Lung tumor promotion by chromium-containing welding particulate matter in a mouse model

Study on the soluble and insoluble fume and hexavalent chromium emitted from a new covered electrode with micro and nano sized-sodium and potassium titanate-based flux

The present study discusses the effect of the addition of nano-sized arc stabilizing materials on fume emissions and its solubility characteristics. Micro and nano-sized sodium/potassium titanates were added to the SMAW electrode flux as a substitute for the conventional sodium and potassium silicate compounds. The total and soluble metal concentration of fumes from the newly developed electrodes were estimated and compared with that of commercially available electrodes. The estimation of fume formation rate and breathing zone concentration of fumes followed the ISO 15011-1 and ISO 10882-1 standard. An average 50% reduction in the soluble fraction of fumes was observed from the electrodes containing micro-sized potassium-titanate compounds, and the reduction was further improved by 60% when nano-sodium titanate was added to the flux. Whereas, the reduction in soluble metal concentration for potassium titanate coated electrodes were 45% and 55%, in that order, for their micro and nano-structured forms. The soluble fraction of hexavalent chromium from the electrodes containing 100% nano sodium/potassium titanates was reduced up to 50% in each impactor stage. The inclusion of nano-sized sodium titanate in the flux resulted in a reduction in fume formation rate up to 55% and breathing zone concentration of fumes by 58% compared to the conventional sodium silicate coated electrodes. The electrode assaying 100% nano-potassium titanate showed a reduction of 59% in fume formation rate and 61% in breathing zone concentration compared to that of conventional potassium silicate-coated electrodes.

Lung toxicity profile of inhaled copper-nickel welding fume in A/J mice

Objective: Stainless steel welding creates fumes rich in carcinogenic metals such as chromium (Cr). Welding consumables devoid of Cr are being produced in an attempt to limit worker exposures to toxic and carcinogenic metals. The study objective was to characterize a copper-nickel (Cu-Ni) fume generated using gas metal arc welding (GMAW) and determine the pulmonary deposition and toxicity of the fume in mice exposed by inhalation. Materials and Methods: Male A/J mice (6-8 weeks of age) were exposed to air or Cu-Ni welding fumes for 2 (low deposition) or 4 (high deposition) hours/day for 10 days. Mice were sacrificed, and bronchoalveolar lavage (BAL), macrophage function, and histopathological analyses were performed at different timepoints post-exposure to evaluate resolution. Results and Discussion: Characterization of the fume indicated that most of the particles were between 0.1 and 1 µm in diameter, with a mass median aerodynamic diameter of 0.43 µm. Metal content of the fume was Cu (∼76%) and Ni (∼12%). Post-exposure, BAL macrophages had a reduced ability to phagocytose E. coli, and lung cytotoxicity was evident and significant (>12%-19% fold change). Loss of body weight was also significant at the early timepoints. Lung inflammation, the predominant finding identified by histopathology, was observed as a subacute response early that progressively resolved by 28 days with only macrophage aggregates remaining late (84 days). Conclusions: Overall, there was high acute lung toxicity with a resolution of the response in mice which suggests that the Cu-Ni fume may not be ideal for reducing toxic and inflammatory lung effects.

Janus Kinase/Signal Converters, and the Transcriptional Activator Signaling Pathway Promotes Lung Cancer Through Increasing M2 Macrophage

