Finite element analysis of osteosynthesis screw fixation in the bone stock: an appropriate method for automatic screw modelling

Identification of screw spacing on pediatric hip locking plate in proximal femoral osteotomy

This study describes a computational analysis technique for evaluating the effect of screw spacing and angle on the pediatric hip locking plate system in proximal femoral osteotomy in pediatric patients having DDH with an aberrant femoral head and femoral angle. Under static compressive load conditions, the stresses of the screw and bone were examined as the screw spacing and angle changed. The spacing and angle of various screws were specifically considered as variables in this study based on the pile mechanism studied in civil engineering. As with the group pile mechanism, the tighter the screw spacing under static compressive loads, the more the overlapping effect between the bone stresses and the screws develops, increasing the risk of injuring the patient's bone. Therefore, a series of simulations was performed to determine the optimal screw spacing and angles to minimize the overlapping effect of bone stress. In addition, a formula for determining the minimum screw spacing was proposed based on the computational simulation results. Finally, if the outcomes of this study are applied to pediatric patients with DDH in the pre-proximal femoral osteotomy stage, post-operative load-induced femur damage will be reduced.

Stress distributions of the short stem and the tapered wedge stem at different alignments: a finite element analysis study

BACKGROUND

The mechanical effects of stem length reduction and stem alignment on the surrounding femur remain unknown. This study directly compared the stress distribution on the surrounding femur of existing tapered wedge stems and short stems and examined the properties of stress distribution at different stem alignments in three dimensions.

METHODS

Finite element analysis was conducted for standing and walking. The cementless stem was appropriately sized to ensure adequate contact with the medial cortical bone line that contours the medullary cavity. The stem neck axis was aligned with the femoral neck axis in the mid-position and placed in 2° of the varus and valgus, 3° of flexion and extension, and 10° and 40° of anteversion.

RESULTS

Regardless of stem length, the trend of stress distribution was similar. The short stem generated less stress around the stem than the tapered wedge stem. In the coronal plane, the effect of varus and valgus deflection was small. In the sagittal plane, the stress generated around the stem was higher in the extended position than in the flexed position. In the horizontal plane, the stress generated around the stem was higher when the stem anteversion was smaller.

CONCLUSIONS

Depending on the design, short stems can reduce the stress on the surrounding bone, compared to a longer tapered wedge with similar stress distribution. Additionally, a short stem can reduce the effect of the varus position. Stems should be placed to achieve stable initial fixation while noting that stresses increase with extension and reduced anteversion.

Risk modeling of femoral neck fracture based on geometric parameters of the proximal epiphysis

BACKGROUND

Fractures of the proximal femur epiphysis are problematic for state health care because they are associated with severe medical and social problems and high morbidity and mortality rates.

AIM

To model the potential risk of hip fracture via femur geometric parameters.

METHODS

Seventy educational cadaveric femurs from people aged 14 to 80 years, 10 X-ray images from the records of the Human Anatomy Department and 10 X-ray images from the Department of Traumatology, Orthopedics and Disaster Surgery of Sechenov University, were evaluated. The parameters of the fractured bone were measured using images captured with a Canon d60 camera. The projection values of the proximal epiphysis of the cadaveric femurs and geometric parameters of the bones shown in the X-ray images were measured with Autodesk software (AutoCAD 2018). Analysis of the video frames showing bone rotation reveal that the greater trochanter can be inscribed in a parallelepiped, where one of the faces is parallel to the plane of view in the frontal standard projection and is rectangular. The angle of bone rotation obtained by turning the cube corresponded to the angle measured with the second technique. This reliable method of calculating the rotation of the bone relative to the anterior projection was employed in subsequent calculations. The geometric parameters of the femur were measured using X-ray images according to the proposed method.

RESULTS

The geometric parameters of 70 femurs were analyzed, and correlation coefficients were calculated. Our measurement results were compared with those reported by other authors. The potential influence of femur geometry on force distribution in the proximal epiphysis of the femur was described, and a 2-dimensional model of the femur epiphysis associated with minimal neck fracture risk was provided. The assessment of the geometric parameters of the femoral epiphysis indicated the greatest risk of a varus fracture of the neck if the angle of the minimal resistance zone (AMRZ) index > 24° and the neck-shaft angle (NSA) < 127.5°. In contrast, the minimum risk was observed at AMRZ < 14° and NSA > 128.87°.

CONCLUSION

The proposed method provides the potential femur neck fracture risk based on geometric parameters.

A NEW ANATOMICAL PLATE FOR EXTRA-ARTICULAR DISTAL HUMERAL FRACTURES: BIOMECHANICAL STUDY

Introduction

We compared the mechanical properties of two fixation techniques for the treatment of extra-articular distal third humeral fractures.

Materials and Methods

Two groups were created from twenty-four humeri. Group 1 was instrumented using a new, precontoured, 8-hole (3.5-mm-diameter) locking compression plate (LCP) placed anterolaterally. Group 2 was instrumented using an 8-hole (3.5-mm-diameter) precontoured posterolateral LCP plate placed on the distal humerus. Four-point bending tests and torsion tests were performed until the specimens broke.

Results

The four-point bending stiffness test showed that the stiffness of anterolaterally fixed humeri was significantly higher than that of posterolaterally fixed humeri (p<0.05). Torsion testing revealed that posterolateral fixation was associated with better yield strength (p<0.05), but the torsional stiffness did not differ significantly between the two plates (p> 0.05).

Conclusions

The anterolateral plate exhibited higher bending stiffness and torsional yield strength than the posterolateral plate. Anterolateral plate fixation can thus be used to manage extra-articular distal humeral fractures. Multiaxial locking screws ensure rigid fixation, allow early elbow motion without olecranon fossa impingement, and prevent iatrogenic injury of the triceps muscle. Level of Evidence I, Therapeutic Studies Investigating the Results of Treatment.

A Novel Screw Drive for Allogenic Headless Position Screws for Use in Osteosynthesis-A Finite-Element Analysis

Due to their osteoconductive properties, allogenic bone screws made of human cortical bone have advantages regarding rehabilitation compared to other materials such as stainless steel or titanium. Since conventional screw drives like hexagonal or hexalobular drives are difficult to manufacture in headless allogenic screws, an easy-to-manufacture screw drive is needed. In this paper, we present a simple drive for headless allogenic bone screws that allows the screw to be fully inserted. Since the screw drive is completely internal, no threads are removed. In order to prove the mechanical strength, we performed simulations of the new drive using the Finite-Element method (FEM), validated the simulations with a prototype screw, tested the novel screw drive experimentally and compared the simulations with conventional drives. The validation with the prototype showed that our simulations provided valid results. Furthermore, the simulations of the new screw drive showed good performance in terms of mechanical strength in allogenic screws compared to conventional screw drives. The presented screw drive is simple and easy to manufacture and is therefore suitable for headless allogenic bone screws where conventional drives are difficult to manufacture.

