Biofilm formation on different dental restorative materials in the oral cavity

Microbial Leakage through Three Different Implant-Abutment Interfaces on Morse Taper Implants In Vitro

The objective of this study was to evaluate microbial leakage by means of genome counts, through the implant-abutment interface in dental implants with different Morse taper abutments. Fifty-six samples were prepared and divided in four groups: CMC TB (14 Cylindrical Implants-14 TiBase Abutments), CMX TB (14 Conical Implants-14 TiBase Abutments), CMX PU (14 Conical Implants-14 Universal Abutment) and CMX U (14 Tapered Implants-14 UCLA Abutments). Assemblies had their interface submerged in saliva as the contaminant. Samples were subjected either to thermomechanical cycling (2 × 106 mechanical cycles with frequency of 5 Hz and load of 120 N simultaneously with thermal cycles of 5-55 °C) or thermal cycling (5-55 °C). After cycling, the contents from the inner parts of assemblies were collected and analyzed using the Checkerboard DNA-DNA hybridization technique. Significant differences in the total genome counts were found after both thermomechanical or thermal cycling: CMX U > CMX PU > CMX TB > CMC TB. There were also significant differences in individual bacterial counts in each of the groups (p < 0.05). Irrespective of mechanical cycling, the type of abutment seems to influence not only the total microbial leakage through the interface, but also seems to significantly reflect differences considering individual target species.

Evaluation of early bacterial adhesion on CAD/CAM dental materials: an in situ study

The aim of this research was to determine if there are differences in early bacterial adhesion among CAD/CAM dental materials after 24 h exposure in the oral environment. One hundred twenty specimens were prepared according to the manufacturer's recommendations and divided into six groups: RBC (resin-based composite), PMMA (polymethyl methacrylate), PEEK (polyether ether ketone), ZP (zirconia polished), ZG (zirconia glazed), and cobalt-chromium alloy (CoCr alloy). Twenty healthy participants were instructed to carry an intraoral device with six specimens, one per group, for 24 h. Thereafter, real-time polymerase chain reaction (qPCR) and scanning electron microscopy (SEM) analyses enabled quantification and 2D view of biofilm formed on the specimens' surfaces. Kruskal-Wallis test and Dunn's post hoc analysis were used for inter-group comparison and data were presented as median (minimum-maximum). RBC specimens accumulated less bacteria, in comparison with ZG (p = 0.017) and PEEK specimens (p = 0.030), that dominated with the highest amount of adhered bacterial biofilm. PMMA, CoCr, and ZP specimens adhered more bacteria than RBC (p > 0.05), and less than ZG (p > 0.05) and PEEK (p > 0.05). The bacterial number varied considerably among participants. The obtained results enable a closer view into the susceptibility of CAD/CAM materials to microorganisms during the presence in the oral environment, which can be beneficial for a proper selection of these materials for a variety of dental restorations.

Investigating the association between nitrate dosing and nitrite generation by the human oral microbiota in continuous culture

The generation of nitrite by the oral microbiota is believed to contribute to healthy cardiovascular function, with oral nitrate reduction to nitrite associated with systemic blood pressure regulation. There is the potential to manipulate the composition or activities of the oral microbiota to a higher nitrate-reducing state through nitrate supplementation. The current study examined microbial community composition and enzymatic responses to nitrate supplementation in sessile oral microbiota grown in continuous culture. Nitrate reductase (NaR) activity and nitrite concentrations were not significantly different to tongue-derived inocula in model biofilms. These were generally dominated by Streptococcus spp., initially, and a single nitrate supplementation resulted in the increased relative abundance of the nitrate-reducing genera Veillonella, Neisseria, and Proteus spp. Nitrite concentrations increased concomitantly and continued to increase throughout oral microbiota development. Continuous nitrate supplementation, over a 7-day period, was similarly associated with an elevated abundance of nitrate-reducing taxa and increased nitrite concentration in the perfusate. In experiments in which the models were established in continuous low or high nitrate environments, there was an initial elevation in nitrate reductase, and nitrite concentrations reached a relatively constant concentration over time similar to the acute nitrate challenge with a similar expansion of Veillonella and Neisseria. In summary, we have investigated nitrate metabolism in continuous culture oral biofilms, showing that nitrate addition increases nitrate reductase activity and nitrite concentrations in oral microbiota with the expansion of putatively NaR-producing taxa.IMPORTANCEClinical evidence suggests that blood pressure regulation can be promoted by nitrite generated through the reduction of supplemental dietary nitrate by the oral microbiota. We have utilized oral microbiota models to investigate the mechanisms responsible, demonstrating that nitrate addition increases nitrate reductase activity and nitrite concentrations in oral microbiota with the expansion of nitrate-reducing taxa.