Accumulating evidence highlights the salient function of JAK/STAT signaling pathway in tumorigenesis and development. But the mechanism of JAK/STAT signaling in lung cancer remains elusive. This study assessed the impact of JAK/STAT on lung tumorigenesis and its interaction with microenvironment. Mouse model of primary lung cancer was established and then treated with JAK/STAT inhibitor. Immunofluorescence was performed to analyze fluorescent labels. Transwell assay determined the cell migration ability, and Western blot, immunohistochemistry, and immunofluorescence to detect the expression of JAK/STAT key proteins. Cell proliferation was measured by Kit-8 and colony formation. JAK/STAT key proteins were upregulated in lung cancer models. Inhibition of JAK/STAT led to a decrease in proliferative, migratory and invasive capability of lung cancer cells and macrophages from bone marrow and spleen. The cell invasion ability in the bone marrow and the proliferation of macrophages in the treatment group was weakened. When co-cultured with the treated macrophages, the proliferation of LLC1 cells was inhibited. Furthermore, in vitro flow cytometry indicated that JAK/STAT affected lung cancer progression by affecting the polarization of M1/M2 macrophages. Taken altogether, JAK/STAT signal enhances M2 macrophage expression and promotes lung cancer progression.

Inhibition Effect of Negative Air Ions on Adsorption between Volatile Organic Compounds and Environmental Particulate Matter

This work focused on the chemisorption of volatile organic compounds (VOCs) on particulate matter of less than 2.5 μm (PM_2.5). The detection results illustrated that VOCs on PM_2.5 containing hydroxyl, carbonyl, and ester groups and C_xH_y on PM_2.5 were sequentially decreased as 70.02, 21.35, 6.42, and 2.21%, respectively. The chemisorption mechanism showed that the stronger the electronegativity of oxygen-containing functional groups of VOCs, the easier it is to adsorb them on the silicate PM_2.5 due to hydrogen bond formation. Strong electronegative oxygen-containing functional groups readily interacted through hydrogen bonds with silanol groups, which was the main component of PM_2.5, resulting in VOC adsorption on PM_2.5. Negative air ions (NAIs) can weaken the offset ability of the lone pair of electrons in oxygen-containing functional groups in VOCs, which could significantly weaken the possibility of forming hydrogen bonds with silanol groups. Therefore, NAIs can effectively inhibit the adsorption between VOCs and PM_2.5, leading to a significant reduction in VOCs on the surface of PM_2.5.

Welding Fumes, a Risk Factor for Lung Diseases

(1) Background: Welding fumes (WFs) are composed of fine and ultrafine particles, which may reach the distal airways and represent a risk factor for respiratory diseases. (2) Methods: In vitro and in vivo studies to understand WFs pathogenesis were selected. Epidemiological studies, original articles, review, and meta-analysis to examine solely respiratory disease in welders were included. A systematic literature search, using PubMed, National Institute for Occupational Safety and Health Technical Information Center (NIOSHTIC), and Web of Science databases, was performed. (3) Results: Dose, time of exposure, and composition of WFs affect lung injury. Inflammation, lung defense suppression, oxidative stress, DNA damage, and genotoxic effects were observed after exposure both to mild and stainless steel WFs. (4) Conclusions: The detection of lung diseases associated with specific occupational exposure is crucial as complete avoidance or reduction of the exposure is difficult to achieve. Further studies in the area of particle research may aid the understanding of mechanisms involved in welding-related lung disease and to expand knowledge in welding-related cardiovascular diseases.

Activation of the IL-4/STAT6 Signaling Pathway Promotes Lung Cancer Progression by Increasing M2 Myeloid Cells