Performance of a Piezoelectric Energy Harvesting System for an Energy-Autonomous Instrumented Total Hip Replacement: Experimental and Numerical Evaluation

Instrumented implants can improve the clinical outcome of total hip replacements (THRs). To overcome the drawbacks of external energy supply and batteries, energy harvesting is a promising approach to power energy-autonomous implants. Therefore, we recently presented a new piezoelectric-based energy harvesting concept for THRs. In this study, the performance of the proposed energy harvesting system was numerically and experimentally investigated. First, we numerically reproduced our previous results for the physiologically based loading situation in a simplified setup. Thereafter, this configuration was experimentally realised by the implantation of a functional model of the energy harvesting concept into an artificial bone segment. Additionally, the piezoelectric element alone was investigated to analyse the predictive power of the numerical model. We measured the generated voltage for a load profile for walking and calculated the power output. The maximum power for the directly loaded piezoelectric element and the functional model were 28.6 and 10.2 µW, respectively. Numerically, 72.7 µW was calculated. The curve progressions were qualitatively in good accordance with the numerical data. The deviations were explained by sensitivity analysis and model simplifications, e.g., material data or lower acting force levels by malalignment and differences between virtual and experimental implantation. The findings verify the feasibility of the proposed energy harvesting concept and form the basis for design optimisations with increased power output.

Computational analysis of the effects of interprosthetic distance on normal and reduced cortical thickness femur models

Distal femoral fractures associated with the femoral stem in a well-fixed hip arthroplasty pose a risk of an interprosthetic fracture, the treatment of which is known as difficult. To effectively prevent and treat IP fractures, biomechanical effects must be demonstrated. We defined eight variations of the interprosthetic distance ranging from 48 mm overlap to 128 mm gap. Femoral geometries with normal and reduced cortical thickness were modeled to evaluate the effects of cortical thickness. In addition to the intact model, a total of 16 finite element models were analyzed under physiological boundary conditions. Maximum and minimum principal strains on the lateral and medial cortex surfaces were always found to be greater in models with reduced cortical thickness than in normal femurs. The model with 48 mm overlapping interprosthetic distance produced the least peak strain and the model with 16 mm interprosthetic gap produced the greatest strain with both normal and reduced cortical thickness. The screw holes produced local strain concentrations and increased the peak strains on the cortex surfaces, especially close to the stem tip. Statistically, a significant correlation (R² = 0.9483) was found between strain shielding and interprosthetic distance. Axial stiffness, interfragmentary shear motion, and maximum von-Mises stress on the distal plate showed a high correlation with the interprosthetic distance. It was concluded that the overlapping structures are superior to other fixations we analyzed in that they offer better mechanical stability and eliminates the local strain concentrations.

Finite Element Analysis of Fracture Fixation

PURPOSE OF REVIEW

Fracture fixation aims to provide stability and promote healing, but remains challenging in unstable and osteoporotic fractures with increased risk of construct failure and nonunion. The first part of this article reviews the clinical motivation behind finite element analysis of fracture fixation, its strengths and weaknesses, how models are developed and validated, and how outputs are typically interpreted. The second part reviews recent modeling studies of the femur and proximal humerus, areas with particular relevance to fragility fractures.

RECENT FINDINGS

There is some consensus in the literature around how certain modeling aspects are pragmatically formulated, including bone and implant geometries, meshing, material properties, interactions, and loads and boundary conditions. Studies most often focus on predicted implant stress, bone strain surrounding screws, or interfragmentary displacements. However, most models are not rigorously validated. With refined modeling methods, improved validation efforts, and large-scale systematic analyses, finite element analysis is poised to advance the understanding of fracture fixation failure, enable optimization of implant designs, and improve surgical guidance.

Intralesional curettage versus prosthetic replacement for bone tumors - a finite element analysis case of limb salvage simulation in biomechanics

BACKGROUND AND OBJECTIVES

To compare mechanical properties of femoral tumor treatments so that better operative strategy for limb tumors surgery is optimized.

METHODS

Fourteen femoral CT images were randomly selected to rebuild 3D models by MIMICS. They were then executed by reverse engineering softwares for simulative modes. Mode #1: Intralesional curettage with cement filled plus fixator; Mode #2: Distal femur resection with tumorous prosthesis replaced. Finally, the mechanical aspects such as stress and displacement were compared by finite element analysis.

RESULTS

Analyzed by AnSys, the observation indexes were measured as follows: for displacement of femurs, d=1.4762 (< a=3.9042 < c=3.9845 < b=4.1159) in mm is the most staple of all models; for displacement of implants (fixators or prostheses), it's similar to the behavior of femurs and with no significant difference; for stresses of femurs, no significant difference was found among all models; the stresses of implants (fixations and prostheses) were observed as d=39.6334 (< a=58.6206 < c=61.8150 < b=62.6626) in MPa correspondently, which is the least; for stresses of the general system, the average of peak values for integrated devices of all models are: d=40.8072 (< a=58.6206 < c=61.7831< b=62.6626) in MPa, which is also the least. As a final result, both maximum values for displacement and stress of mode 2 are lower than those of mode 1.

CONCLUSIONS

Our finite element analysis of limb salvage simulation in biomechanics proved that, to treat distal femoral bone tumors, prosthetic replacement is more efficient than intralesional curettage.

Interfragmentary lag screw and locking plate combination in simple distal femoral fractures: A finite element analysis

OBJECTIVE

The aim of this study was to evaluate the strength of the locking plate and lag screw construct that is applied in two different working lengths on the simple distal femur fracture model with a finite element analysis (FEA) method.

METHODS

From the computerized tomography scan data of a 60-year-old healthy male, the AO/OTA 33A1-type fracture model was simulated; the fracture gap was stabilized with the models of locking plate construct with (groups C and D) or without an interfragmentary lag screw (groups A and B). Furthermore, 102-mm plate (groups A and C) and 82-mm plate working lengths (groups B and D) were tested using FEA. Two loading conditions (axial compression and torsion) were applied at the center of the femoral head. Construct stiffness, interfragmentary micromotion, and the peak von Mises stress (VMS) on the plate were assessed.

RESULTS

Group D provided the highest axial stiffness (1347 N/mm), and group A was the weakest (439 N/mm). With the lag screw, shear micromotion remained generally low compared with that without the screw for all axial and torsional load levels and for both plate working lengths, i.e., 0.23 mm with lag screw versus 0.43 mm without lag screw (102 mm working length, 700 N). The percentage decreases of shear micromotion under axial (350/700/1400 N) and torsional loads for the 102-mm working length were >22% and 73%, respectively; while those for the 82-mm working length were >28% and 33%, respectively. The reduction of axial micromotion was observed with the lag screw for all axial load levels as well as for both plate working lengths, i.e., 0.33 mm with lag screw versus 0.87 mm without lag screw (102-mm working length, 700 N). The percentage decreases of axial micromotion under axial loading (350/700/1400 N) for 102 mm and 82 mm working lengths were >42% and 50%, respectively. The peak VMS on the plate stayed generally low with lag screw compared with without lag screw throughout all tested load levels, as well as for both plate working lengths, i.e., 124.26 MPa versus 244.39 MPa (102 mm working length, 700 N). The percentage decreases of the peak VMS under axial (350/700/1400 N) and torsional loads for the 102-mm working length were >40% and 69%, respectively, while those for the 82-mm working length were >47% and 61%, respectively.

