Biomechanical evaluation of ascending aortic aneurysms

Mechanics of ascending aortic aneurysms based on a modulus of elasticity dependent on aneurysm diameter and pressure

The mechanical stresses and strains are examined, in ascending thoracic aortic aneurysm (aTAA) models, in a patient-specific aTAA as well as in healthy thoracic aortic models, via Finite Element Analysis. The aneurysms are assumed spherical, 1.5 mm thick, with diameters between 47 mm and 80 mm, eccentrically positioned. The geometry and wall thickness distribution of the aorta along its length are based on open literature data for an average patient age of 66.25 years, accounting for the Body Surface Area (BSA) parameter. The vessel wall material is assumed isotropic and incompressible, with its Young's modulus varying with the aneurysm diameter and the applied intraluminal pressure (120 mmHg to 240 mmHg). In the aTAAs, peak stresses were found to increase nonlinearly with aneurysm diameter (for a given pressure) tending to reach a plateau, appearing at the proximal area of the aneurysm, whereas lower stresses were found at its distal part and even smaller at the aneurysm maximum diameter. Regarding the patient-specific aTAA model, the peak stresses appeared at the distal part of the aneurysm where a tear of the intima layer was detected during surgical intervention. Peak strains exhibited for each pressure a maximum at a certain aneurysm diameter beyond which they dropped so that essentially the vessel wall's distensibility was thus reduced. Examining more than 100 geometry cases and employing a failure stress criterion, the rupture diameter thresholds were estimated to be 65, 52.5, 50 and 47.5 mm for a pressure of 120, 160, 200 and 240 mmHg respectively.

Bicuspid Valve Aortopathy: Is It Reasonable to Define a Different Surgical Cutoff Based on Different Aortic Wall Mechanical Properties Compared to Those of the Tricuspid Valve?

BACKGROUND

In this study, we examined and compared ex vivo mechanical properties of aortic walls in patients with bicuspid (BAV) and tricuspid (TAV) aortic valve aortopathy to investigate if the anatomical peculiarities in the BAV group are related to an increased frailty of the aortic wall and, therefore, if a different surgical cutoff point for ascending aortic replacement could be reasonable in such patients.

METHODS

Ultimate stress tests were performed on fresh aortic wall specimens harvested during elective aortic surgery in BAV (n. 33) and TAV (n. 77) patients. Three mechanical parameters were evaluated at the failure point, under both longitudinal and circumferential forces: the peak strain (Pstr), peak stress (PS), and maximum elastic modulus (EM). The relationships between the three mechanical parameters and preoperative characteristics were evaluated, with a special focus on evaluating potential risk factors for severely impaired mechanical properties, cumulatively and comparatively (BAV vs. TAV groups).

RESULTS

The patient populations were inhomogeneous, as BAV patients reached surgical indication, according to the maximum aortic dilatation, at a younger age (58 ± 15 vs. 64 ± 13; p = 0.0294). The extent of the maximum aortic dilatation was, conversely, similar in the two groups (52 ± 4 vs. 54 ± 7; p = 0.2331), as well as the incidences of different phenotypes of aortic dilatation (with the ascending aorta phenotype being the most frequent in 81% and 66% of the BAV and TAV patients, respectively (p = 0.1134). Cumulatively, the mechanical properties of the aortic wall were influenced mainly by the orientation of the force applied, as both PS and EM were impaired under longitudinal stress. An age of >66 and a maximum dilatation of >52 mm were shown to predict severe Pstr reduction in the overall population. Comparative analysis revealed a trend of increased mechanical properties in the BAV group, regardless of the position, the force orientation, and the phenotype of the aortic dilatation.

CONCLUSIONS

BAV aortopathy is not correlated with impaired mechanical properties of the aortic wall as such. Different surgical cutoff points for BAV aortopathy, therefore, seem to be unjustified. An age of >66 and a maximum aortic dilatation of >52 mm, however, seem to significantly influence the mechanical properties of the aortic wall in both groups. These findings, therefore, could suggest the need for more accurate monitoring and evaluation in such conditions.

Aortic wall thickness in dilated ascending aorta: Comparison between tricuspid and bicuspid aortic valve

BACKGROUND

Bicuspid aortic valve (BAV) is frequently associated with dilatation of the thoracic aorta. Peculiar anatomical, histological and mechanical changes of the aortic wall in BAV aortopathy have been hypothesized to suggest an increased risk of acute aortic complications in patients with BAV.

