important components of many products used in everyday life in all households. They are also applied in various industrial fields at a very large scale. Since they have a negative influence on the environment, it is an imperative to monitor their concentration in aquatic ecosystems. Therefore, it is of great importance to develop new methods for the determination of a wide spectra of anionic surfactants in complex environmental samples in a short time. A comprehensive review of potentiometric sensors for the determination of anionic surfactants in the last 50 years is given with special concern to papers published since 2000, but noting some earlier published important papers. The latest development in use of new ionophores, polymer formulations, and nanomaterials is presented. Additionally, the application of new potentiometric sensors in batch mode or in miniaturized microfluidic methods is discussed.

A novel microbial technique for producing high-quality sophorolipids from horse oil suitable for cosmetic applications

Horse oil contains linoleic, palmitoleic and unsaturated fatty acids that are similar to those in human skin, and may therefore be an ideal substance from which to isolate biosurfactants for cosmetic products to improve human skin quality. Herein, an innovative approach was developed to synthesise sophorolipids from horse oil by hydrolysis, followed by fermentation using the yeast Candida bombicola. The yield of sophorolipids from direct fermentation of horse oil and hydrolysed horse oil was 40.6 ± 1.3 g l^-1 and 58.4 ± 1.8 g l^-1 respectively. To further increase the yield, 30-40 g l^-1 glucose was added in a fed-batch fermentation process to maintain the pH between 4.0 and 4.5, resulting in a conversion yield of 71.7 ± 0.8 g l^-1 . The purity and structure of the synthesised sophorolipids were analysed by ultra-performance liquid chromatography-mass spectrometry and nuclear magnetic resonance. An in vitro human dermal fibroblast model was used as a surrogate for human skin to measure elastase inhibition activity. Antiwrinkle properties of isolated sophorolipids were better than those of horse oil or hydrolysed horse oil in several in vitro assays. Furthermore, no cytotoxicity was observed at a concentration of 50 μg ml^-1 , and wound-healing capacity was evident in a cell culture model. Additionally, the synthesised sophorolipids attenuated lipopolysaccharide-induced expression of inflammatory cytokines in macrophages, and efficiently inhibited several strains of bacteria and yeast. In conclusion, fed-batch fermentation of hydrolysed horse oil is a novel and efficient approach for producing high-quality and high-yield sophorolipids that exhibit great potential as cosmetic ingredients.

Identification of surfactants and its correlation with physicochemical parameters at the confluence region of Vembanad Lake in India

The present study describes the monitoring of some of the major classes of surfactants in water. The separation, identification, and the quantitative estimation of the compounds were achieved using LC-Q-ToF-MS. The analyses revealed the presence of variety of surfactants including linear alkylbenzene sulfonate (LAS), alcohol ethoxysulfates (AES), and alcohol ethoxylates (AE). Further, emphasis was given to AES as they are one of the most produced and consumed surfactants in the world. And as far as India is concerned, the present study is one of the most significant attempt regarding the identification and quantification of AES. The data obtained during the analysis revealed that the average concentration of AES C12Ex varied from 0.7 to 13.6 μg L^-1 while that of C14Ex ranged between 1.3 and 10.4 μg L^-1. The risk assessment revealed that higher chain AES are capable of posing medium level risk to the aquatic compartment. In addition, the study also included the physicochemical analysis of water from the selected area. Water was found to be acidic in nature and the salinity, TDS, and EC values were found to be high during the pre-monsoon season. The order of the levels of anionic constituents was of Cl^->SO₄^2-SO₄^2->F^->NO₃^2- ≅ PO₄^2- while that of cations were Na⁺ > Mg²⁺ > K⁺ > Ca²⁺. Results of correlation analysis showed that statistically negative correlation exists between AES homologs and pH while slight positive correlations were found between AES and other parameters including TDS and EC. The suitability of this water for domestic and agricultural purposes has been examined on the ground of basic quality indices such as the water quality index (WQI) and sodium adsorption ratio (SAR). The WQI measurements also revealed that the water quality of the region falls under the "very poor" category especially during the pre-monsoon season. The study could explore the cumulative share of these canals in the quality impairment of the receiving Vembanad Lake.

