Interference with spectrophotometric analysis of nucleic acids and proteins by leaching of chemicals from plastic tubes

Comparison of DeNovix, NanoDrop and Qubit for DNA quantification and impurity detection of bacterial DNA extracts

Accurate DNA quantification is key for downstream application including library preparations for whole genome sequencing (WGS) and the quantification of standards for quantitative PCR. Two commonly used technologies for nucleic acid quantification are based on spectrometry, such as NanoDrop, and fluorometry, such as Qubit. The DS-11+ Series spectrophotometer/fluorometer (DeNovix) is a UV spectrophotometry-based instrument and is a relatively new spectrophotometric method but has not yet been compared to established platforms. Here, we compared three DNA quantification platforms, including two UV spectrophotometry-based techniques (DeNovix and NanoDrop) and one fluorometry-based approach (Qubit). We used genomic prokaryotic DNA extracted from Streptococcus pneumoniae using a Roche DNA extraction kit. We also evaluated purity assessment and effect of a single freeze-thaw cycle. Spectrophotometry-based methods reported 3 to 4-fold higher mean DNA concentrations compared to Qubit, both before and after freezing. The ratio of DNA concentrations assessed by spectrophotometry on the one hand, and Qubit on the other hand, was function of the A260/280. In case DNA was pure (A260/280 between 1.7 and 2.0), the ratio DeNovix or Nanodrop vs. Qubit was close or equal to 2, while this ratio showed an incline for DNA with increasing A260/280 values > 2.0. The A260/280 and A260/230 purity ratios exhibited negligible variation across spectrophotometric methods and freezing conditions. The comparison of DNA concentrations from before and after freezing revealed no statistically significant disparities for each technique. DeNovix exhibited the highest Spearman correlation coefficient (0.999), followed by NanoDrop (0.81), and Qubit (0.77). In summary, there is no difference between DeNovix and NanoDrop in estimated gDNA concentrations of S. pneumoniae, and the spectrophotometry methods estimated close or equal to 2 times higher concentrations compared to Qubit for pure DNA.

Mesenchymal stromal cells derived from various tissues: Biological, clinical and cryopreservation aspects: Update from 2015 review

Mesenchymal stromal cells (MSCs) have become one of the most investigated and applied cells for cellular therapy and regenerative medicine. In this update of our review published in 2015, we show that studies continue to abound regarding the characterization of MSCs to distinguish them from other similar cell types, the discovery of new tissue sources of MSCs, and the confirmation of their properties and functions that render them suitable as a therapeutic. Because cryopreservation is widely recognized as the only technology that would enable the on-demand availability of MSCs, here we show that although the traditional method of cryopreserving cells by slow cooling in the presence of 10% dimethyl sulfoxide (Me2SO) continues to be used by many, several novel MSC cryopreservation approaches have emerged. As in our previous review, we conclude from these recent reports that viable and functional MSCs from diverse tissues can be recovered after cryopreservation using a variety of cryoprotectants, freezing protocols, storage temperatures, and periods of storage. We also show that for logistical reasons there are now more studies devoted to the cryopreservation of tissues from which MSCs are derived. A new topic included in this review covers the application in COVID-19 of MSCs arising from their immunomodulatory and antiviral properties. Due to the inherent heterogeneity in MSC populations from different sources there is still no standardized procedure for their isolation, identification, functional characterization, cryopreservation, and route of administration, and not likely to be a "one-size-fits-all" approach in their applications in cell-based therapy and regenerative medicine.

Investigation of the Effects of Labware Contamination on Mass Spectrometry-Based Human Serum Lipidome Analysis

