Review of Chloride Ion Detection Technology in Water

High-sensitivity and energy-efficient chloride ion sensors based on flexible printed carbon nanotube thin-film transistors for wearable electronics

The advent of flexible single-walled carbon nanotube thin-film transistors (SWCNT-TFTs) has transformed electronics, providing significant benefits like low operating voltage, reduced power consumption, cost-effectiveness, and improved signal amplification. This study focuses on leveraging these attributes to develop a novel flexible high-sensitivity and energy-efficient chloride ion sensors based on printed flexible SWCNT-TFTs utilizing polymers-sorted semiconducting SWCNTs (sc-SWCNTs) as the active layers and ion liquids-poly(4-vinylphenol as dielectric layers along with the evaporated deposition of aluminum electrodes and printed silver electrodes as the gate and source-drain electrodes, respectively. The sensors exhibit several operational advantages, including low voltage requirements (≤1 V), rapid response speed (5.32 s), significant signal amplification (Up to 702.6 %), low power consumption (0.31 μJ at 1 mmol chloride ion), good repeatability, high sensitivity for both low and high concentrations of chloride ion (up to 100 mmol/L) and excellent mechanical flexibility (No obvious changes after bending for 10,000 times with a 5 mm radius). The detection mechanism of chloride ions was analyzed using X-ray Photoelectron Spectroscopy (XPS). It was found that chloride ions react with silver nanoparticles (AgNPs) to form silver chloride (AgCl) on printed electrodes, impeding carrier transport and reducing the currents in SWCNT TFTs. Importantly, our sensors' compatibility with smart devices allows for real-time monitoring of chloride ion levels in human sweat, offering significant potential for daily health monitoring.

Voltammetric Sensing of Chloride Based on a Redox-Active Complex: A Terpyridine-Co(II)-Dipyrromethene Functionalized Anion Receptor Deposited on a Gold Electrode

A redox-active complex containing Co(II) connected to a terpyridine (TPY) and dipyrromethene functionalized anion receptor (DPM-AR) was created on a gold electrode surface. This host-guest supramolecular system based on a redox-active layer was used for voltammetric detection of chloride anions in aqueous solutions. The sensing mechanism was based on the changes in the redox activity of the complex observed upon binding of the anion to the receptor. The electron transfer coefficient (α) and electron transfer rate constant (k0) for the modified gold electrodes were calculated based on Cyclic Voltammetry (CV) experiments results. On the other hand, the sensing abilities were examined using Square Wave Voltammetry (SWV). More importantly, the anion receptor was selective to chloride, resulting in the highest change in Co(II) current intensity and allowing to distinguish chloride, sulfate and bromide. The proposed system displayed the highest sensitivity to Cl- with a limit of detection of 0.50 fM. The order of selectivity was: Cl- > SO42- > Br-, which was confirmed by the binding constants (K) and reaction coupling efficiencies (RCE).

Influence of Inorganic Anions on the Chemical Stability of Molybdenum Disulfide Nanosheets in the Aqueous Environment

Chemical stability is closely associated with the transformations and bioavailabilities of engineered nanomaterials and is a key factor that governs broader and long-term application. With the growing utilization of molybdenum disulfide (MoS2) nanosheets in water treatment and purification processes, it is crucial to evaluate the stability of MoS2 nanosheets in aquatic environments. Nonetheless, the effects of anionic species on MoS2 remain largely unexplored. Herein, the stability of chemically exfoliated MoS2 nanosheets (ceMoS2) was assessed in the presence of inorganic anions. The results showed that the chemical stability of ceMoS2 was regulated by the nucleophilicities and the resultant charging effects of the anions in aquatic systems. The anions promote the dissolution of ceMoS2 by triggering a shift in the chemical potential of the ceMoS2 surface as a function of the anion nucleophilicity (i.e., charging effect). Fast charging with HCO3- and HPO42-/H2PO4- was validated by a phase transition from 1T to 2H and the emergence of MoV, and it promoted oxidative dissolution of the ceMoS2. Additionally, under sunlight, ceMoS2 dissolution was accelerated by NO3-. These findings provide insight into the ion-induced fate of ceMoS2 and the durability and risks of MoS2 nanosheets in environmental applications.

