Electrospun PLGA nanofiber scaffolds for articular cartilage reconstruction: mechanical stability, degradation and cellular responses under mechanical stimulation in vitro

Investigating the potential of highly porous zopiclone-loaded 3D electrospun nanofibers for brain targeting via the intranasal route

Nanofibers (NFs) have proven to be very attractive tool as drug delivery plateform among the different plethora of nanosystems, owing to their unique features. They exhibit two- and three-dimensional structures some of which mimic structural environment of the body tissues, in addition to being safe, efficacious, and biocompatible drug delivery platform. Thus, this study embarked on fabricating polyvinyl alcohol/chitosan (PVA/CS) electrospun NFs encapsulating zopiclone (ZP) drug for intranasal brain targeted drug delivery. Electrospun NFs were optimized by adopting a three factor-two level full factorial design. The independent variables were: PVA/CS ratio (X1), flow rate (X2), and applied voltage (X3). The measured responses were: fiber diameter (Y1,nm), pore size (Y2,nm) and ultimate tensile strength (UTS,Y3,MPa). The selected optimum formula had resulted in NFs diameter of 215.90 ± 15.46 nm, pore size 7.12 ± 0.27 nm, and tensile strength around 6.64 ± 0.95 MPa. In-vitro biodegradability testing confirmed proper degradation of the NFs within 8 h. Moreover, swellability and breathability assessment revealed good hydrophilicity and permeability of the prepared NFs. Ex-vivo permeability study declared boosted ex-vivo permeation with an enhancement factor of 2.73 compared to ZP suspension. In addition, optimized NFs formula significantly reduced sleep latency and prolonged sleep duration in rats compared to IV ZP drug solution. These findings demonstrate the feasibility of employing the designed NFs as an effective safe platform for intranasal delivery of ZP for insomnia management.

Development of a biodegradable prosthesis through tissue engineering, for the organ-replacement or substitution of the extrahepatic bile duct

INTRODUCTION AND OBJECTIVES

There are different situations in which an extrahepatic bile duct replacement or substitute is needed, such as initial and localized stages of bile duct cancer, agenesis, stenosis, or bile duct disruption.

MATERIALS AND METHODS

A prosthesis obtained by electrospinning composed of Poly (D,L-lactide-co-glycolide) (PGLA) - Polycaprolactone (PCL) - Gelatin (Gel) was developed, mechanical and biological tests were carried out to evaluate resistance to tension, biocompatibility, biodegradability, cytotoxicity, morphological analysis and cell culture. The obtained prosthesis was placed in the extrahepatic bile duct of 15 pigs with a 2-year follow-up. Liver function tests and cholangioscopy were evaluated during follow-up.

RESULTS

Mechanical and biological evaluations indicate that this scaffold is biocompatible and biodegradable. The prosthesis implanted in the experimental model allowed cell adhesion, migration, and proliferation, maintaining bile duct permeability without altering liver function tests. Immunohistochemical analysis indicates the presence of biliary epithelium.

CONCLUSIONS

A tubular scaffold composed of electrospun PGLA-PCL-Gel nanofibers was used for the first time to replace the extrahepatic bile duct in pigs. Mechanical and biological evaluations indicate that this scaffold is biocompatible and biodegradable, making it an excellent candidate for use in bile ducts and potentially in other tissue engineering applications.

Electrospun Propolis-coated PLGA Scaffold Enhances the Osteoinduction of Mesenchymal Stem Cells

BACKGROUND

Major injuries that are caused by trauma and cancer can not be repaired through bone remodeling. The goal of bone regeneration by tissue engineering approaches is to fabricate bone implants in order to restore bone structure and functions. The use of stem cells and polymer scaffolds provides the conditions for tissue regeneration based on tissue engineering.

OBJECTIVE

This study aimed to fabricate a combined matrix of poly(lactide-co-glycolide) (PLGA) and propolis extract, which is a mixture of pollen and beeswax collected by bees from certain plants and has long been used in traditional herbal medicine, to promote the osteogenic differentiation of human adipose- derived mesenchymal stem cells (AD-MSCs).

METHODS

The scaffold was fabricated through electrospinning and was immersed in a propolis extract solution. Then, AD-MSCs were cultured and differentiated into the osteogenic lineage. The cell viability on the scaffold was evaluated by MTT assay. Osteogenic differentiation of the seeded stem cells was detected by evaluating calcium content, alkaline phosphatase (ALP) activity, and the expression of bonespecific genes.

RESULTS

The viability of cells was not affected by propolis-coated and uncoated fabricated scaffolds, while higher calcium content, ALP activity, and expression of RUNX-2, type I collagen, osteocalcin, and osteonectin were observed in cells differentiated on propolis-coated PLGA scaffold on days 7, 14, and 21 of differentiation compared to PLGA scaffold.

CONCLUSION

The results of this study showed that the presence of propolis in the scaffold could lead to better cell attachment and strengthen the osteoinduction process in stem cells.

Three-Dimensional Scaffolds for Bone Tissue Engineering

Immobilization using external or internal splints is a standard and effective procedure to treat minor skeletal fractures. In the case of major skeletal defects caused by extreme trauma, infectious diseases or tumors, the surgical implantation of a bone graft from external sources is required for a complete cure. Practical disadvantages, such as the risk of immune rejection and infection at the implant site, are high in xenografts and allografts. Currently, an autograft from the iliac crest of a patient is considered the "gold standard" method for treating large-scale skeletal defects. However, this method is not an ideal solution due to its limited availability and significant reports of morbidity in the harvest site (30%) as well as the implanted site (5-35%). Tissue-engineered bone grafts aim to create a mechanically strong, biologically viable and degradable bone graft by combining a three-dimensional porous scaffold with osteoblast or progenitor cells. The materials used for such tissue-engineered bone grafts can be broadly divided into ceramic materials (calcium phosphates) and biocompatible/bioactive synthetic polymers. This review summarizes the types of materials used to make scaffolds for cryo-preservable tissue-engineered bone grafts as well as the distinct methods adopted to create the scaffolds, including traditional scaffold fabrication methods (solvent-casting, gas-foaming, electrospinning, thermally induced phase separation) and more recent fabrication methods (fused deposition molding, stereolithography, selective laser sintering, Inkjet 3D printing, laser-assisted bioprinting and 3D bioprinting). This is followed by a short summation of the current osteochondrogenic models along with the required scaffold mechanical properties for in vivo applications. We then present a few results of the effects of freezing and thawing on the structural and mechanical integrity of PLLA scaffolds prepared by the thermally induced phase separation method and conclude this review article by summarizing the current regulatory requirements for tissue-engineered products.