Polypropylene microcentrifuge tubes (MCTs) are increasingly used in lipidome sample preparation. In the absence of a comprehensive study evaluating ramifications of plasticware utilization in mass spectrometry-based lipidomic analyses, we conducted a systematic analysis to elucidate potential negative effects ascribable to labware contamination in serum lipidomics. During serum lipid extractions, tested glassware introduced 24 labware contaminants. In contrast, Eppendorf polypropylene MCTs contributed 485 contaminant features, many of which could be erroneously putatively identified as lipids via their m/z values. Eppendorf MCTs contamination engendered severe ion-suppression of 40 low abundance serum lipids, while generating mild to modest lipid ion-suppression across a multitude of higher abundance coeluting lipids. Less compatible polypropylene MCTs from an alternative manufacturer introduced a staggering 2,949 contaminant m/z values, severely affecting 75 coeluting serum lipids and causing more frequent and pronounced ion-suppression instances. Furthermore, by performing serum extractions with varied initial volumes, it was ascertained that labware-induced lipid ion-suppression is a dynamic phenomenon, contingent on both lipid and labware contaminant concentrations where low-abundance lipids are disproportionately impacted by coelutes of suppressive contaminants. In addition to lipid ion-suppression, the identification and quantification of 7 fatty acid endogenous serum lipids were compromised by the leaching of structurally identical surfactants from MCTs. MCTs artificially introduced 10 additional primary amides extraneous to serum samples. Utmost caution is imperative in interpreting data concerning primary amides and fatty acids when employing plastic labware. Through this investigation, we aspire to elevate awareness regarding the pernicious impact of labware contamination on lipidome analysis.

Colorimetric Properties of Bombyx mori Silk Fibroin

Recent reports highlighted several novel applications for the Bombyx mori silk fibroin (SF), as edible coatings for the preservation of food freshness, smart labels, or packaging materials. This study complements these reports and additionally describes the colorimetric sensing properties of the natural protein that could be explored to enhance the practical value of such applications. Our data show that in response to pH changes, reconstituted SF is able to undergo visible color changes that correlate with the intensity of the stimuli, regardless of its physical format or physical cross-linking state. The intensity of the developed color was proportional to the extent of the protein's hydrolytic degradation. We also found that these pH-driven color changes were reversible and interchangeable, with colorless samples at neutral pH, purple in acidic environments, and yellow under basic conditions. Our mechanistic studies identified tryptophan as being responsible for these colorimetric responses, which could be further intensified by the presence of ionized tyrosine functionalities. In addition, we determined that SF's sensing properties also applied to ultraviolet light exposure. Finally, we showed that the innate sensing capabilities of activated SF can be enhanced via the covalent incorporation of additional tryptophan into the protein. Overall, our results further support the utility of SF for sensing applications.

Spectrophotometric and nucleic acid-binding properties of halloysite clay nanotubes and kaolinite

Halloysite particles (HNTs) are naturally occurring aluminosilicate nanotubes of low toxicity that have shown great promise for drug and biomolecule delivery into human and animal cells. Kaolinite particles retain the same layered structure as HNT, but do not form nanotubes. In this study, the spectrophotometric and sedimentation properties of the two clays in aqueous solutions and their abilities to associate with both small and large nucleic acids have been investigated. Both clays scattered ultraviolet light strongly and this characteristic of HNT was not affected by either vacuum treatment to remove trapped gases or by sonication. Vacuum treatment increased the binding of small nucleic acids to HNT and this association was further enhanced by addition of divalent metal ions. By contrast, only small RNAs were bound efficiently by kaolinite in the presence of Mg²⁺ ions. Large linear double-stranded DNAs and circular plasmid DNAs bound poorly to kaolinite under all conditions, but these nucleic acids could form strong associations with HNT. Differences in binding data were largely consistent with measurements of the available surface areas of each clay. These results demonstrate that interactions with each clay are critically dependent on both the type and the conformation of each nucleic acid.

Adsorption of bacteriophages on polypropylene labware affects the reproducibility of phage research

Hydrophobicity is one of the most critical factors governing the adsorption of molecules and objects, such as virions, on surfaces. Even moderate change of wetting angle of plastic surfaces causes a drastic decrease ranging from 2 to 5 logs of the viruses (e.g., T4 phage) in the suspension due to adsorption on polymer vials' walls. The effect varies immensely in seemingly identical containers but purchased from different vendors. Comparison of glass, polyethylene, polypropylene, and polystyrene containers revealed a threshold in the wetting angle of around 95°: virions adsorb on the surface of more hydrophobic containers, while in more hydrophilic vials, phage suspensions are stable. The polypropylene surface of the Eppendorf-type and Falcon-type can accommodate from around 10⁸ PFU/ml to around 10¹⁰ PFU/ml from the suspension. The adsorption onto the container’s wall might result in complete scavenging of virions from the bulk. We developed two methods to overcome this issue. The addition of surfactant Tween20 and/or plasma treatment provides a remedy by modulating surface wettability and inhibiting virions' adsorption. Plastic containers are essential consumables in the daily use of many bio-laboratories. Thus, this is important not only for phage-related research (e.g., the use of phage therapies as an alternative for antibiotics) but also for data comparison and reproducibility in the field of biochemistry and virology.