Biofilm Formation on Hybrid, Resin-Based CAD/CAM Materials for Indirect Restorations: A Comprehensive Review

Hybrid materials are a recent addition in the field of restorative dentistry for computer-aided design/computer-aided manufacturing (CAD/CAM) indirect restorations. The long-term clinical success of modern dental restorative materials is influenced by multiple factors. Among the characteristics affecting the longevity of a restoration, the mechanical properties and physicοchemical interactions are of utmost importance. While numerous researchers constantly evaluate mechanical properties, the biological background of resin-based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze biofilm formation on the surfaces of novel, hybrid, resin-based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence initial bacterial adhesion; however, most studies focus on in vitro protocols, and in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing an accurate understanding of the bioadhesion phenomenon in the oral cavity.

Antibacterial Agents for Composite Resin Restorative Materials: Current Knowledge and Future Prospects

Resin composites became the material of choice for direct restorations in anterior and posterior teeth. Despite the revolutionary improvement in the material, restoration failure is still a major drawback due to the material's inherent negative properties, including a lack of antibacterial effects. Therefore, many attempts have been made to incorporate antibacterial agents into resin composite materials to improve their antimicrobial properties and prevent secondary caries formation. Multiple laboratory studies have been conducted using different antibacterial agents, such as quaternary ammonium compounds, methacryloyloxydodecylpyridinium bromide, magnesium oxide nanoparticles, chlorhexidine, and chitosan. This review provides a glance at the current status of these materials and the research directions needed in the future.

Antimicrobial activity, surface properties, and cytotoxicity of microencapsulated phytochemicals incorporated into three-dimensionally printable dental polymers

OBJECTIVES

This study aimed to investigate the antimicrobial properties of three dimensionally-printed dental polymers (3DPs) incorporated with microencapsulated phytochemicals (MPs) and to assess their surface characteristics and cytotoxicity.

METHODS

MPs derived from phytoncide oil and their specific chemical components were introduced into suspensions of three microbial species: Streptococcus gordonii, Streptococcus oralis, and Candida albicans. Optical density was measured to determine the microbial growth in the presence of MPs for testing their antimicrobial activity. MPs at 5% (w/w) were mixed with dental polymers and dispersants to 3DP discs. These microbial species were then seeded onto the discs and incubated for 24 h. The antibacterial and antifungal activities of MP-containing 3DPs were evaluated by counting the colony-forming units (n = 3). The biofilm formation on the 3DP was assessed by crystal violet staining assay (n = 3). Microbial viability was determined using a live-dead staining and CLSM observation (n = 3). Surface roughness and water contact angle were assessed (n = 10). Cytotoxicity of MP-containing 3DPs for human gingival fibroblast was evaluated by MTT assay.

RESULTS

MPs, particularly (-)-α-pinene, suppressed the growth of all tested microbial species. MP-containing 3DPs significantly reduced the colony count (P ≤ 0.001) and biofilm formation (P ≤ 0.009), of all tested microbial species. Both surface roughness (P < 0.001) and water contact angle (P < 0.001) increased. The cytotoxicity remained unchanged after incorporating MPs to the 3DPs (P = 0.310).

CONCLUSIONS

MPs effectively controlled the microbial growth on 3DPs as evidenced by the colony count, biofilm formation, and cell viability. Although MPs modified the surface characteristics, they did not influence the cytotoxicity of 3DPs.

CLINICAL SIGNIFICANCE

Integration of MPs into 3DPs could produce dental prostheses or appliances with antimicrobial properties. This approach not only provides a proactive solution to reduce the risk of oral biofilm-related infection but also ensures the safety and biocompatibility of the material, thereby improving dental care.

Co-occurrence of dental caries and periodontitis: multilevel modelling approach

BACKGROUND

Previous studies reported varyingly positive, negative, or no relationships between caries and periodontitis. Therefore, the aim was to assess the potential co-occurrence of caries experience and periodontal inflammation on the same teeth.

METHODS

This cross-sectional study used data from the Lithuanian National Oral Health Survey. The study included a stratified random sample of 1405 individuals aged 34-78, recruited from 5 Lithuanian cities and 10 peri-urban/rural areas (response rate 52%). Information about sociodemographic (age, sex, education, residence), behavioral (sugar-containing diet, tooth brushing frequency, use of interdental care products, last dental visit, smoking) and biological (systemic disease, use of medication and xerostomia) determinants was collected using the World Health Organization (WHO) Oral Health Questionnaire for Adults supplemented with additional questions. Clinical data were recorded using the WHO criteria and collected by one trained and calibrated examiner. Dental caries status was recorded as sound, decayed, missing, filled surfaces. Subsequently for the analyses, status was recorded at a tooth-level as decayed- and filled-teeth (DT and FT) including proximal, buccal, and oral surfaces. Two measures were used for periodontal status. The probing pocket depth (PPD) was measured at six sites and recorded at a tooth level into the absence of PPD or presence of PPD ≥ 4 mm. Bleeding on probing (BOP) was measured at the same six sites and was recorded as either present or absent at a tooth-level. Univariable and multivariable 2-level random intercept binary logistic regression analyses were utilized.

