Bone Response to Submerged, Unloaded Implants Inserted in Poor Bone Sites: A Histological and Histomorphometrical Study of 8 Titanium Implants Retrieved From Man

Modelling the resonant frequency associated with the spatio-temporal evolution of the bone-dental implant interface

Dental implant stability is greatly affected by the mechanical properties of the bone-implant interface (BII), and it is key to long-term successful osseointegration. Implant stability is often evaluated using the Resonant Frequency Analysis (RFA) method, and also by the quality of this interface, namely the bone-implant contact (BIC). True to this day, there is a scarcity of models tying BIC, RFA and a spatially and mechanically evolving BII. In this paper, based on the contact/distance osteogenesis concept, a novel numerical spatio-temporal model of the implant, surrounding bone and evolving interface, was developed to assess the evolution of the interfacial stresses on the one hand and the corresponding resonant frequencies on the other. We postulate that, since the BIC percentage reaches saturation over a very short time, long before densification of the interface, it becomes irrelevant as to load transmission between the implant and the bone due to the existence of an open gap. Gap closure is the factor that provides continuity between the implant and the surrounding bone. The results of the calculated RFA evolution match and provide an explanation for the multiple clinical observations of a sharp initial decline in RFA, followed by a gradual increase and plateau formation. STATEMENT OF SIGNIFICANCE: A novel three-dimensional numerical model of an evolving bone-dental implant interface (BII) is presented. The spatio-temporal evolution of the bone-implant contact (BIC) and the BII, based on contact/distance (CO/DO) osteogenesis, is modeled. A central outcome is that, until BII maturation into a solid continuous bone (no open gap between CO-DO fronts), the bone-implant load transfer is hampered, irrespective of the BIC. The resonant frequencies' evolution of the jawbone-BII-implant is calculated to reproduce the well-established implant stability analysis based on the Resonant Frequency Analysis. The results resemble those reported clinically, and here too, the determinant transition occurs only after interfacial gap closure. Those results should motivate clinicians to re-consider structural continuity of the BII rather than the BIC only.

Implant primary stability with an osteocondensation drilling protocol in different density polyurethane blocks

The implant primary stability is a fundamental condition for avoiding implant micro-motions that might result in fibrous encapsulation; its achievement is facilitated by macro- and micro-geometry of the implant, and by the bone density and architecture at the intended implant site. The aim was to evaluate an osteocondensing drilling protocol for dental implant positioning compared to standard protocol on polyurethane block. A total of 40 implants, 20 for each osteocondensing group (Test) and 20 for standard drilling group (Control), were positioned. Insertion torque (IT), removal torque (RT), and Periotest were measured. A IT, RT, and Periotest significant difference was present in favor of the implant osteocondensing protocol. The results suggested that osteocondensing protocol represents a useful technique for implant placement in poor density bone.

Osseointegration around dental implants biofunctionalized with TGFβ-1 inhibitor peptides: an in vivo study in beagle dogs

The aim of this study was to evaluate the effect of biofunctionalization with two TGF-β1 inhibitor peptides, P17 and P144, on osseointegration of CP-Ti dental implants. A total of 36 implants (VEGA, Klockner®) with 3.5 × 8 mm internal connection were used in this study, divided in three groups: (1) control group (n = 12), (2) implants which surfaces were biofunctionalized with P17 peptide inhibitor (n = 12), (3) implants with surfaces biofunctionalized by P144 peptide (n = 12). Three implants, one from each group, were inserted in both hemimandibles of 6 beagle dogs, 2 months after tooth extraction. Two animals were sacrificed at 2, 4 and 8 weeks post implant insertion, respectively. The samples were analyzed by Backscattering Scanning Electron Microscopy (BS-SEM) and histological analysis. Histomorphometric analysis of bone to implant contact (BIC), peri-implant bone fraction (BF) and interthread bone (IB) were carried out. Bone formation around implants measured by quantitative analysis, BS-SEM, was significantly higher in the P17-biofunctionalized implants, 4 and 8 weeks after the implantation. Histomorphometric analysis of BIC, BF and IB showed higher values in the P17-biofunctionalized group at initial stages of healing (2 weeks) and early osseointegration both at 4 and 8 weeks. For P144 biofunctionalized implants, the histomorphometric values obtained are also higher than control group. Accordingly, better results in the experimental groups were proven both by the quantitative and the qualitative analysis. Surface biofunctionalization with TGF-β1 inhibitor peptides, P17 and P144, resulted in better quantitative and qualitative parameters relative to implant osseointegration.