Emerging evidence shows that signal transducer and activator of transcription 6 (STAT6) plays critical roles in tumor development. We previously found high-level expression of STAT6 in human lung adenocarcinoma and squamous cell carcinoma, specifically in infiltrated immune cells located in the lung interstitium. Nevertheless, the role of STAT6 signaling in lung carcinogenesis and lung cancer proliferation and its underlying mechanisms remain unclear. This study aimed to investigate the role of STAT6 and the interaction between STAT6 and the tumor microenvironment in pulmonary tumorigenesis. We established a murine model of primary lung carcinogenesis in STAT6-deficient (STAT6^−/−) and STAT6 wild-type (WT) BALB/c mice using the carcinogen urethane. Two-month-old male mice were intraperitoneally injected with urethane (1 g/kg) dissolved in phosphate buffered saline (PBS). Primary tumors were monitored in vivo by positron emission tomography scanning. At 4, 6, and 9 months after urethane injection, lung tumors were harvested from the STAT6^−/− and WT mice for analysis. Small interfering RNA was used to downregulate the expression of STAT6 in tumor cells. Fluorescence activated cell sorting analysis was used to analyze fluorescence-conjugated cell markers. Transwell assays were used in coculturing experiments. STAT6 protein expression was detected by Western blotting, immunohistochemistry, and immunofluorescence. STAT6 mRNA expression was detected by quantitative real time-polymerase chain reaction. Cell Counting Kit-8 and colony formation assays were performed to evaluate cell proliferation. We detected high expression of STAT6 in CD11b⁺ cells of lung carcinoma. Our results indicate that STAT6 deficiency inhibits carcinogen-induced tumor growth and improves prognosis. STAT6 deficiency also decreased the mobilization and differentiation of CD11b⁺ cells. STAT6 deficiency in CD11b⁺ cells but not tumor cells decreased interleukin (IL)-4 secretion and the differentiation of CD11b⁺ cells into M2 macrophage cells. In conclusion, our findings indicate that IL-4/STAT6 signaling in CD11b⁺ cells promotes lung cancer progression by triggering an IL-4 positive feedback loop and increasing M2 myeloid cells. STAT6 may be a new therapeutic target for the prevention and treatment of lung cancer.

Mild steel welding is associated with alterations in circulating levels of cancer-related proteins

Welding fumes were recently classified as carcinogenic to humans and worldwide millions work as welders or perform welding operations. The purpose of this study was to identify new biomarkers of welding-induced carcinogenesis. We evaluated a panel of 91 putative cancer-related proteins in serum in a cohort of welders working with mild steel (n = 77) and controls (n = 94) from southern Sweden sampled on two occasions 6-year apart using a longitudinal analysis (linear mixed models). The significant results from the longitudinal analysis were tested for reproducibility in welders (n = 88) and controls (n = 69) sampled once during the same sampling period as timepoint 1 or timepoint 2 (linear regression models), i.e., in a cross-sectional setting. The models were adjusted for age, body-mass index, and use of snus. All study participants were non-smokers at recruitment. Exposure to welding fumes was assessed using questionnaires and respirable dust measurement in the breathing zone that was adjusted for personal respiratory protection equipment. The median respirable dust in welders was 0.7 (0.2-4.2) and 0.5 (0.1-1.9) mg/m³ at the first and second timepoints, respectively. We identified 14 cancer-related proteins that were differentially expressed in welders versus controls in the longitudinal analysis, out of which three were also differentially expressed in the cross-sectional analysis (cross-sectional group). Namely, syndecan 1 (SDC1), folate receptor 1 (FOLR1), and secreted protein acidic and cysteine rich (SPARC) were downregulated, in welders compared with controls. In addition, FOLR1 was negatively associated with years welding. Disease and function analysis indicated that the top proteins are related to lung cancer as well as cell invasion and migration. Our study indicates that moderate exposure to welding fumes is associated with changes in circulating levels of putative cancer-related proteins, out of which FOLR1 showed a clear dose-response relationship. It is, however, unclear to which extent these changes are adaptive or potential early biomarkers of cancer.

High variability in toxicity of welding fume nanoparticles from stainless steel in lung cells and reporter cell lines: the role of particle reactivity and solubility