Antibacterial Activity and Cytocompatibility of Electrospun PLGA Scaffolds Surface-Modified by Pulsed DC Magnetron Co-Sputtering of Copper and Titanium

Biocompatible poly(lactide-co-glycolide) scaffolds fabricated via electrospinning are having promising properties as implants for the regeneration of fast-growing tissues, which are able to degrade in the body. The hereby-presented research work investigates the surface modification of these scaffolds in order to improve antibacterial properties of this type of scaffolds, as it can increase their application possibilities in medicine. Therefore, the scaffolds were surface-modified by means of pulsed direct current magnetron co-sputtering of copper and titanium targets in an inert atmosphere of argon. In order to obtain different amounts of copper and titanium in the resulting coatings, three different surface-modified scaffold samples were produced by changing the magnetron sputtering process parameters. The success of the antibacterial properties’ improvement was tested with the methicillin-resistant bacterium Staphylococcus aureus. In addition, the resulting cell toxicity of the surface modification by copper and titanium was examined using mouse embryonic and human gingival fibroblasts. As a result, the scaffold samples surface-modified with the highest copper to titanium ratio show the best antibacterial properties and no toxicity against mouse fibroblasts, but have a toxic effect to human gingival fibroblasts. The scaffold samples with the lowest copper to titanium ratio display no antibacterial effect and toxicity. The optimal poly(lactide-co-glycolide) scaffold sample is surface-modified with a medium ratio of copper and titanium that has antibacterial properties and is non-toxic to both cell cultures.

Effect of Electrospun PLGA/Collagen Scaffolds on Cell Adhesion, Viability, and Collagen Release: Potential Applications in Tissue Engineering

The development of scaffolding obtained by electrospinning is widely used in tissue engineering due to porous and fibrous structures that can mimic the extracellular matrix. In this study, poly (lactic-co-glycolic acid) (PLGA)/collagen fibers were fabricated by electrospinning method and then evaluated in the cell adhesion and viability of human cervical carcinoma HeLa and NIH-3T3 fibroblast for potential application in tissue regeneration. Additionally, collagen release was assessed in NIH-3T3 fibroblasts. The fibrillar morphology of PLGA/collagen fibers was verified by scanning electron microscopy. The fiber diameter decreased in the fibers (PLGA/collagen) up to 0.6 µm. FT-IR spectroscopy and thermal analysis confirmed that both the electrospinning process and the blend with PLGA give structural stability to collagen. Incorporating collagen in the PLGA matrix promotes an increase in the material's rigidity, showing an increase in the elastic modulus (38%) and tensile strength (70%) compared to pure PLGA. PLGA and PLGA/collagen fibers were found to provide a suitable environment for the adhesion and growth of HeLa and NIH-3T3 cell lines as well as stimulate collagen release. We conclude that these scaffolds could be very effective as biocompatible materials for extracellular matrix regeneration, suggesting their potential applications in tissue bioengineering.

Effects of Hair Follicle Stem Cells Coupled With Polycaprolactone Scaffold on Cutaneous Wound Healing in Diabetic Male Rats

INTRODUCTION

Chronic wounds are debilitating complications of diabetes mellitus. The present study was conducted to investigate the effect of the hair follicle stem cells (HFSCs) by polycaprolactone scaffold on the healing of incisional cutaneous wounds on streptozotocin-induced diabetic male rats.

METHODS

The wound model was obtained by a biopsy punch of the skin of the animals' back. The animals were randomly divided into five groups as follows: (1) Sham (nondiabetic, not treated), (2) Control (diabetic, not treated), (3) Scaffold (diabetic, treated with polycaprolactone nanofiber scaffold), (4) HFSCs (diabetic, treated with HFSCs), and (5) Scaffold + HFSCs (diabetic, treated with combination of Scaffold and HFSCs). The wounds were photographed in the course of the treatment and their healing rate was assessed. The samples were collected from the wound sites 7, 14, and 28 d after their development. Angiogenesis was surveyed by examining messenger RNA expression and the protein synthesis levels of vascular endothelial growth factor receptor 2 (VEGFR2) and platelet/endothelial cell adhesion molecule-1/cluster of differentiation 31. The histological changes were investigated using hematoxylin and eosin and Masson's trichrome staining. Furthermore, the wound breaking strength was measured on the 28th day by tensiometry.

RESULTS

The application of the VEGFR2 as a substrate promotes the expression of CD31 in HFSCs and Scaffold + HFSCs groups compared to controls (P < 0.0001). HFSCs and scaffold also rescue the diabetes-induced dysfunction as assessed based on the parameters, such as viability, proliferation, colony formation, cellular adhesion, and chemotactic migration. HFSCs augment the levels of VEGFR2 and promote the restoration of the wound healing in diabetic groups. Furthermore, the maximum biomechanical stress significantly increased in the experimental diabetic groups (Scaffold: 1.38 ± 0.09, HFSCs: 2.13 ± 0.8, Scaffold + HFSCs: 2.38 ± 0.11) compared to the diabetes control group (1.16 ± 0.12). Using of HFSCs and scaffold on diabetic wounds leads to an accelerated wound closure, notably.

CONCLUSIONS

Thus, the current data showed that HFSCs and scaffold form excellent biomaterial in the treatment of diabetic wounds.

Nanofibrous Vildagliptin/PLGA Membranes Accelerate Diabetic Wound Healing by Angiogenesis

The inhibition of dipeptidyl peptidase-4 (DPP4) significantly enhances the wound closure rate in diabetic patients with chronic foot ulcers. DPP4 inhibitors are only prescribed for enteral, but topical administration, if feasible, to a wound would have more encouraging outcomes. Nanofibrous drug-eluting poly-D-L-lactide-glycolide (PLGA) membranes that sustainably release a high concentration of vildagliptin were prepared to accelerate wound healing in diabetes. Solutions of vildagliptin and PLGA in hexafluoroisopropanol were electrospun into nanofibrous biodegradable membranes. The concentration of the drug released in vitro from the vildagliptin-eluting PLGA membranes was evaluated, and it was found that effective bioactivity of vildagliptin can be discharged from the nanofibrous vildagliptin-eluting membranes for 30 days. Additionally, the electrospun nanofibrous PLGA membranes modified by blending with vildagliptin had smaller fiber diameters (336.0 ± 69.1 nm vs. 743.6 ± 334.3 nm, p < 0.001) and pore areas (3405 ± 1437 nm2 vs. 8826 ± 4906 nm2, p < 0.001), as well as a higher hydrophilicity value (95.2 ± 2.2° vs. 113.9 ± 4.9°, p = 0.004), and showed a better water-retention ability within 24 h compared with PLGA membranes. The vildagliptin-eluting PLGA membrane also enhanced the diabetic wound closure rate for two weeks (11.4 ± 3.0 vs. 18.7 ± 2.6 %, p < 0.001) and the level of the angiogenesis using CD31 expression (1.73 ± 0.39 vs. 0.45 ± 0.17 p = 0.006 for Western blot; 2.2 ± 0.5 vs. 0.7 ± 0.1, p < 0.001 for immunofluorescence). These results demonstrate that nanofibrous drug-eluting PLGA membranes loaded with vildagliptin are an effective agent for sustained drug release and, therefore, for accelerating cutaneous wound healing in the management of diabetic wounds.

