Cellulose-Silver Composites Materials: Preparation and Applications

Silver-nanoparticle-modified nanocellulose synthesized by pyroligneous acid: cytotoxicity towards HaCat cells

In the present study, pyroligneous acid, also known as wood vinegar, has been employed as reducing and stabilizing agent in the synthesis of silver nanoparticles (AgNPs) anchored on nanocellulose (NC). The idea is to confer the latter bactericidal properties for its typical uses such as in cosmetics and food-packing. It has been demonstrated that AgNPs can be directly produced onto NC in one-pot fashion while dramatically enhancing the kinetics of AgNPs synthesis (2 h for reaction completion) in comparison to the NC-less counterpart (10 days for reaction completion). Furthermore, NC allowed for a narrower size distribution of AgNPs. NC-supported and non-supported AgNPs had sizes of 5.1 ± 1.6 nm and 16.7 ± 4.62 nm, respectively. Immortalized human keratinocytes (HaCat) cells were then employed as model to evaluate the cytotoxicity of the AgNPs-NC compound. The latter was found not to impact cell proliferation at any formulation, while decreasing the viability by only 6.8% after 72 h. This study contributes to the development of more environmentally benign routes to produce nanomaterials and to the understanding of their impact on cells.

The Nanoscale Ordering of Cellulose in a Hierarchically Structured Hybrid Material Revealed Using Scanning Electron Diffraction

Cellulose, being a renewable and abundant biopolymer, has garnered significant attention for its unique properties and potential applications in hybrid materials. Understanding the hierarchical arrangement of cellulose nanofibers is crucial for developing cellulose-based materials with enhanced mechanical properties. In this study, the use of Scanning Electron Diffraction (SED) is presented to map the nanoscale orientation of cellulose fibers in a bio-composite material with a preserved wood cell structure. The SED data provides detailed insights into the ordering of cellulose with an extraordinary resolution of ≈15 nm. It enables a quantitative analysis of the fiber orientation over regions as large as entire cells. A highly organized arrangement of cellulose fibers within the secondary cell wall is observed, with a gradient of orientations toward the outer part of the wall. The in-plane fiber rotation is quantified, revealing a uniform orientation close to the middle lamella. Transversely sectioned material exhibits similar trends, suggesting a layered cell wall structure. Based on the SED data, a 3D model depicting the complex helical alignment of fibers throughout the cell wall is constructed. This study demonstrates the unique opportunities SED provides for characterizing the nanoscale hierarchical arrangement of cellulose nanofibers, empowering further research on a range of hybrid materials.

Production of hybrid AgNPs - TEMPO-mediated oxidation cellulose composite from jackfruit peduncle agro-waste and its thermal management application in electronic devices

The urgent need for eco-friendly and cost-effective cellulose paper substrates in thermal management for biomedical electronic devices has driven the exploration of agro-waste materials. In this study, jackfruit peduncle waste was utilized as a precursor to produce a hybrid of AgNPs-tempo-mediated oxidation cellulose strands (AgNPs-TOCS) through acid hydrolysis, TEMPO oxidation, and an in-situ generation process. The resulting hybrid AgNPs-TOCS composite exhibited a cylindrical cellulose structure with a diameter of 27.3 μm, on which spherical AgNPs with a diameter of 16.3 nm were embedded. This hybrid AgNPs-TOCS displayed an impressive inhibition zone diameter against E. coli bacteria (15.2 nm) and exhibited excellent thermal stability up to 269 °C. Furthermore, the AgNPs-TOCS composite paper substrate was fabricated using non-solvent techniques, and its mechanical, thermal, and electrical properties were investigated. This composite paper substrate exhibits good tensile strength (65 ± 2 MPa), in-plane thermal conductivity (5.8 ± 0.2 W/(m·K)), and electrical resistivity (0.0575 KΩ·m). These findings strongly suggest that this type of composite paper substrate holds promise for applications in thermal management within the field of biomedical electronics.

Fast and easy synthesis of silver, copper, and bimetallic nanoparticles on cellulose paper assisted by ultrasound

This work focuses on a systematic method to produce Ag, Cu, and Ag/Cu metallic nanoparticles (MNPs) in situ assisted with ultrasound on cellulose paper. By tuning the concentration of AgNO3 and CuSO4 salt precursors and ultrasound time, combined with a fixed concentration of ascorbic acid (AA) as a reducing agent, it was possible to control the size, morphology, and polydispersity of the resulting MNPs on cellulose papers. Notably, high yield and low polydispersity of MNPs and bimetallic nanoparticles are achieved by increasing the sonication time on paper samples pre-treated with salt precursors before reduction with AA. Moreover, mechanical analysis on paper samples presenting well-dispersed and distributed MNPs showed slightly decreasing values of Young's modulus compared to neat papers. The strain at break is substantially improved in papers containing solely Ag or Cu MNPs. The latter suggests that the elastic/plastic transition and deformation of papers are tuned by cellulose and MNPs interfacial interaction, as indicated by mechanical analysis. The proposed method provides insights into each factor affecting the sonochemistry in situ synthesis of MNPs on cellulose papers. In addition, it offers a straightforward alternative to scale up the production of MNPs on paper, ensuring an eco-friendly method.