Millions of people in the world perform welding as their primary occupation resulting in exposure to metal-containing nanoparticles in the fumes generated. Even though health effects including airway diseases are well-known, there is currently a lack of studies investigating how different welding set-ups and conditions affect the toxicity of generated nanoparticles of the welding fume. The aim of this study was to investigate the toxicity of nine types of welding fume particles generated via active gas shielded metal arc welding (GMAW) of chromium-containing stainless steel under different conditions and, furthermore, to correlate the toxicity to the particle characteristics. Toxicological endpoints investigated were generation of reactive oxygen species (ROS), cytotoxicity, genotoxicity and activation of ToxTracker reporter cell lines. The results clearly underline that the choice of filler material has a large influence on the toxic potential. Fume particles generated by welding with the tested flux-cored wire (FCW) were found to be more cytotoxic compared to particles generated by welding with solid wire or metal-cored wire (MCW). FCW fume particles were also the most potent in causing ROS and DNA damage and they furthermore activated reporters related to DNA double- strand breaks and p53 signaling. Interestingly, the FCW fume particles were the most soluble in PBS, releasing more chromium in the hexavalent form and manganese compared to the other fumes. These results emphasize the importance of solubility of different metal constituents of the fume particles, rather than the total metal content, for their acute toxic potential.

Concise Review of Nickel Human Health Toxicology and Ecotoxicology

Nickel (Ni) metal and Ni compounds are widely used in applications like stainless steel, alloys, and batteries. Nickel is a naturally occurring element in water, soil, air, and living organisms, and is essential to microorganisms and plants. Thus, human and environmental nickel exposures are ubiquitous. Production and use of nickel and its compounds can, however, result in additional exposures to humans and the environment. Notable human health toxicity effects identified from human and/or animal studies include respiratory cancer, non-cancer toxicity effects following inhalation, dermatitis, and reproductive effects. These effects have thresholds, with indirect genotoxic and epigenetic events underlying the threshold mode of action for nickel carcinogenicity. Differences in human toxicity potencies/potentials of different nickel chemical forms are correlated with the bioavailability of the Ni2+ ion at target sites. Likewise, Ni2+ has been demonstrated to be the toxic chemical species in the environment, and models have been developed that account for the influence of abiotic factors on the bioavailability and toxicity of Ni2+ in different habitats. Emerging issues regarding the toxicity of nickel nanoforms and metal mixtures are briefly discussed. This review is unique in its covering of both human and environmental nickel toxicity data.

Influence of welding fume metal composition on lung toxicity and tumor formation in experimental animal models

Millions of workers in the US and worldwide are exposed to complex, metal-rich welding fumes. Although welding is a crucial industrial process, the generated fumes are known to cause acute and chronic health effects when inhaled. The International Agency for Research on Cancer (IARC) classified welding fumes as carcinogenic to humans (Group 1) in 2017, based on sufficient epidemiological evidence and limited evidence in animals, an upgrade from the former Group 2B (possibly carcinogenic to humans ) classification. There is human evidence that both iron-abundant mild steel as well as chromium- and nickel-containing stainless steel welding fumes contribute to an increased risk of lung cancer. Recent animal studies show that welding fumes may act as lung tumor promoters, regardless of the presence or absence of potentially carcinogenic metals, such as chromium and nickel. The goal of this manuscript was to examine the pulmonary responses associated with welding fumes by reviewing a series of recent experimental animal studies that assessed the influence of welding fume metal composition (e.g., stainless steel versus mild steel welding fume) on markers of lung toxicity and tumor development. Additional in vivo laboratory studies are needed to further explore the association between welding and lung cancer and to help advance our understanding of a potential mechanistic link.

Pulmonary toxicity and lung tumorigenic potential of surrogate metal oxides in gas metal arc welding-stainless steel fume: Iron as a primary mediator versus chromium and nickel