Enhanced Diabetic Wound Healing Using Electrospun Biocompatible PLGA-Based Saxagliptin Fibrous Membranes

Delayed diabetic wound healing is an adverse event that frequently leads to limb disability or loss. A novel and promising vehicle for the treatment of diabetic wounds is required for clinical purposes. The biocompatible and resorbable poly (lactic-co-glycolic acid) (PLGA)-based fibrous membranes prepared by electrospinning that provide a sustained discharge of saxagliptin for diabetic wound healing were fabricated. The concentration of released saxagliptin in Dulbecco’s phosphate-buffered saline was analyzed for 30 days using high-performance liquid chromatography. The effectiveness of the eluted saxagliptin was identified using an endothelial progenitor cell migration assay in vitro and a diabetic wound healing in vivo. Greater hydrophilicity and water storage were shown in the saxagliptin-incorporated PLGA membranes than in the pristine PLGA membranes (both p < 0.001). For diabetic wound healing, the saxagliptin membranes accelerated the wound closure rate, the dermal thickness, and the heme oxygenase-1 level over the follicle areas compared to those in the pristine PLGA group at two weeks post-treatment. The saxagliptin group also had remarkably higher expressions of insulin-like growth factor I expression and transforming growth factor-β1 than the control group (p = 0.009 and p < 0.001, respectively) in diabetic wounds after treatment. The electrospun PLGA-based saxagliptin membranes exhibited excellent biomechanical and biological features that enhanced diabetic wound closure and increased the antioxidant activity, cellular granulation, and functionality.

Recent Applications of Electrospun Nanofibrous Scaffold in Tissue Engineering

Tissue engineering is a relatively new area of research that combines medical, biological, and engineering fundamentals to create tissue-engineered constructs that regenerate, preserve, or slightly increase the functions of tissues. To create mature tissue, the extracellular matrix should be imitated by engineered structures, allow for oxygen and nutrient transmission, and release toxins during tissue repair. Numerous recent studies have been devoted to developing three-dimensional nanostructures for tissue engineering. One of the most effective of these methods is electrospinning. Numerous nanofibrous scaffolds have been constructed over the last few decades for tissue repair and restoration. The current review gives an overview of attempts to construct nanofibrous meshes as tissue-engineered scaffolds for various tissues such as bone, cartilage, cardiovascular, and skin tissues. Also, the current article addresses the recent improvements and difficulties in tissue regeneration using electrospinning.

Prevention of peritendinous adhesions with electrospun poly (lactic acid-co-glycolic acid) (PLGA) bioabsorbable nanofiber: An experimental study

In this study, we investigated the application of poly (lactic acid-co-glycolic acid) in the rat Achilles tendon injury model for the prevention or alleviation of peritendinous adhesion and guidance of Achilles tendon regeneration. In the study, 48 rats were used and the rats were randomized by closed envelope method and divided into 4 mating groups in groups of 12. Left Achilles tendons of the non-PLGA-treated control group (groups 1 and 2) were cut and repaired. In the PLGA-treated groups (groups 3 and 4) the left Achilles tendons were cut and repaired, then PLGA bioabsorbable material was wrapped around the repair line. The rats in the 1st and 3rd groups were sacrificed at the end of the 1st month, and the rats in the 2nd and 4th groups at the end of the 2nd month. The degree of tendon adhesion in the Group 3 was lower in comparison with Group 1. Similarly, compared with Group 2, the degree of tendon adhesion in the Group 4 was lower. Inflammatory density, vascularization and fibrosis were higher in the experimental group. When the Group 3 and Group 1, and Group 2 and Group 4 were compared, adhesion length (p = 0.004, p = 0.041), adhesion characteristics (p = 0.049, p = 0.039) and adhesion severity (p = 0.007, p = 0.025) were found have statistically significant tendon healing in the PLGA-treated group, respectively. Significant difference was observed in inflammatory cell density, vascular density and fibrosis for Group 1 and Group 3, (p = 0.027, p = 0.041, p = 0.002), respectively. Similarly, significant difference was observed in inflammatory cell density, vascular density and fibrosis for Group 2 and Group 4, (p = 0.002, p = 0.027, p = 0.011), respectively. As a result, it was considered that poly (lactic acid-co-glycolic acid) material significantly reduces peritendinous adhesions, and this effect could occur with the vascular density, inflammatory density and fibrosis as indicated in histopathological examination. These data suggest that PLGA membrane has good biocompatibility and alleviates tendon adhesion after injury.

Mixed-Matrix Membrane Fabrication for Water Treatment

In recent years, technology for the fabrication of mixed-matrix membranes has received significant research interest due to the widespread use of mixed-matrix membranes (MMMs) for various separation processes, as well as biomedical applications. MMMs possess a wide range of properties, including selectivity, good permeability of desired liquid or gas, antifouling behavior, and desired mechanical strength, which makes them preferable for research nowadays. However, these properties of MMMs are due to their tailored and designed structure, which is possible due to a fabrication process with controlled fabrication parameters and a choice of appropriate materials, such as a polymer matrix with dispersed nanoparticulates based on a typical application. Therefore, several conventional fabrication methods such as a phase-inversion process, interfacial polymerization, co-casting, coating, electrospinning, etc., have been implemented for MMM preparation, and there is a drive for continuous modification of advanced, easy, and economic MMM fabrication technology for industrial-, small-, and bulk-scale production. This review focuses on different MMM fabrication processes and the importance of various parameter controls and membrane efficiency, as well as tackling membrane fouling with the use of nanomaterials in MMMs. Finally, future challenges and outlooks are highlighted.

Recent advances in PLGA-based biomaterials for bone tissue regeneration

Bone regeneration is an interdisciplinary complex lesson, including but not limited to materials science, biomechanics, immunology, and biology. Having witnessed impressive progress in the past decades in the development of bone substitutes; however, it must be said that the most suitable biomaterial for bone regeneration remains an area of intense debate. Since its discovery, poly (lactic-co-glycolic acid) (PLGA) has been widely used in bone tissue engineering due to its good biocompatibility and adjustable biodegradability. This review systematically covers the past and the most recent advances in developing PLGA-based bone regeneration materials. Taking the different application forms of PLGA-based materials as the starting point, we describe each form's specific application and its corresponding advantages and disadvantages with many examples. We focus on the progress of electrospun nanofibrous scaffolds, three-dimensional (3D) printed scaffolds, microspheres/nanoparticles, hydrogels, multiphasic scaffolds, and stents prepared by other traditional and emerging methods. Finally, we briefly discuss the current limitations and future directions of PLGA-based bone repair materials. STATEMENT OF SIGNIFICANCE: As a key synthetic biopolymer in bone tissue engineering application, the progress of PLGA-based bone substitute is impressive. In this review, we summarized the past and the most recent advances in the development of PLGA-based bone regeneration materials. According to the typical application forms and corresponding crafts of PLGA-based substitutes, we described the development of electrospinning nanofibrous scaffolds, 3D printed scaffolds, microspheres/nanoparticles, hydrogels, multiphasic scaffolds and scaffolds fabricated by other manufacturing process. Finally, we briefly discussed the current limitations and proposed the newly strategy for the design and fabrication of PLGA-based bone materials or devices.