Silver nanoparticles loaded on lactose/alginate: in situ synthesis, catalytic degradation, and pH-dependent antibacterial activity

We present the in situ synthesis of silver nanoparticles (AgNPs) through ionotropic gelation utilizing the biodegradable saccharides lactose (Lac) and alginate (Alg). The lactose reduced silver ions to form AgNPs. The crystallite structure of the nanocomposite AgNPs@Lac/Alg, with a mean size of 4-6 nm, was confirmed by analytical techniques. The nanocomposite exhibited high catalytic performance in degrading the pollutants methyl orange and rhodamine B. The antibacterial activity of the nanocomposite is pH-dependent, related to the alterations in surface properties of the nanocomposite at different pH values. At pH 6, the nanocomposite demonstrated the highest antibacterial activity. These findings suggest that this nanocomposite has the potential to be tailored for specific applications in environmental and medicinal treatments, making it a highly promising material.

Preparation of new surface coating based on modified oil-based polymers blended with ZnO and CuZnO NPs for steel protection

In our paper, we have synthesized modified PEA and alkyd resin by replacing the new source of polyol (SDEA) which was confirmed by different analyses such as IR, and 1HNMR spectra. A series of conformal, novel, low-cost, and eco-friendly hyperbranched modified alkyd and PEA resins were fabricated with bio ZnO, CuO/ZnO) NPs through an ex-situ method for mechanical and anticorrosive coatings. The synthesized biometal oxides NPs and its composite modified alkyd and PEA were confirmed by FTIR, SEM with EDEX, TEM, and TGA, and can be stably dispersed into modified alkyd and PEA resins at a low weight fraction of 1%. The nanocomposite coating was also subjected to various tests to determine their surface adhesion, which ranged from (4B-5B), physico-mechanical characteristics such as scratch hardness, which improved from < 1.5 to > 2 kg, gloss (100-135) Specific gravity (0.92-0.96) and also chemical resistance test which passed for water, acid, and solvent except alkali, was poor because of the hydrolyzable ester group in the alkyd and PEA resins. The anti-corrosive features of the nanocomposites were investigated through salt spray tests in 5 wt % NaCl. The results indicate that well-dispersed bio ZnO and CuO/ZnO) NPs (1.0%) in the interior of the hyperbranched alkyd and PEA matrix improve the durability and anticorrosive attributes of the composites, such as degree of rusting, which ranged from 5 to 9, blistering size ranged from 6 to 9, and finally, scribe failure, which ranged from 6 to 9 mm. Thus, they exhibit potential applications in eco- friendly surface coatings. The anticorrosion mechanisms of the nanocomposite alkyd and PEA coating were attributed to the synergistic effect of bio ZnO and (CuO/ZnO) NPs and the prepared modified resins are highly rich in nitrogen elements, which might be regarded as a physical barrier layer for steel substrates.

Biogenic silver based nanostructures: Synthesis, mechanistic approach and biological applications

The alarming impact of antibiotic resistance sparked the quest for complementary treatments to overcome the confrontation over resistant pathogens. Metallic nanoparticles, especially silver nanoparticles (Ag NPs) have gained a much attention because of their remarkable biological characteristics. Moreover, their medicinal properties can be enhanced by preparing the composites with other materials. This article delves a comprehensive review of biosynthesis route for Ag NPs and their nanocomposites (NCs) with in-depth mechanism, methods and favorable experimental parameters. Comprehensive biological features Ag NPs such as antibacterial, antiviral, antifungal have been examined, with a focus on their potential uses in biomedicine and diagnostics has also been discussed. Additionally, we have also explored the hitches and potential outcomes of biosynthesis of Ag NPs in biomedical filed.

Parsimonious methodology for synthesis of silver and copper functionalized cellulose