RESULTS

Positive associations were found between DT and BOP (OR 1.42, 95% CI 1.20-1.67), FT and BOP (OR 2.07, 95% CI 1.82-2.23), DT and PPD (OR 1.38, 95% CI 1.15-1.67) and FT and PPD (OR 2.01, 95% CI 1.83-2.20).

CONCLUSIONS

Our findings add evidence for the co-occurrence of periodontal inflammation and caries on the same teeth. This suggests the need for increased emphasis on a transdisciplinary approach in designing oral health interventions that target dental caries and periodontal disease simultaneously. In addition, longitudinal studies exploring the co-occurrence of caries and periodontal disease at the same sites, taking into consideration the levels of both conditions and genetic variation, are warranted.

Cryptocarya moschata extract decreases single and mixed biofilms on acrylic resins

OBJECTIVE

This study proposed to assess the effect of Cryptocarya moschata extract on single and mixed biofilms formed on denture base and reline acrylic resin.

MATERIALS AND METHODS

Single and mixed biofilms of Candida albicans and Streptococcus mutans were formed on the samples and treated with C. moschata extract; Nystatin solution at 100,000 IU/mL or Penicillin antibiotic solution at 100,000 IU/mL; or PBS solution. Antimicrobial activity was analyzed by counting colony-forming units, metabolism assay, assessment of protein components of the biofilm matrix, and of cell viability using confocal laser scanning microscopy (CLSM). Data were submitted to ANOVA and Tukey's post-test (α = 0.05).

RESULTS

Cryptocarya moschata extract reduced cell viability of C. albicans and S. mutans single and mixed biofilms formed on samples. For all types of biofilms in the C. moschata group, there was a log reduction of the biofilm, proven by the Alamar Blue assay. Analyzing the extracellular matrix protein components, groups treated with the extract exhibited a lower level of fluorescence compared to the PBS groups. Reduction in thickness biofilm and viable cells was perceptible in the C. moschata group when assessing through CLSM.

CONCLUSION

Cryptocarya moschata extract reduced the single and mixed biofilms of C. albicans and S. mutans on acrylic resins.

Interaction between microorganisms and dental material surfaces: general concepts and research progress

Bacterial adhesion to dental materials’ surfaces is the initial cause of dental materials-related infections. Therefore, inhibiting bacterial adhesion is a critical step in preventing and controlling these infections. To this end, it is important to know how the properties of dental materials affect the interactions between microorganisms and material surfaces to produce materials without biological contamination. This manuscript reviews the mechanism of bacterial adhesion to dental materials, the relationships between their surface properties and bacterial adhesion, and the impact of bacterial adhesion on their surface properties. In addition, this paper summarizes how these surface properties impact oral biofilm formation and proposes designing intelligent dental material surfaces that can reduce biological contamination.

Long-term application of silver nanoparticles in dental restoration materials: potential toxic injury to the CNS

Silver nanoparticles (AgNPs) have durable and remarkable antimicrobial effects on pathogenic microorganisms, such as bacteria and fungi, in dental plaques. As such, they are widely added to dental restoration materials, including composite resins, denture bases, adhesives, and implants, to solve the problems of denture stomatitis, peri-implant inflammation, and oral infection caused by the long-term use of these dental restoration materials. However, AgNPs can be absorbed into the blood circulatory system through the nasal/oral mucosa, lungs, gastrointestinal tract, skin, and other pathways and then distributed into the lungs, kidneys, liver, spleen, and testes, thereby causing toxic injury to these tissues and organs. It can even be transported across the blood-brain barrier (BBB) and continuously accumulate in brain tissues, causing injury and dysfunction of neurons and glial cells; consequently, neurotoxicity occurs. Other nanomaterials with antibacterial or remineralization properties are added to dental restoration materials with AgNPs. However, studies have yet to reveal the neurotoxicity caused by dental restoration materials containing AgNPs. In this review, we summarize the application of AgNPs in dental restoration materials, the mechanism of AgNPs in cytotoxicity and toxic injury to the BBB, and the related research on the accumulation of AgNPs to cause changes of neurotoxicity. We also discuss the mechanisms of neurotoxicity caused by AgNPs and the mode and rate of AgNPs released from dental restorative materials added with AgNPs to evaluate the probability of neurotoxic injury to the central nervous system (CNS), and then provide a theoretical basis for developing new composite dental restoration materials. Mechanism of neurotoxicity caused by AgNPs: AgNPs in the blood circulation enter the brain tissue after being transported across the BBB through transendothelial cell pathway and paracellular transport pathway, and continuously accumulate in brain tissue, causing damage and dysfunction of neurons and glial cells which ultimately leads to neurotoxicity. The uptake of AgNPs by neurons, astrocytes and microglia causes damage to these cells. AgNPs with non-neurotoxic level often increases the secretion of a variety of cytokines, up-regulates the expression of metallothionein in glial cells, even up-regulates autophagy and inflammation response to protect neurons from the toxic damage of AgNPs. However, the protective effect of glial cells induced by AgNPs exposure to neurotoxic levels is insufficient, which leads to neuronal damage and dysfunction and even neuronal programmed cell death, eventually cause neurotoxicity.