Design, Fabrication, and Validation of a Petri Dish-Compatible PDMS Bioreactor for the Tensile Stimulation and Characterization of Microtissues

In this paper, we report on a novel biocompatible micromechanical bioreactor (actuator and sensor) designed for the in situ manipulation and characterization of live microtissues. The purpose of this study was to develop and validate an application-targeted sterile bioreactor that is accessible, inexpensive, adjustable, and easily fabricated. Our method relies on a simple polydimethylsiloxane (PDMS) molding technique for fabrication and is compatible with commonly-used laboratory equipment and materials. Our unique design includes a flexible thin membrane that allows for the transfer of an external actuation into the PDMS beam-based actuator and sensor placed inside a conventional 35 mm cell culture Petri dish. Through computational analysis followed by experimental testing, we demonstrated its functionality, accuracy, sensitivity, and tunable operating range. Through time-course testing, the actuator delivered strains of over 20% to biodegradable electrospun poly (D, L-lactide-co-glycolide) (PLGA) 85:15 non-aligned nanofibers (~91 µm thick). At the same time, the sensor was able to characterize time-course changes in Young's modulus (down to 10-150 kPa), induced by an application of isopropyl alcohol (IPA). Furthermore, the actuator delivered strains of up to 4% to PDMS monolayers (~30 µm thick), simultaneously characterizing their elastic modulus up to ~2.2 MPa. The platform repeatedly applied dynamic (0.23 Hz) tensile stimuli to live Human Dermal Fibroblast (HDF) cells for 12 hours (h) and recorded the cellular reorientation towards two angle regimes, with averages of -58.85° and +56.02°. The device biocompatibility with live cells was demonstrated for one week, with no signs of cytotoxicity. We can conclude that our PDMS bioreactor is advantageous for low-cost tissue/cell culture micromanipulation studies involving mechanical actuation and characterization. Our device eliminates the need for an expensive experimental setup for cell micromanipulation, increasing the ease of live-cell manipulation studies by providing an affordable way of conducting high-throughput experiments without the need to open the Petri dish, reducing manual handling, cross-contamination, supplies, and costs. The device design, material, and methods allow the user to define the operational range based on their targeted samples/application.

Effects of Fiber Density and Strain Rate on the Mechanical Properties of Electrospun Polycaprolactone Nanofiber Mats

This study examines the effects of electrospun polycaprolactone (PCL) fiber density and strain rate on nanofiber mat mechanical properties. An automated track collection system was employed to control fiber number per mat and promote uniform individual fiber properties regardless of the duration of collection. Fiber density is correlated to the mechanical properties of the nanofiber mats. Young's modulus was reduced as fiber density increased, from 14,901 MPa for samples electrospun for 30 s (717 fibers +/- 345) to 3,615 MPa for samples electrospun for 40 min (8,310 fibers +/- 1,904). Ultimate tensile strength (UTS) increased with increasing fiber density, where samples electrospun for 30 s resulted in a UTS of 594 MPa while samples electrospun for 40 min demonstrated a UTS of 1,250 MPa. An average toughness of 0.239 GJ/m3 was seen in the 30 s group, whereas a toughness of 0.515 GJ/m3 was observed at 40 min. The ultimate tensile strain for samples electrospun for 30 s was observed to be 0.39 and 0.48 for samples electrospun for 40 min. The relationships between UTS, Young's modulus, toughness, and ultimate tensile strain with increasing fiber density are the result of fiber-fiber interactions which leads to network mesh interactions.

Porous Silicon Nanoparticles Embedded in Poly(lactic-co-glycolic acid) Nanofiber Scaffolds Deliver Neurotrophic Payloads to Enhance Neuronal Growth

Scaffolds made from biocompatible polymers provide physical cues to direct the extension of neurites and to encourage repair of damaged nerves. The inclusion of neurotrophic payloads in these scaffolds can substantially enhance regrowth and repair processes. However, many promising neurotrophic candidates are excluded from this approach due to incompatibilities with the polymer or with the polymer processing conditions. This work provides one solution to this problem by incorporating porous silicon nanoparticles (pSiNPs) that are pre-loaded with the therapeutic into a polymer scaffold during fabrication. The nanoparticle-drug-polymer hybrids are prepared in the form of oriented poly(lactic-co-glycolic acid) nanofiber scaffolds. We test three different therapeutic payloads: bpV(HOpic), a small molecule inhibitor of phosphatase and tensin homolog (PTEN); an RNA aptamer specific to tropomyosin-related kinase receptor type B (TrkB); and the protein nerve growth factor (NGF). Each therapeutic is loaded using a loading chemistry that is optimized to slow the rate of release of these water-soluble payloads. The drug-loaded pSiNP-nanofiber hybrids release approximately half of their TrkB aptamer, bpV(HOpic), or NGF payload in 2, 10, and >40 days, respectively. The nanofiber hybrids increase neurite extension relative to drug-free control nanofibers in a dorsal root ganglion explant assay.

Electrospun Polymers in Cartilage Engineering-State of Play

Articular cartilage defects remain a clinical challenge. Articular cartilage defects progress to osteoarthritis, which negatively (e.g., remarkable pain, decreased mobility, distress) affects millions of people worldwide and is associated with excessive healthcare costs. Surgical procedures and cell-based therapies have failed to deliver a functional therapy. To this end, tissue engineering therapies provide a promise to deliver a functional cartilage substitute. Among the various scaffold fabrication technologies available, electrospinning is continuously gaining pace, as it can produce nano- to micro- fibrous scaffolds that imitate architectural features of native extracellular matrix supramolecular assemblies and can deliver variable cell populations and bioactive molecules. Herein, we comprehensively review advancements and shortfalls of various electrospun scaffolds in cartilage engineering.

