Studying the Properties of Chromium-Contaminated Soil Solidified by Polyurethane

The solidification of chromium-contaminated soil using polyurethane (PU) was systematically investigated. The unconfined compression test was conducted to investigate the effects of the curing time, PU dosage and the content of chromium ions on the unconfined compressive strength (UCS) of chromium-contaminated soil. The effect of the PU dosage on the pore structure was investigated using nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM), and the mechanism of strength change was revealed by combining the strength law with the pore structure development law. In addition, the ability of the PU to solidify the chromium-contaminated soil was studied by the toxicity characteristic leaching procedure (TCLP). According to the above test results, the UCS and the ability of the PU to solidify the chromium ions increased with the increase in curing time. The NMR tests showed that with the increase in PU dosage, the porosity decreased and the soil became more compact, hence increasing the strength. When the chromium ion content was 2000 mg/kg and the PU dosage was 8%, the strength of the sample was 0.37 MPa after curing for 24 h, which met the requirement of 0.35 MPa set by the U.S. Environmental Protection Agency. Consequently, PU is a solidification agent with high-early strength.

Implantable drug delivery systems for the treatment of osteomyelitis

Osteomyelitis is an infection of the bone tissue and bone marrow which is becoming increasingly difficult to treat due to the infection causing pathogens associated. Staphylococcus aureus is one of the main bacteria that causes this infection, which has a broad spectrum of antibiotic resistance making it extremely difficult to treat. Conventional metal implants used in orthopaedic applications often have the drawback of implant induced osteomyelitis as well as the requirement of a second surgery to remove the implant once it is no longer required. Recently, attention has been focused on the design and fabrication of biodegradable implants for the treatment of bone infection. The main benefit of biodegradable implants over polymethylmethacrylate (PMMA) based non-degradable systems is that they do not require a second surgery for removal and so making degradable implants safer and easier to use. The main purpose of a biodegradable implant is to provide the necessary support and conductivity to allow the bone to regenerate whilst themselves degrading at a rate that is compatible with the rate of formation of new bone. They must be highly biocompatible to ensure there is no inflammation or irritation within the surrounding tissue. During this review, the latest research into antibiotic loaded biodegradable implants will be explored. Their benefits and drawbacks will be compared with those non-degradable PMMA beads, which is the stable material used within antibiotic loaded implants. Biodegradable implants most frequently used are based on biodegradable natural and synthetic polymers. Implants can take the form of many different structures; the most commonly fabricated structure is a scaffold. Other structures that will be explored within this review are hydrogels, nanoparticles and surface coatings, all with their own benefits/drawbacks.

A Novel Resorbable Composite Material Containing Poly(ester-co-urethane) and Precipitated Calcium Carbonate Spherulites for Bone Augmentation-Development and Preclinical Pilot Trials

Polyurethanes have the potential to impart cell-relevant properties like excellent biocompatibility, high and interconnecting porosity and controlled degradability into biomaterials in a relatively simple way. In this context, a biodegradable composite material made of an isocyanate-terminated co-oligoester prepolymer and precipitated calcium carbonated spherulites (up to 60% w/w) was synthesized and investigated with regard to an application as bone substitute in dental and orthodontic application. After foaming the composite material, a predominantly interconnecting porous structure is obtained, which can be easily machined. The compressive strength of the foamed composites increases with raising calcium carbonate content and decreasing calcium carbonate particle size. When stored in an aqueous medium, there is a decrease in pressure stability of the composite, but this decrease is smaller the higher the proportion of the calcium carbonate component is. In vitro cytocompatibility studies of the foamed composites on MC3T3-E1 pre-osteoblasts revealed an excellent cytocompatibility. The in vitro degradation behaviour of foamed composite is characterised by a continuous loss of mass, which is slower with higher calcium carbonate contents. In a first pre-clinical pilot trial the foamed composite bone substitute material (fcm) was successfully evaluated in a model of vertical augmentation in an established animal model on the calvaria and on the lateral mandible of pigs.

