The Era of Nanomaterials: A Safe Solution or a Risk for Marine Environmental Pollution?

Prevention is better than a cure: A 'zero residual nanoadsorbent toxicity' downstream from its effluent exit point

Here, we offer thoughts concerning a 'zero residual nanoadsorbent toxicity' environmental policy which we strongly advocate. Our discussions in support of this policy are based on the adage 'Prevention is better than cure'. Besides emphasizing the need for strict regulations (regional and international), research and development avenues are highlighted for the technology that can achieve 'zero tolerance' for residual nanoadsorbent levels escaping and building up in receiving ecosystems. We do not oppose nanoadsorbents. On the contrary, their water and wastewater purification potentials are well recognized. However, they should not be permitted to translocate downstream from the exit point of a final effluent.

Metal variability of the shrimp Palaemon elegans across coastal zones: anthropogenic and geological impacts

This study focused on 120 specimens of the shrimp Palaemon elegans collected in intertidal zones in eight selected areas. This study aimed to assess the suitability of P. elegans as a bioindicator of natural and anthropogenic marine pollution. Metal concentrations of aluminum (Al), cadmium (Cd), copper (Cu), iron (Fe), lead (Pb), and zinc (Zn) were measured in shrimp collected from various sites in the Canary Islands, including areas affected by volcanic activity, industrial activity, and control zones. The determination of metal concentrations was conducted using inductively coupled plasma optical emission spectrophotometry (ICP-OES). The results showed significant differences in metal concentrations across the studied sites, with the highest levels of Al, Cu, Fe, Pb, and Zn observed in areas impacted by the Tajogaite volcanic eruption and harbor activity. Sites near old landfills and sewage pipes also exhibited elevated levels of Cd, Cu, and Pb, indicating strong anthropogenic influence. Al was found in the highest concentration in Harbour, reaching 25.7 ± 6.2 mg/kg, while the lowest concentration was observed in Control Lp at 11.5 ± 0.69 mg/kg. Conversely, lower metal concentrations were detected in control zones and areas with high dinoflagellate presence, suggesting a potential role of bioremediation by marine phytoplankton. The ability of P. elegans to accumulate metals in its tissues, particularly in areas of high pollution, highlights its potential as a bioindicator species. This study underscores the importance of P. elegans in monitoring marine pollution and provides insights into the environmental impact of both natural and human-induced contamination on coastal ecosystems.

A scientometric analysis and recent advances of emerging chitosan-based biomaterials as potential catalyst for biodiesel production: A review

Chitosan is a widely available polymer with a reasonably high abundance, as well as a sustainable, biodegradable, and biocompatible material with different functional groups that are used in a wide range of operations. Chitosan is frequently employed in widespread applications such as environmental remediation, adsorption, catalysts, and drug formulation. The goal of this review is to discuss the potential applications of chitosan and its chemically modified solids as a catalyst in biodiesel production. The existing manuscripts are integrated based on the nature of materials used as chitosan and its modifications. A short overview of chitosan's structural characteristics, properties, and some ideal methods to be considered in catalysis activities are addressed. This article includes an analysis of a chitosan-based scientometric conducted between 1975 and 2023 using VOS viewer 1.6.19. To identify developments and technological advances in chitosan research, the significant scientometric features of yearly publication results, documents country network, co-authorship network, documents funding sponsor, documents institution network, and documents category in domain analysis were examined. This review covers a variety of organic transformations and their effects, including chitosan reactions against acids, bases, metals, metal oxides, organic compounds, lipases, and Knoevenagel condensation. The catalytic capabilities of chitosan and its modified structures for producing biodiesel through transesterification reactions are explored in depth.

Silver Nanoparticles Supported onto TEMPO-Oxidized Cellulose Nanofibers for Promoting Cd2+ Cation Adsorption

Nanocellulose constitutes a sustainable and biobased solution both as an efficient sorbent material for water treatment and as support for other inorganic nanomaterials with sorbent properties. Herein, we report the synthesis of a nanocomposite by deposition of in situ-generated silver nanoparticles (AgNPs) onto TEMPO-oxidized cellulose nanofibers (TOCNFs). Following an in-depth analytical investigation, we unveil for the first time the key role of AgNPs in enhancing the adsorption efficiency of TOCNF toward Cd2+ ions, chosen as model heavy metal contaminants. The obtained nanocomposite shows a value of Cd2+ sorption capacity at equilibrium from 150 mg L-1 ion aqueous solutions of ∼116 mg g-1 against the value of 78 mg g-1 measured for TOCNF alone. A combination of field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray (EDX), and X-ray photoelectron spectroscopy (XPS) analyses suggests that Cd2+ ions are mainly adsorbed in the neighborhood of AgNPs. However, XPS characterization allows us to conclude that the role of AgNPs relies on increasing the exposure of carboxylic groups with respect to the original TOCNF, suggesting that these groups are still responsible for absorption. In fact, X-ray absorption spectroscopy (XAS) analysis of the Cd-K edge excludes a direct interaction between Ag0 and Cd2+, supporting the XPS results and confirming the coordination of the latter with carboxyl groups.