CONCLUSION

The current FEA concludes that in a simple distal femur fracture, adding a lag screw to a locking plate construct provides better torsional stability with a 102-mm plate working length and better axial stability with a 82-mm plate working length. Additionally, the strength of the materials is increased and implant failure can be minimized by using this technique.

Comparison of Fragment Removal Versus Internal Fixation for Treatment of Pipkin I Femoral Head Fractures: A Finite Element Analysis

Fragment removal and internal fixation are the principle treatments for Pipkin type I femoral head fractures. The aim of this study was to compare, using a finite-element method, changes in stress on the femoral head after 2 different operation types. A three-dimensional (3D) finite-element model of a Pipkin type I femoral head fracture was generated with MIMICS and ABAQUS software. A 3D numerical screw model was reconstructed based on data from BIOFIX and using SOLIDWORKS software. The screw was implanted in the fragment and femoral head to reconstruct the implantation. Stress changes on the femoral head after removal of the fragment and internal fixation were investigated. Mean stresses along 13 points were 16.94 ± 16.79 MPa in the fragment removal group and 14.17 ± 14.08 MPa in the internal fixation group (P &lt; 0.05). Random tests indicated that the mean stresses along 50 randomly determined points were 25.41 ± 12.12 MPa in the fragment removal group and 19.45 ± 14.62 MPa in the internal fixation group (P &lt; 0.05). Compared with internal fixation, fragment removal led to greater stress that was more concentrated in the femoral head.

Biomechanical analysis for five fixation techniques of Pauwels-III fracture by finite element modeling

BACKGROUND AND OBJECTIVES

There are many fixation methods for Pauwels- III fracture, the most common implants are Locking Plate (LP), Dynamic Hip Screw (DHS), Multiple Lag Screw (MLS), and mixed fixture (DHS+MLS) implants, the common procedure is HemiArthroplasty (HA). However, how these fixtures biomechanically function is not clear. The aims of this study are to compare the mechanical behaviors of these five implants by finite element modeling and determinate the most suitable procedure for individuals with Pauwels- III fractures.

METHODS

We gathered 20 sets of femur images from CT scans in the *.dicom format first, and then processed them by using reverse engineering software programs, such as Mimics, Geomagic Studio, UG-8, Pro-Engineer and HyperMesh. Finally, we assembled and analyzed the five types of fixture models, the LP, DHS, MLS, DHS+LS and HA models, by AnSys.

RESULTS

These numerical models of Pauwels III fractures, including fixators and a simulative HA, were validated by a previous study and a cadaver test. Our analytical findings include the following: the displacements of all fixtures were between 0.3801 and 1.0834 mm, and the differences were not statistically significantly different; the resulting average peaks in stress were e(Ha) = 43.859 ≤ d(LP) = 60.435 ≤ b(MLS) = 68.678 < c(LS+DHS) = 98.478 < a(DHS) = 248.595 in Mpa, indicating that the stress of DHS and DHS+LS are greater than those of LP, HA and MLS, while the last 3 models were not significantly different.

CONCLUSIONS

To optimize the treatment for Pauwels III factures clinically, HA and LP should be proposed.

Finite Element Analysis of Custom Shoulder Implants Provides Accurate Prediction of Initial Stability

Custom reverse shoulder implants represent a valuable solution for patients with large bone defects. Since each implant has unique patient-specific features, finite element (FE) analysis has the potential to guide the design process by virtually comparing the stability of multiple configurations without the need of a mechanical test. The aim of this study was to develop an automated virtual bench test to evaluate the initial stability of custom shoulder implants during the design phase, by simulating a fixation experiment as defined by ASTM F2028-14. Three-dimensional (3D) FE models were generated to simulate the stability test and the predictions were compared to experimental measurements. Good agreement was found between the baseplate displacement measured experimentally and determined from the FE analysis (Spearman’s rank test, p < 0.05, correlation coefficient ρs = 0.81). Interface micromotion analysis predicted good initial fixation (micromotion <150 µm, commonly used as bone ingrowth threshold). In conclusion, the finite element model presented in this study was able to replicate the mechanical condition of a standard test for a custom shoulder implants.

Biomechanical study of different internal fixations in Pauwels type III femoral neck fracture - A finite elements analysis

OBJECTIVE

To evaluate biomechanical behavior of different internal fixation methods for the treatment of Pauwels Type III femoral neck fractures.

METHODS

Three internal fixators were developed to treat Pauwels Type III femoral neck fracture using finite elements: dynamic hip screw (DHS); DHS combined with anti-rotation screw; three cannulated screws in an inverted triangular configuration (ASNIS). Under the same conditions, vertical fracture displacement, and maximum and minimum principal, and Von Mises stresses were evaluated.

RESULTS

The vertical displacements evaluated were: 5.43 mm, 5.33 mm and 6.22 mm, rotational displacements values were 1.1 mm, 0.4 mm and 1.3 mm; maximum principle stress values obtained for the upper region of the femoral neck were 3.26 hPa, 2.77 hPa, and 4.5 hPa, minimum principal stress values obtained for the inferior region of the femoral neck were -1.97 hPa, -1.8 hPa and t -3.15 hPa; Von Mises peak stress values were 340.0 MPa, 315.5 MPa and 326.1 Mpa, for DHS, DHS with anti-rotation device, and ASNIS, respectively. Conclusion: The DHS combined with anti-rotation screw yielded better results in terms of rotational and vertical displacements, traction and compression distributions on fractures, and Von Mises stress, demonstrating mechanical superiority for Pauwels Type III fracture.

Modeling age-related changes in the mechanical behavior of the fracture-fixated human tibia bone during healing

The evolutionary healing phenomenon of fractured tibia bone was investigated by comparing the bio-mechanical response of the human tibia following fracture fixation for two ranges of patient ages, when a body weight pressure (BWP) is applied. Three-dimensional finite element models have been developed by adopting the biomechanical characteristics of cortical and trabecular tibia bones, and considering the time-varying callus properties during the healing process for the two patients. The stress and strain levels generated within the fractured tibia bone by the screw tight fit during the assembly process revealed its dependence on the bone stiffness that degrades with age. They have an impact on primary stability of the implants prior to the osseointegration. The gap capacity to resist and allow a gradual BWP load transfer, through the callus for the tibia bone models, was analyzed. In fact, from 10 weeks after surgery, the callus allowed the BWP transfer for young patients, which guarantees sufficient structure stabilization of the fractured tibia. However, an insufficient load was transferred to the fracture gap for the old patient, even beyond 16 weeks, which delayed the bone consolidation.