Benzalkonium Chloride and Anticancer Drugs in Binary Mixtures: Reproductive Toxicity and Genotoxicity in the Freshwater Crustacean Ceriodaphnia dubia

Benzalkonium chloride (BAC) is a cationic surfactant commonly used as a disinfectant. Its ubiquitous nature is the result of high usage and frequent discharge into the environment and evidence of interaction with numerous contaminants, such as pharmaceutical active compound residues. Anticancer drugs, among these compounds, are able to exert eco-genotoxic effects at sub ng-µg/L. The purpose of this study was to assess the reproductive toxicity and the genotoxicity of 5-fluorouracil (5-FU), cisplatin (CDDP), etoposide (ET), and imatinib mesylate (IM)-binary mixtures combined with BAC in Ceriodaphnia dubia. The effects of the mixtures were assessed under the assumption of independent action in experiments that applied two effect levels. The type of interaction was not the same over the range of effect sizes. The combined action experiment on reproduction showed an antagonistic effect at higher effect levels for all binary combinations, except for BAC/IM, whereas independent action was observed in all mixtures at a low effect level. The results of binary combinations on genotoxicity showed antagonistic effects for BAC + ET and BAC + CDDP, whereas independence was expressed in BAC + IM and BAC + 5-FU. The antagonistic interactions still led to higher effects than those observed after single exposures at the same doses in most cases. The effects of mixtures of drugs should be taken into account for environmental risk assessment.

Surfactant removal with multiwalled carbon nanotubes

The ability of multiwalled carbon nanotubes (MWCNTs) to remove a non-ionic surfactant, Triton X-100 (TX100), an anionic surfactant, sodium dodecylbenzenesulonate (SDBS), and a cationic surfactant, hexadecyltrimethylammonium bromide (CTAB) from the aqueous phase was investigated. Untreated, OH-, and COOH-functionalized MWCNTs with different outer diameters and chemical composition were examined and compared. As both the concentrations of surfactants and MWCNTs initially added may affect removal efficiency of surfactants, a relationship between the initial concentration ratio of surfactants and MWCNTs (R_c) and the removal efficiency (E) was established. The results showed that for a given R_c (e.g., 0.8), removal efficiency of the tested surfactants by a specific MWCNT (e.g., the untreated one with outer diameter <8 nm) decreased in the following order: TX100 (52.3%) > SDBS (26.2%) > CTAB (3.8%). TX100 was more readily removed by MWCNTs than SDBS and CTAB, due to its longer aliphatic chain compared to SDBS and CTAB thus higher hydrophobicity, and stronger π-π interactions with the aromatic structure of the surfaces of graphite sheets relative to CTAB. Based upon the established relationship between R_c and E of surfactants by MWCNTs, the maximum removal efficiency and the most appropriate R_c of TX100 and SDBS by two MWCNTs (UT8 and OH8) were derived. It was interesting to notice that, except for the case to remove TX100 using UT8, even though a large quantity of UT8 or OH8 was added to the TX100 or SDBS removal systems, they cannot be completely removed, with the maximum removal efficiency in the range of 55.88-87.17%. This mostly resulted from strong aggregation of MWCNTs thus reducing their readily accessible surface area and porosity for sorption.

Monsoonal variations in atmospheric surfactants at different coastal areas of the Malaysian Peninsula

This study determined the effect of monsoonal changes on the composition of atmospheric surfactants in coastal areas. The composition of anions (SO4(2-), NO3(-), Cl(-), F(-)) and the major elements (Ca, K, Mg, Na) in aerosols were used to determine the possible sources of surfactants. Surfactant compositions were determined using a colorimetric method as methylene blue active substances (MBAS) and disulphine blue active substances (DBAS). The anion and major element compositions of the aerosol samples were determined by ion chromatography (IC) and inductively coupled plasma mass spectrometry (ICP-MS), respectively. The results indicated that the concentrations of surfactant in aerosols were dominated by MBAS (34-326pmolm(-3)). Monsoonal changes were found to significantly affect the concentration of surfactants. Using principal component analysis-multiple linear regressions (PCA-MLR), major possible sources for surfactants in the aerosols were motor vehicle emissions, secondary aerosol and the combustion of biomass along with marine aerosol.