Nanostructured cellulose sponge engineered for marine environmental remediation: Eco-safety assessment of its leachate on sea urchin reproduction (Part A)

Nanostructured cellulose sponges (CNS) have been developed as eco-friendly and sustainable engineered materials for marine environmental remediation. Despite their functionality, sensitivity, efficiency and specificity have been proved, CNS application is still limited since their environmental safety (eco-safety) has not been completely assessed. In this study, CNS were allowed to leach in natural seawater simulating the remediation process condition and the eco-safety of CNS leachate on sea urchin reproduction has been assessed by carrying out a multi-response integrated approach, combining standardized ecotoxicity tests, innovative bioassays and gamete quality assessment. Overall, the ecotoxicity data indicate that CNS leachate affects gamete quality, gamete fertilisation competence, and embryo development probably associated with the release of chemical additives used during the synthesis process. However, in the framework of the eco-design approach, consecutive leaching treatments and conditioning of CNS in seawater open the route for a new safety protocol successfully solving the ecotoxicity while maintaining CNS sorbent properties. A safe environmental application of the resulting conditioned CNS for seawater pollution remediation is envisaged.

Shipping can be achieved but cargo arrives with damage - titanium dioxide nanoparticles affect the DNA of Pacific oyster sperm

Titanium dioxide nanoparticles (TiO₂ NP) were reported to be reprotoxic in humans and fish. However, the effects of these NP on the reproduction of marine bivalves, namely oysters, remain unknown. Thus, a short-term (1 h) direct exposure of sperm of the Pacific oyster (Crassostrea gigas) to two TiO₂ NP concentrations (1 and 10 mg.L-1) was performed, and sperm motility, antioxidant responses, and DNA integrity were evaluated. Although no changes occurred in sperm motility and the activities of the antioxidants, the genetic damage indicator increased at both concentrations, demonstrating that TiO₂ NP affects the DNA integrity of oyster sperm. Although DNA transfer can happen, it does not fulfill its biological mission since the transferred DNA is not intact and may compromise the reproduction and recruitment of the oysters. This vulnerability of C. gigas sperm towards TiO₂ NP highlights the importance of studying the effects of NPs exposure to broadcast spawners.

Environmental safety of nanotechnologies: The eco-design of manufactured nanomaterials for environmental remediation

Nanosafety is paramount considering the risks associated with manufactured nanomaterials (MNMs) whose implications could outweigh their advantages for environmental applications. Although nanotechnology-based solutions to implement pollution control, remediation and prevention are incremental with clear benefits for public health and Earth' natural ecosystems, nanoremediation is having a setback due to the risks associated with the safety of MNMs for humans and the environment. MNMs are diverse, work differently and bionano-interactions occurring upon environmental exposure will guide their fate and hazardous outcomes. Here we propose a new ecologically-based design strategy (eco-design) having its roots in green nanoscience and LCA that will ground on an Ecological Risk Assessment approach, which introduces the evaluation of MNMs' ecotoxicity along with their performances and efficacies at the design stage. As such, the proposed eco-design strategy will allow recognition and design-out since the very beginning of material synthesis, those hazardous peculiar features that can be hazardous to living beings and the natural environment. A more ecologically sound eco-design strategy in which nanosafety is conceptually included in MNMs design will sustain safer nanotechnologies including those for the environment as remediation by leveraging any risks for humans and natural ecosystems.

Composites of Lignin-Based Biochar with BiOCl for Photocatalytic Water Treatment: RSM Studies for Process Optimization