A programmable, fast-fixing, osteo-regenerative, biomechanically robust bone screw

The use of a screw for repairing defected bones is limited by the dilemma between stiffness, bioactivity and internal fixation ability in current products. For polymer bone screw, it is difficult to achieve the bone stiffness and osteo-induction. Polymer composites may enhance bioactivity and mechanical properties but sacrifice the shape memory properties enormously. Herein, we fabricated a programmable bone screw which is composed of shape memory polyurethane, hydroxyapatite and arginylglycylaspartic acid to resolve the above problem. This composite has significantly improved mechanical and shape-memory properties with a modulus of 250 MPa, a shape fixity ratio of ~90% and a shape recovery ratio of ~96%. Moreover, shape fixity and recovery ratios of the produced SMPC screw in the simulative biological condition were respectively ~80% and ~82%. The produced screw could quickly recover to its original shape in vitro within 20 s leading to easy internal fixation. Additionally, the composite could support mesenchymal stem cell survival, proliferation and osteogenic differentiation in vitro tests. It also promoted tissue growth and showed beneficial mechanical compatibility after implantation into a rabbit femoral intracondyle for 12 weeks with little inflammation. Such bone screw exhibited a fast-fixing, tightened fitting, enhanced supporting and boosted bioactivity simultaneously in the defective bone, which provides a solution to the long-standing problem for bone repairing. We envision that our composite material will provide valuable insights into the development of a new generation of bone screws with good fixation and osteogenic properties. STATEMENT OF SIGNIFICANCE: The main obstacles to a wider use of a bone screw are unsatisfied stiffness, inflammatory response and screw loosening issues. Herein, we report a programmable screw with mechanically robust, bioactive and fast-fixing performances. The shape memory polymer composite takes advantage of the component in the natural bone and possesses a stable bush-like structure inside through the covalent bonding, and thus achieve significantly improved mechanical and memory properties. Based on its shape memory effect, the produced screw was proved to offer a recovery force to surroundings and promote the bone regeneration effectively. Therefore, the composite realizes our expectations on functions through structure design and paves a practical and effective way for the development of a new generation of bone screws.

Isocyanate Modified GO Shape-Memory Polyurethane Composite

Shape-memory composites have benefits for minimally invasive surgery, but their wider applications for bone repair are hindered by conflicts between the mechanical and memory performances, especially at load-bearing locations. In this study, we fabricated a graphene oxide shape-memory polyurethane composite through the chemical combination of graphene oxide and isocyanate, in order to realize satisfactory mechanical and shape-memory effects. As desired, a modulus of ~339 MPa and a shape recovery ratio of 98% were achieved, respectively, in the composite. In addition, finite element analysis demonstrated that, after being implanted in a defective bone through a minimally invasive treatment, where the highest stress was distributed at the implant-bone interface, this composite could offer a generated force during the recovery process. Furthermore, we also discuss the origins of the improved mechanical and memory properties of the composites, which arise from increased net-points and the stable molecular structure inside. Therefore, with its superior structure and properties, we envision that this shape-memory composite can provide new insights toward the practical application of shape-memory polymers and composites in the field of bone repair.

Evaluating the evidentiary value of the analysis of skeletal trauma in forensic research: A review of research and practice

Understanding bone trauma characteristics is a fundamental component of forensic investigations that can assist in understanding the nature of blunt trauma related deaths. The variation of each blunt force trauma (BFT) injury is dependent on a magnitude of factors including, age, sex, health, angle of impact, impact mechanism, impact force and clothing, making BFT one of the more difficult area of trauma to interpret solely based on skeletal fractures. A detailed literature review was performed to assess the value and scientific rigour of the current research in forensic anthropology, forensic pathology and biomechanics that attempts to provide an objective framework in which forensic practitioners can assess and interpret BFT injuries. Four areas of research which investigate the analysis of BFT are examined. These included research involving experiments on animal models; experiments on human models (and synthetic models); computer modelling, and research/publications including 'mild', 'moderate' and 'severe' as descriptions of impact force, resulting from trauma. Also briefly discussed is how BFT research is framed within medicolegal contexts. While many published works have contributed to the understanding of the biomechanics of BFT, more research that can provide an objective means to accurately assess and interpret BFT injures is required.

Should early weightbearing be allowed after intramedullary fixation of trochanteric femur fractures? A finite element study

BACKGROUND

This study aims to investigate the effects of early weightbearing after intramedullary fixation of trochanteric fractures.

METHODS

Femurs with different types of trochanteric fractures were modeled according to AO/OTA classification. Fractures were ideally reduced with one mm gap between fragments and fixed with intramedullary nails. Forces were applied simulating single- (Body weight: 60 kg, joint reaction force: 1999.2 N, abductor muscle force:1558.8 N) and double-leg standing positions (Joint reaction force: 196 N). In another model, a 500 Nm rotational force was applied as a simulation of a fall.

RESULTS

A higher level of stress was determined at the calcar femorale, the fracture site, the holes for the lag screws, and the hole for the proximal locking screw on the nail, the threadless parts of the lag screws, and the mid-portion of the nail. During the single-leg stance, up to 3 mm displacement was observed with the reverse oblique type of fractures. In the simulation of the fall, 1.5 mm displacement occurred at the fracture site. No displacement was measured at stabile and type 31A2 fracture models. In addition, higher levels of stress were measured at the body of the nail (up to 133 MPa), proximal screws (up to 133 MPa) and at the bone distal to the nail (up to 84.3 MPa), but all values were under the limit of the yield stress of the bone and the titanium.

CONCLUSION

Full weightbearing after intramedullary fixation of trochanteric femur fractures may be allowed except in obese patients and patients with 31A3 type fractures according to the AO/OTA classification. The use of support is recommended in order to prevent complications. Implant removal can be discussed with patients after fracture union in order to prevent possible periprosthetic fractures.

COMPARATIVE ANALYSIS FOR THREE FIXTURES OF PAUWELLS-II BY THE BIOMECHANICAL FINITE ELEMENT METHOD

Little is known about why and how biomechanics govern the hypothesis that three-Lag-Screw (3LS) fixation is a preferred therapeutic technique. A series models of surgical internal-fixation for femoral neck fractures of Pauwells-II will be constructed by an innovative approach of finite element so as to determine the most stable fixation by comparison of their biomechanical performance. Seventeen sets of CT scanned femora were imported onto Mimics extracting 3D models; these specimens were transferred to Geomagic Studio for a simulative osteotomy and kyrtograph; then, they underwent UG to fit simulative solid models; three sorts of internal fixators were expressed virtually by Pro-Engineer. Processed by Hypermesh, all compartments were assembled onto three systems actually as “Dynamic hip screw (DHS), 3LS and DHS+LS”. Eventually, numerical models of Finite Elemental Analysis (FEA) were exported to AnSys for solution. Three models for fixtures of Pauwells-II were established, validated and analyzed with the following findings: Femoral-shaft stress for [Formula: see text](3LS) is the least; Internal-fixator stress (MPa) for [Formula: see text]; Integral stress (MPa) for [Formula: see text]; displacement of femoral head (mm) for a[Formula: see text](DHS+LS) = 0.735; displacement of femoral shaft (mm) for [Formula: see text]; and displacement of fixators for [Formula: see text]. Mechanical comparisons for other femoral parks are insignificantly different, and these data can be abstracted as follows: the stress of 3LS-system was checked to be the least, and an interfragmentary displacement of DHS+LS assemblages was assessed to be the least”. A 3LS-system should be recommended to clinically optimize a Pauwells-II facture; if treated by this therapeutic fixation, breakage of fixators or secondary fracture is supposed to occur rarely. The strength of this study is that it was performed by a computer-aided simulation, allowing for design of a preoperative strategy that could provide acute correction and decrease procedure time, without harming to humans or animals.