AIM

In this study we tried to clarify any differences in the adaptability of the aortic wall to the mechanism of dilatation between patients with BAV and those with TAV.

METHODS

In total, 354 samples were taken from 71 patients undergoing elective aortic surgery and divided into two groups: BAV group (n=16; 101 samples); and TAV group (n=55; 253 samples). Aortic wall thickness was measured with a dedicated caliper. The relationship between aortic wall thickness and aortic dilatation and demographic variables was evaluated cumulatively and comparatively (BAV versus TAV). In patients with more than three samples available, intrapatient variability was also studied. Finally, potential risk factors for severely reduced aortic wall thickness were also assessed.

RESULTS

Analysis of preoperative characteristics revealed significant differences in patient age (54±16years for BAV and 66±11years for TAV; P=0.0011), with no differences in variables related to aortic dilatation (including phenotype). Cumulative aortic wall thickness was significantly thinner in the anterior than in the posterior wall. In the comparative analysis, aortic wall thickness was significantly thinner in patients with BAV in both the anterior and posterior regions. Furthermore, in patients with BAV, dilatation>51mm was a significant predictor of severely reduced aortic wall thickness.

CONCLUSIONS

In our experience, patients with BAV aortopathy reached the cut-off for the surgical indication at an early age. Careful monitoring in patients with BAV is mandatory when aortic dilatation has reached 51mm, as it is related to significant anatomical changes.

A review on the biomechanical behaviour of the aorta

Large aortic aneurysm and acute and chronic aortic dissection are pathologies of the aorta requiring surgery. Recent advances in medical intervention have improved patient outcomes; however, a clear understanding of the mechanisms leading to aortic failure and, hence, a better understanding of failure risk, is still missing. Biomechanical analysis of the aorta could provide insights into the development and progression of aortic abnormalities, giving clinicians a powerful tool in risk stratification. The complexity of the aortic system presents significant challenges for a biomechanical study and requires various approaches to analyse the aorta. To address this, here we present a holistic review of the biomechanical studies of the aorta by categorising articles into four broad approaches, namely theoretical, in vivo, experimental and combined investigations. Experimental studies that focus on identifying mechanical properties of the aortic tissue are also included. By reviewing the literature and discussing drawbacks, limitations and future challenges in each area, we hope to present a more complete picture of the state-of-the-art of aortic biomechanics to stimulate research on critical topics. Combining experimental modalities and computational approaches could lead to more comprehensive results in risk prediction for the aortic system.

Nondestructive Evaluation of Mechanical and Histological Properties of the Human Aorta With Near-Infrared Spectroscopy

INTRODUCTION

Ascending aortic dilatation is a well-known risk factor for aortic rupture. Indications for aortic replacement in its dilatation concomitant to other open-heart surgery exist; however, cut-off values based solely on aortic diameter may fail to identify patients with weakened aortic tissue. We introduce near-infrared spectroscopy (NIRS) as a diagnostic tool to nondestructively evaluate the structural and compositional properties of the human ascending aorta during open-heart surgeries. During open-heart surgery, NIRS could provide information regarding tissue viability in situ and thus contribute to the decision of optimal surgical repair.

MATERIALS AND METHODS

Samples were collected from patients with ascending aortic aneurysm (n = 23) undergoing elective aortic reconstruction surgery and from healthy subjects (n = 4). The samples were subjected to spectroscopic measurements, biomechanical testing, and histological analysis. The relationship between the near-infrared spectra and biomechanical and histological properties was investigated by adapting partial least squares regression.

RESULTS

Moderate prediction performance was achieved with biomechanical properties (r = 0.681, normalized root-mean-square error of cross-validation = 17.9%) and histological properties (r = 0.602, normalized root-mean-square error of cross-validation = 22.2%). Especially the performance with parameters describing the aorta's ultimate strength, for example, failure strain (r = 0.658), and elasticity (phase difference, r = 0.875) were promising and could, therefore, provide quantitative information on the rupture sensitivity of the aorta. For the estimation of histological properties, the results with α-smooth muscle actin (r = 0.581), elastin density (r = 0.973), mucoid extracellular matrix accumulation(r = 0.708), and media thickness (r = 0.866) were promising.