Textile effluents pose a massive threat to the aquatic environment, so, sustainable approaches for environmentally friendly multifunctional remediation methods degradation are still a challenge. In this study, composites consisting of bismuth oxyhalide nanoparticles, specifically bismuth oxychloride (BiOCl) nanoplatelets, and lignin-based biochar were synthesized following a one-step hydrolysis synthesis. The simultaneous photocatalytic and adsorptive remediation efficiency of the Biochar-BiOCl composites were studied for the removal of a benchmark azo anionic dye, methyl orange dye (MO). The influence of various parameters (such as catalyst dosage, initial dye concentration, and pH) on the photo-assisted removal was carried out and optimized using the Box-Behnken Design of RSM. The physicochemical properties of the nanomaterials were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, thermogravimetric analysis, nitrogen sorption, and UV-Vis diffuse reflectance spectroscopy (DRS). The maximum dye removal was observed at a catalyst dosage of 1.39 g/L, an initial dye concentration of 41.8 mg/L, and a pH of 3.15. The experiment performed under optimized conditions resulted in 100% degradation of the MO after 60 min of light exposure. The incorporation of activated biochar had a positive impact on the photocatalytic performance of the BiOCl photocatalyst for removing the MO due to favorable changes in the surface morphology, optical absorption, and specific surface area and hence the dispersion of the photo-active nanoparticles leading to more photocatalytic active sites. This study is within the frames of the design and development of green-oriented nanomaterials of low cost for advanced (waste)water treatment applications.

Eco-Friendly Engineered Nanomaterials Coupled with Filtering Fine-Mesh Net as a Promising Tool to Remediate Contaminated Freshwater Sludges: An Ecotoxicity Investigation

The use of eco-friendly engineered nanomaterials represents a recent solution for an effective and safe treatment of contaminated dredging sludge. In this study, an eco-designed engineered material based on cross-linked nanocellulose (CNS) was applied for the first time to decontaminate a real matrix from heavy metals (namely Zn, Ni, Cu, and Fe) and other undesired elements (mainly Ba and As) in a lab-scale study, with the aim to design a safe solution for the remediation of contaminated matrices. Contaminated freshwater sludge was treated with CNS coupled with a filtering fine-mesh net, and the obtained waters were tested for acute and sublethal toxicity. In order to check the safety of the proposed treatment system, toxicity tests were conducted by exposing the bacterium Aliivibrio fischeri and the crustacean Heterocypris incongruens, while subtoxicity biomarkers such as lysosomal membrane stability, genetic, and chromosomal damage assessment were performed on the freshwater bivalve Dreissena polymorpha. Dredging sludge was found to be genotoxic, and such genotoxicity was mitigated by the combined use of CNS and a filtering fine-mesh net. Chemical analyses confirmed the results by highlighting the abetment of target contaminants, indicating the present model as a promising tool in freshwater sludge nanoremediation.

Occurrence and distribution of legacy and emerging pollutants including plastic debris in Antarctica: Sources, distribution and impact on marine biodiversity

Since the first explorers reached Antarctica, their activities have quickly impacted both land and sea and thus, together with the long-range transport, hazardous chemicals began to accumulate. It is commonly recognized that anthropogenic pollution in Antarctica can originate from either global or local sources. Heavy metals, organohalogenated compounds, hydrocarbons, and (more recently) plastic, have been found in Antarctic biota, soil sediments, seawater, air, snow and sea-ice. Studies in such remote areas are challenging and expensive, and the complexity of potential interactions occurring in such extreme climate conditions (i.e., low temperature) makes any accurate prediction on potential impacts difficult. The present review aims to summarize the current state of knowledge on occurrence and distribution of legacy and emerging pollutants in Antarctica, such as plastic, from either global or local sources. Future actions to monitor and mitigate any potential impact on Antarctic biodiversity are discussed.

Recent advances in nanotechnology for remediation of heavy metals

Heavy metal contamination of the environment has become an alarming environmental issue that has constituted serious threats to humans and the ecosystem. These metals have been identified as a priority class of pollutants due to their persistency in the environment and their potential to bioaccumulate in biological systems. Consequently, the remediation of heavy metals from various environmental matrices becomes a critical topic from the biological and environmental perspectives. To this end, various research interests have shifted to the need to put forward economically feasible and highly efficient approaches for mitigating these contaminants in the environment. Thus, numerous conventional approaches have reportedly been employed for the remediation of heavy metals, with each of the methods having its inherent limitations. More recently, studies have revealed that nanomaterials in their various forms show unique potential for the removal of various contaminants including heavy metals in comparison to their bulk counterparts making them a topic of importance to researchers in various fields. Also, various studies have documented specifically tailored nanomaterials that have been synthesized for the removal of heavy metals from various environmental matrices. This review provides up-to-date information on the application of nanotechnology for the remediation of heavy metals. It highlights various nanomaterials that have been employed for the remediation of heavy metals, current details on their methods of synthesis, factors affecting their adsorption processes, and the environmental and health impact of nanomaterials. Finally, it provides the challenges and future trends of nanomaterials for heavy metal removal.

Health and Environmental Effect of Advanced Materials and Fine Particles

With the recent development in material sciences, advanced materials have become terms widely used for new materials [...]