Application of Three Compounds Extracted from Cynodon dactylon against Streptococcus mutans Biofilm Formation to Prevent Oral Diseases

Streptococcus mutans bacteria form a biofilm called plaque that causes oral diseases, including tooth decay. Therefore, inhibition of biofilm formation is essential to maintaining good oral health. The health and nutritional benefits of Cynodon dactylon are well documented, but very little is known about its use to treat against oral diseases. The aim of this study was to detect the adhesion strength of the S. mutans bacterial biofilm in 100 cases in the Rajshahi region and evaluate the inhibitory activity of different compound extracts of C. dactylon on the S. mutans bacterial biofilm by determining the composition of isolated compounds using phytochemical analysis. Nuclear magnetic resonance (NMR) spectroscopy confirmed that three specific compounds from C. dactylon were discovered in this study: 3,7,11,15 tetramethyl hexadec-2-4dien 1-o1, compound 3,7,11,15 tetramethylhexadec-2-en-1-o1 from phytol derivatives, and stigmasterol. Results indicated that the compound of 3,7,11,15-tetramethyl-hexadec-2-en-1-ol exhibited higher antibiofilm activities on S. mutans than those of the other compound extracts. A lower level of minimum inhibitory concentration was exposed by 3, 7, 11,15 tetramethyl hexadeca-2-en-1-o1 (T2) on S. mutans at 12.5 mL. In this case, the compound of 3,7,11,15 tetramethyl hexadec 2en-1-o1 was used, and patients showed a mean value and standard error reduced from 3.42 ± 0.21 to 0.33 ± 0.06 nm. The maximum inhibition was (80.10%) in the case of patient no. 17, with a value of p < 0.05 found for S. mutans to which 12.5 μL/mL ethyl acetate extract was applied. From these findings, it may be concluded that C. dactylon extracts can be incorporated into various oral preparations to prevent tooth decay.

Is microbial adhesion affected by the build orientation of a 3-dimensionally printed denture base resin?

STATEMENT OF PROBLEM

How the build orientation of a 3-dimensionally (3D) printed denture affects microbial adhesion is unclear.

PURPOSE

The purpose of this in vitro study was to compare the adherence of Streptococcus spp. and Candida spp. on 3D-printed denture bases prepared at different build orientations with conventional heat-polymerized resin.

MATERIAL AND METHODS

Resin specimens (n=5) with standardized 28.3 mm² surface area were 3D printed at 0 and 60 degrees, and heat-polymerized (3DP-0, 3DP-60, and HP, respectively). The specimens were placed in a Nordini artificial mouth (NAM) model and exposed to 2 mL of clarified whole saliva to create a pellicle-coated substratum. Suspensions of Streptococcus mitis and Streptococcus sanguinis, Candida albicans and Candida glabrata, and a mixed species, each at 10⁸ cfu/mL were pumped separately into the model for 24 hours to promote microbial adhesion. The resin specimens were then removed, placed in fresh media, and sonicated to dislodge attached microbes. Each suspension (100 μL) was aliquoted and spread on agar plates for colony counting. The resin specimens were also examined under a scanning electron microscope. The interaction between types of specimen and groups of microbes was examined with 2-way ANOVA and then further analysis with Tukey honest significant test and Kruskal-Wallis post hoc tests (α=.05).

RESULTS

A significant interaction was observed between the 3DP-0, 3DP-60, and HP specimen types and the groups of microbes adhering to the corresponding denture resin specimens (P<.05). The difference was statistically significant among 3DP-0, 3DP-60, and HP specimens (P<.05). The adherence of candida was 3.98-times lower on the 3DP-0 than that of HP (P<.05). However, adherence of the mixed-species microbes and streptococci on the 3DP-60 were 1.75 times and 2-fold higher, respectively (P<.05). The scanning electron micrographs showed that 3DP-0 exhibited the lowest microbial adherence compared with HP and 3DP-60.

CONCLUSIONS

Adherence affinity of denture base resin is affected by the build orientation rather than by the group of different microbes. Three-dimensionally printed denture base resin fabricated at a 0-degree build orientation exhibited low affinity for microbial adhesion. Three-dimensionally printed dentures may reduce microbial adhesion when printed at a 0-degree build orientation.

A novel glass ionomer cement with silver zeolite for restorative dentistry

OBJECTIVE

To develop an antimicrobial silver zeolite glass ionomer cement (SZ-GIC) and determine its biocompatibility, physical, adhesive and antibacterial properties.