Biomechanics of sacropelvic fixation: a comprehensive finite element comparison of three techniques

PURPOSE

Sacropelvic fixation is frequently used in combination with thoracolumbar instrumentation for complex deformity correction and is commonly associated with pseudoarthrosis, implant failure and loosening. This study compared pedicle screw fixation (PED) with three different sacropelvic fixation techniques, namely iliac screws (IL), S2 alar-iliac screws (S2AI) and laterally placed triangular titanium implants (SI), all in combination with lumbosacral instrumentation, accounting for implant micromotion.

METHODS

Existing finite element models of pelvis-L5 of three patients including lumbopelvic instrumentation were utilized. Moments of 7.5 Nm in the three directions combined with a 500 N compressive load were simulated. Measured metrics included flexibility, instrumentation stresses and bone-implant interface loads.

RESULTS

Fixation effectively reduced the sacroiliac flexibility. Compared to PED, IL and S2AI induced a reduction in peak stresses in the S1 pedicle screws. Rod stresses were mostly unaffected by S2AI and SI, but IL demonstrated a stress increase. In comparison with a previous work depicting full osteointegration, SI was found to have similar instrumentation stresses as those due to PED.

CONCLUSIONS

Fixation with triangular implants did not result in stress increase on the lumbosacral instrumentation, likely due to the lack of connection with the posterior rods. IL and S2AI had a mild protective effect on S1 pedicle screws in terms of stresses and bone-implant loads. IL resulted in an increase in the rod stresses. A comparison between this study and previous work incorporating full osteointegration demonstrates how these results may be applied clinically to better understand the effects of different treatments on patient outcomes. These slides can be retrieved under Electronic Supplementary Material.

Evaluation of iliac screw, S2 alar-iliac screw and laterally placed triangular titanium implants for sacropelvic fixation in combination with posterior lumbar instrumentation: a finite element study

PURPOSE

This study aimed to implement laterally placed triangular titanium implants as a technique of sacropelvic fixation in long posterior lumbar instrumentation and to characterize the effects of iliac screws, S2 alar-iliac screws and of triangular implants on rod and S1 pedicle screw stresses.

METHODS

Four female models of the lumbopelvic spine were created. For each of them, five finite element models replicating the following configurations were generated: intact, posterior fixation with pedicle screws to S1 (PED), with PED and iliac screws (IL), with PED and S2 alar-iliac (S2AI) screws, and with PED and bilateral triangular titanium implants (SI). Simulations were conducted in compression, flexion-extension, lateral bending and axial rotation. Rod stresses in the L5-S1 segment as well as in the S1 pedicle screws were compared.

RESULTS

One anatomical model was not simulated due to dysmorphia of the sacroiliac joints. PED resulted in the highest implant stresses. Values up to 337 MPa in lateral bending were noted, which were more than double than the other configurations. When compared with IL, S2AI and SI resulted in lower stresses in both screws and rods (on average 33% and 41% for S2AI and 17% and 50% for SI).

CONCLUSIONS

Implant stresses after S2AI and SI fixations were lower than those attributable to IL. Therefore, pedicle screws and rods may have a lower risk of mechanical failure when coupled with sacropelvic fixation via S2AI or triangular titanium implants, although the risk of clinical loosening remains an area of further investigation. These slides can be retrieved under Electronic Supplementary Material.

Plating System Design Determines Mechanical Environment in Long Bone Mid-shaft Fractures: A Finite Element Analysis

Purpose: Internal fixation device failure is rare but unavoidable. Fatigue-related mechanisms are responsible for most mechanical failures of orthopedic plates. Plate design needs to be optimized for both long fatigue life and bone healing. Only in this way can we reduce the occurrence of internal fixation failure. To address this issue, we aimed to provide a theoretical basis for improving the design of orthopedic plates. Material and Methods: The finite element method was used to conduct a computational investigation. Three groups of plate models were designed with varied working lengths and other elements. By fixing these plates to tibial mid-shaft fracture models, parameters of the mechanical environment around the fracture site were recorded and analyzed. Results: Plate working length, existence of holes within the working length, and plate length are important factors that influence the mechanical environment of the fracture site. The screw-bone interface is the weakest part in internal fixation failure. Fractures fixed by traditional plates that had holes in the working length have larger interfragmentary movement, and these plates have more severe stress concentration than plates without holes in the working length. Conclusions: We presented some suggestions for the plating system. First, partial weight bearing is recommended in the early postoperative period. Second, the working length of the plate does have an optimal range, depending on the fracture types. Finally, the hole within the working length should be removed to avoid stress concentration and facilitate fracture healing. Based on the findings from this study, recommendations can be developed to improve clinical practices and plating system design.

Biomechanics of two external fixator devices used in rat femoral fractures

The use of external fixators allows for the direct investigation of newly formed interfragmentary bone, and the radiographic evaluation of the fracture. We validated the results of a finite element (FE) model with the in vitro stiffness' of two widely used external fixator devices used for in vivo analysis of fracture healing in rat femoral fractures with differing construction (Ti alloy ExFix1 and PEEK ExFix2). Rat femoral fracture fixation was modeled using two external fixators. For both constructs an osteotomy of 2.75 mm was used, and offset maintained at 5 mm. Tufnol, served as standardized substitutes for rat femora. Constructs were loaded under axial compression and torsion. Overall axial and torsional stiffness were compared between the in vitro models and FE results. FE models were also used to compare the fracture movement and overall pattern of von Mises stress across the external fixators. In vitro axial stiffness of ExFix1 was 29.26 N/mm ± 3.83 compared to ExFix2 6.31 N/mm ± 0.67 (p* < 0.05). Torsional stiffness of ExFix1 was 47.5 Nmm/° ± 2.71 compared to ExFix2 at 19.1 Nmm/° ±1.18 (p* < 0.05). FE results predicted similar comparative ratios between the ExFix1 and 2 as the in vitro studies. FE results predicted considerably larger interfragmentary motion in the ExFix2 comparing to ExFix1. We demonstrated significant differences in the stiffness' of the two external fixators as one would expect from such variable designs; yet, importantly we validated the utility of an FE model for the analysis and prediction of changes in fracture mechanics dependent on fixator choice. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 37:293-298, 2019.