The Acute and Short-Term Inhalation of Carbon Nanofiber in Sprague-Dawley Rats

The inhalation toxicity of carbon nanofibers (CNFs) is not clearly known due to relatively few related studies reported. An acute inhalation study and short-term inhalation study (5 days) were therefore conducted using Sprague-Dawley rats. In the acute inhalation study, the rats were grouped and exposed to a fresh air control or to low (0.238 ± 0.197), moderate (1.935 ± 0.159), or high (24.696 ± 6.336 mg/m³) CNF concentrations for 6 h and thereafter sacrificed at 14 days. For the short-term inhalation study, the rats were grouped and exposed to a fresh air control or low (0.593 ± 0.019), moderate (2.487 ± 0.213), or high (10.345 ± 0.541 mg/m³) CNF concentrations for 6 h/day for 5 days and sacrificed at 1, 3, and 21 days post-exposure. No mortality was observed in the acute inhalation study. Thus, the CNF LC₅₀ was higher than 25 mg/m³. No significant body or organ weight changes were noted during the 5 days short-term inhalation study or during the post-exposure period. No significant effects of toxicological importance were observed in the hematological, blood biochemical, and coagulation tests. In addition, the bronchoalveolar lavage (BAL) fluid cell differential counts and BAL inflammatory markers showed no CNF-exposure-relevant changes. The histopathological examination also found no CNF-exposure-relevant histopathological lesions. Thus, neither acute nor 5 days inhalation exposure to CNFs induced any noticeable toxicological responses.

Fungal bioassays for environmental monitoring

Environmental pollutants are today a major concern and an intensely discussed topic on the global agenda for sustainable development. They include a wide range of organic compounds, such as pharmaceutical waste, pesticides, plastics, and volatile organic compounds that can be found in air, soil, water bodies, sewage, and industrial wastewater. In addition to impacting fauna, flora, and fungi, skin absorption, inhalation, and ingestion of some pollutants can also negatively affect human health. Fungi play a crucial role in the decomposition and cycle of natural and synthetic substances. They exhibit a variety of growth, metabolic, morphological, and reproductive strategies and can be found in association with animals, plants, algae, and cyanobacteria. There are fungal strains that occur naturally in soil, sediment, and water that have inherent abilities to survive with contaminants, making the organism important for bioassay applications. In this context, we reviewed the applications of fungal-based bioassays as a versatile tool for environmental monitoring.

Critical review of the characteristics, interactions, and toxicity of micro/nanomaterials pollutants in aquatic environments

A wide range of contaminants of emerging concern such as micro/nanoplastics (MPs/PNPs) and metal-nanoparticles (Me-NPs) from anthropogenic activities have been identified in aquatic environments. The hazardous effects of these micro/nanomaterials as pollutants in organisms and the lack of knowledge about their behavior in aquatic environments have generated growing concern in the scientific community. The nanomaterials have a colloidal-type behavior due to their size range but with differences in their physicochemical properties. This review comprises the behavior of micro/nanomaterials pollutants and the physicochemical interactions between MPs/PNPs and Me-NPs in aquatic environments, and their potential toxicological effects in organisms. Moreover, this article describes the potential use of Me-NPs to remove MPs/PNPs present in the water column due to their photocatalytic and magnetic properties. It also discusses the challenge to determine harmful effects of micro/nanomaterials pollutants in organisms and provides future research directions to improve integrated management strategies to mitigate their environmental impact.

Eco-Interactions of Engineered Nanomaterials in the Marine Environment: Towards an Eco-Design Framework

Marine nano-ecotoxicology has emerged with the purpose to assess the environmental risks associated with engineered nanomaterials (ENMs) among contaminants of emerging concerns entering the marine environment. ENMs’ massive production and integration in everyday life applications, associated with their peculiar physical chemical features, including high biological reactivity, have imposed a pressing need to shed light on risk for humans and the environment. Environmental safety assessment, known as ecosafety, has thus become mandatory with the perspective to develop a more holistic exposure scenario and understand biological effects. Here, we review the current knowledge on behavior and impact of ENMs which end up in the marine environment. A focus on titanium dioxide (n-TiO₂) and silver nanoparticles (AgNPs), among metal-based ENMs massively used in commercial products, and polymeric NPs as polystyrene (PS), largely adopted as proxy for nanoplastics, is made. ENMs eco-interactions with chemical molecules including (bio)natural ones and anthropogenic pollutants, forming eco- and bio-coronas and link with their uptake and toxicity in marine organisms are discussed. An ecologically based design strategy (eco-design) is proposed to support the development of new ENMs, including those for environmental applications (e.g., nanoremediation), by balancing their effectiveness with no associated risk for marine organisms and humans.