Evaluation of the effectiveness of a new cryopreservation system based on a two-compartment vial for the cryopreservation of cell therapy products

BACKGROUND AIMS

Successful cell cryopreservation and banking remain a major challenge for the manufacture of cell therapy products, particularly in relation to providing a hermetic, sterile cryovial that ensures optimal viability and stability post-thaw while minimizing exposure to toxic cryoprotective agents, typically dimethyl sulfoxide (Me₂SO).

METHODS

In the present study, the authors evaluated the effectiveness and functionality of Limbo technology (Cellulis S.L., Santoña, Spain). This system provides a hermetic vial with two compartments (one for adding cells with the cryoprotective agent solution and the other for the diluent solution) and an automated defrosting device. Limbo technology (Cellulis S.L.) allows reduction of the final amount of Me₂SO, sidestepping washing and dilution steps and favoring standardization. The study was performed in several Good Manufacturing Practice laboratories manufacturing diverse cell therapy products (human mesenchymal stromal cells, hematopoietic progenitor cells, leukapheresis products, fibroblasts and induced pluripotent stem cells). Laboratories compared Limbo technology (Cellulis S.L.) with their standard cryopreservation procedure, analyzing cell recovery, viability, phenotype and functionality.

RESULTS

Limbo technology (Cellulis S.L.) maintained the viability and functionality of most of the cell products and preserved sterility while reducing the final concentration of Me₂SO.

CONCLUSIONS

Results showed that use of Limbo technology (Cellulis S.L.) offers an overall safe alternative for cell banking and direct infusion of cryopreserved cell products into patients.

pH-dependent sedimentation of DNA in the presence of divalent, but not monovalent, metal ions

Precipitation of DNA is performed frequently in molecular biology laboratories for the purpose of purification and concentration of samples and also for transfer of DNA into cells. Metal ions are used to facilitate these processes, though their precise functions are not well characterized. In the current study we have investigated the precipitation of double-stranded DNA by group 1 and group 2 metal ions. Double-stranded DNAs were not sedimented efficiently by metals alone, even at high concentrations. Increasing the pH to 11 or higher caused strong DNA precipitation in the presence of the divalent group 2 metals magnesium, calcium, strontium and barium, but not group 1 metals. Group 2 sedimentation profiles were distinctly different from that of the transition metal zinc, which caused precipitation at pH 8. Analysis of DNAs recovered from precipitates formed with calcium revealed that structural integrity was retained and that sedimentation efficiency was largely size-independent above 400 bp. Several tests supported a model whereby single-stranded DNA regions formed by denaturation at high pH became bound by the divalent metal cations. Neutralization of negative surface charges reduced the repulsive forces between molecules, leading to formation of insoluble aggregates that could be further stabilized by cation bridging (ionic crosslinking).

Elevating Chemistry Research with a Modern Electronics Toolkit

With the rapid development of high technology, chemical science is not as it used to be a century ago. Many chemists acquire and utilize skills that are well beyond the traditional definition of chemistry. The digital age has transformed chemistry laboratories. One aspect of this transformation is the progressing implementation of electronics and computer science in chemistry research. In the past decade, numerous chemistry-oriented studies have benefited from the implementation of electronic modules, including microcontroller boards (MCBs), single-board computers (SBCs), professional grade control and data acquisition systems, as well as field-programmable gate arrays (FPGAs). In particular, MCBs and SBCs provide good value for money. The application areas for electronic modules in chemistry research include construction of simple detection systems based on spectrophotometry and spectrofluorometry principles, customizing laboratory devices for automation of common laboratory practices, control of reaction systems (batch- and flow-based), extraction systems, chromatographic and electrophoretic systems, microfluidic systems (classical and nonclassical), custom-built polymerase chain reaction devices, gas-phase analyte detection systems, chemical robots and drones, construction of FPGA-based imaging systems, and the Internet-of-Chemical-Things. The technology is easy to handle, and many chemists have managed to train themselves in its implementation. The only major obstacle in its implementation is probably one's imagination.