A Narrative Review of the Histological and Histomorphometrical Evaluation of the Peri-Implant Bone in Loaded and Unloaded Dental Implants. A 30-Year Experience (1988-2018)

Background: The aim of the present review was to assess the histological and histomorphometrical data from the paper published by our Laboratory on peri-implant bone in dental implants in different loading conditions. Methods: The papers published in different implant loading conditions, in dental implants retrieved from humans, and in the Hard Tissues Research Center of the University of Chieti-Pescara, Italy, were screened on MEDLINE/PubMed, Embase, Scopus, and other electronic databases until 31 December 2018. Only articles that reported the histological and histomorphometrical values of the Bone-Implant Contact (BIC) were selected. Results: The system selection provided a total of 155 papers. The manuscripts included for the narrative review were 57. These papers provided histological and histomorphometrical data. Conclusions: The bone remodeling around dental implants was found to be a dynamic process; loading changed the microstructure of the peri-implant bone; and implants were found to provide a successful function, over several decades, with different range of degrees of BIC in vivo (varying from a little more than 30% to a little more than 90%). Loaded implants presented a 10%-12% higher BIC values when compared to submerged, unloaded implants, and rougher surfaces had, on average, about a 10% higher BIC than machined surfaces.

Periimplant Bone Response in Human-Retrieved, Clinically Stable, Successful, and Functioning Dental Implants After a Long-Term Loading Period: A Report of 17 Cases From 4 to 20 Years

OBJECTIVE

This study aimed at a histologic and histomorphometric analysis of the periimplant tissues and bone-titanium interface reactions in successfully osseointegrated, clinically stable, and immobile human titanium dental implants retrieved after a long loading period.

MATERIALS AND METHODS

In the last 30 months (2013-2015), 21 implants, retrieved from individuals for different causes after a loading period ranging from 4 to 20 years, were sent to the Implant Retrieval Center, University of Chieti-Pescara, Italy. In 4 cases, almost all the bone had been lost during the retrieval, whereas in the remaining 17 cases, mineralized bone was still present.

RESULTS

Around the majority of the implants, mature compact bone with few marrow spaces was found. The trabecular bone, constituted by a few thin bone trabeculae, was in a periimplant location around only a few implants. A high percentage of bone-implant contact (BIC) (comprised between 32 ± 4.1% and 83 ± 2.9%) was present. In almost all implants, the space within the threads was almost completely filled by compact lamellar bone or by a thin layer of bone. Close and tight contact between bone and implant surface was observed in all specimens with no gaps or connective tissue at the interface.

CONCLUSIONS

All implants appeared to be well integrated in the surrounding mineralized bone, and all of them showed adequate bone-to-implant contact percentages.

A randomized, 12-month controlled trial to evaluate non-inferiority of early compared to conventional loading of modSLA implants in single tooth gaps

Background

The aim of the study was to evaluate whether early loading of implants with a chemically modified sandblasted, large-grit, acid-etched (SLA) (SLActive®) surface was non-inferior to conventional loading in terms of change in crestal bone level.

Methods

This was a randomized, controlled, multicenter study. Patients requiring single-tooth rehabilitation in the posterior maxilla or mandible received implants and were randomized to receive a provisional restoration in occlusal load after 25 ± 3 days (early loading) or after 13 ± 1 weeks (conventional loading). The primary endpoint was change in crestal bone level between implant placement (baseline) and 6 months. Secondary endpoints included change in crestal bone level between baseline and 12 months, implant survival and success rates, and patient satisfaction.

Results

Of the 84 patients enrolled, 78 received implants and were randomized onto the early loading (41 patients) and conventional loading (37 patients) groups. The mean change in crestal bone level between baseline and 6 months was 0.56 ± 0.58 and 0.51 ± 0.62 mm for early and conventional loading, respectively; at 12 months, the mean change was 0.76 ± 0.60 and 0.73 ± 0.77 mm, respectively. Implant survival and success at 12 months were 100 % for both groups. Patient satisfaction was similar between the groups, except that more patients in the early loading group were satisfied or highly satisfied with the time taken for fitting.

