A Ternary Magnetic Recyclable ZnO/Fe3O4/g-C3N4 Composite Photocatalyst for Efficient Photodegradation of Monoazo Dye

Fabrication of MoS2 restrained magnetic chitosan polysaccharide composite for the photocatalytic degradation of organic dyes

Chitosan (CS) polysaccharide is expected to exhibit greater ionic conductivity, which can be attributed to its increased amino group content when it is blended with different semiconducting materials. Herein, the work used this conducting ability of chitosan and prepared a heterogeneous MoS2-induced magnetic chitosan (MF@CS) composite via the co-precipitation method, which was used to scrutinize the catalytic performance with Methylene Blue (MB) and Malachite Green (MG) dyes by visible light irradiation. The saturation magnetization value of the MF@CS composite is found to be 7.8 emu/g, which is less when compared to that of pristine Fe3O4 (55.7 emu/g) particles. The bandgap of the MF@CS composite is ∼ 2.17eV, which exceeds the bandgap (Eg) of bare MoS2 of 1.80 eV. The maximum color removal of 96.3 % and 93.4 % for MB and MG dyestuffs is recognized in the exposure of the visible spectrum, respectively. At a starting dye dosage of 30 mg/L, 0.1 g/L of MF@CS, a pH level of 8-11, and 70 min of contact with direct light. The photocatalyst provides extremely good durability for a maximum of five phases. Hence, the MF@CS matrix is a viable and appropriate substance for the efficient treatment of effluents containing dye molecules.

Inhibitory effects of black phosphorus nanosheets on tumor cell proliferation through downregulation of ADIPOQ and downstream signaling pathways

Exposure to environmental pollutants, including nanomaterials, has a significant impact on tumor progression. The increased demand for black phosphorus nanosheets (BPNSs), driven by their exceptional properties, raises concerns about potential environmental contamination. Assessing their toxicity on tumor growth is essential. Herein, we employed a range of biological techniques, including cytotoxicity measurement, bioinformatics tools, proteomics, target gene overexpression, Western blot analysis, and apoptosis detection, to investigate the toxicity of BPNSs across A549, HepG-2, MCF-7, and Caco-2 cell lines. Our results demonstrated that BPNSs downregulated the expression of ADIPOQ and its associated downstream pathways, such as AMP-activated protein kinase (AMPK), nuclear factor erythroid 2-related factor 2 (Nrf2), and other unidentified pathways. These downregulated pathways ultimately led to mitochondria-dependent apoptosis. Notably, the specific downstream pathways involved varied depending on the type of tumors. These insightful findings not only confirm the consistent inhibitory effects of BPNSs across different tumor cells, but also elucidate the cytotoxicity mechanisms of BPNSs in different tumors, providing valuable information for their safe application and health risk assessment.

Advancing sustainable water treatment strategies: harnessing magnetite-based photocatalysts and techno-economic analysis for enhanced wastewater management in the context of SDGs

Herein, we explore the holistic integration of magnetite-based photocatalysts and techno-economic analysis (TEA) as a sustainable approach in wastewater treatment aligned with the Sustainable Development Goals (SDGs). While considerable attention has been devoted to photocatalytic dye degradation, the nexus between these processes and techno-economic considerations remains relatively unexplored. The review comprehensively examines the fundamental characteristics of magnetite-based photocatalysts, encompassing synthesis methods, composition, and unique properties. It investigates their efficacy in photocatalytic degradation, addressing homogeneous and heterogeneous aspects while discussing strategies to optimize photodegradation efficiency, including curbing electron-hole recombination and mitigating scavenging effects and interference by ions and humic acid. Moreover, the management aspects of magnetite-based photocatalysts are examined, focusing on their reusability and regeneration post-dye removal, along with the potential for reusing treated wastewater in relevant industrial applications. From a techno-economic perspective, the study evaluates the financial feasibility of deploying magnetite-based photocatalysts in wastewater treatment, correlating reduced pollution and the marketing of treated water with social, economic, and environmental objectives. By advocating the integration of magnetite-based photocatalysts and TEA, this paper contributes insights into scalable and profitable sustainable wastewater treatment practices. It underscores the alignment of these practices with SDGs, emphasizing a comprehensive and holistic approach to managing wastewater in ways that meet environmental, economic, and societal objectives.