CONCLUSIONS

NIRS could be a potential technique for in situ evaluation of biomechanical and histological properties of human aorta and therefore useful in patient-specific treatment planning.

Ex Vivo Analysis of an Association of Mechanical Strength of Dilated Ascending Aorta with Tissue Matrix Metalloproteinases and Cytokines

We analyzed the associations of the mechanical strength of dilated ascending aorta wall (intraoperative samples from 30 patients with non-syndromic aneurysms) with tissue MMPs and the cytokine system. Some samples were stretched to break on an Instron 3343 testing machine and the tensile strength was calculated; others were homogenized and the concentrations of MMP-1, MMP-2, MMP-7, their inhibitors (TIMP-1 and TIMP-2), and pro- and anti-inflammatory cytokines were determined by ELISA. Direct correlations between aortic tensile strength and concentrations of IL-10 (r=0.46), TNFα (r=0.60), and vessel diameter (r=0.67) and an inverse correlation with patient's age (r=-0.59) were revealed. Compensatory mechanisms supporting the strength of the ascending aortic aneurysm are possible. No associations of MMP-1, MMP-7, TIMP-1, and TIMP-2 with tensile strength and aortic diameter were found.

Cysteine-rich protein 2 deficiency attenuates angiotensin II-induced abdominal aortic aneurysm formation in mice

Background

Abdominal aortic aneurysm (AAA) is a relatively common and often fatal condition. A major histopathological hallmark of AAA is the severe degeneration of aortic media with loss of vascular smooth muscle cells (VSMCs), which are the main source of extracellular matrix (ECM) proteins. VSMCs and ECM homeostasis are essential in maintaining structural integrity of the aorta. Cysteine-rich protein 2 (CRP2) is a VSMC-expressed protein; however, the role of CRP2 in AAA formation is unclear.

Methods

To investigate the function of CRP2 in AAA formation, mice deficient in Apoe (Apoe^−/−) or both CRP2 (gene name Csrp2) and Apoe (Csrp2^−/−Apoe^−/−) were subjected to an angiotensin II (Ang II) infusion model of AAA formation. Aortas were harvested at different time points and histological analysis was performed. Primary VSMCs were generated from Apoe^−/− and Csrp2^−/−Apoe^−/− mouse aortas for in vitro mechanistic studies.

Results

Loss of CRP2 attenuated Ang II-induced AAA incidence and severity, accompanied by preserved smooth muscle α-actin expression and reduced elastin degradation, matrix metalloproteinase 2 (MMP2) activity, deposition of collagen, particularly collagen III (Col III), aortic tensile strength, and blood pressure. CRP2 deficiency decreased the baseline MMP2 and Col III expression in VSMCs and mitigated Ang II-induced increases of MMP2 and Col III via blunting Erk1/2 signaling. Rescue experiments were performed by reintroducing CRP2 into Csrp2^−/−Apoe^−/− VSMCs restored Ang II-induced Erk1/2 activation, MMP2 expression and activity, and Col III levels.

Conclusions

Our results indicate that in response to Ang II stimulation, CRP2 deficiency maintains aortic VSMC density, ECM homeostasis, and structural integrity through Erk1/2–Col III and MMP2 axis and reduces AAA formation. Thus, targeting CRP2 provides a potential therapeutic strategy for AAA.

Supplementary information

The online version contains supplementary material available at 10.1186/s12929-022-00808-z.

Ascending aorta mechanics and dimensions in aortopathy – from science to application

The ascending aorta has a unique microstructure and biomechanical properties that allow it to absorb energy during systole and return energy during diastole (Windkessel effect). Derangements in aortic architecture can result in changes to biomechanics and inefficiencies in function. Ultimately biomechanical failure may occur resulting in aortic dissection or rupture. By measuring aortic biomechanics with either in vivo or ex vivo methods, one may be able to predict tissue failure in patients with aortic disease such as aneurysms. An understanding of the biomechanical changes that lead to these tissue-level failures may help guide therapy, disease surveillance, surgical intervention, and aid in the development of new treatments for this deadly condition.

