Mechanical evaluation of five flowable resin composites by the dynamic micro-indentation method

Synthesis, Characterization and Application of Biobased Unsaturated Polyester Resin Reinforced with Unmodified/Modified Biosilica Nanoparticles

This paper presents sustainable technology for environmentally friendly composite production. Biobased unsaturated polyester resin (b-UPR), synthesized from waste polyethylene terephthalate (PET) glycosylate and renewable origin maleic anhydride (MAnh) and propylene glycol (PG), was reinforced with unmodified and vinyl-modified biosilica nanoparticles obtained from rice husk. The structural and morphological properties of the obtained particles, b-UPR, as well as composites, were characterized by Fourier-transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) techniques. The study of the influence of biosilica modification on the mechanical properties of composites was supported by hardness modeling. Improvement of the tensile strength of the b-UPR-based composite at 2.5 wt.% addition of biosilica modified with vinyl silane, named "b-UPR/SiO2-V" composite, has been achieved with 88% increase. The thermal aging process applied to the b-UPR/SiO2-V composite, which simulates use over the product's lifetime, leads to the deterioration of composites that were used as fillers in commercial unsaturated polyester resin (c-UPR). The grinded artificially aged b-UPR composites were used as filler in c-UPR for the production of a table top layer with outstanding mechanical properties, i.e., impact resistance and microhardness, as well as fire resistance rated in the V-0 category according to the UL-94 test. Developing sustainable composites that are chemically synthesized from renewable sources is important from the aspect of preserving the environment and existing resources as well as the extending their life cycle.

Surface Micro-Hardness and Wear Resistance of a Self-Adhesive Flowable Composite in Comparison to Conventional Flowable Composites

Objectives: The durability of composite restorations is directly affected by the mechanical properties of the composite. The aim of this study was to evaluate the hardness and wear resistance of self-adhesive flowable composite (SAF) in comparison with conventional flowable composites. Materials and Methods: In this in vitro study, 50 composite specimens were prepared in brass molds with 10mm ×10mm ×2mm and divided into five groups (n=10). Specimens included three conventional flowable composites (Grandio flow, Filtek flow and Admira fusion flow), one self-adhering flowable composite (SAF, Vertise flow) and a microhybrid composite (filtek z250). After polishing, the micro-hardness of the specimens was measured in a Vickers hardness device, and the specimens were then subjected to 5000, 10000, 20000, 40000, 80000 and 120000 wear cycles in a wear tester. One-way ANOVA/Games-Howell, Kruskal Wallis, and Friedman tests were used for statistical analysis. The significance level was set at P<0.05. Results: The surface micro-hardness of the SAF was significantly lower than that of the microhybrid composite (P=0.01). There was no significant difference between the surface hardness of the different tested flowable composites (P>0.05). Also, the wear resistance of the studied composites was not significantly different in various cycles (P>0.05). Conclusion: Based on our results, SAF would not be an ideal substitute for conventional flowable composites in high-stress areas.

A study on the characteristics of resin composites for provisional restorations

In this study, we evaluated the characteristics of five commercial resin composites used for provisional restorations. The inorganic filler contents of the resins were measured, and three-point bending, wear, surface hardness, water absorption, and staining tests were performed. The specimens underwent additional three-point bending tests after water storage and undergoing thermal stresses at 5°C and 55°C (10,000 cycles). Data were analyzed using one- or two-way analysis of variance and Bonferroni post-hoc tests. Pearson's correlation coefficient was used for pairwise comparisons. Each resin composite presented with different mechanical properties, based on variations in the inorganic filler content. The flexural strength of each resin composite was significantly decreased after water storage. There has a positive correlation between flexural strength and dynamic hardness but a negative correlation between flexural strength and maximum wear depth. The types and contents of the inorganic fillers, the composition of the monomer in the resin matrix, and the addition of plasticizers can affect the properties of the material.

Evaluation of the mechanical behavior of bulk-fill and conventional flowable resin composites using dynamic micro-indentation

The purpose of this research was to investigate the mechanical behavior of commercially available bulk-fill and conventional flowable resin composites using the dynamic micro-indentation method. The effect of inorganic filler content on mechanical properties was also assessed. Weight percentages of the inorganic filler in the resin composite were measured using the ashing technique. The results showed that dynamic hardness and elastic modulus tended to increase with inorganic filler content. Furthermore, the differences in mechanical properties between top and bottom surfaces were less pronounced in bulk-fill flowable resin composites compared with conventional flowable resin composites. In conclusion, the mechanical properties of bulk-fill flowable resin composites are affected by filler content. Moreover, bulk-fill flowable resin composites have a higher polymerization depth than conventional flowable resin composites when sample thickness is 4 mm.