METHODS

Silver nitrate and sodium zeolite were used to synthesize silver zeolite (SZ). SZ-GICs were prepared by incorporating SZ into GIC at 5% (SZ-GIC5), 2% (SZ-GIC2), or 1% (SZ-GIC1) by weight, respectively. The SZ-GICs were characterized by evaluating surface morphology, topography and elemental composition. SZ-GICs' biocompatibility was assessed by evaluating cell cytotoxicity. Their physical properties were determined by testing setting time, compressive strength, flexural strength, water sorption and solubility. Their adhesive property was assessed by evaluating micro-tensile bond strength. Their antibacterial properties were assessed by evaluating biofilm growth kinetic, metabolic activity, viability and morphology. GIC was used as a control.

RESULTS

SZ was a three-dimensional crystalline mineral. SZ-GICs (including SZ-GIC 5, 2 and 1) showed similar surface morphology and topography to GIC. SZ-GIC1 and GIC had no difference in cell cytotoxicity (p>0.05). SZ-GICs and GIC showed no difference in setting time (p>0.05). SZ-GICs had higher compressive and flexural strength than GIC (p<0.05). SZ-GIC2 and SZ-GIC1 showed lower water sorption and solubility than GIC (p<0.05). SZ-GICs had higher micro-tensile bond strength than GIC (p<0.05). Biofilms on SZ-GICs' surfaces showed lower colony-forming units, decreased metabolic activities, higher percentages of dead cells and more ruptured bacterial cells compared with those on GIC.

CONCLUSION

SZ-GIC with silver zeolite at 1% by weight are as biocompatible as conventional GIC. The SZ-GICs have enhanced physical, adhesive and antibacterial properties than GIC.

CLINICAL SIGNIFICANCE

A silver zeolite glass ionomer cement was developed. The SZ-GICs have great potential for caries prevention and management.

Inhibitory Activity of Essential Oils of Mentha spicata and Eucalyptus globulus on Biofilms of Streptococcus mutans in an In Vitro Model

The aim of this study was to evaluate the inhibitory activity of the commercially available essential oils of Mentha spicata (spearmint) and Eucalyptus globulus (eucalyptus) on Streptococcus mutans ATCC 25175 biofilms in vitro, emulating dental plaque conditions. The composition of the essential oils (EOs) was determined using gas chromatography coupled with mass spectrometry (GC-MS), with the main metabolites being Carvone (57.93%) and Limonene (12.91%) for Mentha spicata and 1,8-Cineole (Eucalyptol) (65.83%) for Eucalyptus globulus. The inhibitory activity was evaluated using the methods of agar-well diffusion and colorimetric microdilution. The inhibition halos were 18.3 ± 0.47 mm and 27.0 ± 0.82 mm, and the MICs were 1.8484 mg/mL and 1.9168 mg/mL for the EOs of Mentha spicata and Eucalyptus globulus, respectively. The activity against the biofilms was evaluated on a substrate of bovine enamel pieces using a basal mucin medium (BMM) in anaerobic conditions with daily sucrose exposition cycles in order to emulate oral cavity conditions. The EOs were applied in a concentration of 0.5% in a sterile saline vehicle with 1% polysorbate 20. After 72 h of cultivation, a significant reduction was observed (p < 0.001%) on the biofilm biomass, which was evaluated by its turbidity in suspension and using a count of the recoverable organisms with regards to the control. The effects of the Eos were not significantly distinct from each other. The EOs showed antimicrobial activity against both the Streptococcus mutans planktonic and biofilm cultures. Thus, EOs may have great potential for the development of pharmaceutical and sanitary products for oral health.

Evaluation of biofilm formation on acrylic resins used to fabricate dental temporary restorations with the use of 3D printing technology

Background

Temporary implant-retained restorations are required to support function and esthetics of the masticatory system until the final restoration is completed and delivered. Acrylic resins are commonly used in prosthetic dentistry and lately they have been used in three-dimensional (3D) printing technology. Since this technology it is fairly new, the number of studies on their susceptibility to microbial adhesion is low. Restorations placed even for a short period of time may become the reservoir for microorganisms that may affect the peri-implant tissues and trigger inflammation endangering further procedures. The aim of the study was to test the biofilm formation on acrylamide resins used to fabricate temporary restorations in 3D printing technology and to assess if the post-processing impacts microbial adhesion.

Methods

Disk-shaped samples were manufactured using the 3D printing technique from three commercially available UV-curable resins consisting of acrylate and methacrylate oligomers with various time and inhibitors of polymerization (NextDent MFH bleach, NextDent 3D Plus, MazicD Temp). The tested samples were raw, polished and glazed. The ability to create biofilm by oral streptococci (S. mutans, S. sanguinis, S. oralis, S. mitis) was tested, as well as species with higher pathogenic potential: Staphylococcus aureus, Staphylococcus epidermidis and Candida albicans. The roughness of the materials was measured by an atomic force microscope. Biofilm formation was assessed after 72 h of incubation by crystal violet staining with absorbance measurement, quantification of viable microorganisms, and imaging with a scanning electron microscope (SEM).