Characterization of the dynamic viscoelastic response of the ascending aorta imposed via pulsatile flow

This study characterizes the material properties of a viscoelastic, ex vivo porcine ascending aorta under dynamic-loading conditions via pulsatile flow. The deformation of the opaque vessel wall and the pulsatile flow field inside the vessel were recorded using ultrasound imaging. The internal pressure was extracted from the pulsatile flow results and, when coupled with the vessel-wall expansion, was used to calculate the instantaneous elastic modulus from a novel, time-resolved two-dimensional (i.e. axial and circumferential) stress model. The circumferential instantaneous elasticity obtained from the two-dimensional stress model was found to match the uniaxial tensile test for strains below 50%. The agreement in elasticity between the two stress states reveals that the two-dimensional stress model accurately resolves the circumferential stress of the viscoelastic aorta at physiological strains (8%-30%). At higher strains, results from pulsatile flow generated a more compliant response than the uniaxial measurements. Viscoelastic properties (storage modulus and loss factor) were also calculated using the two-dimensional stress model and compared to those obtained from uniaxial tests. While instantaneous elasticity matched between the cylindrical and uniaxial loading, the viscoelastic behaviour significantly diverged between stress states. The storage modulus obtained from the pulsatile flow data was dependent on mean Reynolds number, while the uniaxial storage modulus results exhibited a strong inverse dependency on the frequency. The loss factor for the pulsatile flow data increased alongside the frequency, while the uniaxial data indicated a constant loss factor over the entire frequency range. The results of the current study show that the two-dimensional stress model can accurately extract the material properties of the ex vivo porcine aorta.

A versatile biaxial testing platform for soft tissues

Uniaxial testing remains the most common modality of mechanical analysis for biological and other soft materials; however, biaxial testing enables a more comprehensive understanding of these materials' mechanical behavior. In recent years, a number of commercially available biaxial testing systems designed for biological materials have been produced; however, there are common limitations that are often associated with using these systems. For example, the range of allowable sample geometries are relatively constrained, the clamping systems are relatively limited with respect to allowable configurations, the load and displacement ranges are relatively small, and the software and control elements offer relatively limited options. Due to these constraints, there are significant benefits associated with designing custom biaxial testing systems that meet the technical requirements for testing a broad range of materials. Herein we present a design for a biaxial testing system with capabilities that extend beyond those associated with typical commercially available systems. Our design is capable of performing uniaxial tests, traditional biaxial tests, and double lap shear (simple shear) tests, in either a displacement or load control mode. Testing protocols have been developed and proof-of-concept experiments have been performed on commercially available silicone membranes and rat abdominal skin samples.

Computational modeling of the strength of the ascending thoracic aortic media tissue under physiologic biaxial loading conditions

Type A Aortic Dissection (TAAD) is a life-threatening condition involving delamination of ascending aortic media layers. While current clinical guidelines recommend surgical intervention for aneurysm diameter > 5.5 cm, high incidence of TAAD in patients below this diameter threshold indicates the pressing need for improved evidence-based risk prediction metrics. Construction of such metrics will require the knowledge of the biomechanical failure properties of the aortic wall tissue under biaxial loading conditions. We utilized a fiber-level finite element based structural model of the aortic tissue to quantify the relationship between aortic tissue strength and physiologically relevant biaxial stress state for nonaneurysmal and aneurysmal patient cohorts with tricuspid aortic valve phenotype. We found that the model predicted strength of the aortic tissue under physiologic biaxial loading conditions depends on the stress biaxiality ratio, defined by the ratio of the longitudinal and circumferential components of the tissue stress. We determined that predicted biaxial tissue strength is statistically similar to its uniaxial circumferential strength below biaxiality ratios of 0.68 and 0.69 for nonaneurysmal and aneurysmal cohorts, respectively. Beyond this biaxiality ratio, predicted biaxial strength for both cohorts reduced drastically to a magnitude statistically similar to its longitudinal strength. We identified fiber-level failure mechanisms operative under biaxial stress state governing aforementioned tissue failure behavior. These findings are an important first step towards the development of mechanism-based TAAD risk assessment metrics for early identification of high-risk patients.

Ascending aorta mechanics in bicuspid aortopathy: controversy or fact?