Phenotypic Screening in C. elegans as a Tool for the Discovery of New Geroprotective Drugs

Population aging is one of the largest challenges of the 21st century. As more people live to advanced ages, the prevalence of age-related diseases and disabilities will increase placing an ever larger burden on our healthcare system. A potential solution to this conundrum is to develop treatments that prevent, delay or reduce the severity of age-related diseases by decreasing the rate of the aging process. This ambition has been accomplished in model organisms through dietary, genetic and pharmacological interventions. The pharmacological approaches hold the greatest opportunity for successful translation to the clinic. The discovery of such pharmacological interventions in aging requires high-throughput screening strategies. However, the majority of screens performed for geroprotective drugs in C. elegans so far are rather low throughput. Therefore, the development of high-throughput screening strategies is of utmost importance.

Mixed Ligand Shell Formation upon Catechol Ligand Adsorption on Hydrophobic TiO2 Nanoparticles

Modifying the surfaces of metal oxide nanoparticles (NPs) with monolayers of ligands provides a simple and direct method to generate multifunctional coatings by altering their surface properties. This works best if the composition of the monolayers can be controlled. Mussel-inspired, noninnocent catecholates stand out from other ligands like carboxylates and amines because they are redox-active and allow for highly efficient surface binding and enhanced electron transfer to the surface. However, a comprehensive understanding of their surface chemistry, including surface coverage and displacement of the native ligand, is still lacking. Here, we unravel the displacement of oleate (OA) ligands on hydrophobic, OA-stabilized TiO₂ NPs by catecholate ligands using a combination of one- and two-dimensional nuclear magnetic resonance (NMR) spectroscopy techniques. Conclusive pictures of the ligand shells before and after surface modification with catecholate were obtained by ¹H and ¹³C NMR spectroscopy (the ¹³C chemical shift being more sensitive and with a broader range). The data could be explained using a Langmuir-type approach. Gradual formation of a mixed ligand shell was observed, and the surface processes of catecholate adsorption and OA desorption were quantified. Contrary to the prevailing view, catecholate displaces only a minor fraction (∼20%) of the native OA ligand shell. At the same time, the total ligand density more than doubled from 2.3 nm^-2 at native oleate coverage to 4.8 nm^-2 at maximum catecholate loading. We conclude that the catecholate ligand adsorbs preferably to unoccupied Ti surface sites rather than replacing native OA ligands. This unexpected behavior, reminiscent of the Vroman effect for protein corona formation, appears to be a fundamental feature in the widely used surface modification of hydrophobic metal oxide NPs with catecholate ligands. Moreover, our findings show that ligand displacement on OA-capped TiO₂ NPs is not suited for a full ligand shell refunctionalization because it produces only mixed ligand shells. Therefore, our results contribute to a better understanding and performance of photocatalytic applications based on catecholate ligand-sensitized TiO₂ NPs.

Quantitative and Digital Droplet-Based AAV Genome Titration

The adeno-associated viral vector (AAV) platform has developed into a primary modality for efficient in vivo, and in more limited settings, in vitro or ex vivo gene transfer. Its applications range from a tool for experimental purposes to preclinical and clinical gene therapy. The ability to accurately and reproducibly quantify vector concentration is critical for any of these applications. While several quantification assays are available, here we outline a detailed protocol for the quantification of DNase-I protected vector genomes reliant on the polymerase chain reaction (PCR) as a measure of the active component of the vector, namely its transgene cargo. With the emergence of droplet digital PCR (ddPCR), we provide side-by-side protocols for traditional TaqMan™ real-time, quantitative PCR (qPCR) and ddPCR, as well as comparative data generated with both methods. Lastly, we discuss the importance of the use of surfactant (here, Pluronic^® F-68) in the execution of the assay to limit DNA and AAV adherence to various carriers during the titration, particularly at low concentrations. We believe these protocols can lead to reduced variability and increased comparability between AAV studies.