Results

Each tested species formed the biofilm on the samples of all three resins. Post-production processing resulted in reduced roughness parameters and biofilm abundance. Polishing and glazing reduced roughness parameters significantly in the NextDent resin group, while glazing alone caused significant surface smoothing in Mazic Temp. A thin layer of microbial biofilm covered glazed resin surfaces with a small number of microorganisms for all tested strains except S. oralis and S. epidermidis, while raw and polished surfaces were covered with a dense biofilm, rich in microorganisms.

Conclusions

UV-curing acrylic resins used for fabricating temporary restorations in the 3D technology are the interim solution, but are susceptible to adhesion and biofilm formation by oral streptococci, staphylococci and Candida. Post-processing and particularly glazing process significantly reduce bacterial biofilm formation and the risk of failure of final restoration.

Supplementary Information

The online version contains supplementary material available at 10.1186/s12903-022-02488-5.

Adhesive Ability of Different Oral Pathogens to Various Dental Materials: An In Vitro Study

Introduction. In dental treatments, the reason for secondary caries and the failure of root canal treatment is the microbial infection, which concerns most dentists. The challenge of how to reduce the number of bacteria at the filling materials and the number of residual bacteria in the root canal has become a research hotspot. In this study, the bacterial adhesion properties of several common dental materials were compared to provide a theoretical basis for the selection of antibacterial properties of dental materials. Methodology. Three commonly used dental restorative materials and five sealers in root canal treatment were selected. Each material block was immersed in the corresponding supragingival (Streptococcus mutans and Actinomyces viscosus) or subgingival (Porphyromonas gingivalis and Enterococcus faecalis) bacterial solution and cultured under anaerobic conditions at 37°C for 2, 4, 6, 8, 12, 16, 20, and 24 h. The adhesion of bacteria was observed, and the number of different bacteria adhering to various material model disks was calculated at different time intervals under a scanning electron microscope. The adherent CFU load of the materials was determined by colony counting. Results. Streptococcus mutans and Actinomyces viscosus exhibited the strongest adhesion ability to the resin material blocks. Porphyromonas gingivalis and Enterococcus faecalis exhibited the highest adhesion ability to the AH-Plus sealer block. Conclusions. In dental treatments, dental materials should be selected based on the chemical, physical, and biological properties of materials. In addition, it is necessary to develop new antibacterial dental materials.

Dual-functional adhesive containing amorphous calcium phosphate nanoparticles and dimethylaminohexadecyl methacrylate promoted enamel remineralization in a biofilm-challenged environment

OBJECTIVE

The cariogenic biofilm on enamel, restoration, and bonding interface is closely related to dental caries and composite restoration failure. Enamel remineralization at adhesive interface is conducive to protecting bonding interface and inhibiting secondary caries. This study intended to assess the remineralization efficiency of adhesive with dimethylaminohexadecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP) on initial caries lesion of biofilm-coated enamel.

METHODS

Artificial initial carious lesion was created via 72-hour immersion in demineralization solution and cariogenic biofilm was formed after 24-hour culture of Streptococcus mutans (S. mutans). Specimens were then divided into 4 groups: enamel control, enamel treated with NACP, DMAHDM and NACP+DMAHDM respectively. Samples next underwent 7-day cycling, 4 h in BHIS (brain heart infusion broth containing 1 % sucrose) and 20 h in AS (artificial saliva) per day. The pH of BHIS was tested daily. So did the concentration of calcium and phosphate in BHIS and AS. Live/dead staining, colony-forming unit (CFU) count, and lactic acid production of biofilms were measured 7 days later. The enamel remineralization efficiency was evaluated by microhardness testing and transverse microradiography (TMR) quantitatively.

RESULTS

Enamel of NACP+DMAHDM group demonstrated excellent remineralization effectiveness. And the NACP+DMAHDM adhesive released a great number of Ca²⁺ and PO₄^3- ions, increased pH to 5.81 via acid neutralization, decreased production of lactic acid, and reduced CFU count of S. mutans (P < 0.05).

SIGNIFICANCE

The NACP+DMAHDM adhesive would be applicable to preventing secondary caries, strengthening enamel-adhesive interface, and extending the lifespan of composite restoration.