Synthesis of novel nanocomposite of g-C3N4 coated ZnO-MoS2 for energy storage and photocatalytic applications

Fabrication of heterostructures for energy storage and environmental remedial applications is an interesting subject of research that has been undertaken in this present investigation. The incorporation of g-C3N4 into ZnO:MoS2 heterojunction nanocomposite was accomplished by wet-chemical route and characterized by various techniques to ascertain its structure, morphology, and study its potential electro-optical characteristics. The g-C3N4@ZnO:MoS2 sample was investigated by x-ray diffraction (XRD) which reveals the co-existence of the ZnO, MoS2 and C3N4 phases linked to characteristic crystallographic planes in the spectrum, validating the formation of ternary nanocomposite. The XRD patterns of the pristine samples were also considered as reference to understand the structural evolution and phase transformations. Field emission scanning electron microscopy (FESEM) study states the formation of heterogeneous nanostructures having nanoparticles embedded on 2-D nanosheets like structures. Studies using energy dispersive spectroscopy (EDS) and elemental mapping show that all the elements that are linked to the above hybrid nanocomposite are present. Transmission electron microscopy (TEM) provided clear insights on the microstructure as we can identify the distribution of ZnO and MoS2 nanostructures on layered g-C3N4 nanosheets. The chemical composition and oxidation states of elements were elucidated by X-ray photoelectron spectroscopy (XPS) study, which added another layer of confirmation on the structural evolution of the ternary nanocomposite. Fourier transformed infrared (FTIR) study revealed the layered structure of sp2 hybridized bonding features of C and N in g-C3N4, besides Zn-O and Mo-S stretching vibrations. The nanocomposite demonstrated improved photodegradation efficacy and decomposed alizarin red and methylene blue dyes significantly with better stability and reusability. MoS2 as a co-catalyst acts as an electron acceptor/accelerator in the Z-scheme composite photocatalysis leading to improved photocatalytic efficiency. The resulting heterostructured material delivered a higher specific capacitance of 10.85 F/g with good capacitance retention. Electrochemical study revealed the energy storage capability of the hybrid system.

ZnO/black phosphorus/C3N4 composite: An effective photocatalyst for Cr (VI) reduction and degradation of rhodamine B

The utilization of photocatalysts offers a promising approach for the removal of Cr (VI) and rhodamine dyes. Through the generation of reactive species and subsequent degradation reactions, photocatalysis provides an efficient and environmentally friendly method for the remediation of wastewater. In this study, we have synthesized an n-p-n heterojunction of carbon nitride (C3N4), zinc oxide (ZnO), and black phosphorus (BP) through the sonication-stirring method. The photocatalytic ability of this composite was examined for the decomposition rhodamine B (RhB) and detoxification of hexavalent chromium ion (up to 97% during 80 min) under Xenon irradiation. The results of trapper experiments indicated that the active species were hydroxyl radical (˙OH), electron (e-), and superoxide anion radical (˙O2-). Based on the obtained potential of the lowest unoccupied molecular orbitals (LUMO) and the highest occupied molecular orbital (HOMO) for the mentioned semiconductors, through Mutt-Schottky results, the double Z-scheme mechanism was proposed for the studied process. The electrochemical impedance spectroscopy data exhibited good charge transfer for the evaluated composite versus the pure compounds. The impressive separation of holes and electrons along with the low recombination were confirmed by the responses of photocurrent and quenching the photoluminescence (pl) intensity for the composite, respectively. The current density of the composite recorded 66.6%, 87.3%, and 92% higher than those of BP, C3N4, and ZnO, indicating an excellent electron-hole separation for the ternary composite compared to the pure semiconductors. Diffuse reflectance spectra (DRS) data revealed 2.9, 3.17, 1.15, and 2.63 eV as the band gap values for C3N4, ZnO, BP, and composite. The rate constant of the new composite to remove RhB and reduce hexavalent chromium were about 4.79 and 2.64 times higher than that of C3N4, respectively.

g-C3N4 Based Photocatalyst for the Efficient Photodegradation of Toxic Methyl Orange Dye: Recent Modifications and Future Perspectives