Conclusion

The study demonstrated that early implant loading was non-inferior to conventional implant loading in terms of crestal bone level change in a Japanese patient population in short follow-up period and single tooth gaps in molar regions.

Anatomical Remodeling of Buccal Bone Plate in 35 Premaxillary Post-Extraction Immediately Restored Single TPS Implants: 10-Year Radiographic Investigation

PURPOSE

The anatomical remodeling technique (ART) was proposed to place postextraction implants with the aid of specific osteotomes. This study is a clinical and radiographic evaluation with 10-year follow-up of anterior postextraction single implants placed with the ART and immediately restored.

MATERIALS AND METHODS

Thirty-five patients, with a hopeless tooth in the anterior maxilla, were included in the study and 35 implants were inserted according to the ART. Clinical and radiographic evaluations were performed at baseline (T0), after 6 (T1) and 14 months (T2), 4 years after surgery (T3) and every other year up to the 10-year follow-up (T4, T5, and T6). Implant success, survival, and failure rates were evaluated according to the International Congress of Oral Implantologists Pisa Consensus Conference criteria.

RESULTS

Twenty-nine patients and 29 implants were available for the 10-year data analysis. After 10 years, the accumulated mean marginal bone loss was 2.69 ± 0.42 mm. The cumulative survival rate of the implants was 100%.

CONCLUSIONS

Immediately loaded postextractive implants, placed according to the ART, have been proved to be a predictable method to rehabilitate single tooth in the anterior maxilla.

[Analysis of volume and costs of dental care provided in outpatient settings]

A conducted analysis of volume and cost of dental care provided in outpatient settings proves the need for harmonization of Russian Ministry of Health's documentation regulating dental checks in adults and children, and the Programme of state guarantees.

Human study of ion implantation as a surface treatment for dental implants

This clinical study evaluated a new surface treatment of ion implantation with CO ions which has previously been subjected to extensive study in animal models. The aim of this work was to assess its effect in humans. Experimental mini-implants were used; half of their longitudinal surface was machined and the other half was treated with CO ion implantation. The study was conducted in healthy volunteer patients who required prosthetic treatment with dental implants, and in accordance with the corresponding ethics committees. Coinciding with the insertion of commercial implants for oral restoration, one or two mini-implants were placed in the upper maxillary tuberosity or in the retromolar trigone of the mandible. The mini-implants were removed with a trephine jointly with a small volume of surrounding bone after a 3-month period. Two evaluation methods were used and both showed a greater degree of bone integration in the mini-implant section that underwent CO ion implantation treatment in comparison with the non-treated surface: 62.9% vs. 57.9%, and 54.8% vs. 46.2%. In addition, no adverse reactions were observed in the surface treatment with CO ion implantation. These results confirm the positive benefits in humans, based on the findings obtained from previous animal experiments.

A retrospective study on related factors affecting the survival rate of dental implants

PURPOSE

The aim of this retrospective study is to analyze the relationship between local factors and survival rate of dental implant which had been installed and restored in Seoul Veterans Hospital dental center for past 10 years. And when the relationship is found out, it could be helpful to predict the prognosis of dental implants.

MATERIALS AND METHODS

A retrospective study of patients receiving root-shaped screw-type dental implants placed from January 2000 to December 2009 was conducted. 6385 implants were placed in 3755 patients. The following data were collected from the dental records and radiographs: patient's age, gender, implant type and surface, length, diameter, location of implant placement, bone quality, prosthesis type. The correlations between these data and survival rate were analyzed. Statistical analysis was performed with the use of Kaplan-Meier analysis, Chi-square test and odds ratio.

RESULTS

In all, 6385 implants were placed in 3755 patients (3120 male, 635 female; mean age 65 ± 10.58 years). 108 implants failed and the cumulative survival rate was 96.33%. There were significant differences in age, implant type and surface, length, location and prosthesis type (P<.05). No significant differences were found in relation to the following factors: gender, diameter and bone quality (P>.05).