In 2017, the International Agency for Research on Cancer classified welding fumes as "carcinogenic to humans" (Group 1). Both mild steel (MS) welding, where fumes lack carcinogenic chromium and nickel, and stainless steel (SS) increase lung cancer risk in welders; therefore, further research to better understand the toxicity of the individual metals is needed. The objectives were to (1) compare the pulmonary toxicity of chromium (as Cr(III) oxide [Cr2O3] and Cr (VI) calcium chromate [CaCrO4]), nickel [II] oxide (NiO), iron [III] oxide (Fe2O3), and gas metal arc welding-SS (GMAW-SS) fume; and (2) determine if these metal oxides can promote lung tumors. Lung tumor susceptible A/J mice (male, 4-5 weeks old) were exposed by oropharyngeal aspiration to vehicle, GMAW-SS fume (1.7 mg), or a low or high dose of surrogate metal oxides based on the respective weight percent of each metal in the fume: Cr2O3 + CaCrO4 (366 + 5 μg and 731 + 11 μg), NiO (141 and 281 μg), or Fe2O3 (1 and 2 mg). Bronchoalveolar lavage, histopathology, and lung/liver qPCR were done at 1, 7, 28, and 84 days post-aspiration. In a two-stage lung carcinogenesis model, mice were initiated with 3-methylcholanthrene (10 μg/g; intraperitoneal; 1x) or corn oil then exposed to metal oxides or vehicle (1 x/week for 5 weeks) by oropharyngeal aspiration. Lung tumors were counted at 30 weeks post-initiation. Results indicate the inflammatory potential of the metal oxides was Fe2O3 > Cr2O3 + CaCrO4 > NiO. Overall, the pneumotoxic effects were negligible for NiO, acute but not persistent for Cr2O3 + CaCrO4, and persistent for the Fe2O3 exposures. Fe2O3, but not Cr2O3 + CaCrO4 or NiO significantly promoted lung tumors. These results provide experimental evidence that Fe2O3 is an important mediator of welding fume toxicity and support epidemiological findings and the IARC classification.

Impact of stainless-steel welding fumes on proteins and non-coding RNAs regulating DNA damage response in the respiratory tract of Sprague-Dawley rats

Substantial evidence has established the negative impact of inhalation exposure to welding fumes on respiratory functions. The aim of the present study was to investigate the effect of welding fume inhalation on expression of molecules that function as sensors, transducers and effectors of DNA damage response (DDR) in the respiratory tract of male Sprague-Dawley rats. Animals were exposed to 50 mg/m³ stainless steel welding fumes for 1 h/d for 4, 8, and 12 weeks, respectively. Histological examination demonstrated preneoplastic changes in trachea and bronchi with focal atelectasis and accumulation of chromium (Cr) in the lungs. This was associated with elevated levels of DNA damage markers (8-oxodG, γH2AX), ATM phosphorylation, cell cycle arrest, apoptosis induction, activation of homologous recombination (HR), non-homologous end joining (NHEJ), and Nrf2 signaling, as well as altered expression of noncoding RNAs (ncRNAs). However, after 12 weeks of exposure, DDR was compromised as reflected by resumption of the cell cycle, repair inhibition, and failure of apoptosis. Data demonstrate that exposure to welding fumes influences two crucial layers of DDR regulation, phosphorylation of key proteins in NHEJ and HR, as well as the ncRNAs that epigenetically modulate DDR. Evidence indicates that marked DNA damage coupled with non-productive DNA repair and apoptosis avoidance may be involved in neoplastic transformation.

Toxicological Antagonism among Welding Fume Metals: Inactivation of Soluble Cr(VI) by Iron