Industrial effluents containing dyes are the dominant pollutants, making the drinking water unfit. Among the dyes, methylene orange (MO) dye is mutagenic, carcinogenic and toxic to aquatic organisms. Therefore, its removal from water bodies through effective and economical approach is gaining increased attention in the last decades. Photocatalytic degradation has the ability to convert economically complex dye molecules into non-toxic and smaller species via redox reactions, by using photocatalysts. g-C₃N₄ is a metal-free n-type semiconductor, typical nonmetallic and non-toxici polymeric photocatalyst. It widely used in photocatalytic materials, due to its easy and simple synthesis, fascinating electronic band structure, high stability and abundant availability. As a photocatalyst, its major drawbacks are its limited efficiency in separating photo-excited electron-hole pairs, high separated charge recombination, low specific surface area, and low absorption coefficient. In this review, we report the recent modification strategies adopted for g-C₃N₄ for the efficient photodegradation of MO dye. The different modification approaches, such as nanocomposites and heterojunctions, as well as doping and defect introductions, are briefly discussed. The mechanism of the photodegradation of MO dye by g-C₃N₄ and future perspectives are discussed. This review paper will predict strategies for the fabrication of an efficient g-C₃N₄-based photocatalyst for the photodegradation of MO dye.

Photodegradation of ciprofloxacin antibiotic in water by using ZnO-doped g-C3N4 photocatalyst

Ciprofloxacin antibiotic (CIP) is one of the antibiotics with the highest rate of antibiotic resistance, if used and managed improperly, can have a negative impact on the ecosystem. In this research, ZnO modified g-C₃N₄ photocatalyst was prepared and applied for the decomposition of CIP antibiotic compounds in water. The removal performance of CIP by using ZnO/g-C₃N₄ reached 93.8% under pH 8.0 and an increasing amount of catalyst could improve the degradation performance of the pollutant. The modified ZnO/g-C₃N₄ completely oxidized CIP at a low concentration of 1 mg L^-1 and the CIP removal efficiency slightly decreases (around 13%) at a high level of pollutant (20 mg L^-1). The degradation rate of CIP by doped sample ZnO/g-C₃N₄ was 4.9 times faster than that of undoped g-C₃N₄. The doped catalyst ZnO/g-C₃N₄ also displayed high reusability for decomposition of CIP with 89.8% efficiency remaining after 3 cycles. The radical species including ·OH, ·O₂^- and h⁺ are important in the CIP degradation process. In addition, the proposed mechanism for CIP degradation by visible light-assisted ZnO/g-C₃N₄ was claimed.

Facile and green synthesis of ZnO nanoparticles for effective photocatalytic degradation of organic dyes and real textile wastewater

Remediation of organic dyes from wastewater in textile industries is a big challenge to decreasing water pollution. This study was aimed at the preparation of ZnO nanoparticles (NPs) and their application as a photocatalyst for the degradation of methylene blue (MB), sunfix red (SR) and real textile wastewater (RTW) under both UV and visible irradiations. The ZnO NPs were synthesized with a green Thymus vulgaris leaf extract-supported approach following the calcination process. 50 mg L^-1 MB and 50 mg L^-1 SR dyes were completely photodegrade under UV irradiation after only 20 and 45 minutes, respectively, in the presence of 1.0 mg/mL ZnO NPs. When they are exposed to visible light, the degradation efficiency reached 91 and 75% within 60 and 120 min, respectively. Photocatalytic measurements of RTW depict that 95% (within 60 min under UV illumination) and 79% (within 90 min under visible illumination) were degraded, respectively. The enhanced photodegradation can be attributed to the narrowing of the bandgap of the ZnO NPs, high crystallinity and nearly hexagonal morphology with an average size of 20-30 nm. The present results show that ZnO NPs could potentially be applied for high-efficiency degradation of organic dyes and RTW under both UV and visible light irradiation.