CONCLUSION

Related factors such as age, implant type, length, location and prosthesis type had a significant effect on the implant survival.

In vivo evaluation of micro-rough and bioactive titanium dental implants using histometry and pull-out tests

We report on the in vivo histological and mechanical performance of titanium dental implants with a new surface treatment (2Step) consisting of an initial grit-blasting process to produce a micro-rough surface, followed by a combined chemical and thermal treatment that produces a potentially bioactive surface, i.e., that can form an apatitic layer when exposed to biomimetic conditions in vitro. Our aim was to assess the short- and mid-term bone regenerative potential and mechanical retention of 2Step implants in mandible and maxilla of minipigs and compare them with micro-rough grit-blasted, micro-rough acid-etched, and smooth as-machined titanium implants. The percent of bone-to-implant contact after 2, 4, 6, and 10 weeks of implantation as well as the mechanical retention after 4, and 6 weeks of implantation were evaluated with histometric and pull-out tests, respectively, as a measure of the osseointegration of the implants. We also aimed to assess the bioactive nature of 2Step surfaces in vivo. Our results demonstrated that the 2Step treatment produced micro-rough and bioactive implants that accelerated bone tissue regeneration and increased mechanical retention in the bone bed at short periods of implantation in comparison with all other implants tested. This was mostly attributed to the ability of 2Step implants to form in vivo a layer of apatitic mineral that coated the implant and could rapidly stimulate (a) bone nucleation directly on the implant surface, and (b) bone growing from the implant surface. We also proved that roughness values of Ra≈4.5 μm favoured osseointegration of dental implants at short- and mid-term healing periods, as grit-blasted implants and 2Step implants had higher retention values than as machined and acid-etched implants. The surface quality resulting from the 2Step treatment applied on cpTi provided dental implants with a unique combination of rapid bone regeneration and high mechanical retention.

Effects of implant surface coatings and composition on bone integration: a systematic review

OBJECTIVE

The aim of the present review was to evaluate the bone integration efficacy of recently developed and marketed oral implants as well as experimental surface alterations.

MATERIALS AND METHODS

A PubMed search was performed for animal studies, human reports and studies presenting bone-to-implant contact percentage or data regarding mechanical testing.

RESULTS

For recently developed and marketed oral implants, 29 publications and for experimental surface alterations 51 publications fulfilled the inclusion criteria for this review.

CONCLUSIONS

As demonstrated in the available literature dealing with recently developed and marketed oral implants, surface-roughening procedures also affect the surface chemical composition of oral implants. There is sufficient proof that surface roughening induces a safe and predictable implant-to-bone response, but it is not clear whether this effect is due to the surface roughness or to the related change in the surface composition. The review of the experimental surface alterations revealed that thin calcium phosphate (CaP) coating technology can solve the problems associated with thick CaP coatings, while they still improve implant bone integration compared with non-coated titanium implants. Nevertheless, there is a lack of human studies in which the success rate of thin CaP-coated oral implants is compared with just roughened oral implants. No unequivocal evidence is available that suggests a positive effect on the implant bone integration of peptide sequences or growth factors coated on titanium oral implants. In contrast, the available literature suggests that bone morphogenetic protein-2 coatings might even impede the magnitude of implant-to-bone response.

Characteristic features of trabecular bone in edentulous mandibles

BACKGROUND

The density and architecture of the alveolar trabecular bone are crucial to the stability of an endosseous implant. A significantly higher implant failure rate can be expected when implants are placed in alveolar bone with reduced density and stability. Therefore, the present study aimed to describe the trabecular bone structure of edentulous mandibles.

METHOD

Two hundred and seventy-eight bone sections, including the lateral incisor, first premolar, and first molar regions, were obtained from 128 edentulous lower jaws (68 females and 60 males; mean age: 77.58 years). Ground sections were prepared for each region using the 'sawing and grinding' technique. The following standard structural histomorphometric parameters were determined using a semiautomatic image analysis: trabecular bone volume, trabecular thickness, trabecular number, trabecular separation, and the trabecular bone pattern factor, which describes the connectedness of cancellous bone structures. Also, the maximum height of the jaw section was determined, to detect any possible correlations between vertical height and histomorphometric parameters.