Laboratory plasticware - Use at your own risk: Suitability of microcentrifuge tubes for spores' analysis of Clostridium difficile

Clostridium difficile is a Gram-positive spore forming rod-shaped bacterium which causes mild to severe diarrhea. Spores play a key role in transmission of C. difficile in hospital environment. To investigate ability of spores to stay on fomites and to assess levels of contamination it is essential to prevent loss of spores collected for the analysis. Working with C. difficile spores we noticed a significant loss after vortexing of spore suspensions and investigated if it can be prevented by using a specific brand or type of microcentrifuge tubes. 7 types of microcentrifuge tubes from 3 manufacturers were tested. Spores of three types of C. difficile, NAP1/027, NAP4/014 and NAP7/078 (clinical isolates) were used. C. difficile was grown on Brucella Supplemented Agar for 9 days, spores were collected, washed and density of 3 suspensions was normalized to optical density (OD) 550 0.1 or 0.05. These suspensions (OD 0.1) were used in serial dilutions with 3 experimental conditions - pipetting, vortexing or vortexing in 3% albumin solution and in vortexing experiment when 150 μl were vortexed for 1 min at 1500 rpm per tube and loss of spores was measured by a decrease in dipicolinic acid (DPA) concentration measured by time-delayed terbium fluorescence. Inner surface of the tubes was visualized with microscopy to observe adhered spores. In serial dilution experiment, initial concentration of spores would be underestimated by up to 18X in case of vortexing for NAP1 strain and 9X for NAP4 strain. Presence of 3% albumin significantly decreases this effect but does not eliminate it completely. Comparison of 7 types of tubes shows that a single vortexing for 1 min of diluted spore suspension at concentrations of 1.8 × 10⁷ spores per ml leads to a loss of up to 90% of spores in some tubes. Degree of spores' adhesion varied between brands and types of tubes and between tubes of the same type. In some brands there was a significant variability in adhesion between tubes from the same batch. Microscopy after vortexing shows a film of spores attached to the tube's wall. Adherence could be affected by the type of plastic, additives (plasticizers) used in manufacturing and quality of moulds (e.g."diamond polished"). To identify the most appropriate type of tubes for the experiment it is essential to test it beforehand as not every brand is suitable for this purpose. Using tubes with a high degree of adherence could significantly affect measurement of spores' concentration in serial dilutions, e.g. when quantifying spores production by a specific strain or when limits of detection are measured. Also, sensitivity of commercial tests for detection of C. difficile in clinical specimens can be decreased if an unsuitable type of plastic containers and tubes is used.

Factors affecting the association of single- and double-stranded RNAs with montmorillonite nanoclays

Montmorillonite (MMT) nanoclays exist as single and stacked sheet-like structures with large surface areas that can form stable associations with many naturally occurring biomolecules, including nucleic acids. They have been utilized successfully as vehicles for delivery of both drugs and genes into cells. Most previous studies have focused on interactions of MMT with DNA. In the current study, we have investigated the binding of small RNAs similar to those used for RNA interference (RNAi) therapy to two major forms of the clay, Na-MMT and Ca-MMT. Association of both forms of MMT with several double-stranded RNAs (dsRNAs), including 25mers, 54mers and cloverleaf-shaped transfer RNAs, was weak and increased only slightly after addition of Mg2+ ions to the binding reactions. By contrast, ssRNA 25mers and 54mers bound poorly to Na-MMT but interacted strongly with Ca-MMT. The weak binding of ssRNAs to Na-MMT could be strongly enhanced by addition of Mg2+ ions. The strength of MMT-ssRNA interactions was also examined using inorganic anion competition and displacement assays, as well as electrophoretic mobility shift assays (EMSAs). The aggregate results point to a cation-bridging mechanism for binding of ssRNAs, but not dsRNAs, in the presence of divalent metal cations.

Characterization of a cyclic olefin polymer microcentrifuge tube

Here, we describe the properties of a prototype microcentrifuge tube made from the plastic cyclic olefin polymer (COP). This material has been used in the manufacture of primary containers including syringes and vials for the storage, shipment, and delivery of biotherapeutics, vaccines, and cell therapy products. Its low level of extractable substances and metals along with its glass-like clarity make COP an attractive material for the fabrication of microcentrifuge tubes and other consumable laboratory plasticware where contamination is an important consideration, such as in the storage and analysis of labile proteins, nucleic acids, and metabolites. We compare the performance of microcentrifuge tubes made of COP with that of several brands made of polypropylene (PP), the plastic most widely used in the manufacture of microcentrifuge tubes. Our results show COP microcentrifuge tubes perform as well as tubes made of PP, with reduced levels of compounds capable of leaching into solvents typically used in the laboratory.