Effect of Exo/Endogenous Prophylaxis Dentifrice/Drug and Cariogenic Conditions of Patient on Molecular Property of Dental Biofilm: Synchrotron FTIR Spectroscopic Study

(1) Objectives: This study is the first one to investigate the molecular composition of the dental biofilm during the exogenous and endogenous prophylaxis stages (use of dentifrice/drug) of individuals with different cariogenic conditions using molecular spectroscopy methods. (2) Materials and Methods: The study involved 100 participants (50 males and 50 females), aged 18–25 years with different caries conditions. Biofilm samples were collected from the teeth surface of all participants. The molecular composition of biofilms was investigated using synchrotron infrared microspectroscopy. Changes in the molecular composition were studied through calculation and analysis of ratios between organic and mineral components of biofilm samples. (3) Results: Based on the data obtained by synchrotron FTIR, calculations of organic and mineral component ratios, and statistical analysis of the data, we were able to assess changes occurring in the molecular composition of the dental biofilm. Variations in the phosphate/protein/lipid, phosphate/mineral, and phospholipid/lipid ratios and the presence of statistically significant intra- and inter-group differences in these ratios indicate that the mechanisms of ion adsorption, compounds and complexes arriving from oral fluid into dental biofilm during exo/endogenous prophylaxis, differ for patients in norm and caries development. (4) Conclusions: The conformational environment and charge interaction in the microbiota and the electrostatic state of the biofilm protein network in patients with different cariogenic conditions play an important role. (5) Clinical Significance: Understanding the changes that occur in the molecular composition of the dental biofilm in different oral homeostasis conditions will enable successful transition to a personalised approach in dentistry and high-tech healthcare.

Oral Microbiota Populations of Adult Dogs Consuming Wet or Dry Foods

Oral microbiota play a prominent role in canine periodontal disease and wet foods are often blamed for poor oral health, but canine oral microbial communities have been poorly studied. We aimed to determine differences in oral health measures, breath odor, and oral microbiota populations of dogs fed wet or dry food. Twelve adult dogs fed either a commercial dry (extruded) or commercial wet (canned) food for 6 wk were studied. Breath samples were measured for sulfur compounds, teeth were scored for plaque, calculus, and gingivitis by a blinded veterinary dentist, salivary pH was measured, and supragingival (SUP) and subgingival (SUB) plaque samples were collected for microbiota analysis. Plaque DNA was extracted and Illumina sequencing conducted. Phylogenetic data were analyzed using the CosmosID bioinformatics platform and SAS 9.4, with P<0.05 being significant and P<0.10 being trends. Plaque coverage tended to be higher (P<0.10) in dogs fed wet vs. dry food, but other oral health scores were not different. Dogs fed dry food had higher (P<0.05) salivary pH and lower (P<0.05) breath sulfur concentrations than those consuming wet food. Bacterial alpha diversity was higher in SUP than SUB samples, and a clear separation in beta diversity was observed between sample sites on principal coordinates analysis (PCoA) plots. In SUP samples, dogs fed wet food had a higher alpha diversity than dogs fed dry food, with PCoA plots showing a separation between wet and dry food. Relative abundances of Firmicutes, Synergistetes, and 10 bacterial genera were different (P<0.05) in SUB samples of dogs fed wet vs. dry food. Relative abundances of Fusobacteria and over 20 bacterial genera were different (P<0.05) in SUP samples of dogs fed wet vs. dry food. In general, oral health-associated bacterial taxa (Pasteurella, Capnocytophaga, Corynebacterium) were higher, while bacteria associated with poor oral health (Fretibacterium fastidiosum, Filifactor alocis, Treponema medium, Tannerella forsythia, Porphyromonas canoris, Porphyromonas gingivalis) were lower in dogs fed dry food. Such shifts in the oral microbiota may impact periodontal disease risk, but longer dietary intervention studies are required to confirm their role in the disease process. Our results suggest that dogs fed dry extruded foods have lower breath odor and tooth plaque buildup and an oral microbiota population more closely associated with oral health than dogs fed wet canned foods.

Armed to the Teeth-The Oral Mucosa Immunity System and Microbiota

The oral cavity is inhabited by a wide spectrum of microbial species, and their colonization is mostly based on commensalism. These microbes are part of the normal oral flora, but there are also opportunistic species that can cause oral and systemic diseases. Although there is a strong exposure to various microorganisms, the oral mucosa reduces the colonization of microorganisms with high rotation and secretion of various types of cytokines and antimicrobial proteins such as defensins. In some circumstances, the imbalance between normal oral flora and pathogenic flora may lead to a change in the ratio of commensalism to parasitism. Healthy oral mucosa has many important functions. Thanks to its integrity, it is impermeable to most microorganisms and constitutes a mechanical barrier against their penetration into tissues. Our study aims to present the role and composition of the oral cavity microbiota as well as defense mechanisms within the oral mucosa which allow for maintaining a balance between such numerous species of microorganisms. We highlight the specific aspects of the oral mucosa protecting barrier and discuss up-to-date information on the immune cell system that ensures microbiota balance. This study presents the latest data on specific tissue stimuli in the regulation of the immune system with particular emphasis on the resistance of the gingival barrier. Despite advances in understanding the mechanisms regulating the balance on the microorganism/host axis, more research is still needed on how the combination of these diverse signals is involved in the regulation of immunity at the oral mucosa barrier.