RESULTS

All the histomorphometric parameters examined showed an unexpectedly huge range of variation. The mean trabecular bone volume ranged between 20.9% and 36.9%. The mean trabecular thickness showed values between 165.9 and 224.7 microm. The mean trabecular number ranged between 1.22 and 1.77/ mm, and the mean trabecular separation ranged between 436.7 and 720.0 microm. The mean trabecular bone pattern factor showed values between -0.05 and -3.01/ mm. The maximum height of the jaw sections showed values between 16.05 and 23.42 mm. The trabecular bone volume, thickness, number and connectivity were significantly lower in the molar region than in the incisal and premolar regions. Significant sex-specific differences were found in all the regions, female mandibles showing a smaller amount and lower connectivity of cancellous bone than male mandibles. No correlation could be found between the maximum height of the jaw and the histomorphometric parameters of the cancellous bone.

CONCLUSION

A possible explanation for the difference in the density between the incisal and the molar region may be that molars are generally lost at an earlier age than anterior and premolar teeth. As a result, atrophy-related resorptive and remodeling processes commence earlier and progress further in this region than in the anterior and premolar regions. Sex-specific differences are probably due to an increased postmenopausal bone loss of the females.

In vivo low-density bone apposition on different implant surface materials

During osseointegration, new bone may be laid down on the implant surface and/or on the old bone surface; the former is known as contact osteogenesis and the latter as distance osteogenesis. Implant surface topography and material composition affect this process. The present study evaluates Ca and P apposition onto three different dental implant material surfaces (carbon monoxide (CO) ion implantation on Ti6Al4V, sand blasting and acid etching on commercially pure titanium and untreated Ti6Al4V) on the mandibles of beagles after healing periods of 3 and 6 months. Energy dispersive spectroscopy is useful for identifying low-density bone relative to surrounding mature bone, allowing for discrimination of the osteogenesis source. Low-density bone was only found at the apical end; there was none on the surface of untreated implants. Low-density bone arising from mature bone towards the implant at month 3 (i.e. distance osteogenesis) was only present on the CO ion implanted samples, due to the modification of the surface nano-topography and the chemistry and structure of the material.

Implant Zones of the Jaws: Implant Location and Related Success Rate

The article demonstrates the factors of importance in the early and late failures of dental implants based on literature review. An implant location is one of many factors that can influence a success or failure of dental implants. The author identifies and describe four alveolar jaw regions--functional implant zones--with unique characteristics of anatomy, blood supply, pattern of bone resorption, bone quality and quantity, need for bone grafting and other supplemental surgical procedures, and a location-related implant success rate. The article discusses predisposing factors that can lead to early implant failures in different jaw zones. An implant location is investigated as one of these factors. A prior history of trauma to premaxillary region is described in the context of implant success in anterior maxilla. This zone is being referred by the author as the "traumatic zone." The challenges of mandibular posterior implant reconstruction are presented in the context of blood supply to the mandible. A deficiency of vascularization in this region, especially in elderly and edentulous patients, lead the author to refer to this zone as the "ischemic zone." The concept of relative ischemia of the posterior mandible that can develop with age and tooth loss is discussed. A thorough understanding of specifics of each functional implant zone should help to improve successes and prevent failures of dental implants.

In vitro osteogenesis on a microstructured titanium surface with additional submicron-scale topography