Research Progress on Graphitic Carbon Nitride/Metal Oxide Composites: Synthesis and Photocatalytic Applications

Although graphitic carbon nitride (g-C3N4) has been reported for several decades, it is still an active material at the present time owing to its amazing properties exhibited in many applications, including photocatalysis. With the rapid development of characterization techniques, in-depth exploration has been conducted to reveal and utilize the natural properties of g-C3N4 through modifications. Among these, the assembly of g-C3N4 with metal oxides is an effective strategy which can not only improve electron-hole separation efficiency by forming a polymer-inorganic heterojunction, but also compensate for the redox capabilities of g-C3N4 owing to the varied oxidation states of metal ions, enhancing its photocatalytic performance. Herein, we summarized the research progress on the synthesis of g-C3N4 and its coupling with single- or multiple-metal oxides, and its photocatalytic applications in energy production and environmental protection, including the splitting of water to hydrogen, the reduction of CO2 to valuable fuels, the degradation of organic pollutants and the disinfection of bacteria. At the end, challenges and prospects in the synthesis and photocatalytic application of g-C3N4-based composites are proposed and an outlook is given.

Integration of Mn-ZnFe2O4 with S-g-C3N4 for Boosting Spatial Charge Generation and Separation as an Efficient Photocatalyst

The disposal of dyes and organic matter into water bodies has become a significant source of pollution, posing health risks to humans worldwide. With rising water demands and dwindling supplies, these harmful compounds must be isolated from wastewater and kept out of the aquatic environment. In the research presented here, hydrothermal synthesis of manganese-doped zinc ferrites’ (Mn-ZnFe₂O₄) nanoparticles (NPs) and their nanocomposites (NCs) with sulfur-doped graphitic carbon nitride (Mn-ZnFe₂O₄/S-g-C₃N₄) are described. The samples’ morphological, structural, and bonding features were investigated using SEM, XRD, and FTIR techniques. A two-phase photocatalytic degradation study of (0.5, 1, 3, 5, 7, 9, and 11 wt.%) Mn-doped ZnFe₂O₄ NPs and Mn-ZnFe₂O₄/(10, 30, 50, 60, and 70 wt.%) S-g-C₃N₄ NCs against MB was carried out to find the photocatalyst with maximum efficiency. The 9% Mn-ZnFe₂O₄ NPs and Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs exhibited the best photocatalyst efficiency in phase one and phased two, respectively. The enhanced photocatalytic activity of the Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs could be attributed to synergistic interactions at the Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs interface that resulted in a more effective transfer and separation of photo-induced charges. Therefore, it is efficient, affordable, and ecologically secure to modify ZnFe₂O₄ by doping with Mn and homogenizing with S-g-C₃N₄. As a result, our current research suggests that the synthetic ternary hybrid Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs may be an effective photocatalytic system for degrading organic pollutants from wastewater.

Synthesis of nZnO from waste batteries by hydrometallurgical method for photocatalytic degradation of organic pollutants under visible light irradiation

Waste zinc carbon (Zn-C) batteries are generated worldwide in a large amount. They are non-rechargeable and costly to recycle. Therefore, they end up in the landfills where they create hazards for humans and for environment as well. Zn-C batteries are rich in concentration of different heavy metals so they can be subjected for the recovery of metals for the development of valuable new materials. In this study authors have proposed an easy hydrometallurgical method for the recovery of zinc from waste Zn-C batteries to synthesize nano zinc oxide (nZnO) photocatalyst. The prepared nZnO particles were irregular in shape, highly crystalline in nature with crystallite size 23.94 nm. The band gap of the photocatalyst was 3.1 eV. The photocatalytic activity of the synthesised nZnO was tested for the degradation of three organic pollutants namely; phenol, p-nitrophenol (PNP) and crystal violet dye (CV) in an aqueous solution under visible light irradiation. nZnO showed a good catalytic efficiency for the degradation of all the three pollutants, however, the crystal violet (CV) removal was best in comparison with the other pollutants, it was minimally effected by the increase in CV concentration. The maximum degradation of phenol, PNP and CV was found to be 95.03 ± 0.2%, 88.63 ± 0.1% and 97.87 ± 0.4%, respectively. The degradation data was fitted best with pseudo-first-order kinetic model. The photocatalyst was recyclable and its regeneration ability was higher for initial three cycles. The intermediate compounds formed in the process of degradation were determined by liquid chromatography and mass spectroscopy (LC-MS) analysis.