Anatomic grooved stem mitigates strain shielding compared to established total hip arthroplasty stem designs in finite-element models

Aseptic loosening remains a major problem for uncemented femoral components in primary total hip arthroplasty (THA). Ideally, bone adaptation after THA manifests minimally and local bone density reduction is widely avoided. Different design features may help to approximate initial, post-THA bone strain to levels pre-THA. Strain-shielding effects of different SP-CL stem design features are systematically analyzed and compared to CLS Spotorno and CORAIL using finite element models and physiological musculoskeletal loading conditions. All designs show substantial proximal strain-shielding: 50% reduced medial surface strain, 40–50% reduction at lateral surface, >120 µm/m root mean square error (RMSE) compared to intact bone in Gruen zone 1 and >60 µm/m RMSE in Gruen zones 2, 6, and 7. Geometrical changes (ribs, grooves, cross sections, stem length, anatomic curvature) have a considerable effect on strain-shielding; up to 20%. Combinations of reduced stem stiffness with larger proximal contact area (anatomically curved, grooves) lead to less strain-shielding compared to clinically established implant designs. We found that only the combination of a structurally flexible stem with anatomical curvature and grooves improves strain-shielding compared to other designs. The clinical implications in vivo of this initial strain-shielding difference are currently under evaluation in an ongoing clinical analysis.

Comparative analysis for five fixations of Pauwels-I by the biomechanical finite-element method

Background: Little is known about how biomechanics govern the five fixtures such as DHS, MLS, DHS + LS, LP, and HA are accepted as common therapeutic techniques. Aims and objectives: A series of numerical models for a femoral neck fracture of Pauwels-I will be constructed by innovative approach of finite element in order to determine the most optimized option in comparison with biomechanical performance. Method: Twenty sets of computer tomography scanned femora were imported onto Mimics to extract 3 D models; these specimens were transferred to Geomagic-Studio for a simulative osteotomy and kyrtograph; then, they underwent UG to fit simulative solid models; 5 sorts of fixture were then expressed by Pro-Engineer virtually. After processing with HyperMesh, all compartments (fracture model + internal implant) were assembled onto 5 systems: "Dynamic Hip Screw (DHS), Multiple Lag screw (MLS), DHS + LS, femoral Locking Plate (LP) and HemiArthroplasty (HA)." Eventually, numerical models of the finite-elemental analysis were exported to AnSys to determine the solution. Result: Four models of fixation and a simulation of HA for Pauwels-I were established, validated, and analyzed with the following findings: In term of displacement, these 5 fixtures ranged between 0.3801 and 0.7536 mm have no significant difference; in term of stress, the averages of peaks for integral assemblage are b(MLS) = 43.5766 ≈< d(LP) = 43.6657 ≈< e(Ha) = 43.6657 < c(DHS + LS) = 66.5494 < a(DHS) = 105.617 in MPa indicate that MLS, LP and HA are not significantly different, but less than DHS + LS or DHS in each. Conclusion: A fixture of MLS or LP with optional HA should be recommended to clinically optimize a Pauwels-I facture.

Clinical application of arthroscopy-assisted minimally invasive therapy in Chinese elderly with type III Pilon fracture

Objective

Pilon fracture is so complex that its therapy poses a great challenge to surgeons. Few studies have compared arthroscopy-assisted minimally invasive therapy and external fixation combined with limited internal fixation (EFLIF), and an optimal choice of surgical therapy remains unclear in patients with type III Pilon fracture. Moreover, to our knowledge, very few studies have specifically evaluated arthroscopy-assisted minimally invasive therapy in Chinese elderly with type III Pilon fracture. The current study was performed to observe the clinical application of arthroscopy-assisted minimally invasive therapy, compared with EFLIF, in Chinese elderly with type III Pilon fracture.

Methods

There were 230 Chinese elderly with type III Pilon fracture assigned to undergo EFLIF (group A, n=115) or arthroscopy-assisted minimally invasive therapy (group B, n=115), and followed up for 1 year after surgery.

Results

Age, sex, causes, sides and types of Pilon fractures were not different between the two groups (P>0.05 for all). Compared with EFLIF, arthroscopy-assisted minimally invasive therapy achieved a better reduction result, bone union and Mazur system (P<0.05 for all). Patient satisfaction, screw loosening and infection prevalence were not different between the two groups (P>0.05 for all). There was no skin necrosis in the two groups. Traumatic arthritis had a significantly lower prevalence in participants with arthroscopy-assisted minimally invasive therapy than EFLIF (P<0.05 for all).

Conclusion

Compared with EFLIF, arthroscopy-assisted minimally invasive therapy for type III Pilon fracture significantly improved reduction result, bone union and functional status, and decreased traumatic arthritis, demonstrating that arthroscopy-assisted minimally invasive therapy is an optimal choice for type III Pilon fracture in Chinese elderly.

A Validated Open-Source Multisolver Fourth-Generation Composite Femur Model

Synthetic biomechanical test specimens are frequently used for preclinical evaluation of implant performance, often in combination with numerical modeling, such as finite-element (FE) analysis. Commercial and freely available FE packages are widely used with three FE packages in particular gaining popularity: abaqus (Dassault Systèmes, Johnston, RI), ansys (ANSYS, Inc., Canonsburg, PA), and febio (University of Utah, Salt Lake City, UT). To the best of our knowledge, no study has yet made a comparison of these three commonly used solvers. Additionally, despite the femur being the most extensively studied bone in the body, no freely available validated model exists. The primary aim of the study was primarily to conduct a comparison of mesh convergence and strain prediction between the three solvers (abaqus, ansys, and febio) and to provide validated open-source models of a fourth-generation composite femur for use with all the three FE packages. Second, we evaluated the geometric variability around the femoral neck region of the composite femurs. Experimental testing was conducted using fourth-generation Sawbones® composite femurs instrumented with strain gauges at four locations. A generic FE model and four specimen-specific FE models were created from CT scans. The study found that the three solvers produced excellent agreement, with strain predictions being within an average of 3.0% for all the solvers (r2 > 0.99) and 1.4% for the two commercial codes. The average of the root mean squared error against the experimental results was 134.5% (r2 = 0.29) for the generic model and 13.8% (r2 = 0.96) for the specimen-specific models. It was found that composite femurs had variations in cortical thickness around the neck of the femur of up to 48.4%. For the first time, an experimentally validated, finite-element model of the femur is presented for use in three solvers. This model is freely available online along with all the supporting validation data.

Identification of the critical level of implantation of an osseointegrated prosthesis for above-knee amputees

The aim of our study was to identify potential critical levels of implantation of an osseointegrated prosthesis for above-knee amputees. The implant used was the OPRA system. It was inserted in the femur at four different amputation heights, characterized by their residual limb ratios (0.299, 0.44, 0.58 and 0.73). The stress and strain distribution was evaluated in the bone-implant system during walking, considering a body mass of 100 kg. Considerably high stimulus (11,489 με) in the tissue near the tip was found at the highest implantation level. All models presented small non-physiologic stress values in the tissue around the implant. The results revealed that the implantation level has a decisive effect on bone-implant performance. Mainly, the analysis indicates adverse biomechanical conditions for implantations in very short residual limbs.