Development of an Anti-Inflammatory Drug-Incorporated Biomimetic Scaffold for Corneal Tissue Engineering

Purpose: The aim of this study was to design naproxen sodium (NS)-containing, biomimetic, porous poly(lactide-co-glycolide) (PLGA) scaffolds for regeneration of damaged corneal epithelium. Methods: NS-incorporated PLGA scaffolds were prepared using the emulsion freeze-drying method and then coated with collagen or poly-l-lysine. Porosity measurements of the scaffolds were performed by the gas adsorption/desorption method and the scaffolds demonstrated highly porous, open-cellular pore structures with pore sizes from 150 to 200 μm. Results: The drug loading efficiency of scaffolds was found to be higher than 84%, and about 90%-98% of NS was released at the end of 7 days with a fast drug release rate at the initial period of time and then in a slow and sustained manner. The corneal epithelial cells were isolated from New Zealand white rabbits. The obtained cells were seeded onto scaffolds and continued to increase during the time period of the study, indicating that the scaffolds might promote corneal epithelial cell proliferation without causing toxic effects for at least 10 days. Conclusions: The NS-loaded PLGA scaffolds exhibited a combination of controlled drug release and biomimetic properties that might be attractive for use in treatment of corneal damage both for controlled release and biomedical applications.

Design and comprehensive assessment of a biomimetic tri-layer tubular scaffold via biodegradable polymers for vascular tissue engineering applications

Considering the structural complexity of the native artery wall and the limitations of current treatment strategies, developing a biomimetic tri-layer tissue-engineered vascular graft is a major developmental direction of vascular tissue regeneration. Biodegradable polymers exhibit adequate mechanical characteristics and feasible operability, showing potential prospects in the construction of tissue engineering scaffold. Herein, we present a bio-inspired tri-layer tubular graft using biodegradable polymers to simulate natural vascular architecture. The inner layer made of polycaprolactone (PCL) nanofiber possesses high tensile strength and contributed to endothelial cell adhesion and proliferation. The middle layer consisted of poly(lactic-co-glycolide) (PLGA) with a three-dimensional porous structure is appropriate for vascular smooth muscle cells (SMCs) penetration. The polyurethane (PU) was selected to be the outer layer, aiming to hold the entire tubular structure, suggesting superior mechanical properties and ideal biocompatibility. Adhesion between independent layers is achieved by thermal crosslinking. The compliance, burst pressure and suture retention force of the tubular scaffold were 2.50 ± 1.60%, 2737.73 ± 583.41 mmHg and 13.06 ± 1.89 N, respectively. The in vivo study of subcutaneous implantation for 8 weeks demonstrated the biomimetic tri-layer vascular graft could maintain intimal integrity, cell infiltration, collagen deposition and scaffold biodegradation. Overall, the biomimetic tri-layer vascular graft promises to be a potential candidate for vascular replacement and regeneration.

The Use of Nanomaterials in Tissue Engineering for Cartilage Regeneration; Current Approaches and Future Perspectives

The repair and regeneration of articular cartilage represent important challenges for orthopedic investigators and surgeons worldwide due to its avascular, aneural structure, cellular arrangement, and dense extracellular structure. Although abundant efforts have been paid to provide tissue-engineered grafts, the use of therapeutically cell-based options for repairing cartilage remains unsolved in the clinic. Merging a clinical perspective with recent progress in nanotechnology can be helpful for developing efficient cartilage replacements. Nanomaterials, < 100 nm structural elements, can control different properties of materials by collecting them at nanometric sizes. The integration of nanomaterials holds promise in developing scaffolds that better simulate the extracellular matrix (ECM) environment of cartilage to enhance the interaction of scaffold with the cells and improve the functionality of the engineered-tissue construct. This technology not only can be used for the healing of focal defects but can also be used for extensive osteoarthritic degenerative alterations in the joint. In this review paper, we will emphasize the recent investigations of articular cartilage repair/regeneration via biomaterials. Also, the application of novel technologies and materials is discussed.

Biomaterial-assisted scalable cell production for cell therapy

Cell therapy, the treatment of diseases using living cells, offers a promising clinical approach to treating refractory diseases. The global market for cell therapy is growing rapidly, and there is an increasing demand for automated methods that can produce large quantities of high quality therapeutic cells. Biomaterials can be used during cell production to establish a biomimetic microenvironment that promotes cell adhesion and proliferation while maintaining target cell genotype and phenotype. Here we review recent progress and emerging techniques in biomaterial-assisted cell production. The increasing use of auxiliary biomaterials and automated production methods provides an opportunity to improve quality control and increase production efficiency using standardized GMP-compliant procedures.

In vitro and in vivo evaluation of linezolid loaded electrospun PLGA and PLGA/PCL fiber mats for prophylaxis and treatment of MRSA induced prosthetic infections

In this study, it was aimed to formulate linezolid loaded electrospun PLGA and PCL fiber mats doing controlled drug release, to be used in the treatment and prophylaxis of the prosthesis related infections. The effect of PLGA concentration, PLGA to PCL ratio and the amount of linezolid on the fiber and mat properties were examined. Fiber diameter has been shown to increase with increasing amount of PLGA and linezolid. Increase in PLGA amount resulted in reduced linezolid release, whereas increase in linezolid amount resulted in increased drug release. All PLGA fiber mats have shown to have favorable encapsulation efficiency (≥73%) and mechanical properties. Encapsulation efficiency and the mechanical properties deteriorated with the addition of PCL to the formulations. PLGA fiber mats have shown a biphasic controlled release and in vitro antibacterial activity against methicillin-resistant Staphylococcus aureus (MRSA), pattern up to one month. The formulation selected as the optimum has been evaluated in vivo on the infected rats, which had prosthetic implantation after bone fracture. Consequently, it has been demonstrated microbiologically and histopathologically that a more efficient therapy and prophylaxis have been achieved with a 37-fold lower dose of linezolid.

Multifunctional one-dimensional polymeric nanostructures for drug delivery and biosensor applications

Advances in nanotechnology in the last decades have paved the way for significant achievements in diagnosis and treatment of various diseases. Different types of functional nanostructures have been explored and utilized as tools for addressing the challenges in detection or treatment of diseases. In particular, one-dimensional nanostructures hold great promise in theranostic applications due to their increased surface area-to-volume ratios, which allow better targeting, increased loading capacity and improved sensitivity to biomolecules. Stable polymeric nanostructures that are stimuli-responsive, biocompatible and biodegradable are especially preferred for bioapplications. In this review, different synthesis techniques of polymeric one-dimensional nanostructures are explored and functionalization methods of these nanostructures for specific applications are explained. Biosensing and drug delibiovery applications of these nanostructures are presented in detail.