In plastico: laboratory material newness affects growth and reproduction of Daphnia magna reared in 50-ml polypropylene tubes

Plastic laboratory materials are found to affect vital parameters of the waterflea Daphnia magna. The main responsible factor is defined as “newness” of the materials. Juvenile D. magna were raised individually in; a) new laboratory-standard 50 ml polypropylene tubes, and; b) identical tubes which had been washed and aerated for several weeks. Newness had significant effects on growth and fecundity of D. magna. New tubes caused delayed maturation, reduced reproduction and reduced growth when compared to washed and re-used tubes of the same commercial brand. The findings indicate that newness of tubes has inhibiting or toxic effects on D. magna. Often laboratory plastics are intended for single-use due to sterility demands. Newness might be an important confounding factor in research results and should not be disregarded. Disposable plastic utensils may come with a seemingly ignored cost and induce adverse effects in biological test-organisms and systems. The presented findings accentuate continued need for general awareness concerning confounding factors stemming from material laboratory environment. Based on the present findings the authors suggest that plastics intended for use in sensitive research may need to be washed and aerated prior to use.

DNA Source Selection for Downstream Applications Based on DNA Quality Indicators Analysis

High-quality human DNA samples and associated information of individuals are necessary for biomedical research. Biobanks act as a support infrastructure for the scientific community by providing a large number of high-quality biological samples for specific downstream applications. For this purpose, biobank methods for sample preparation must ensure the usefulness and long-term functionality of the products obtained. Quality indicators are the tool to measure these parameters, the purity and integrity determination being those specifically used for DNA. This study analyzes the quality indicators in DNA samples derived from 118 frozen human tissues in optimal cutting temperature (OCT) reactive, 68 formalin-fixed paraffin-embedded (FFPE) tissues, 119 frozen blood samples, and 26 saliva samples. The results obtained for DNA quality are discussed in association with the usefulness for downstream applications and availability of the DNA source in the target study. In brief, if any material is valid, blood is the most approachable option of prospective collection of samples providing high-quality DNA. However, if diseased tissue is a requisite or samples are available, the recommended source of DNA would be frozen tissue. These conclusions will determine the best source of DNA, according to the planned downstream application. Furthermore our results support the conclusion that a complete procedure of DNA quantification and qualification is necessary to guarantee the appropriate management of the samples, avoiding low confidence results, high costs, and a waste of samples.

Impact of size, secondary structure, and counterions on the binding of small ribonucleic acids to layered double hydroxide nanoparticles

Use of ribonucleic acid (RNA) interference to regulate protein expression has become an important research topic and gene therapy tool, and therefore, finding suitable vehicles for delivery of small RNAs into cells is of crucial importance. Layered double metal hydroxides such as hydrotalcite (HT) have shown great promise as nonviral vectors for transport of deoxyribose nucleic acid (DNA), proteins, and drugs into cells, but the adsorption of RNAs to these materials has been little explored. In this study, the binding of small RNAs with different lengths and levels of secondary structure to HT nanoparticles has been analyzed and compared to results obtained with small DNAs in concurrent experiments. Initial experiments established the spectrophotometric properties of HT in aqueous solutions and determined that HT particles could be readily sedimented with near 100% efficiencies. Use of RNA+HT cosedimentation experiments as well as electrophoretic mobility shift assays demonstrated strong adsorption of RNA 25mers to HT, with twofold greater binding of single-stranded RNAs relative to double-stranded molecules. Strong affinities were also observed with ssRNA and dsRNA 54mers and with more complex transfer RNA molecules. Competition binding and RNA displacement experiments indicated that RNA-HT associations were strong and were only modestly affected by the presence of high concentrations of inorganic anions.