Potential of pure and mixed cultures of Cladosporium cladosporioides and Geotrichum candidum for application in bioremediation and detergent industry

The effect of ethoxylated oleyl–cetyl alcohol (Henkel, “Merima”, Serbia) on the growth and metabolic activity of Cladosporium cladosporioides, Geotrichum candidum and their mixed culture was in the focus of this paper. The cultures were grown in Czapek-Dox liquid nutrient medium with the addition of 0.5% pollutant and without it. The physico-chemical and biochemical changes of pH, the total biomass dry weight, the quantity of free and total organic acids, proteolytic activity and the quality of carbohydrates were evaluated from 4th to 19th day of fungal growth. The pollutant caused an inhibitory effect on biomass dry weight of C. cladosporioides and G. candidum for 10.36% and 4.65% respectively, and stimulatory effect on biomass of mixed culture for 3.80%. The pollutant had influence on the decrease in pH value of the media in the phase of culture growth, and pH changes were correlated with the amount of excreted total organic acids. The highest quantity of free and total organic acids was noted in media with pollutant of mixed culture and C. cladosporioides, respectively. The alkaline protease activities of C. cladosporioides, G. candidum and mixed culture were enhanced by addition of pollutant for 56.88%, 55.84% and 30.94% respectively. The obtained results indicate the potential of both pure and mixed cultures in mycoremediation environment contaminated by alcohol ethoxylated and detergent industry.

Exploring the Effects of Different Types of Surfactants on Zebrafish Embryos and Larvae

Currently, surfactants are widely distributed in the environment. As organic pollutants, their toxicities have drawn extensive attention. In this study, the effects of anionic [sodium dodecyl sulphate (SDS) ], cationic [dodecyl dimethyl benzyl ammonium chloride (1227)] and non-ionic [fatty alcohol polyoxyethylene ether (AEO) ] surfactants on zebrafish larval behaviour were evaluated. Five behavioural parameters were recorded using a larval rest/wake assay, including rest total, number of rest bouts, rest bouts length, total activity and waking activity. The results revealed that 1227 and AEO at 1 μg/mL were toxic to larval locomotor activity and that SDS had no significant effects. Moreover, we tested the toxicities of the three surfactants in developing zebrafish embryos. AEO exposure resulted in smaller head size, smaller eye size and shorter body length relative to SDS and 1227. All three surfactants incurred concentration-dependent responses. Furthermore, in situ hybridisation indicated that smaller head size may be associated with a decreased expression of krox20. The altered expression of ntl demonstrated that the developmental retardation stemmed from inhibited cell migration and growth. These findings provide references for ecotoxicological assessments of different types of surfactants, and play a warning role in the application of surfactants.

Surfactants in atmospheric aerosols and rainwater around lake ecosystem

This study was conducted to determine the composition of surfactants in atmospheric aerosols and rainwater in the vicinity of Lake Chini, Malaysia. Samples of atmospheric aerosol and rainwater were collected between March and September 2011 using a high volume air sampler (HVAS) and glass bottles equipped with funnel. Colorimetric analysis was undertaken to determine the concentration of anionic surfactants as methylene blue active substances (MBAS) and cationic surfactants as disulphine blue active substances (DBAS). The water-soluble ionic compositions were determined using inductively coupled plasma mass spectrometry for cations (Na, K, Mg and Ca) and ion chromatography equipped with a conductivity detector for anions (F(-), Cl(-), NO3(-), and SO4(2-)) and the Nessler Method was used to obtain the NH4(+) concentrations. The source apportionment of MBAS and DBAS in atmospheric aerosols was identified using a combination of principal component analysis (PCA) and multiple linear regression (MLR). The results revealed that the concentrations of surfactants in atmospheric aerosols and rainwater were dominated by anionic surfactants as MBAS. The concentration of surfactants as MBAS and DBAS was dominated in fine mode compared to coarse mode aerosols. Using PCA/MLR analysis, two major sources of atmospheric surfactants to Lake Chini were identified as soil dust (75 to 93%) and biomass burning (2 to 22%).

Surfactants in the sea-surface microlayer and atmospheric aerosol around the southern region of Peninsular Malaysia

This study was conducted to determine the composition of surfactants in the sea-surface microlayer (SML) and atmospheric aerosol around the southern region of the Peninsular Malaysia. Surfactants in samples taken from the SML and atmospheric aerosol were determined using a colorimetric method, as either methylene blue active substances (MBAS) or disulphine blue active substances (DBAS). Principal component analysis with multiple linear regressions (PCA-MLR), using the anion and major element composition of the aerosol samples, was used to determine possible sources of surfactants in atmospheric aerosol. The results showed that the concentrations of surfactants in the SML and atmospheric aerosol were dominated by anionic surfactants and that surfactants in aerosol were not directly correlated (p>0.05) with surfactants in the SML. Further PCA-MLR from anion and major element concentrations showed that combustion of fossil fuel and sea spray were the major contributors to surfactants in aerosol in the study area.