Rheological and Mechanical Properties of Resin-Based Materials Applied in Dental Restorations

Resin-based materials have been prevalent for dental restorations over the past few decades and have been widely used for a variety of direct and indirect procedures. Typically, resin-based dental materials are required to be flowable or moldable before setting and can provide adequate mechanical strength after setting. The setting method may include, but is not limited to, light-curing, self-curing or heating. In this review, based on different indications of resin-based dental materials (e.g., dental filling composite, dental bonding agent, resin luting cement), their rheological and mechanical properties were reviewed. Viscous and flexible properties were focused on for materials before setting, while elastic properties and mechanical strength were focused on for materials after setting. At the same time, the factors that may affect their rheological and mechanical properties were discussed. It is anticipated that the insightful information and prospections of this study will be useful to the future development and fabrication of resin-based dental restorative materials.

Finite Element Analysis in Setting of Fillings of V-Shaped Tooth Defects Made with Glass-Ionomer Cement and Flowable Composite

The aim of the present paper is to investigate the deformation–stress state of fillings of V-shaped tooth defects by finite element analysis (FEA). Two different materials are used—auto-cured resin-reinforced glass-ionomer cement (GIC) and flowable photo-cured composite (FPC). Two materials are placed into the cavity in one portion, as before the application of the composite the cavity walls are covered with a thin adhesive layer. Deformations and equivalent von Mises stresses are evaluated by FEA. Experimental study of micro-leakage is performed. It is established that there is an analogous non-homogeneous distribution of equivalent Von Mises stresses at fillings of V-shaped defects, made with GIC and FPC. Maximum stresses are generated along the boundaries of the filling on the vestibular surface of the tooth and at the bottom of the filling itself. Values of equivalent Von Mises stresses of GIC fillings are higher than that of FPC. Magnitude and character of deformation distribution at GIC and FPC fillings are similar—deformation is maximum along the vestibular surface of the filling and is 0.056 and 0.053 mm, respectively. In FPC fillings, the adhesive layer, located along the cavity/filling boundary, is characterized with greatest strain. The experimental study of micro-leakage has confirmed the adequacy of models used in FEA.

Effects of polishing on surface roughness and hardness of glass-fiber-reinforced polypropylene

Removable partial dentures (RPDs) with resin-clasp retentive parts, which are known as non-metal-clasp dentures (NMCDs), have been used as alternatives for conventional RPDs with metal clasp, in case of aesthetic prosthodontic treatments. In this study, a profilometer and dynamic micro-indentation tests were used to investigate the effects of polishing on the surface properties such as surface roughness (Ra), dynamic hardness, and elastic modulus of high-rigidity glass-fiber-reinforced thermoplastics (GFRTPs) composed of E-glass fibers and polypropylene for NMCDs. The Ra values of the GFRTPs after polishing were significantly lower than those before polishing. The values were close to the Ra threshold level of 0.2, which corresponds to an acceptable surface smoothness for denture base materials. Polishing did not significantly change the dynamic hardnesses and elastic moduli of the GFRTPs. The fiber loading did not greatly affect the micromechanical properties of the GFRTPs because the glass-fiber reinforcement is embedded in the polypropylene matrix.

Fabrication and physical properties of glass-fiber-reinforced thermoplastics for non-metal-clasp dentures

Recently, non-metal-clasp dentures (NMCDs) made from thermoplastic resins such as polyamide, polyester, polycarbonate, and polypropylene have been used as removable partial dentures (RPDs). However, the use of such RPDs can seriously affect various tissues because of their low rigidity. In this study, we fabricated high-rigidity glass-fiber-reinforced thermoplastics (GFRTPs) for use in RPDs, and examined their physical properties such as apparent density, dynamic hardness, and flexural properties. GFRTPs made from E-glass fibers and polypropylene were fabricated using an injection-molding. The effects of the fiber content on the GFRTP properties were examined using glass-fiber contents of 0, 5, 10, 20, 30, 40, and 50 mass%. Commercially available denture base materials and NMCD materials were used as controls. The experimental densities of GFRTPs with various fiber contents agreed with the theoretical densities. Dynamic micro-indentation tests confirmed that the fiber content does not affect the GFRTP surface properties such as dynamic hardness and elastic modulus, because most of the reinforcing glass fibers are embedded in the polypropylene. The flexural strength increased from 55.8 to 217.6 MPa with increasing glass-fiber content from 0 to 50 mass%. The flexural modulus increased from 1.75 to 7.42 GPa with increasing glass-fiber content from 0 to 50 mass%, that is, the flexural strength and modulus of GFRTP with a fiber content of 50 mass% were 3.9 and 4.2 times, respectively, those of unreinforced polypropylene. These results suggest that fiber reinforcement has beneficial effects, and GFRTPs can be used in NMCDs because their physical properties are better than those of controls. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2254-2260, 2017.