Artefacts in 1H NMR-based metabolomic studies on cell cultures

OBJECT

Metabolomic studies on cultured cells involve assays of cell extracts and culture medium, both of which are often performed by (1)H NMR. Cell culture is nowadays performed in plastic dishes or flasks, and the extraction of metabolites from the cells is typically performed with perchloric acid, methanol-chloroform, or acetonitrile, ideally while the cells are still adherent to the culture dish. We conducted this investigation to identify contaminants from cell culture plasticware in metabolomic studies.

MATERIALS AND METHODS

Human diploid fibroblasts (IMR90) (n = 6), HeLa cells (n = 6), and transformed astrocytes with HIF-1 knockout (Astro-KO) (n = 6) were cultured. Cells were seeded in 100 mm Petri dishes with 10 ml complete growth medium (Dulbecco's minimum essential medium) containing 10 % foetal bovine serum (FBS). Cell cultures were incubated at 37 °C in 5 % CO2 for approximately 3 days. Metabolites were extracted by use of a perchloric acid procedure. (1)H NMR spectroscopy was used for metabolite analysis. "Null sample" (i.e. cell-free) experiments were performed by either rinsing dishes with medium or incubating the medium in Petri dishes from five different manufacturers for 72 h and then by performing a dummy "extraction" of each Petri dish by the perchloric acid, methanol-chloroform, or acetonitrile procedures. Principal components analysis was used for classification of samples and to determine the contaminants arising from plasticware.

RESULTS

We found that even brief rinsing of cell culture plasticware with culture medium elutes artefactual chemicals, the (1)H NMR signals of which could confound assays of acetate, succinate, and glycolate. Incubation of culture medium in cell-culture dishes for 72 h (as in a typical cell-culture experiment) followed by perchloric extraction in the dishes enhanced elution of the artefacts. These artefacts were present, but somewhat less pronounced, in the (1)H NMR spectra of null samples extracted with methanol and acetonitrile. Ethanol, lactate, alanine, fructose, and fumarate signals that appear in the (1)H NMR spectrum of the unused (pure) medium originate from FBS.

CONCLUSIONS

Plastic Petri dishes from five different manufacturers gave rise to essentially identical artefactual peaks. Use of a pH indicator to assist neutralisation introduced still more artefactual signals in the aromatic region, as well as methanol and ethanol signals. Methanol and acetonitrile extracts also contained artefacts arising from the plasticware, although the amounts were less than in the perchloric acid extracts. Finally, we provide suggestions for minimizing these artefacts. The best practice would be to run a "null" extraction with every batch of cellular metabolomics experiments to test for contamination and to provide a "background" spectrum.

Chemicals eluting from disposable plastic syringes and syringe filters alter neurite growth, axogenesis and the microtubule cytoskeleton in cultured hippocampal neurons

Cultures of dissociated hippocampal neurons are often used to study neuronal cell biology. We report that the development of these neurons is strongly affected by chemicals leaching from commonly used disposable medical-grade syringes and syringe filters. Contamination of culture medium by bioactive substance(s) from syringes and filters occurred with multiple manufacturing lots and filter types under normal use conditions and resulted in changes to neurite growth, axon formation and the neuronal microtubule cytoskeleton. The effects on neuronal morphology were concentration dependent and significant effects were detected even after substantial dilution of the contaminated medium. Gas chromatography-mass spectrometry analyses revealed many chemicals eluting from the syringes and filters. Three of these chemicals (stearic acid, palmitic acid and 1,2-ethanediol monoacetate) were tested but showed no effects on neurite growth. Similar changes in neuronal morphology were seen with high concentrations of bisphenol A and dibutyl phthalate, two hormonally active plasticisers. Although no such compounds were detected by gas chromatography–mass spectrometry, unknown plasticisers in leachates may affect neurites. This is the first study to show that leachates from laboratory consumables can alter the growth of cultured hippocampal neurons. We highlight important considerations to ensure leachate contamination does not compromise cell biology experiments.

