UV/O3 treatment as a surface modification of rice husk towards preparation of novel biocomposites

Plant-based calcium silicate from rice husk ash: A green adsorbent for free fatty acid recovery from waste frying oil

Driven by the urgent need for a solution to tackle the surge of rice husk (RH) and waste frying oil (WFO) waste accumulation at a global scale, this report highlights the use of calcium silicates (CS) extracted from acid-pre-treated rice husk ash (RHA) for free fatty acid (FFA) removal from WFO as conventional RHA shows limited FFA adsorption performance. A novel alkaline earth silicate extraction method from acid-pre-treated RHA was outlined. The structural and behavioural attributes of the synthesised CS were identified through BET, SEM-EDS, and XRD analyses and compared to those of RHA. Notable morphology and structural modification were determined, including reducing specific surface areas, mitigating from amorphous to crystalline structure with regular geometric forms, and detecting Si-O-Ca functional groups exclusive to CS adsorbents. A comparison study showed superior lauric acid (LA) adsorption performance by CS absorbents over acid-pre-treated RHA, with a significant increase from 0.0831 ± 0.0004 mmol LA/g to 2.5808 ± 0.0011 mmol LA/g after 60 min. Recognised as the best-performing CS adsorbent, CS-1.0 was used for further investigations on the effect of dosage, LA concentration, and temperature for efficient LA adsorption, with up to 100% LA removal and 5.6712 ± 0.0016 mmol LA/g adsorption capacity. The adsorption isotherm and kinetic studies showed LA adsorption onto CS-1.0 followed Freundlich isotherm with KF = 0.0598 mmol(1-1/n) L(1/n) g-1 & Qe,cal = 3.1696 mmol g-1 and intraparticle diffusion model with kid = 0.1250 mmol g-1 min0.5 & Ci = 0.9625 mmol g-1, indicating rapid initial adsorption and involvement of carboxylate end of LA and the calcium ions on the CS-1.0 in the rate-limiting step. The high equilibrium adsorption capacity and LA adsorption rate indicated that the proposed CS-1.0 adsorbent has excellent potential to recover FFA from WFO effectively.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Recent Progress of Rice Husk Reinforced Polymer Composites: A Review

Recently, because of the rising population, carbon overloading, and environmental distress, human beings have needed to increase awareness and responsibility for the reduction of agricultural waste. The utilization of agricultural waste as a filler material in reinforced polymers is a fascinating discovery. This review paper attempts to study the physical, mechanical, and thermal behavior of rice husk (RH) as a fiber for reinforcing various synthetic polymers, based on recent studies, conducted between 2017 and 2021. It also highlights that advanced modification techniques could further improve the performance of composites by tailoring the physical and chemical substances of the fiber or matrix. The thermal properties, including flame-retardance and thermal behavior, are also discussed. The characteristics of the fiber–matrix interaction between RH and the polymer matrix provide essential insights into the future-ready applications of this agricultural waste fiber. The way forward in researching RH polymer composites is finally reviewed.

Current State and Challenges of Natural Fibre-Reinforced Polymer Composites as Feeder in FDM-Based 3D Printing

As one of the fastest-growing additive manufacturing (AM) technologies, fused deposition modelling (FDM) shows great potential in printing natural fibre-reinforced composites (NFRC). However, several challenges, such as low mechanical properties and difficulty in printing, need to be overcome. Therefore, the effort to improve the NFRC for use in AM has been accelerating in recent years. This review attempts to summarise the current approaches of using NFRC as a feeder for AM. The effects of fibre treatments, composite preparation methods and addition of compatibilizer agents were analysed and discussed. Additionally, current methods of producing feeders from NFRCs were reviewed and discussed. Mechanical property of printed part was also dependent on the printing parameters, and thus the effects of printing temperature, layer height, infill and raster angle were discussed, and the best parameters reported by other researchers were identified. Following that, an overview of the mechanical properties of these composites as reported by various researchers was provided. Next, the use of optimisation techniques for NFRCs was discussed and analysed. Lastly, the review provided a critical discussion on the overall topic, identified all research gaps present in the use of NFRC for AM processes, and to overcome future challenges.