Metal nanomaterials, such as silver and copper, are often incorporated into commercial textiles to take advantage of their Antibacterial and antiviral properties. The goal of this study was to identify the most parsimonious method for the synthesis of silver, copper, or silver/copper bimetallic treated textiles. To accomplish this eight different methods were employed to synthesize silver, copper, and silver/copper functionalized cotton batting textiles. Using silver and copper nitrate as precursors, different reagents were used to initiate/catalyze the deposition of metal, including: (1) no additive, (2) sodium bicarbonate, (3) green tea, (4) sodium hydroxide, (5) ammonia, (6, 7) sodium hydroxide/ammonia at a 1:2 and 1:4 ratio, and (8) sodium borohydride. The use of sodium bicarbonate as a reagent to reduce silver onto cotton has not been used previously in literature and was compared to established methods. All synthesis methods were performed at 80 °C for one hour following textile addition to the solutions. The products were characterized by x-ray fluorescence (XRF) analysis for quantitative determination of the metal content and x-ray absorption near edge structure (XANES) analysis for silver and copper speciation on the textile. Scanning electron microscopy (SEM) with energy dispersive x-ray (EDX) and size distribution inductively coupled plasma mass spectrometry (ICP-MS) were used to further characterize the products of the sodium bicarbonate, sodium hydroxide, and sodium borohydride synthesis methods following ashing of the textile. For the silver treatment methods (1 mM Ag +), sodium bicarbonate and sodium hydroxide resulted in the highest amounts of silver on the textile (8900 mg Ag/kg textile and 7600 mg Ag/kg textile) and for copper treatment (1 mM Cu +) the sodium hydroxide and sodium hydroxide/ammonium hydroxide resulted in the highest amounts of copper on the textile (3800 mg Ag/kg textile and 2500 mg Ag/kg textile). Formation of copper oxide was dependent on the pH of the solution, with 4 mM ammonia and other high pH solutions resulting in majority of the copper on the textile existing as copper oxide, with smaller amounts of ionic-bound copper. The identified parsimonious methods will lend themselves to the efficient manufacturing of antibacterial and antiviral textiles, or the development of multifunctionalized smart textiles.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10570-023-05099-7.

Bacterial Cellulose/Cellulose Imidazolium Bio-Hybrid Membranes for In Vitro and Antimicrobial Applications

In biomedical applications, bacterial cellulose (BC) is widely used because of its cytocompatibility, high mechanical properties, and ultrafine nanofibrillar structure. However, biomedical use of neat BC is often limited due to its lack of antimicrobial properties. In the current article, we proposed a novel technique for preparing cationic BC hydrogel through in situ incorporation of cationic water-soluble cellulose derivative, cellulose bearing imidazolium tosylate function group (Cell-IMD), in the media used for BC preparation. Different concentrations of cationic cellulose derivative (2, 4, and 6%) were embedded into a highly inter-twined BC nanofibrillar network through the in situ biosynthesis until forming cationic cellulose gels. Cationic functionalization was deeply examined by the Fourier transform infrared (FT-IR), NMR spectroscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) methods. In vitro studies with L929 cells confirmed a good cytocompatibility of BC/cationic cellulose derivatives, and a significant increase in cell proliferation after 7 days, in the case of BC/Cell-IMD3 groups. Finally, antimicrobial assessment against Staphylococcus aureus, Streptococcus mutans, and Candida albicans was assessed, recording a good sensitivity in the case of the higher concentration of the cationic cellulose derivative. All the results suggest a promising use of cationic hybrid materials for biomedical and bio-sustainable applications (i.e., food packaging).

Kinetics, isotherms, and mechanism of removing cationic and anionic dyes from aqueous solutions using chitosan/magnetite/silver nanoparticles

Modified magnetite chitosan with silver nanoparticles was synthesized and tested for removing cationic and anionic dyes in aqueous solutions. Initial dye concentration, pH, and contact time were examined. Results showed that pH (4.0) was optimal for removing anionic dyes (methyl orange) and pH 8.0 for removing cationic dyes (methylene blue). According to these results, zeta potentials were found to be 8.43 and - 39.17 mV at pH 4.0 and 8.0, respectively. So, it is attracted to positively charged cationic dyes in an alkaline medium and negatively charged anionic dyes in an acidic medium because of their opposite charges. Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), thermal gravimetric analysis (TGA), and zeta potential measurements were used to characterize the synthesized nanosorbents. A pseudo-second-order kinetic model is fitted with the Langmuir adsorption model, with an adsorption capacity of 417 and 476 mg/g for methyl orange and methylene blue, respectively. For both dyes, modified magnetite chitosan with silver nanoparticles showed high regeneration capability and recovery for up to four cycles without adsorption efficiency loss. Furthermore, modified magnetite chitosan with silver nanoparticles, as prepared in the present study, was demonstrated to be an effective adsorbent for organic pollutants in wastewater.