Fungal community analysis by high-throughput sequencing of amplified markers--a user's guide

Novel high-throughput sequencing methods outperform earlier approaches in terms of resolution and magnitude. They enable identification and relative quantification of community members and offer new insights into fungal community ecology. These methods are currently taking over as the primary tool to assess fungal communities of plant-associated endophytes, pathogens, and mycorrhizal symbionts, as well as free-living saprotrophs. Taking advantage of the collective experience of six research groups, we here review the different stages involved in fungal community analysis, from field sampling via laboratory procedures to bioinformatics and data interpretation. We discuss potential pitfalls, alternatives, and solutions. Highlighted topics are challenges involved in: obtaining representative DNA/RNA samples and replicates that encompass the targeted variation in community composition, selection of marker regions and primers, options for amplification and multiplexing, handling of sequencing errors, and taxonomic identification. Without awareness of methodological biases, limitations of markers, and bioinformatics challenges, large-scale sequencing projects risk yielding artificial results and misleading conclusions.

Charge density and particle size effects on oligonucleotide and plasmid DNA binding to nanosized hydrotalcite

Hydrotalcite (HT) and other layered double metal hydroxides are of great interest as gene delivery and timed release drug delivery systems and as enteric vehicles for biologically active molecules that are sensitive to gastric fluids. HT is a naturally occurring double metal hydroxide that can be synthesized as a nanomaterial consisting of a brucite structure with isomorphous substitution of aluminum ions. These positively charged nanoparticles exhibit plate-like morphology with very high aspect ratios. Biomolecules such as nucleic acids and proteins form strong associations with HT because they can associate with the positively charged layers. The binding of nucleic acids with HT and other nanomaterials is currently being investigated for potential use in gene therapy; however, the binding of specific nucleic acid forms, such as single- and double-stranded DNA, has been little explored. In addition, the effects of charge density and particle size on DNA adsorption has not been studied. In this paper, the binding of different forms of DNA to a series of HTs prepared at different temperatures and with different anion exchange capacities has been investigated. Experiments demonstrated that HTs synthesized at higher temperatures associate with both single- and double-stranded oligomers and circular plasmid DNA more tightly than HTs synthesized at room temperature, likely due to the hydrothermal conditions promoting larger particle sizes. HT with an anion exchange capacity of 300 meq/100 g demonstrated the highest binding of DNA, likely due to the closer match of charge densities between the HT and DNA. The details of the interaction of various forms of DNA with HT as a function of charge density, particle size, and concentration are discussed.

On the disruption of biochemical and biological assays by chemicals leaching from disposable laboratory plasticware

Plastic consumables, used universally in bioscience laboratories, are presumed inert with respect to bioassay outcomes. However, it is clear that many pipette tips, microfuge tubes, and other plastic disposables leach bioactive compounds into assay solutions, profoundly affecting data and experimental interpretation. In this paper we discuss the nature and sources of leachates and review several examples of compromised bioassay data that speak to the probable widespread nature of this largely unrecognised source of error. Strategies for minimizing leachate interferences are discussed.

Mechanism of polyubiquitin chain recognition by the human ubiquitin conjugating enzyme Ube2g2

Ube2g2 is a human ubiquitin conjugating (E2) enzyme involved in the endoplasmic reticulum-associated degradation pathway, which is responsible for the identification and degradation of unfolded and misfolded proteins in the endoplasmic reticulum compartment. The Ube2g2-specific role is the assembly of Lys-48-linked polyubiquitin chains, which constitutes a signal for proteasomal degradation when attached to a substrate protein. NMR chemical shift perturbation and paramagnetic relaxation enhancement approaches were employed to characterize the binding interaction between Ube2g2 and ubiquitin, Lys-48-linked diubiquitin, and Lys-63-linked diubiquitin. Results demonstrate that ubiquitin binds to Ube2g2 with an affinity of 90 μM in two different orientations that are rotated by 180° in models generated by the RosettaDock modeling suite. The binding of Ube2g2 to Lys-48- and Lys-63-linked diubiquitin is primarily driven by interactions with individual ubiquitin subunits, with a clear preference for the subunit containing the free Lys-48 or Lys-63 side chain (i.e. the distal subunit). This preference is particularly striking in the case of Lys-48-linked diubiquitin, which exhibits an ∼3-fold difference in affinities between the two ubiquitin subunits. This difference can be attributed to the partial steric occlusion of the subunit whose Lys-48 side chain is involved in the isopeptide linkage. As such, these results suggest that Lys-48-linked polyubiquitin chains may be designed to bind certain proteins like Ube2g2 such that the terminal ubiquitin subunit carrying the reactive Lys-48 side chain can be positioned properly for chain elongation regardless of chain length.