Influence of different surface treatment techniques on properties of rice husk incorporated polymer composites

Rice husk natural fiber remains a highly abundant, eco-friendly and low-cost reinforcement filler for plastic composites fabrication. Hampered by its low aspect ratio and incompatibility with non-polar polymers, its utilization in reinforcing polymer composites often results in decreased composite properties such as decreased tensile strength, impact strength, percentage elongation, and flexural strength. However, stiffness increases. Various surface treatment techniques such as mercerization, compatibilization, acetylation, electron beam irradiation and plasma surface modification have been employed to improve its compatibility with non-polar matrix polymers. This article critically reviews the influence of these surface modification techniques on the resulting composite properties. Based on the analysis of reinforcing efficiencies of these techniques, their strengths, weaknesses, opportunities, and threats, the authors, therefore, project plasma treatment as the most efficient and eco-friendly technique with prospects for high technological application of rice husk plastic composites.

Fabrication of Porous Recycled HDPE Biocomposites Foam: Effect of Rice Husk Filler Contents and Surface Treatments on the Mechanical Properties

In this study, a biodegradable, cheap and durable recycled high-density polyethylene (rHDPE) polymer reinforced with rice husk (RH) fibre was fabricated into a foam structure through several processes, including extrusion, internal mixing and hot pressing. The effect of filler loading on the properties of the foam and the influence of RH surface treatments on the filler–matrix adhesion and mechanical properties of the composite foam were investigated. The morphological examination shows that 50 wt.% filler content resulted in an effective dispersion of cells with the smallest cell size (58.3 µm) and the highest density (7.62 × 1011 sel/cm³). This small cell size benefits the mechanical properties. Results indicate that the tensile strength and the Young’s modulus of the alkali-treated RH/rHDPE composite foam are the highest amongst the treatments (10.83 MPa and 858 MPa, respectively), followed by UV/O₃, which has shown considerable increments compared with the untreated composite. The flexural and impact tests also show the increment in strength for the composite foam after chemical treatment. Although the UV/O₃ surface treatment has minor influence on the mechanical enhancement of the composite foam, this method may be a reliable surface treatment of the fibre-reinforced composite.

Treated rice husk as a recyclable sorbent for the removal of microcystins from water

Microcystins (MCs) appear during harmful algal blooms (HABs) in water sources worldwide, and represent a threat for humans and animals ingesting or inhaling MCs from the environment. Herein, treated rice husk (RH) was tested as a recyclable sorbent for removal of six MCs (MC-RR, MC-LR, MC-YR, MC-LA, MC-LF, and MC-LW) from water. RH was refluxed with hydrochloric acid and heated to 250 °C to produce the sorbent material. Twenty milligrams of treated RH removed >95% of the MCs from a 30 mL solution containing 25 μg/L of each MC. The adsorption of MCs onto RH follows the Freundlich isotherm model (R² ≥ 0.9612) and pseudo-second-order kinetics (R² ≥ 0.9996). More than 90% of MCs were removed within 5 min, and >95% were removed at equilibrium (in <40 min). Performance of the RH sorbent was evaluated by removing MCs from Lake Erie water collected during an algal bloom in 2017. The total concentration (extracellular plus intracellular) of six tested MCs in lake water ranged from 3.7 to 13,605.9 μg/L, and removal of MCs by treated RH ranged from 100.0% to 71.8%, respectively. The removal capacity of RH for the six MCs from the lake water sample containing 13,605.9 μg/L of MCs was 586 μg per g of treated RH. After being used to extract MCs, the RH was heated to 560 °C to produce silica nanoparticles. Therefore, treated RH enables rapid and efficient removal of MCs from water and it can be recycled for use as a raw material. Overall, treated RH can contribute to mitigation of environmental and health effects caused by MCs and reduce concerns for toxic waste disposal.