Coupling of 3-Aminopropyl Sulfonic Acid to Cellulose Nanofibers for Efficient Removal of Cationic Dyes

A novel anionic nanostructured cellulose derivate was prepared through the coupling of TEMPO-oxidized cellulose nanofibers with 3-aminopropyl sulfonic acid (3-APSA). 3-APSA grafting was variously investigated by FT-IR spectroscopy and transmission electron microscopy (TEM) analysis, confirming a high reaction degree. The surface morphology investigated via scanning electron microscopy (SEM) revealed a more uniform organization of the nanofibers after the 3-APSA coupling, with improvements in terms of fiber packing and pore interconnectivity. This peculiar morphology contributes to improving methylene blue (MB) adsorption and removal efficiency at different operating conditions (pH, initial time, and initial concentration). The results indicated a maximum adsorption capacity of 526 mg/g in the case of 3-APSA grafted nanofibers, over 30% more than that of non-grafted ones (370 mg/g), which confirm a relevant effect of chemical modification on the adsorbent properties of cellulose nanofibers. The adsorption kinetics and isotherms of the current adsorbents match with the pseudo-second-order kinetic and Langmuir isotherm models. This study suggests the use of chemical grafting via 3-APSA is a reliable and facile post-treatment to design bio-sustainable and reusable nanofibers to be used as high-performance adsorbent materials in water pollutant remediation.

Stabilization of Silver Nanoparticles on Polyester Fabric Using Organo-Matrices for Controlled Antimicrobial Performance

Antimicrobial textiles are helpful tools to fight against multidrug-resistant pathogens and nosocomial infections. The deposition of silver nanoparticles (AgNPs) onto textiles has been studied to achieve antimicrobial properties. Yet, due to health and environmental safety concerns associated with such formulations, processing optimizations have been introduced: biocompatible materials, environmentally friendly agents, and delivery platforms that ensure a controlled release. In particular, the functionalization of polyester (PES) fabric with antimicrobial agents is a formulation in high demand in medical textiles. However, the lack of functional groups on PES fabric hinders the development of cost-effective, durable systems that allow a controlled release of antimicrobial agents. In this work, PES fabric was functionalized with AgNPs using one or two biocompatible layers of chitosan or hexamethyldisiloxane (HMDSO). The addition of organo-matrices stabilized the AgNPs onto the fabrics, protected AgNPs from further oxidation, and controlled their release. In addition, the layered samples were efficient against Staphylococcus aureus and Escherichia coli. The sample with two layers of chitosan showed the highest efficacy against S. aureus (log reduction of 2.15 ± 1.08 after 3 h of contact). Against E. coli, the sample with two layers of chitosan showed the best properties. Chitosan allowed to control the antimicrobial activity of AgNPs, avoid the complete loss of AgNPs after washings and act in synergy with AgNPs. After 3 h of incubation, this sample presented a log reduction of 4.81, and 7.27 of log reduction after 5 h of incubation. The antimicrobial results after washing showed a log reduction of 3.47 and 4.88 after 3 h and 5 h of contact, respectively. Furthermore, the sample with a final layer of HMDSO also presented a controlled antimicrobial effect. The antimicrobial effect was slower than the sample with just an initial layer of HMDSO, with a log reduction of 4.40 after 3 h of incubation (instead of 7.22) and 7.27 after 5 h. The biocompatibility of the composites was confirmed through the evaluation of their cytotoxicity towards HaCaT cells (cells viability > 96% in all samples). Therefore, the produced nanocomposites could have interesting applications in medical textiles once they present controlled antimicrobial properties, high biocompatibility and avoid the complete release of AgNPs to the environment.

Use of Nanocellulose to Produce Water-Based Conductive Inks with Ag NPs for Printed Electronics

The need for more sustainable printed electronics has emerged in the past years. Due to this, the use of nanocellulose (NC) extracted from cellulose has recently been demonstrated to provide interesting materials such as functional inks and transparent flexible films due to its properties. Its high specific surface area together with the high content of reactive hydroxyl groups provide a highly tailorable surface chemistry with applications in ink formulations as a stabilizing, capping, binding and templating agent. Moreover, NC mechanical, physical and thermal properties (high strength, low porosity and high thermal stability, respectively) provide an excellent alternative for the currently used plastic films. In this work, we present a process for the production of water-based conductive inks that uses NC both as a template for silver nanoparticles (Ag NPs) formation and as an ink additive for ink formulation. The new inks present an electrical conductivity up to 2 × 10⁶ S/m, which is in the range of current commercially available conductive inks. Finally, the new Ag NP/NC-based conductive inks have been tested to fabricate NFC antennas by screen-printing onto NC-coated paper, demonstrating to be operative.

Cellulose Amphiphilic Materials: Chemistry, Process and Applications

In the last decade, amphiphilic cellulose (AC) is emerging as attractive biomaterial for different therapeutic use, due to its unique chemical and physical properties. Using it as alternative to synthetic polymers, AC opens up new avenues to prepare new bio-sustainable materials with low impact in the cellular environment. Herein, most recent methods to synthesize and processing AC materials from different sources—i.e., cellulose nanofibers, bacterial cellulose, cellulose derivatives—will be discussed. By an accurate optimization of morphology and surface chemistry, it is possible to develop innovative amphiphilic platforms, promising for a wide range of biomedical applications, from drug delivery to molecular/particle adsorption.