Selective leaching process for efficient and rapid recycling of spent lithium iron phosphate batteries

With the continuous development of new energy vehicles, the number of decommissioned lithium iron phosphate (LiFePO4) batteries has been constantly increasing. Therefore, it is necessary to recover metal from spent LiFePO4 batteries due to the high potential for environmental protection and high resource value. In this study, sodium persulfate (Na2S2O8) was selected as the oxidant to regulate and control the oxidation state and proton activity of the leaching solution through its high oxidizing ability. Selective recovery of lithium from LiFePO4 batteries was achieved by oxidizing LiFePO4 to iron phosphate (FePO4) during the leaching process. This paper reports an extensive investigation of the effects of various factors, including the acid concentration, initial volume fraction of the oxidant, reaction temperature, solid-liquid ratio, and reaction time, on lithium leaching. Li+ reached a high leaching rate of 93.3% within 5 minutes even at a low concentration of sulphuric acid (H2SO4), and high-purity lithium carbonate (Li2CO3) was obtained through impurity removal and precipitation reactions. In addition, the leaching mechanism was analysed by both X-ray diffraction and X-ray photoelectron spectroscopy characterization. The results show that the obtained high lithium-ion (Li+) leaching efficiency and fast Li+ leaching time can be ascribed to the superior oxidizing properties of Na2S2O8 and the stability of the crystal structure of LiFePO4 during the oxidative leaching process. The adopted method has significant advantages in terms of safety, efficiency and environmental protection, which are conducive to the sustainable development of lithium batteries.

Positive and negative effects of recirculating aquaculture water advanced oxidation: O3 and O3/UV treatments improved water quality but increased antibiotic resistance genes

Recirculating aquaculture systems (RASs) can be efficiently used for aquaculture, and oxidation treatment is commonly used to improve water quality. However, the effects of oxidation treatments on aquaculture water safety and fish yield in RASs are poorly understood. In this study, we tested the effects of O₃ and O₃/UV treatments on aquaculture water quality and safety during culture of crucian carp. O₃ and O₃/UV treatments reduced the dissolved organic carbon (DOC) concentration by ∼40% and destroyed the refractory organic lignin-like features. There was enrichment of ammonia oxidizing (Nitrospira, Nitrosomonas, and Nitrosospira) and denitrifying (Pelomonas, Methyloversatilis, and Sphingomonas) bacteria, and N-cycling functional genes were enriched by 23% and 48%, respectively, after O₃ and O₃/UV treatments. Treatment with O₃ and O₃/UV reduced NH₄⁺-N and NO₂^--N in RASs. O₃/UV treatment increased fish length and weight as well as probiotics in fish intestine. However, high saturated intermediates and tannin-like features induced antibiotic resistance genes (ARGs) in O₃ and O₃/UV treatments, by 52% and ∼28%, respectively, and also enhanced horizontal transfer of ARGs. Overall, the application of O₃/UV achieved better effects. However, understanding the potential biological risks posed by ARGs in RASs and determining the most efficient water treatment strategies to mitigate these risks should be goals of future work.

Removal of high concentration of chloride ions by electrocoagulation using aluminium electrode

Wastewater containing a high concentration of chloride ions (Cl^- ions) generated in industrial production will corrode equipment and pipelines and cause environmental problems. At present, systematic research on Cl^- removal by electrocoagulation is scarce. To study the Cl^- removal mechanism, process parameters (current density and plate spacing), and the influence of coexisting ions on the removal of Cl^- in electrocoagulation, we use aluminum (Al) as the sacrificial anode, combined with physical characterization and density functional theory (DFT) to study Cl^- removal by electrocoagulation. The result showed that the use of electrocoagulation technology to remove Cl^- can reduce the concentration of Cl^- in an aqueous solution below 250 ppm, meeting the Cl^- emission standard. The mechanism of Cl^- removal is mainly co-precipitation and electrostatic adsorption by forming chlorine-containing metal hydroxyl complexes. The current density and plate spacing affect the Cl^- removal effect and operation cost. As a coexisting cation, magnesium ion (Mg²⁺) promotes the removal of Cl^-, while calcium ion (Ca²⁺) inhibits it. Fluoride ion (F^-), sulfate (SO₄^2-), and nitrate (NO₃^-) as coexisting anions affect the removal of Cl^- ions through competitive reaction. This work provides a theoretical basis for the industrialization of Cl^- removal by electrocoagulation.