Surface Characteristics and Microbiological Analysis of a Vat-Photopolymerization Additive-Manufacturing Dental Resin

The wide application of additive manufacturing in dentistry implies the further investigation into oral micro-organism adhesion and biofilm formation on vat-photopolymerization (VP) dental resins. The surface characteristics and microbiological analysis of a VP dental resin, printed at resolutions of 50 μm (EG-50) and 100 μm (EG-100), were evaluated against an auto-polymerizing acrylic resin (CG). Samples were evaluated using a scanning electron microscope, a scanning white-light interferometer, and analyzed for Candida albicans (CA) and Streptococcus mutans (SM) biofilm, as well as antifungal and antimicrobial activity. EG-50 and EG-100 exhibited more irregular surfaces and statistically higher mean (Ra) and root-mean-square (rms) roughness (EG-50-Ra: 2.96 ± 0.32 µm; rms: 4.05 ± 0.43 µm/EG-100-Ra: 3.76 ± 0.58 µm; rms: 4.79 ± 0.74 µm) compared to the CG (Ra: 0.52 ± 0.36 µm; rms: 0.84 ± 0.54 µm) (p < 0.05). The biomass and extracellular matrix production by CA and SM and the metabolic activity of SM were significantly decreased in EG-50 and EG-100 compared to CG (p < 0.05). CA and SM growth was inhibited by the pure unpolymerized VP resin (48 h). EG-50 and EG-100 recorded a greater irregularity, higher surface roughness, and decreased CA and SM biofilm formation over the CG.

Immobilization of microorganisms in activated zeolite beads and alkaline pretreated straws for ammonium-nitrogen removal from urban river water

The non-treated wastewater from residential areas contains high concentrations of ammonium-nitrogen (NH₄⁺-N). When discharged into the drainage water system, it deteriorates the water quality in urban rivers. This study used two types of materials to form eco-bags, using activated zeolite bead (AZB) and alkaline pretreated straw (APS), in geotextile bags for easy recovery and reuse. The AZB and APS provided the breeding habitat for the microorganisms that promoted biofilm formation on their surface. The immobilization of engineered denitrification microorganisms facilitated the removal of NH₄⁺-N from the urban river water. The NH₄⁺-N removal in the AZB and APS bags were in the range of 64-73%, and 56-61%, respectively, while the chemical oxygen demand (COD) removal in the AZB and APS bags ranged from 33-36%, and 30-31%, respectively. In addition, as evident from DNA and microbial community analysis, the microorganisms demonstrated a greater proclivity to grow and proliferate on the surface of AZB and APS and improved the water quality of urban rivers.

Surface Modification to Modulate Microbial Biofilms-Applications in Dental Medicine

Recent progress in materials science and nanotechnology has led to the development of advanced materials with multifunctional properties. Dental medicine has benefited from the design of such materials and coatings in providing patients with tailored implants and improved materials for restorative and functional use. Such materials and coatings allow for better acceptance by the host body, promote successful implantation and determine a reduced inflammatory response after contact with the materials. Since numerous dental pathologies are influenced by the presence and activity of some pathogenic microorganisms, novel materials are needed to overcome this challenge as well. This paper aimed to reveal and discuss the most recent and innovative progress made in the field of materials surface modification in terms of microbial attachment inhibition and biofilm formation, with a direct impact on dental medicine.

Microbicidal effect of 405-nm blue LED light on Candida albicans and Streptococcus mutans dual-species biofilms on denture base resin

This study investigated: (1) the microbicidal effect of 405-nm blue LED light irradiation on biofilm formed by Candida albicans hyphae and Streptococcus mutans under dual-species condition on denture base resin, (2) the generation of intracellular reactive oxygen species (ROS) induced by irradiation, and (3) the existence of intracellular porphyrins, which act as a photosensitizer. Denture base resin specimens were prepared and C. albicans and S. mutans dual-species biofilms were allowed to form on the specimens. The biofilms were irradiated with 405-nm blue LED light and analyzed using the colony-forming unit assay, fluorescence microscopy, and scanning electron microscopy (SEM). Single-species biofilms of C. albicans and S. mutans formed on the specimens were irradiated with 405-nm blue LED light. After the irradiation, the intracellular ROS levels in C. albicans and S. mutans cells were measured. In addition, the level of intracellular porphyrins in C. albicans and S. mutans were measured. Irradiation for more than 30 min significantly inhibited the colony formation ability of C. albicans and S. mutans. Fluorescence microscopy revealed that almost all C. albicans and S. mutans cells were killed by irradiation. SEM images showed various cell damage patterns. Irradiation led to the generation of intracellular ROS and porphyrins were present in both C. albicans and S. mutans cells. In conclusion, irradiation with 405-nm blue light-emitting diode light for 40 min effectively disinfect C. albicans hyphae and S. mutans dual-species biofilms and possibly react with intracellular porphyrins resulting in generation of ROS in each microorganism.