Epidemiological studies in chromate production have established hexavalent chromium as a potent lung carcinogen. Inhalation of chromium(VI) most often occurs in mixtures with other metals as among stainless steel welders, which is the largest occupational group with Cr(VI) exposure. Surprisingly, carcinogenicity of Cr(VI)-containing welding fumes is moderate and not consistently higher than that of Cr-free welding. Here, we investigated interactions between chromate and three other metal ions [Fe(III), Mn(II), Ni(II)] that are typically released from stainless steel welding particles. In human lung epithelial cells with physiological levels of ascorbate and glutathione, Cr(VI) was by far the most cytotoxic metal in single exposures. Coexposure with Fe(III) suppressed cytotoxicity and genotoxicity of Cr(VI), which resulted from a severe inhibition of Cr uptake by cells and required extracellular ascorbate/glutathione. Chemically, detoxification of Cr(VI) occurred via its rapid extracellular reduction by Fe(II) that primarily originated from ascorbate-reduced Fe(III). Glutathione was a significant contributor to reduction of Cr(VI) by Fe only in the presence of ascorbate. We further found that variability in Cr(VI) metabolism among common cell culture media was caused by their different Fe content. Ni(II) and Mn(II) had no detectable effects on metabolism, cellular uptake or cytotoxicity of Cr(VI). The main biological findings were confirmed in three human lung cell lines, including stem cell-like and primary cells. We discovered extracellular detoxification of carcinogenic chromate in coexposures with Fe(III) ions and identified the underlying chemical mechanism. Our findings established an important case when exposure to mixtures causes inactivation of a potent human carcinogen.

Inhalation of iron-abundant gas metal arc welding-mild steel fume promotes lung tumors in mice

Welding fumes were reclassified as a Group 1 carcinogen by the International Agency for Research on Cancer in 2017. Gas metal arc welding (GMAW) is a process widely used in industry. Fume generated from GMAW-mild steel (MS) is abundant in iron with some manganese, while GMAW-stainless steel (SS) fume also contains significant amounts of chromium and nickel, known carcinogenic metals. It has been shown that exposure to GMAW-SS fume in A/J mice promotes lung tumors. The objective was to determine if GMAW-MS fume, which lacks known carcinogenic metals, also promotes lung tumors in mice. Male A/J mice received a single intraperitoneal injection of corn oil or the initiator 3-methylcholanthrene (MCA; 10 μg/g) and, one week later, were exposed by whole-body inhalation to GMAW-MS aerosols for 4 hours/day x 4 days/week x 8 weeks at a mean concentration of 34.5 mg/m3. Lung nodules were enumerated by gross examination at 30 weeks post-initiation. GMAW-MS fume significantly increased lung tumor multiplicity in mice initiated with MCA (21.86 ± 1.50) compared to MCA/air-exposed mice (8.34 ± 0.59). Histopathological analysis confirmed these findings and also revealed an absence of inflammation. Bronchoalveolar lavage analysis also indicated a lack of lung inflammation and toxicity after short-term inhalation exposure to GMAW-MS fume. In conclusion, this study demonstrates that inhalation of GMAW-MS fume promotes lung tumors in vivo and aligns with epidemiologic evidence that shows MS welders, despite less exposure to carcinogenic metals, are at an increased risk for lung cancer.

Silica inhalation altered telomere length and gene expression of telomere regulatory proteins in lung tissue of rats

Exposure to silica can cause lung fibrosis and cancer. Identification of molecular targets is important for the intervention and/or prevention of silica-induced lung diseases. Telomeres consist of tandem repeats of DNA sequences at the end of chromosomes, preventing chromosomal fusion and degradation. Regulator of telomere length-1 (RTEL1) and telomerase reverse transcriptase (TERT), genes involved in telomere regulation and function, play important roles in maintaining telomere integrity and length. The goal of this study was to assess the effect of silica inhalation on telomere length and the regulation of RTEL1 and TERT. Lung tissues and blood samples were collected from rats at 4, 32, and 44 wk after exposure to 15 mg/m3 of silica × 6 h/d × 5 d. Controls were exposed to air. At all-time points, RTEL1 expression was significantly decreased in lung tissue of the silica-exposed animals compared to controls. Also, significant increases in telomere length and TERT were observed in the silica group at 4 and 32 wk. Telomere length, RTEL1 and TERT expression may serve as potential biomarkers related to silica exposure and may offer insight into the molecular mechanism of silica-induced lung disease and tumorigeneses.