Human Adipose-Derived Stem Cell Secreted Extracellular Matrix Incorporated into Electrospun Poly(Lactic-co-Glycolic Acid) Nanofibrous Dressing for Enhancing Wound Healing

Wound dressing, which prevents dehydration and provides a physical barrier against infection to wound beds, can improve wound healing. The interactions between extracellular matrix (ECM) and growth factors is critical to the healing process. Electrospun nanofibers are promising templates for wound dressings due to the structure similarity to ECM of skin. Otherwise, the ECM secreted by human adipose-derived stem cells (hASCs) is rich in growth factors known to enhance wound healing. Accordingly, we propose that the PLGA nanofibrous template incorporated with hASCs-secreted ECM may enhance wound healing. In this study, PLGA nanofibrous matrixes with an aligned or a random structure were prepared by electrospinning. Human ASCs cultured on the aligned matrix had a better viability and produced a larger amount of ECM relative to that of random one. After 7 days' cultivation, the hASCs on aligned PLGA substrates underwent decellularization to fabricate cECM/PLGA dressings. By using immunohistochemical staining against F-actin and cell nucleus, the removal of cellular components was verified. However, the type I collagen and laminin were well preserved on the cECM/PLGA nanofibrous matrixes. In addition, this substrate was hydrophilic, with appropriate mechanical strength to act as a wound dressing. The L929 fibroblasts had good activity, survival and proliferation on the cECM/PLGA meshes. In addition, the cECM/PLGA nanofibrous dressings improved the wound healing of surgically created full-thickness skin excision in a mouse model. This hASCs-secreted ECM incorporated into electrospun PLGA nanofibrous could be a promising dressing for enhancing wound healing.

The Mechanical Contribution of Vimentin to Cellular Stress Generation

Contractile stress generation by adherent cells is largely determined by the interplay of forces within their cytoskeleton. It is known that actin stress fibers, connected to focal adhesions, provide contractile stress generation, while microtubules and intermediate filaments provide cells compressive stiffness. Recent studies have shown the importance of the interplay between the stress fibers and the intermediate filament vimentin. Therefore, the effect of the interplay between the stress fibers and vimentin on stress generation was quantified in this study. We hypothesized that net stress generation comprises the stress fiber contraction combined with the vimentin resistance. We expected an increased net stress in vimentin knockout (VimKO) mouse embryonic fibroblasts (MEFs) compared to their wild-type (vimentin wild-type (VimWT)) counterparts, due to the decreased resistance against stress fiber contractility. To test this, the net stress generation by VimKO and VimWT MEFs was determined using the thin film method combined with sample-specific finite element modeling. Additionally, focal adhesion and stress fiber organization were examined via immunofluorescent staining. Net stress generation of VimKO MEFs was three-fold higher compared to VimWT MEFs. No differences in focal adhesion size or stress fiber organization and orientation were found between the two cell types. This suggests that the increased net stress generation in VimKO MEFs was caused by the absence of the resistance that vimentin provides against stress fiber contraction. Taken together, these data suggest that vimentin resists the stress fiber contractility, as hypothesized, thus indicating the importance of vimentin in regulating cellular stress generation by adherent cells.

Biomaterials and controlled release strategy for epithelial wound healing

The skin and cornea are tissues that provide protective functions. Trauma and other environmental threats often cause injuries, infections and damage to these tissues, where the degree of injury is directly correlated to the recovery time. For example, a superficial skin or corneal wound may recover within days; however, more severe injuries can last up to several months and may leave scarring. Thus, therapeutic strategies have been introduced to enhance the wound healing efficiency and quality. Although the skin and cornea share similar anatomic structures and wound healing process, therapeutic agents and formulations for skin and cornea wound healing differ in accordance with the tissue and wound type. In this review, we describe the anatomy and epithelial wound healing processes of the skin and cornea, and summarize the therapeutic molecules that are beneficial to the respective regeneration process. In addition, biomaterial scaffolds that inherently possess bioactive properties or modified with therapeutic molecules for topical controlled release and enhanced wound healing efficiency are also discussed.

Strategies to Tune Electrospun Scaffold Porosity for Effective Cell Response in Tissue Engineering

Tissue engineering aims to develop artificial human tissues by culturing cells on a scaffold in the presence of biochemical cues. Properties of scaffold such as architecture and composition highly influence the overall cell response. Electrospinning has emerged as one of the most affordable, versatile, and successful approaches to develop nonwoven nano/microscale fibrous scaffolds whose structural features resemble that of the native extracellular matrix. However, dense packing of the fibers leads to small-sized pores which obstruct cell infiltration and therefore is a major limitation for their use in tissue engineering applications. To this end, a variety of approaches have been investigated to enhance the pore properties of the electrospun scaffolds. In this review, we collect state-of-the-art modification methods and summarize them into six classes as follows: approaches focused on optimization of packing density by (a) conventional setup, (b) sequential or co-electrospinning setups, (c) involving sacrificial elements, (d) using special collectors, (e) post-production processing, and (f) other specialized methods. Overall, this review covers historical as well as latest methodologies in the field and therefore acts as a quick reference for those interested in electrospinning matrices for tissue engineering and beyond.

Nanomaterials as potential and versatile platform for next generation tissue engineering applications

Tissue engineering (TE) is an emerging field where alternate/artificial tissues or organ substitutes are implanted to mimic the functionality of damaged or injured tissues. Earlier efforts were made to develop natural, synthetic, or semisynthetic materials for skin equivalents to treat burns or skin wounds. Nowadays, many more tissues like bone, cardiac, cartilage, heart, liver, cornea, blood vessels, and so forth are being engineered using 3-D biomaterial constructs or scaffolds that could deliver active molecules such as peptides or growth factors. Nanomaterials (NMs) due to their unique mechanical, electrical, and optical properties possess significant opportunities in TE applications. Traditional TE scaffolds were based on hydrolytically degradable macroporous materials, whereas current approaches emphasize on controlling cell behaviors and tissue formation by nano-scale topography that closely mimics the natural extracellular matrix. This review article gives a comprehensive outlook of different organ specific NMs which are being used for diversified TE applications. Varieties of NMs are known to serve as biological alternatives to repair or replace a portion or whole of the nonfunctional or damaged tissue. NMs may promote greater amounts of specific interactions stimulated at the cellular level, ultimately leading to more efficient new tissue formation. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 2433-2449, 2019.

Matrix-entrapped cellular secretome rescues diabetes-induced EPC dysfunction and accelerates wound healing in diabetic mice

Cellular secretory products have infinite potential, which is only recently explored for research and therapeutic applications. The present study elaborated on the formation of a unique matrix-entrapped cellular secretome (MCS), a hydrogel-like secretome produced by bone marrow-derived mononuclear cells when cultured on a three-dimensional electrospun nanofiber matrix under specific conditions. These culture conditions support the growth of a mixed population predominantly comprising of endothelial precursor cells (EPCs), along with mesenchymal stromal cells and pericytes. Interestingly, such secretome is not formed in a pure culture of EPCs on the similarly formulated matrix, suggesting that a heterotypic cell-cell interaction is essential for the formation of MCS. In addition, the specific composition of the matrix was found to be a critical necessity for the formation of MCS. Furthermore, the application of the MCS as a substrate promotes the growth of EPCs in culture. It also rescues the diabetes-induced EPC dysfunction as assessed based on the parameters, such as viability, proliferation, colony formation, cellular adhesion, chemotactic migration, and tubule formation. MCS augments the levels of eNOS-specific mRNA (Nos3) and also promotes the restoration of the SDF1/CXCR4 axis in diabetic EPCs. Notably, a topical application of MCS on diabetic wounds leads to an accelerated wound closure. Thus, the current data showed that MCS forms an excellent cell-free biomaterial in the treatment of diabetic wounds and non-healing ulcers.