Degradable Poly(ether-ester-urethane)s Based on Well-Defined Aliphatic Diurethane Diisocyanate with Excellent Shape Recovery Properties at Body Temperature for Biomedical Application

The aim of this study is to offer a new class of degradable shape-memory poly(ether-ester-urethane)s (SMPEEUs) based on poly(ether-ester) (PECL) and well-defined aliphatic diurethane diisocyanate (HBH) for further biomedical application. The prepolymers of PECLs were synthesized through bulk ring-opening polymerization using ε-caprolactone as the monomer and poly(ethylene glycol) as the initiator. By chain extension of PECL with HBH, SMPEEUs with varying PEG content were prepared. The chemical structures of the prepolymers and products were characterized by GPC, 1H NMR, and FT-IR, and the effect of PEG content on the physicochemical properties (especially the shape recovery properties) of SMPEEUs was studied. The microsphase-separated structures of the SMPEEUs were demonstrated by DSC and XRD. The SMPEEU films exhibited good tensile properties with the strain at a break of 483%-956% and an ultimate stress of 23.1-9.0 MPa. Hydrolytic degradation in vitro studies indicated that the time of the SMPEEU films becoming fragments was 4-12 weeks and the introduction of PEG facilitates the degradation rate of the films. The shape memory properties studies found that SMPEEU films with a PEG content of 23.4 wt % displayed excellent recovery properties with a recovery ratio of 99.8% and a recovery time of 3.9 s at body temperature. In addition, the relative growth rates of the SMPEEU films were greater than 75% after incubation for 72 h, indicating good cytocompatibility in vitro. The SMPEEUs, which possess not only satisfactory tensile properties, degradability, nontoxic degradation products, and cytocompatibility, but also excellent shape recovery properties at body temperature, promised to be an excellent candidate for medical device applications.

Candidate Polyurethanes Based on Castor Oil (Ricinus communis), with Polycaprolactone Diol and Chitosan Additions, for Use in Biomedical Applications

Polyurethanes are widely used in the development of medical devices due to their biocompatibility, degradability, non-toxicity and chemical versatility. Polyurethanes were obtained from polyols derived from castor oil, and isophorone diisocyanate, with the incorporation of polycaprolactone-diol (15% w/w) and chitosan (3% w/w). The objective of this research was to evaluate the effect of the type of polyol and the incorporation of polycaprolactone-diol and chitosan on the mechanical and biological properties of the polyurethanes to identify the optimal ones for applications such as wound dressings or tissue engineering. Polyurethanes were characterized by stress-strain, contact angle by sessile drop method, thermogravimetric analysis, differential scanning calorimetry, water uptake and in vitro degradation by enzymatic processes. In vitro biological properties were evaluated by a 24 h cytotoxicity test using the colorimetric assay MTT and the LIVE/DEAD kit with cell line L-929 (mouse embryonic fibroblasts). In vitro evaluation of the possible inflammatory effect of polyurethane-based materials was evaluated by means of the expression of anti-inflammatory and proinflammatory cytokines expressed in a cellular model such as THP-1 cells by means of the MILLIPLEX® MAP kit. The modification of polyols derived from castor oil increases the mechanical properties of interest for a wide range of applications. The polyurethanes evaluated did not generate a cytotoxic effect on the evaluated cell line. The assessed polyurethanes are suggested as possible candidate biomaterials for wound dressings due to their improved mechanical properties and biocompatibility.