Bicuspid aortic valve is the most common congenital cardiovascular defect, often associated with proximal aortic dilatation, and the ideal management strategy is debated. The inconsistency in previous and present guideline recommendations emphasizes the insufficiency of the maximal diameter as the sole criterion for prophylactic repair. Our ability to guide clinical decisions may improve through an understanding of the mechanical properties of ascending thoracic aortic aneurysms in bicuspid compared to tricuspid aortic valve patients and non-aneurysmal aortas, because dissection and rupture are aortic wall mechanical failures. Such an understanding of the mechanical properties has been attempted by several authors, and this article addresses whether there is a controversy in the accumulated knowledge. The available mechanical studies are briefly reviewed, discussing factors such as age, sex, and the region of mechanical examination that may be responsible for the lack of unanimity in the reported findings. The rationale for acquiring layer-specific properties is presented along with the main results from our recent study. No mechanical vulnerability of ascending thoracic aortic aneurysms was evidenced in bicuspid aortic valve patients, corroborating present conservative guidelines concerning the management of bicuspid aortopathy. Weakening and additional vulnerability was evidenced in aged patients and those with coexisting valve pathology, aortic root dilatation, hypertension, and hyperlipidemia. Discussion of these results from age- and sex-matched subjects, accounting for the region- and layer-specific aortic heterogeneity, in relation to intact wall results and histologic confirmation, helps to reconcile previous findings and affords a universal interpretation of ascending aorta mechanics in bicuspid aortopathy.

Thermo-Mechanical Behaviour of Human Nasal Cartilage

The aim of this study was to undergo a comprehensive analysis of the thermo-mechanical properties of nasal cartilages for the future design of a composite polymeric material to be used in human nose reconstruction surgery. A thermal and dynamic mechanical analysis (DMA) in tension and compression modes within the ranges 1 to 20 Hz and 30 °C to 250 °C was performed on human nasal cartilage. Differential scanning calorimetry (DSC), as well as characterization of the nasal septum (NS), upper lateral cartilages (ULC), and lower lateral cartilages (LLC) reveals the different nature of the binding water inside the studied specimens. Three peaks at 60–80 °C, 100–130 °C, and 200 °C were attributed to melting of the crystalline region of collagen matrix, water evaporation, and the strongly bound non-interstitial water in the cartilage and composite specimens, respectively. Thermogravimetric analysis (TGA) showed that the degradation of cartilage, composite, and subcutaneous tissue of the NS, ULC, and LLC take place in three thermal events (~37 °C, ~189 °C, and ~290 °C) showing that cartilage releases more water and more rapidly than the subcutaneous tissue. The water content of nasal cartilage was estimated to be 42 wt %. The results of the DMA analyses demonstrated that tensile mode is ruled by flow-independent behaviour produced by the time-dependent deformability of the solid cartilage matrix that is strongly frequency-dependent, showing an unstable crystalline region between 80–180 °C, an amorphous region at around 120 °C, and a clear glass transition point at 200 °C (780 kJ/mol). Instead, the unconfined compressive mode is clearly ruled by a flow-dependent process caused by the frictional force of the interstitial fluid that flows within the cartilage matrix resulting in higher stiffness (from 12 MPa at 1 Hz to 16 MPa at 20 Hz in storage modulus). The outcomes of this study will support the development of an artificial material to mimic the thermo-mechanical behaviour of the natural cartilage of the human nose.

Comparative Analysis of Porcine and Human Thoracic Aortic Stiffness

OBJECTIVES

To compare porcine and human thoracic aortic stiffness using the available literature.

METHODS

The available literature was searched for studies reporting data on porcine or human thoracic aortic mechanical behaviour. A four fibre constitutive model was used to transform the data from included studies. Thus, equi-biaxial stress stretch curves were generated to calculate circumferential and longitudinal aortic stiffness. Analysis was performed separately for the ascending and descending thoracic aorta. Data on human aortic stiffness were divided by age <60 or ≥60 years. Porcine and human aortic stiffness were compared.

RESULTS

Eleven studies were included, six reported on young porcine aortas, four on human aortas of various ages, and one reported on both. In the ascending aorta, circumferential and longitudinal stiffness were 0.42±0.08 MPa and 0.37±0.06 MPa for porcine aortas (4-9 months) versus 0.55±0.15 MPa and 0.45±0.08 MPa for humans <60 years, and 1.02±0.59 MPa and 1.03±0.54 MPa for humans ≥60 years. In the descending aorta, circumferential and longitudinal stiffness were 0.46±0.03 MPa and 0.44±0.01 MPa for porcine aortas (4-10 months) versus 1.04±0.70 MPa and 1.24±0.76 MPa for humans <60 years, and 3.15±3.31 MPa and 1.17±0.31 MPa for humans ≥60 years.