MiR-26a functions as a tumor suppressor in ambient particulate matter-bound metal-triggered lung cancer cell metastasis by targeting LIN28B-IL6-STAT3 axis

Exposure to ambient particulate matter (PM) has been linked to the increasing incidence and mortality of lung cancer, but the principal toxic components and molecular mechanism remain to be further elucidated. In this study, human lung adenocarcinoma A549 cells were treated with serial concentrations of water-extracted PM₁₀ (WE-PM₁₀) collected from Beijing, China. Our results showed that exposure to 25 and 50 μg/ml of WE-PM₁₀ for 48 h significantly suppressed miR-26a to upregulate lin-28 homolog B (LIN28B), and in turn activated interleukin 6 (IL6) and signal transducer and activator of transcription 3 (STAT3) in A549 cells, subsequently contributing to enhanced epithelial-mesenchymal transition and accelerated migration and invasion. In vivo pulmonary colonization assay further indicated that WE-PM₁₀ enhanced the metastatic ability of A549 cells. In addition, luciferase reporter assay demonstrated that 3' untranslated region of LIN28B was a direct target of miR-26a. Last but not the least, the key toxic contribution of metals in WE-PM₁₀ was confirmed by the finding that removal of metals through chelation significantly rescued WE-PM₁₀-mediated inflammatory, carcinogenic and metastatic responses. Taken together, miR-26a could act as the tumor suppressor in PM₁₀-related lung cancer, and PM₁₀-bound metals promoted lung cancer cell metastasis through downregulation of miR-26a that directly mediated LIN28B expression.

Inhalation of gas metal arc-stainless steel welding fume promotes lung tumorigenesis in A/J mice

Epidemiologic studies suggest an increased risk of lung cancer with exposure to welding fumes, but controlled animal studies are needed to support this association. Oropharyngeal aspiration of collected "aged" gas metal arc-stainless steel (GMA-SS) welding fume has been shown by our laboratory to promote lung tumor formation in vivo using a two-stage initiation-promotion model. Our objective in this study was to determine whether inhalation of freshly generated GMA-SS welding fume also acts as a lung tumor promoter in lung tumor-susceptible mice. Male A/J mice received intraperitoneal (IP) injections of corn oil or the chemical initiator 3-methylcholanthrene (MCA; 10 µg/g) and 1 week later were exposed by whole-body inhalation to air or GMA-SS welding aerosols for 4 h/d × 4 d/w × 9 w at a target concentration of 40 mg/m³. Lung nodules were enumerated at 30 weeks post-initiation. GMA-SS fume significantly promoted lung tumor multiplicity in A/J mice initiated with MCA (16.11 ± 1.18) compared to MCA/air-exposed mice (7.93 ± 0.82). Histopathological analysis found that the increased number of lung nodules in the MCA/GMA-SS group were hyperplasias and adenomas, which was consistent with developing lung tumorigenesis. Metal deposition analysis in the lung revealed a lower deposited dose, approximately fivefold compared to our previous aspiration study, still elicited a significant lung tumorigenic response. In conclusion, this study demonstrates that inhaling GMA-SS welding fume promotes lung tumorigenesis in vivo which is consistent with the epidemiologic studies that show welders may be at an increased risk for lung cancer.

Comment on Shvedova et al. (2016), "gender differences in murine pulmonary responses elicited by cellulose nanocrystals"

A recent publication in “Particle and Fibre Toxicology” reported on the gender differences in pulmonary toxicity from oro-pharyngeal aspiration of a high dose of cellulose nanocrystals. The study is timely given the growing interest in diverse commercial applications of cellulose nanomaterials, and the need for studies addressing pulmonary toxicity. The results from this study are interesting and can be strengthened with a discussion of how differences in the weights of female and male C57BL/6 mice was accounted for. Without such a discussion, the observed differences could be partially explained by the lower body weights of females, resulting in higher doses than males when standardized to body weight or lung volume. Further, few conclusions can be drawn about the pulmonary toxicity of cellulose nanocrystals given the study design: examination of a single high dose of cellulose nanocrystals, administered as a bolus, without positive or negative controls or low dose comparisons, and at an unphysiological and high dose rate. Simulating the bolus type delivery by inhalation would require a highly unrealistic exposure concentration in the g/m³ range of extremely short duration. A discussion of these limitations is missing in the paper; further speculative comparisons of cellulose nanocrystals toxicity to asbestos and carbon nanotubes in the abstract are both unwarranted and can be misleading, these materials were neither mentioned in the manuscript, nor evaluated in the study.