Mechanical bone growth stimulation by magnetic fibre networks obtained through a competent finite element technique

Fibre networks combined with a matrix material in their void phase make the design of novel and smart composite materials possible. Their application is of great interest in the field of advanced paper or as bioactive tissue engineering scaffolds. In the present study, we analyse the mechanical interaction between metallic fibre networks under magnetic actuation and a matrix material. Experimentally validated FE models are combined for that purpose in one joint simulation. High performance computing facilities are used. The resulting strain in the composite’s matrix is not uniform across the sample volume. Instead we show that boundary conditions and proximity to the fibre structure strongly influence the local strain magnitude. An analytical model of local strain magnitude is derived. The strain magnitude of 0.001 which is of particular interest for bone growth stimulation is achievable by this assembly. In light of these findings, the investigated composite structure is suitable for creating and for regulating contactless a stress field which is to be imposed on the matrix material. Topics for future research will be the advanced modelling of the biological components and the potential medical utilisation.

Biomechanical investigation of titanium elastic nail prebending for treating diaphyseal long bone fractures

This study numerically investigated the deformation of titanium elastic nails prebent at various degrees during implantation into the intramedullary canal of fractured bones and the mechanism by which this prebending influenced the stability of the fractured bone. Three degrees of prebending the implanted portions of the nails were used: equal to, two times, and three times the diameter of the intramedullary canal. Furthermore, a simulated diaphyseal fracture with a 5-mm gap was created in the middle shaft portion of the bone fixed with two elastic nails in a double C-type configuration. End caps were simulated using a constraint equation. To confirm that the simulation process is able to present the mechanical response of the nail inside the intramedullary, an experiment was conducted by using sawbone for validation. The results indicated that increasing the degrees of nail prebending facilitated straightening the nails against the inner aspect of canal after implantation, with increase in stability under torsion. Furthermore, reducing nail prebending caused a larger portion of the nails to move closer to the loading site and center of bone after implantation; the use of end caps prevented the nail tips from collapsing and increased axial stability. End cap use was critical for preventing the nail tips from collapsing and for increasing the stability of the nails prebent at a degree equal to the diameter of the canal with insufficient frictional force between the nail and canal. Therefore, titanium elastic nail prebending in a double C-type configuration with a degree three times the diameter of the canal represents a superior solution for treating transverse fractures without a gap, whereas that with a degree equal to the diameter of the intramedullary canal and combined with end cap use represents an advanced solution for treating comminuted fractures in a diaphyseal long bone fracture.

The Elastic Behaviour of Sintered Metallic Fibre Networks: A Finite Element Study by Beam Theory

Background

The finite element method has complimented research in the field of network mechanics in the past years in numerous studies about various materials. Numerical predictions and the planning efficiency of experimental procedures are two of the motivational aspects for these numerical studies. The widespread availability of high performance computing facilities has been the enabler for the simulation of sufficiently large systems.

Objectives and Motivation

In the present study, finite element models were built for sintered, metallic fibre networks and validated by previously published experimental stiffness measurements. The validated models were the basis for predictions about so far unknown properties.

Materials and Methods

The finite element models were built by transferring previously published skeletons of fibre networks into finite element models. Beam theory was applied as simplification method.

Results and Conclusions

The obtained material stiffness isn’t a constant but rather a function of variables such as sample size and boundary conditions. Beam theory offers an efficient finite element method for the simulated fibre networks. The experimental results can be approximated by the simulated systems. Two worthwhile aspects for future work will be the influence of size and shape and the mechanical interaction with matrix materials.

Selecting boundary conditions in physiological strain analysis of the femur: Balanced loads, inertia relief method and follower load

Selection of boundary constraints may influence amount and distribution of loads. The purpose of this study is to analyze the potential of inertia relief and follower load to maintain the effects of musculoskeletal loads even under large deflections in patient specific finite element models of intact or fractured bone compared to empiric boundary constraints which have been shown to lead to physiological displacements and surface strains. The goal is to elucidate the use of boundary conditions in strain analyses of bones. Finite element models of the intact femur and a model of clinically relevant fracture stabilization by locking plate fixation were analyzed with normal walking loading conditions for different boundary conditions, specifically re-balanced loading, inertia relief and follower load. Peak principal cortex surface strains for different boundary conditions are consistent (maximum deviation 13.7%) except for inertia relief without force balancing (maximum deviation 108.4%). Influence of follower load on displacements increases with higher deflection in fracture model (from 3% to 7% for force balanced model). For load balanced models, follower load had only minor influence, though the effect increases strongly with higher deflection. Conventional constraints of fixed nodes in space should be carefully reconsidered because their type and position are challenging to justify and for their potential to introduce relevant non-physiological reaction forces. Inertia relief provides an alternative method which yields physiological strain results.

Working length of locking plates determines interfragmentary movement in distal femur fractures under physiological loading

BACKGROUND

This study aimed to investigate the influence of the screw location and plate working length of a locking plate construct at the distal femur on interfragmentary movement under physiological loading.

METHODS

To quantitatively analyse the influence of plate working length on interfragmentary movements in a locking plate construct bridging a distal femur fracture, a finite element model based on CT (computed tomography) data was physiologically loaded and fracture gap conditions were calculated. Four working lengths with eight screw variations each were systemically analysed.

FINDINGS

Interfragmentary movements for axial (12-19%, p<0.001) and shear movements (-7.4-545%, p<0.001) at all tested nodes increased significantly with longer plate working length, whereas screw variations within the groups revealed no significant influence. The working length (defined by screw location) dominates the biomechanical fracture gap conditions.

INTERPRETATION

The current finite element analysis demonstrates that plate working length significantly influences interfragmentary movements, thereby affecting the biomechanical consequences of fracture healing.

Strength analysis of clavicle fracture fixation devices and fixation techniques using finite element analysis with musculoskeletal force input

In the cases, when clavicle fractures are treated with a fixation plate, opinions are divided about the best position of the plate, type of plate and type of screw units. Results from biomechanical studies of clavicle fixation devices are contradictory, probably partly because of simplified and varying load cases used in different studies. The anatomy of the shoulder region is complex, which makes it difficult and expensive to perform realistic experimental tests; hence, reliable simulation is an important complement to experimental tests. In this study, a method for finite element simulations of stresses in the clavicle plate and bone is used, in which muscle and ligament force data are imported from a multibody musculoskeletal model. The stress distribution in two different commercial plates, superior and anterior plating position and fixation including using a lag screw in the fracture gap or not, was compared. Looking at the clavicle fixation from a mechanical point of view, the results indicate that it is a major benefit to use a lag screw to fixate the fracture. The anterior plating position resulted in lower stresses in the plate, and the anatomically shaped plate is more stress resistant and stable than a regular reconstruction plate.