CONCLUSIONS

The stiffness of young porcine aortic tissue shows good correspondence with human tissue aged <60 years, especially in the ascending aorta. Young porcine aortic tissue is less stiff than human aortic tissue aged ≥60 years.

Failure of the Porcine Ascending Aorta: Multidirectional Experiments and a Unifying Microstructural Model

The ascending thoracic aorta is poorly understood mechanically, especially its risk of dissection. To make better predictions of dissection risk, more information about the multidimensional failure behavior of the tissue is needed, and this information must be incorporated into an appropriate theoretical/computational model. Toward the creation of such a model, uniaxial, equibiaxial, peel, and shear lap tests were performed on healthy porcine ascending aorta samples. Uniaxial and equibiaxial tests showed anisotropy with greater stiffness and strength in the circumferential direction. Shear lap tests showed catastrophic failure at shear stresses (150-200 kPa) much lower than uniaxial tests (750-2500 kPa), consistent with the low peel tension (∼60 mN/mm). A novel multiscale computational model, including both prefailure and failure mechanics of the aorta, was developed. The microstructural part of the model included contributions from a collagen-reinforced elastin sheet and interlamellar connections representing fibrillin and smooth muscle. Components were represented as nonlinear fibers that failed at a critical stretch. Multiscale simulations of the different experiments were performed, and the model, appropriately specified, agreed well with all experimental data, representing a uniquely complete structure-based description of aorta mechanics. In addition, our experiments and model demonstrate the very low strength of the aorta in radial shear, suggesting an important possible mechanism for aortic dissection.

Two-dimensional speckle-tracking echocardiography for evaluation of dilative ascending aorta biomechanics

BACKGROUND

Two-dimensional (2D) echocardiography is one of the most feasible, noninvasive methods for assessing the aortic diameter and biomechanical changes. We studied possible interfaces between noninvasive biomechanical and speckle-tracking (ST) echocardiographic data from dilated aortas.

METHODS

Altogether, 44 patients with dilative pathology of ascending aorta (DPAA) were compared with subjects without ascending aortic dilation (diameter <40 mm). DPAA patients formed two groups based on diameter size: group 1, ≤45 mm diameter; group 2, >45 mm. Conventional and 2D-ST echocardiography were performed to evaluate peak longitudinal strain (LS), longitudinal (LD) and transverse (TD) displacement, and longitudinal velocity (VL). Aortic strain, distensibility, elastic modulus, stiffness index β of Valsalva sinuses and ascending aorta were also evaluated. SPSS version 20 was used for all analyses.

RESULTS

All linear diameters of the ascending aorta were increased in group 2 (>45 mm diameter) (p < 0.05). LD of the anterior aortic wall (p < 0.05) and TD of both aortic walls (p < 0.001) were least in group 2. VL of the posterior and anterior walls diminished in group 2 (p = 0.01). Aortic strain and distensibility were least (p = 0.028 and p = 0.001, respectively) and elastic modulus and stiffness index β values were greatest in group 2, although without statistical significance.

CONCLUSIONS

Ascending aortas of both DPAA groups had reduced elasticity and increased stiffness. The greatest changes in biomechanical parameters occurred in ascending aortas >45 mm. Longitudinal ascending aortic wall motion was mostly impaired in patients with aortas >45 mm (i.e., anterior aortic wall LD, VL of the posterior and anterior walls. TD of the posterior and anterior aortic walls was significantly lower in >45 mm aortic diameter patients. TD of 5.2 mm could predict aortic dilation >45 mm (area under the curve 0.76, p < 0.001, confidence interval 0.65-0.87; sensitivity 87%; specificity 63%). Greater aortic dilation is associated with reduced aortic stiffness parameters and increased elastic modulus and stiffness index β. Lower LD and LS were associated with less aortic strain and distensibility. There were no significant differences in 2D-ST echocardiographic or stiffness parameters between patients with tricuspid or bicuspid aortic valves.