Highly Efficient Photocatalyst Fabricated from the Chemical Recycling of Iron Waste and Natural Zeolite for Super Dye Degradation

In this paper, Fe2O3 and Fe2O3-zeolite nanopowders are prepared by chemical precipitation utilizing the rusted iron waste and natural zeolite. In addition to the nanomorphologies; the chemical composition, structural parameters, and optical properties are examined using many techniques. The Fe2O3-zeolite photocatalyst showed smaller sizes and higher light absorption in visible light than Fe2O3. Both Fe2O3 and Fe2O3-zeolite are used as photocatalysts for methylene blue (MB) photodegradation under solar light. The effects of the contact time, starting MB concentration, Fe2O3-zeolite dose, and pH value on photocatalytic performance are investigated. The full photocatalytic degradation of MB dye (10 mg/L) is achieved using 75 mg of Fe2O3-zeolite under visible light after 30 s, which, to the best of our knowledge, is the highest performance yet for Fe2O3-based photocatalysts. This photocatalyst has also shown remarkable stability and recyclability. The kinetics and mechanisms of the photocatalytic process are studied. Therefore, the current work can be applied industrially as a cost-effective method for eliminating the harmful MB dye from wastewater and recycling the rusted iron wires.

Impact of piezoelectric effect on the heterogeneous visible photocatalysis of g-C3N4/Ag/ZnO tricomponent

In recent years, the piezophotocatalytic mechanism had been intensively recognized as a potential and promising route to sewage treatment. Here we report the piezoelectric effect improved heterogeneous photocatalysis of g-C₃N₄/Ag/ZnO (g-CN/A/Z) tricomponent in rhodomine B (RhB) degradation. Initially, the nanomaterials were characterized for their physico-chemical and optoelectronic properties using analytical techniques such as x-ray diffraction (XRD), scanning & transmission electron microscopes (SEM & TEM), UV-vis spectrophotometer and photoluminescence spectroscopy (PL). In addition, the photoelectrochemical activity of determining the photocurrent density and electrochemical impendence response were also been conducted. The catalytic properties of the tricomponent, g-CN/A/Z was studied with the degradation of RhB with visible photons irradiation and ultrasonication. In piezophotocatalysis, degradation up to 89% of RhB was achieved with 1.26 folds synergetic effect on par to the photocatalysis and piezocatalysis.

Recent advancements of g-C3N4-based magnetic photocatalysts towards the degradation of organic pollutants: a review

Heterogeneous photocatalysis premised on advanced oxidation processes has witnessed a broad application perspective, including water purification and environmental remediation. In particular, the graphitic carbon nitride (g-C₃N₄), an earth-abundant metal-free conjugated polymer, has acquired extensive application scope and interdisciplinary consideration owing to its outstanding structural and physicochemical properties. However, several issues such as the high recombination rate of the photo-generated electron-hole pairs, smaller specific surface area, and lower electrical conductivity curtail the catalytic efficacy of bulk g-C₃N₄. Another challenging task is separating the catalyst from the reaction medium, limiting their reusability and practical applications. Therefore, several methodologies are adopted strategically to tackle these issues. Attention is being paid, especially to the magnetic nanocomposites (NCs) based catalysts to enhance efficiency and proficient reusability property. This review summarizes the latest progress related to the design and development of magnetic g-C₃N₄-based NCs and their utilization in photocatalytic systems. The usefulness of the semiconductor heterojunctions on the catalytic activity, working mechanism, and degradation of pollutants are discussed in detail. The major challenges and prospects of using magnetic g-C₃N₄-based NCs for photocatalytic applications are highlighted in this report.

Highly efficient visible light active Cu-ZnO/S-g-C3N4 nanocomposites for efficient photocatalytic degradation of organic pollutants