Cartilage Differentiation of Bone Marrow-Derived Mesenchymal Stem Cells in Three-Dimensional Silica Nonwoven Fabrics

In cartilage tissue engineering, three-dimensional (3D) scaffolds provide native extracellular matrix (ECM) environments that induce tissue ingrowth and ECM deposition for in vitro and in vivo tissue regeneration. In this report, we investigated 3D silica nonwoven fabrics (Cellbed®) as a scaffold for mesenchymal stem cells (MSCs) in cartilage tissue engineering applications. The unique, highly porous microstructure of 3D silica fabrics allows for immediate cell infiltration for tissue repair and orientation of cell–cell interaction. It is expected that the morphological similarity of silica fibers to that of fibrillar ECM contributes to the functionalization of cells. Human bone marrow-derived MSCs were cultured in 3D silica fabrics, and chondrogenic differentiation was induced by culture in chondrogenic differentiation medium. The characteristics of chondrogenic differentiation including cellular growth, ECM deposition of glycosaminoglycan and collagen, and gene expression were evaluated. Because of the highly interconnected network structure, stiffness, and permeability of the 3D silica fabrics, the level of chondrogenesis observed in MSCs seeded within was comparable to that observed in MSCs maintained on atelocollagen gels, which are widely used to study the chondrogenesis of MSCs in vitro and in vivo. These results indicated that 3D silica nonwoven fabrics are a promising scaffold for the regeneration of articular cartilage defects using MSCs, showing the particular importance of high elasticity.

Physiology and Engineering of the Graded Interfaces of Musculoskeletal Junctions

The connective tissues of the musculoskeletal system can be grouped into fibrous, cartilaginous, and calcified tissues. While each tissue type has a distinct composition and function, the intersections between these tissues result in the formation of complex, composite, and graded junctions. The complexity of these interfaces is a critical aspect of their healthy function, but poses a significant challenge for their repair. In this review, we describe the organization and structure of complex musculoskeletal interfaces, identify emerging technologies for engineering such structures, and outline the requirements for assessing the complex nature of these tissues in the context of recapitulating their function through tissue engineering.

Mechanical Considerations for Electrospun Nanofibers in Tendon and Ligament Repair

Electrospun nanofibers possess unique qualities such as nanodiameter, high surface area to volume ratio, biomimetic architecture, and tunable chemical and electrical properties. Numerous studies have demonstrated the potential of nanofibrous architecture to direct cell morphology, migration, and more complex biological processes such as differentiation and extracellular matrix (ECM) deposition through topographical guidance cues. These advantages have created great interest in electrospun fibers for biomedical applications, including tendon and ligament repair. Electrospun nanofibers, despite their nanoscale size, generally exhibit poor mechanical properties compared to larger conventionally manufactured polymer fiber materials. This invites the question of what role electrospun polymer nanofibers can play in tendon and ligament repair applications that have both biological and mechanical requirements. At first glance, the strength and stiffness of electrospun nanofiber grafts appear to be too low to fill the rigorous loading conditions of these tissues. However, there are a number of strategies to enhance and tune the mechanical properties of electrospun nanofiber grafts. As researchers design the next-generation electrospun tendon and ligament grafts, it is critical to consider numerous physiologically relevant mechanical criteria and to evaluate graft mechanical performance in conditions and loading environments that reflect in vivo conditions and surgical fixation methods.

Multi-length scale bioprinting towards simulating microenvironmental cues

It is envisaged that the creation of cellular environments at multiple length scales, that recapitulate in vivo bioactive and structural roles, may hold the key to creating functional, complex tissues in the laboratory. This review considers recent advances in biofabrication and bioprinting techniques across different length scales. Particular focus is placed on 3D printing of hydrogels and fabrication of biomaterial fibres that could extend the feature resolution and material functionality of soft tissue constructs. The outlook from this review discusses how one might create and simulate microenvironmental cues in vitro. A fabrication platform that integrates the competencies of different biofabrication technologies is proposed. Such a multi-process, multiscale fabrication strategy may ultimately translate engineering capability into an accessible life sciences toolkit, fulfilling its potential to deliver in vitro disease models and engineered tissue implants.

Human Amniotic Membrane with Aligned Electrospun Fiber as Scaffold for Aligned Tissue Regeneration

Fabrication of composite scaffolds is one of the strategies proposed to enhance the functionality of tissue-engineered scaffolds for improved tissue regeneration. By combining multiple elements together, unique biomimetic scaffolds with desirable physical and mechanical properties can be tailored for tissue-specific applications. Despite having a highly porous structure, the utility of electrospun fibers (EF) as scaffold is usually hampered by their insufficient mechanical strength. In this study, we attempted to produce a mechanically competent scaffold with cell-guiding ability by fabricating aligned poly lactic-co-glycolic acid (PLGA) fibers on decellularized human amniotic membrane (HAM), known to possess favorable tensile and wound healing properties. Decellularization of HAM in 18.75 μg/mL of thermolysin followed by a brief treatment in 0.25 M sodium hydroxide efficiently removed the amniotic epithelium and preserved the ultrastructure of the underlying extracellular matrix. The electrospinning of 20% (w/v) PLGA 50:50 polymer on HAM yielded beadless fibers with straight morphology. Subsequent physical characterization revealed that EF-HAM scaffold with a 3-min fabrication had the most aligned fibers with the lowest fiber diameter in comparison with EF-HAM 5- and 7-min scaffolds. Hydrated EF-HAM scaffolds with 3-min deposition had a greater tensile strength than the other scaffolds despite having thinner fibers. Nevertheless, wet HAM and EF-HAMs regardless of the fiber thicknesses had a significantly lower Young's modulus, and hence, a higher elasticity compared with dry HAM and EF-HAMs. Biocompatibility analysis showed that the viability and migration rate of skeletal muscle cells on EF-HAMs were similar to control and HAM alone. Skeletal muscle cells seeded on HAM were shown to display random orientation, whereas cells on EF-HAM scaffolds were oriented along the alignment of the electrospun PLGA fibers. In summary, besides having good mechanical strength and elasticity, EF-HAM scaffold design decorated with aligned fiber topography holds a promising potential for use in the development of aligned tissue constructs.