Comparison of cell counting methods in rodent pulmonary toxicity studies: automated and manual protocols and considerations for experimental design

Pulmonary toxicity studies often use bronchoalveolar lavage (BAL) to investigate potential adverse lung responses to a particulate exposure. The BAL cellular fraction is counted, using automated (i.e. Coulter Counter®), flow cytometry or manual (i.e. hemocytometer) methods, to determine inflammatory cell influx. The goal of the study was to compare the different counting methods to determine which is optimal for examining BAL cell influx after exposure by inhalation or intratracheal instillation (ITI) to different particles with varying inherent pulmonary toxicities in both rat and mouse models. General findings indicate that total BAL cell counts using the automated and manual methods tended to agree after inhalation or ITI exposure to particle samples that are relatively nontoxic or at later time points after exposure to a pneumotoxic particle when the response resolves. However, when the initial lung inflammation and cytotoxicity was high after exposure to a pneumotoxic particle, significant differences were observed when comparing cell counts from the automated, flow cytometry and manual methods. When using total BAL cell count for differential calculations from the automated method, depending on the cell diameter size range cutoff, the data suggest that the number of lung polymorphonuclear leukocytes (PMN) varies. Importantly, the automated counts, regardless of the size cutoff, still indicated a greater number of total lung PMN when compared with the manual method, which agreed more closely with flow cytometry. The results suggest that either the manual method or flow cytometry would be better suited for BAL studies where cytotoxicity is an unknown variable.

A comparison of cytotoxicity and oxidative stress from welding fumes generated with a new nickel-, copper-based consumable versus mild and stainless steel-based welding in RAW 264.7 mouse macrophages

Welding processes that generate fumes containing toxic metals, such as hexavalent chromium (Cr(VI)), manganese (Mn), and nickel (Ni), have been implicated in lung injury, inflammation, and lung tumor promotion in animal models. While federal regulations have reduced permissible worker exposure limits to Cr(VI), this is not always practical considering that welders may work in confined spaces and exhaust ventilation may be ineffective. Thus, there has been a recent initiative to minimize the potentially hazardous components in welding materials by developing new consumables containing much less Cr(VI) and Mn. A new nickel (Ni) and copper (Cu)-based material (Ni-Cu WF) is being suggested as a safer alternative to stainless steel consumables; however, its adverse cellular effects have not been studied. This study compared the cytotoxic effects of the newly developed Ni-Cu WF with two well-characterized welding fumes, collected from gas metal arc welding using mild steel (GMA-MS) or stainless steel (GMA-SS) electrodes. RAW 264.7 mouse macrophages were exposed to the three welding fumes at two doses (50 µg/ml and 250 µg/ml) for up to 24 hours. Cell viability, reactive oxygen species (ROS) production, phagocytic function, and cytokine production were examined. The GMA-MS and GMA-SS samples were found to be more reactive in terms of ROS production compared to the Ni-Cu WF. However, the fumes from this new material were more cytotoxic, inducing cell death and mitochondrial dysfunction at a lower dose. Additionally, pre-treatment with Ni-Cu WF particles impaired the ability of cells to phagocytize E. coli, suggesting macrophage dysfunction. Thus, the toxic cellular responses to welding fumes are largely due to the metal composition. The results also suggest that reducing Cr(VI) and Mn in the generated fume by increasing the concentration of other metals (e.g., Ni, Cu) may not necessarily improve welder safety.