The photocatalytic activity of photocatalysts is severely hampered by limited visible light harvesting and unwanted fast recombination of photogenerated e^- and h⁺. In the current study, the photocatalytic efficiency of Cu-ZnO/S-g-C₃N₄ (CZS) nanocomposites was investigated against MB dye. The composite materials were designed via chemical co-precipitation method and characterised by important analytical techniques. Distinctive heterojunctions developed between S-g-C₃N₄ and Cu-ZnO in the CZS composite were revealed by TEM. The synthesized composites exhibit a huge number of active sites, a large surface area, a smaller size and better visible light absorption. The considerable enhancement in the photocatalytic activity of CZS nanocomposites might be accredited to the decay in the e-h pair recombination rate and a red shift in the visible region, as observed by PL and optical analysis, respectively. Furthermore, the metal (Cu) doping into the S-g-C₃N₄/ZnO matrix created exemplary interfaces between ZnO and S-g-C₃N₄, and maximized the photocatalytic activity of CZS nanocomposites. In particular, CZS nanocomposites synthesized by integrating 25% S-g-C₃N₄ with 4% Cu-ZnO (CZS-25 NCs) exhibited the 100% photocatalytic degradation of MB in 60 minutes under sunlight irradiation. After six cycles, the photocatalytic stability of CZS-25 NCs was excellent. Likewise, a plausible MB degradation mechanism is proposed over CZS-25 NCs based on photoluminescence and reactive species scavenger test observation. The current research supports the design of novel composites for the photocatalytic disintegration of organic contaminants.

Bimetal (Fe/Zn) doped BiOI photocatalyst: An effective photodegradation of tetracycline and bacteria

Tetracycline (TC) is one of the most commonly used broad-spectrum antibiotics to treat the bacterial infection. TC antibiotics enter into the environment because of partial metabolism in the humans and animals, thereby increasing the environmental toxicity. Therefore, it is highly needed to treat TC antibiotics from the water system. In this aspect, the present work focus on the synthesis of Fe and Zn (bimetal) incorporated with different concentrations into the bismuth-oxy-iodide (Fe/Zn-BiOI) based photocatalyst materials. The synthesized Fe/Zn-BiOI was tested against photocatalytic degradation of TC antibiotics and bacteria. The band gap value of the synthesized Fe/Zn-BiOI was calculated ~2.19 eV. The incorporation of the Fe and Zn metals within the BiOI aided advantages that increased the reactive sites, oxygen defects, photon adsorption, production of hydroxyl radicals, and decrease the recombination rate, thereby high photo-degradation ability. The maximum degradation of ~83% was observed using Fe/Zn-BiOI-1-1 at 10 mg/L of TC antibiotics concentration. Moreover, ~98% of degradation was observed at pH~10 of the TC antibiotics. The photo-activity against bacteria of the Fe/Zn-BiOI was also determined. The data suggested that the synthesized Fe/Zn-BiOI based photocatalyst materials effectively inhibited the bacterial strains. Therefore, Fe/Zn-BiOI based photocatalyst materials might be promising materials that effectively degrade TC antibiotics as well as bacteria.

Photocatalytic oxidation of cationic dyes in single and binary solutions in presence of Zn-Cd oxides obtained from calcined LDH

In the present paper, zinc and cadmium layered double hydroxides (ZnCd-LDH) have been prepared through co-precipitation route then calcined at different temperatures. Their photocatalytic activity was determined by photodegradation of industriel toxic dyes (rhodamine B (RB) and crystal violet (CV)) in single and binary solutions illuminated with UVA or sunlight irradiation. It was found that the highest photodiscoloration efficiency was obtained for the nanomaterial heated at 700 °C (ZnCd-700). The physicochemical properties of ZnCd-LDH and ZnCd-700 were determined by PXRD, FTIR, DSC, TG/DTG, and DRS-UV-Vis. By heating the ZnCd-LDH material, some demixtion to ZnO and CdO phases occurred, corresponding to a band gap energy value of 2.93 eV for the formed zinc oxide nanoparticles. The results revealed that with 1 g·L^-1 of ZnCd-700 dose, the photodiscoloration of dyes was enhanced significantly where in single solution, it was > 83.9% and ≥ 98.0% in 90 min of UVA ilumination and sunlight, respectively. Whereas, the removal of CV and RB was > 89.7% and ≥ 98.7% in binary solution under UVA and solar irradiations, respectively. The superoxide anion radical (O₂^•-) was identified as the most influential reactive species for dyes degradation. In binary solution, the CV dye was photodiscolored faster than RB while in single solution, the result was the opposite. The re-use study of ZnCd-700 as photocatalyst showed a slight decrease of dyes discoloration varying between 1.4 and 7.1% from the second to the fourth use.