Tissue engineering of retina and Bruch’s membrane: a review of cells, materials and processes

The biological, structural and functional configuration of Bruch’s membrane (BM) is significantly relevant to age-related macular degeneration (AMD) and other chorioretinal diseases, and AMD is one of the leading causes of blindness in the elderly worldwide. The configuration may worsen along with the ageing of retinal pigment epithelium and BM that finally leads to AMD. Thus, the scaffold-based tissue-engineered retina provides an innovative alternative for retinal tissue repair. The cell and material requirements for retinal repair are discussed including cell sheet engineering, decellularised membrane and tissue-engineered membranes. Further, the challenges and potential in realising a whole tissue model construct for retinal regeneration are highlighted herein. This review article provides a framework for future development of tissue-engineered retina as a preclinical model and possible treatments for AMD.

Mesenchymal Stem Cells: Potential Role in the Treatment of Osteochondral Lesions of the Ankle

Given articular cartilage has a limited repair potential, untreated osteochondral lesions of the ankle can lead to debilitating symptoms and joint deterioration necessitating joint replacement. While a wide range of reparative and restorative surgical techniques have been developed to treat osteochondral lesions of the ankle, there is no consensus in the literature regarding which is the ideal treatment. Tissue engineering strategies, encompassing stem cells, somatic cells, biomaterials, and stimulatory signals (biological and mechanical), have a potentially valuable role in the treatment of osteochondral lesions. Mesenchymal stem cells (MSCs) are an attractive resource for regenerative medicine approaches, given their ability to self-renew and differentiate into multiple stromal cell types, including chondrocytes. Although MSCs have demonstrated significant promise in in vitro and in vivo preclinical studies, their success in treating osteochondral lesions of the ankle is inconsistent, necessitating further clinical trials to validate their application. This review highlights the role of MSCs in cartilage regeneration and how the application of biomaterials and stimulatory signals can enhance chondrogenesis. The current treatments for osteochondral lesions of the ankle using regenerative medicine strategies are reviewed to provide a clinical context. The challenges for cartilage regeneration, along with potential solutions and safety concerns are also discussed.

Fabrication and Use of Poly(d,l-lactide-co-glycolide)-Based Formulations Designed for Modified Release of 5-Fluorouracil

5-fluorouracil (5-FU) is a chemotherapeutic agent that has been used for the treatment of a variety of malignancies since its initial introduction to the clinic in 1957. Owing to its short biological half-life, multiple dosings are generally required to maintain effective 5-FU plasma concentrations throughout the therapeutic period. Clinical studies have shown that continuous 5-FU administration is generally superior to bolus injection as exhibited by lower toxicities and increased therapeutic efficacy. Optimal therapeutic efficacy, however, is often compromised by the limiting therapeutic index. Whilst oral formulations are also used, these suffer from the drawbacks of variable bioavailability and first-pass metabolism. As a result, sustained release formulations of 5-FU have been investigated in an effort to mimic the kinetics of continuous infusion particularly for situations where local delivery is considered appropriate. The biocompatible, biodegradable, and highly tunable synthetic polymer, poly(d,l-lactide-co-glycolide) (PLGA), is widely used as a vector for sustained drug delivery, however, issues such as insufficient loading and inappropriate burst release kinetics have dogged progress into the clinic for small hydrophilic drugs such as 5-FU. This review provides introductory information about the mechanism of action, pharmacokinetic and physicochemical properties, and clinical use of 5-FU that have contributed to the development of PLGA-based 5-FU release platforms. In addition, this review provides information on fabrication methods used for a range of 5-FU-loaded PLGA formulations and discusses factors affecting the release kinetics of 5-FU as well as the in vitro and in vivo antitumor or antiproliferative efficacy of these platforms.

On-command on/off switching of progenitor cell and cancer cell polarized motility and aligned morphology via a cytocompatible shape memory polymer scaffold

In vitro biomaterial models have enabled advances in understanding the role of extracellular matrix (ECM) architecture in the control of cell motility and polarity. Most models are, however, static and cannot mimic dynamic aspects of in vivo ECM remodeling and function. To address this limitation, we present an electrospun shape memory polymer scaffold that can change fiber alignment on command under cytocompatible conditions. Cellular response was studied using the human fibrosarcoma cell line HT-1080 and the murine mesenchymal stem cell line C3H/10T1/2. The results demonstrate successful on-command on/off switching of cell polarized motility and alignment. Decrease in fiber alignment causes a change from polarized motility along the direction of fiber alignment to non-polarized motility and from aligned to unaligned morphology, while increase in fiber alignment causes a change from non-polarized to polarized motility along the direction of fiber alignment and from unaligned to aligned morphology. In addition, the findings are consistent with the hypothesis that increased fiber alignment causes increased cell velocity, while decreased fiber alignment causes decreased cell velocity. On-command on/off switching of cell polarized motility and alignment is anticipated to enable new study of directed cell motility in tumor metastasis, in cell homing, and in tissue engineering.

Fabrication and characterization of electrospun poly lactic-co-glycolic acid/zeolite nanocomposite scaffolds using bone tissue engineering

Poly lactic- co-glycolic acid/zeolite nanocomposite scaffolds were prepared with 17 (wt%) poly lactic- co-glycolic acid (75:25) and 3, 7, and 10 (wt%) nanocrystalline zeolite particles by electrospinning poly lactic- co-glycolic acid and nanocrystalline zeolite with an average diameter of crystals equal to 42 nm. The field-emission scanning electron microscope images confirmed that fibers had no beads. In vitro mineralization in the simulated body fluid revealed that the poly lactic- co-glycolic acid/zeolite nanoscaffolds had strong bioactivity behavior and apatite crystals were formed on the scaffolds. Mechanical properties were improved in the nanocomposite scaffolds compared to the poly lactic- co-glycolic acid scaffold. Biodegradation of scaffolds was tested by being immersed and incubated in phosphate-buffered saline for 90 days, and the effect of zeolite on the degradation rate was also studied. The biological performance of nanoscaffolds and poly lactic- co-glycolic acid was assessed by in vitro culture of MG63 osteosarcoma cell line, 3-(4,5-dimethylthiazol-2-yl)-2,5-dimethiyltetrazolium-bromide assay, and 4′,6-diamidino-2-phenylindole staining. All types of scaffolds were cell compatible and could support cell proliferation. Poly lactic- co-glycolic acid/zeolite (3 and 7 (wt%)) showed cell viability and proliferation since 1, 4, and 7 days after the implantation. The cell adherence to the scaffolds was also studied by scanning electron microscope images. The results showed that MG63 cells adhered to the nanocomposites. Besides, all the results illustrated that nanocomposite scaffold with 7 (wt%) zeolite is the most suitable scaffold for bone tissue engineering.