Finite element analysis of the effect of cannulated screw placement and drilling frequency on femoral neck fracture fixation

BACKGROUND

Positioning of the implanted cannulated screw is paramount for stable femoral neck fracture fixation. To avoid overdrilling, the aim of this study is to determine the optimum configuration of three cannulated screws employed in femoral neck fracture fixation.

METHODS

Using a CT scan from a 28 year old healthy male, several models of femoral neck fracture fixation were developed using finite element analysis. After drilling small holes (in either fixed or random patterns) for screw insertion, the mechanical stresses on the screws were compared for three fracture types.

RESULTS

The inverted isosceles triangle was found to be the best screw configuration. Using finite element analysis, the upper limit of drilling frequency and the maximum stress on the screws for 30°, 50°, and 70° drilling were 14, 16, and 19 times and 46.1MPa, 61.9MPa, and 51.0MPa, respectively. The upper limit of drilling frequency and the maximum stress on the screws for subcapital type, transcervical type, and basicervical type were 14, 16, and 40 times and 24.7MPa, 61.9MPa, and 113.5MPa, respectively.

CONCLUSIONS

Results of this study had supported the use of the inverted isosceles triangle as the best screw configuration for femoral neck fracture fixation. Screw position, Pauwels angle, and drilling frequency can all affect the mechanical strength of femoral neck fracture fixation.

Biomechanical analysis and clinical effects of bridge combined fixation system for femoral fractures

This work aimed to compare the stress distribution and mechanical properties of our bridge combined fixation system and commonly used metal locking plate screw system by finite element analysis and by using the Zwick/Z100 testing machine. In addition, we also investigated the clinical outcome of our bridge combined fixation system for femoral fractures in 59 patients from June 2005 to January 2013. As a result, the stress distribution in the bone plate and screws of metal locking plate screw system during walking and climbing stairs was significantly lower than that of metal locking plate screw system. No significant difference in the displacement was observed between two systems. The equivalent bending stiffness of bridge combined fixation system was significantly lower than that of metal locking plate screw system. There were no significant differences in the bending strength, yield load, and maximum force between two systems. All the cases were followed up for 12-24 months (average 18 months). The X-ray showed bone callus was formed in most patients after 3 months, and the fracture line was faint and disappeared at 6-9 months postoperatively. No serious complications, such as implant breakage and wound infection, occurred postoperatively. According to self-developed standard for bone healing, clinical outcomes were rated as excellent or good in 55 out of 59 patients (success rate: 93.2%). Therefore, our findings suggest that our bridge combined fixation system may be a promising approach for treatment of long-bone fractures.

Three-dimensional finite element analysis used to compare six different methods of syndesmosis fixation with 3.5- or 4.5-mm titanium screws: a biomechanical study

BACKGROUND

Use of thicker and longer (four cortices) screws or of multiple screws seems to be more stable and efficient for syndesmosis fixation.

METHODS

A three-dimensional finite element model of an ankle was constructed from serial axial sections from an existing two-dimensional computed tomographic image. Constructions of syndesmosis fixation with 3.5-mm single tricortical, 3.5-mm single quadricortical, 3.5-mm double tricortical, 3.5-mm double quadricortical, 4.5-mm single tricortical, and 4.5-mm single quadricortical screws were performed on this model. Physiologic loads approximating those during stance phase normal walking were applied to this ankle system. Stress values on the screws using the six fixation methods were compared.

RESULTS

The highest maximum stress was determined over 3.5-mm cortical screws applied as single quadricortical, and the lowest maximum stress was determined over the 4.5-mm cortical screw applied as single quadricortical. Stress on the 3.5-mm single screw with quadricortical application was found to be higher than that with tricortical application and also compared with the 4.5-mm quadricortical screw application. Differences between the 4.5-mm single tricortical and quadricortical screws and between the 3.5-mm single tricortical and 3.5-mm double tricortical screw applications were not significant.

CONCLUSIONS

Quadricortical application of 3.5-mm single screws and tricortical application of 3.5-mm double cortical screws are not good choices for syndesmosis fixation. If the plan is tricortical application, a 3.5-mm single cortical screw is adequate. If quadricortical application of syndesmosis fixation is planned, a 4.5-mm cortical screw should be used.

Comparative study of three models of extra-articular distal humerus fracture osteosynthesis using the finite element method on an osteoporotic computational model

INTRODUCTION

The biomechanical properties of extra-articular fractures of the distal humerus have not been researched sufficiently. The aim of the study was to examine three different models of osteosynthesis for extra-articular distal humerus fractures. Osteosynthesis with two parallel or perpendicular plates is a common method of osteosynthesis for those fractures. We wanted to examine the biomechanical performance of a newly designed Y plate, and compare it to the previously used osteosynthesis methods.

MATERIALS AND METHODS

On an osteoporotic computational model of the distal humerus, a 10 mm gap was made, 25 mm above the olecranon fossa, and osteosynthesis was performed with the newly designed Y-shaped plate and with 3.5 reconstruction plates in parallel and perpendicular configuration. The numerical simulations in axial compression, bending and varus loading were conducted using the finite element method.

RESULTS

On all models the largest displacements in the area of the fracture gap appear around the lower anterior edge. The parallel plate construct had the highest stiffness among the three plating techniques in axial compression. In bending and varus loading the construct with the newly designed plate had the highest stiffness, but in axial compression demonstrated the lowest. The parallel plate configurations had higher stiffness than the perpendicular ones in all three loading directions and the difference is most pronounced in axial compression.

CONCLUSION

The displacements that appeared in all three plating systems are minimal and within the limits that meet the requirements of sufficient biomechanical stability in the usual time for the healing of fractures in that region. The newly designed Y-shaped plate for extra-articular fractures of the distal humerus is a possible alternative to the usual method of osteosynthesis with two plates in the case of an extra-articular fracture of the distal humerus. Further biomechanical studies are needed for a decisive conclusion.

Evaluation of a new approach for modelling the screw–bone interface in a locking plate fixation: A corroboration study

Computational modelling of the screw–bone interface in fracture fixation constructs is challenging. While incorporating screw threads would be a more realistic representation of the physics, this approach can be computationally expensive. Several studies have instead suppressed the threads and modelled the screw shaft with fixed conditions assumed at the screw–bone interface. This study assessed the sensitivity of the computational results to modelling approaches at the screw–bone interface. A new approach for modelling this interface was proposed, and it was tested on two locking screw designs in a diaphyseal bridge plating configuration. Computational models of locked plating and far cortical locking constructs were generated and compared to in vitro models described in prior literature to corroborate the outcomes. The new approach led to closer agreement between the computational and the experimental stiffness data, while the fixed approach led to overestimation of the stiffness predictions. Using the new approach, the pattern of load distribution and the magnitude of the axial forces, experienced by each screw, were compared between the locked plating and far cortical locking constructs. The computational models suggested that under more severe loading conditions, far cortical locking screws might be under higher risk of screw pull-out than the locking screws. The proposed approach for modelling the screw–bone interface can be applied to any fixation involved application of screws.