Impact of phthalocyanine structure as photosensitizer for ZnO nanophotocatalyst under natural solar irradiation

Novel composites of zinc oxide (ZnO) and copper phthalocyanines (CuTriPc and CuPc) were synthesized as efficient natural solar light photocatalysts for the photodegradation of organic wastewater pollutants. Spectroscopic and analytical measurements confirmed that both bulky triazolo copper phthalocyanine (CuTriPc) and unsubstituted planer (CuPc) were successfully coupled with ZnO nanoparticles. The synthesized nanocomposites were investigated as natural solar radiation photocatalysts toward the photodegradation of methylene blue (MB) analogue dye. The prepared CuTriPc/ZnO nanocomposite was proven to be an efficient solar light photocatalyst compared to pure ZnO and the unsubstituted CuPc/ZnO.

Ultrafast and high efficiency photodegradation of dyes under visible light by Au nanocluster-promoted Zn0.5Cd0.5S nanorods

Au nanoclusters decorated on the lateral surface of ultrathin ZCS nanorods could maximize the photocatalytic activity of ZCS by PRET mechanism. This makes it possible to use less photocatalysts to degrade more recalcitrant dyes in a short time.

A magnetically separable and recyclable g-C3N4/Fe3O4/porous ruthenium nanocatalyst for the photocatalytic degradation of water-soluble aromatic amines and azo dyes

Herein, we present the development of a visible-light-driven magnetically retrievable nanophotocatalyst made of porous ruthenium nanoparticles supported on magnetic carbon nitride (g-C₃N₄/Fe₃O₄/p-RuNP) for the facile removal/degradation of aromatic amines and azo dyes from wastewater. Aromatic amines and azo-based dyes in water bodies are highly toxic and carcinogenic even at very low concentrations and are difficult to separate because of their high solubility. Our nanocatalyst can efficiently degrade/decompose the aromatic amines and azo dyes under visible light (LED/sunlight) at room temperature and in a wide pH range (pH 5.0–9.0) without using any external chemicals. The magnetic property of the nanocatalyst facilitates its efficient and facile separation from the reaction mixture for reuse in multiple photocatalytic cycles. The nanocatalyst-based degradation of azo dyes and aromatic amines presented here is simple and convenient in terms of efficiency, energy, reusability and cost. The process also does not require any external chemicals and forms gaseous/less harmful end products.

A magnetically separable and recyclable g-C₃N₄/Fe₃O₄/porous ruthenium nanocatalyst display excellent photocatalytic degradation of water-soluble aromatic amines and azo dyes at ambient condition.

Photon-Induced Superior Antibacterial Activity of Palladium-Decorated, Magnetically Separable Fe3O4/Pd/mpg-C3N4 Nanocomposites

Three-component nanocomposites (Fe₃O₄/Pd/mpg-C₃N₄) have been systematically synthesized using a three-step solution method for the photocatalytic bacterial decontamination. The mesoporous g-C₃N₄ nanosheets (mpg-C₃N₄), which were prepared by the acid treatment, showed a great improvement in photocatalytic performance. The photoluminescence intensity of the mpg-C₃N₄ nanosheets was disclosed to drop about 60% from the value of normal g-C₃N₄ nanosheets. Decoration of mpg-C₃N₄ with palladium (Pd) nanoparticles led to the effective suppression of carrier recombination and the carrier migration to Fe₃O₄ nanoparticles. It was revealed that the three-component nanocomposites degraded 99.9% of E. coli and 99.8% of S. aureus bacterial strains within 2 h of solar light irradiation at a 100 μg/mL concentration, demonstrating their superb photocatalytic antibacterial activity. In addition, the nanocomposites could be easily separated from the bacterial cells and repeatedly used for photocatalytic bacterial degradation with good recyclability. The strong photon-induced antibacterial activity and good recyclability of the three-component nanocomposites may represent their potential as a promising antibacterial photocatalyst.

Mechanistic investigation of photocatalytic degradation of organic dyes by a novel zinc coordination polymer

Mechanistic presentation of the photocatalytic degradation of organic dye molecules by absorbing UV-vis light energy that spans the florescent compound TIPA's HOMO to LUMO band gap.