The present study aimed to evaluate key parameters of in vitro osteogenesis on (1) commercially pure titanium (cpTi) discs with 20-200-microm-scale microtopography patterned with additional micron- and submicron-scale topography (0.5-20 microm; Plus surface, Dentsply Friadent), (2) control cpTi discs with 20-200-microm-scale microtopography (DPS, Deep Profile Surface, Dentsply Friadent), and (3) a machined surface. Using calvaria-derived osteogenic cultures, the following parameters were assessed: cell adhesion and spreading, growth curve and cell viability, alkaline phosphatase (ALP) activity and total protein content, immunolocalization of fibronectin, bone sialoprotein (BSP) and osteopontin (OPN), and bone-like tissue formation. The results showed no major differences between surfaces in terms of cell adhesion, growth curve, cell viability (days 4 and 11), ALP activity, or total protein content (days 11 and 17). At day 11, cultures grown on Plus exhibited small, well-defined nodular areas of calcified matrix, which were only rarely observed on DPS and absent on the machined surface. Such areas were larger at day 17 and were not associated with the typical mineralized bone-like nodules (with BSP- and OPN-positive osteoblastic cells on top). At day 17, the total mineralized area was significantly larger on DPS than on a Plus or machined surface (DPS>Plus>machined; Kruskal-Wallis test, P<0.05). Direct fluorescence allowed the straightforward observation of higher amounts of apoptotic bodies associated with mineralized nodules for Plus. The results suggested the occurrence of an additional, early pattern of matrix mineralization mostly for the Plus microstructured surface, which did not necessarily translate into larger bone-like tissue formation in vitro.

Dental implant success-failure analysis: a concept of implant vulnerability

This article shows the factors of importance in the long-term success and failure of oral implants based on literature review. Many factors are attributed to the failure of dental implants. The critical components leading to early and late implant failures are evaluated. The behavior of natural teeth and implants is compared in healthy and unfavorable local and systemic conditions. Similarities and differences among dental implants, healthy natural teeth, and ankylosed teeth are examined. Based on this comparison, the author attempts to draw a conclusion on the vulnerability of dental implants and their prognosis. The importance of ongoing clinical supervision of a patient's implant condition with a good recall program and the necessity to accumulate clinical data concerning implant failures over an extended period of time in a standardized manner are emphasized. It is also suggested that implant practitioners avoid giving guarantees of long-term implant success to their patients.

Randomized, Controlled Histologic and Histomorphometric Evaluation of Implants With Nanometer-Scale Calcium Phosphate Added to the Dual Acid-Etched Surface in the Human Posterior Maxilla

BACKGROUND

Placement of dental implants in the posterior maxilla has been associated with higher rates of failure that are due, in part, to the poor bone quality of this region. The purpose of the present study was the histologic and histomorphometric evaluation of the bone around a new implant surface treatment created by a deposition of nanometer-sized calcium phosphate particles added to the dual acid-etched surface.

METHODS

One custom-made 2 x 10-mm site evaluation implant (SEI) with this novel treatment surface (test) and one SEI with the dual acid-etched surface without treatment (control) were placed in the posterior maxilla of 15 patients. All SEIs were retrieved after 2 months and evaluated under confocal laser scanning microscopy (CLSM) and by light microscopy for histomorphometric analysis of the bone-implant contact (BIC).

RESULTS

Histologic observations in control SEIs showed formation of new bone around the implant surface; however, it was not always in direct contact with the entire perimeter of the threads. The mean BIC was 19% +/- 14.2%. Test SEIs showed peri-implant bone tightly contacting the implant surface and better adapted to the threads. Three-dimensional reconstruction of sections obtained using CLSM showed the intimacy of the contact between bone and test SEI surface through the entire thickness of the specimens. The mean BIC was 32.2% +/- 18.5%.

CONCLUSIONS

After 2 months of healing, comparison of the BIC values showed a statistically significant greater mean BIC for test SEIs than for controls. The clinical implications of these results included shortening of the implant healing period and earlier loading protocols.

Bone density and primary stability in implant therapy

INTRODUCTION

To improve patient comfort, deviations from the very successful standard osseointegration protocol are being developed. To keep implant failure rates as low as possible, the most perfect treatment planning and a good patient selection are extremely important. Because bone density plays an important role in implant outcome, known relations of bone density could improve treatment planning.

MATERIAL AND METHODS

A Pubmed search revealed 66 manuscripts investigating and discussing bone density of human jawbone whether or not related to implant stability or outcome. Forty-five of these will be discussed in this review.

RESULTS AND DISCUSSION

Many pre-operative methods of jawbone density assessment are available. Most of those techniques correlate well with one another. Some are more elaborate to use in clinical practice. Primary stability measurements show significant correlations with different bone densities and also with implant outcome; however, not many studies investigate both at the same time.

CONCLUSION

To investigate the outcome of adaptation methods of the surgical protocol with regard to the jawbone density, an objective pre-surgical determination of bone density is necessary.