Photo-cross-linked biodegradable hydrogels based on n-arm-poly(ethylene glycol), poly(ε-caprolactone) and/or methacrylic acid for controlled drug release

In this paper, a novel kind of photo-cross-linked biodegradable hydrogels based on n-arm-poly(ethylene glycol) ( n = 2, 3, and 4) and poly(ɛ-caprolactone) was prepared by ultraviolet-initiated free radical polymerization. The resulting n-arm-poly(ethylene glycol)-poly(ɛ-caprolactone) and n-arm-poly(ethylene glycol)-poly(ɛ-caprolactone) acrylate (n-arm-PEG-PCL-AC, macromer) were characterized by proton nuclear magnetic resonance and fourier transform infrared spectra. The influences of arm numbers and concentration of macromer on the properties of hydrogel were researched systematically, and the results showed that the gelation time, equilibrium swelling ratio, in vitro degradation, and drug release rate decreased with the increase of arm numbers and concentration of macromer. The degradation and drug release rate could be controlled by varying the cross-linking density of hydrogel, indicating a potential application as controlled drug delivery system. Cytotoxicity test of hydrogel extracts was conducted using L929 mouse fibroblasts, and the relative growth rate exceeded 75% (cytotoxicity type: class 1) after incubation for 24 h, showing excellent cytocompatibility. In addition, the paper presented a pH-sensitive hydrogel (G4_pH) based on 4-arm-PEG-PCL-AC and acrylic acid, and the influences of pH value on swelling behaviors and in vitro drug release of the pH-sensitive hydrogel were examined. The hydrogels shrank under acidic condition and would swell in neutral or basic medium. The pH-dependent drug release behaviors indicated a promising application of the materials as oral drug delivery vehicles.

Effect of polymer microstructure on the docetaxel release and stability of polyurethane formulation

PurSil®AL20 (PUS), a copolymer of 4,4'-dicyclohexylmethane diisocyanate (HMDI), 1,4-butane diol (BD), poly-tetramethylene oxide (PTMO) and poly-dimethyl siloxane (PDMS) was investigated for stability as a vehicle for Docetaxel (DTX) delivery through oesophageal drug eluting stent (DES). On exposure to stability test conditions, it was found that DTX release rate declined at 4 and 40 °C. In order to divulge reasons underlying this, changes in DTX solid state as well as PUS microstructure were followed. It was found that re-crystallization of DTX in PDMS rich regions was reducing the drug release at both 4 °C and 40 °C samples. So far microstructural features have not been correlated with stability and drug release, and in this study we found that at 40 °C increase in microstructural domain sizes and the inter-domain distances (from ∼85 Å to 129 Å) were responsible for hindering the DTX release in addition to DTX re-crystallization.

Thiol click modification of cyclic disulfide containing biodegradable polyurethane urea elastomers

Although the thiol click reaction is an attractive tool for postpolymerization modification of thiolmers, thiol groups are easily oxidized, limiting the potential for covalent immobilization of bioactive molecules. In this study, a series of biodegradable polyurethane elastomers incorporating stable cyclic disulfide groups was developed and characterized. These poly(ester urethane)urea (PEUU-SS) polymers were based on polycaprolactone diol (PCL), oxidized dl-dithiothreitol (O-DTT), lysine diisocyanate (LDI), or butyl diisocyanate (BDI), with chain extension by putrescine. The ratio of O-DTT:PCL was altered to investigate different levels of potential functionalization. PEG acrylate was employed to study the mechanism and availability of both bulk and surface click modification of PEUU-SS polymers. All synthesized PEUU-SS polymers were elastic with breaking strengths of 38-45 MPa, while the PEUU-SS(LDI) polymers were more amorphous, possessing lower moduli and relatively small permanent deformations versus PEUU-SS(BDI) polymers. Variable bulk click modification of PEUU-SS(LDI) polymers was achieved by controlling the amount of reduction reagent, and rapid reaction rates occurred using a one-pot, two-step process. Likewise, surface click reaction could be carried out quickly under mild, aqueous conditions. Furthermore, a maleimide-modified affinity peptide (TPS) was successfully clicked on the surface of an electrospun PEUU-SS(BDI) fibrous sheet, which improved endothelial progenitor cell adhesion versus corresponding unmodified films. The cyclic disulfide containing biodegradable polyurethanes described provide an option for cardiovascular and other soft tissue regenerative medicine applications where a temporary, elastic scaffold with designed biofunctionality from a relatively simple click chemistry approach is desired.