Biaxial rupture properties of ascending thoracic aortic aneurysms

Although hundreds of samples obtained from ascending thoracic aortic aneurysms (ATAA) of patients undergoing elective surgical repair have already been characterized biomechanically, their rupture properties were always derived from uniaxial tensile tests. Due to their bulge shape, ATAAs are stretched biaxially in vivo. In order to understand the biaxial rupture of ATAAs, our group developed a novel methodology based on bulge inflation and full-field optical measurements. The objective of the current paper is threefold. Firstly, we will review the failure properties (maximum stress, maximum stretch) obtained by bulge inflation testing on a cohort of 31 patients and compare them with failure properties obtained by uniaxial tension in a previously published study. Secondly, we will investigate the relationship between the failure properties and the age of patients, showing that patients below 55years of age display significantly higher strength. Thirdly, we will define a rupture risk based on the extensibility of the tissue and we will show that this rupture risk is strongly correlated with the physiological elastic modulus of the tissue independently of the age, ATAA diameter or the aortic valve phenotype of the patient.

STATEMENT OF SIGNIFICANCE

Despite their medical importance, rupture properties of ascending thoracic aortic aneurysms (ATAA) subjected to biaxial tension were inexistent in the literature. In order to address this lack, our group developed a novel methodology based on bulge inflation and full-field optical measurements. Here we report rupture properties obtained with this methodology on 31 patients. It is shown for the first time that rupture occurs when the stretch applied to ATAAs reaches the maximum extensibility of the tissue and that this maximum extensibility correlates strongly with the elastic properties. The outcome is a better detection of at-risk individuals for elective surgical repair.

Inframammary Fold Reconstruction: A Biomechanical Analysis

Background:

Inframammary fold reconstruction has scarcely been evaluated in literature. No biomechanical analyses have been performed comparing different reconstructive methods. This evaluation compares the gold-standard suture reconstruction with an intrarib anchor system (Micro BioComposite SutureTak, Arthrex).

Methods:

Three analysis groups were compared including 8 Sawbone blocks, 22 embalmed cadaver, and 27 regular cadaver specimens (N = 57). Transient mechanical analysis was performed at 5 N/s using an Instron 5565 test frame.

Results:

Ultimate load favored the anchor system (compared with the gold-standard suture) by a factor of 9.8 (P < 0.0001) for the regular cadaver group and a factor of 1.7 (P < 0.038) for the embalmed cadaver group. A similar statistically significant benefit was shown for stiffness and load at 2-mm displacement.

Conclusions:

This analysis showed an anchor system to be the biomechanically superior fixation method in terms of ultimate load, fixation stiffness, and displacement at failure when compared with the gold-standard suture method in inframammary fold reconstruction. Because of superior stability in every aspect, an anchor system may be considered for inframammary fold reconstruction.

Biomechanical and biochemical properties of the thoracic aorta in warmblood horses, Friesian horses, and Friesians with aortic rupture

Background

Thoracic aortic rupture and aortopulmonary fistulation are rare conditions in horses. It mainly affects Friesian horses. Intrinsic differences in biomechanical properties of the aortic wall might predispose this breed. The biomechanical and biochemical properties of the thoracic aorta were characterized in warmblood horses, unaffected Friesian horses and Friesians with aortic rupture in an attempt to unravel the underlying pathogenesis of aortic rupture in Friesian horses. Samples of the thoracic aorta at the ligamentum arteriosum (LA), mid thoracic aorta (T1) and distal thoracic aorta (T2) were obtained from Friesian horses with aortic rupture (A), nonaffected Friesian (NA) and warmblood horses (WB). The biomechanical properties of these samples were determined using uniaxial tensile and rupture assays. The percentages of collagen and elastin (mg/mg dry weight) were quantified.

Results

Data revealed no significant biomechanical nor biochemical differences among the different groups of horses. The distal thoracic aorta displayed an increased stiffness associated with a higher collagen percentage in this area and a higher load-bearing capacity compared to the more proximal segments.

Conclusions

Our findings match reported findings in other animal species. Study results did not provide evidence that the predisposition of the Friesian horse breed for aortic rupture can be attributed to altered biomechanical properties of the aortic wall.

Electronic supplementary material

The online version of this article (doi:10.1186/s12917-015-0597-0) contains supplementary material, which is available to authorized users.