Non-Thermal Plasma Coupled with Catalyst for the Degradation of Water Pollutants: A Review

A comprehensive insight on plasma-catalytic degradation of organic pollutants in water: Comparison between ZnO and TiO2

A novel system combining underwater plasma bubbles and high voltage nanopulses was combined for the first time with ZnO and TiO2 for the degradation of organic pollutants in water. The effect of catalyst loading, discharge power and plasma gas on pollutant degradation was investigated whereas the plasma-catalytic mechanism was explored through the quantification of plasma species, COD/TOC measurements and scavenging experiments in the presence and absence of catalysts. The increased efficiency in the presence of either ZnO or TiO2, especially under plasma gases (air and oxygen) able to produce UV radiation in the range of wavelengths absorbed by both catalysts, lies on the increased concentration of the critical reactive species (e.g. ·O2-, ·ΟΗ, H2O2). Compared to plasma alone process, H2O2 was significantly enhanced in the presence of TiO2 and decreased in the presence of ZnO, whereas ·OH concentration was higher in the plasma-ZnO but lower in the plasma-TiO2 system which supports the overall superior performance of ZnO compared to TiO2. The synergy of plasma-ZnO process compared to that of plasma-TiO2 was ∼2.4 and ∼1.5 times higher for Orange II (OII) and Methylene Blue (MB), respectively, exhibiting a very low electrical energy per order (1.4 kWh m-3 for OII and 0.31 kWh m-3 or MB). The present effort contributes on providing fundamental insights and further expand of plasma-catalysis for water treatment.

Dielectric barrier discharge plasma catalysis as an alternative approach for the synthesis of ammonia: a review

Numerous researchers have attempted to provide mild reactions and environmentally-friendly methods for NH3 synthesis. Research on non-thermal plasma-assisted ammonia synthesis, notably the atmospheric-pressure nonthermal plasma synthesis of ammonia over catalysts, has recently gained attention in the academic literature. Since non-thermal plasma technology circumvents the existing crises and harsh conditions of the Haber-Bosch process, it can be considered as a promising alternative for clean synthesis of ammonia. Non-thermal dielectric barrier discharge (DBD) plasma has been extensively employed in the synthesis of ammonia due to its particular advantages such as the simple construction of DBD reactors, atmospheric operation at ambient temperature, and low cost. The combination of this plasma and catalytic materials can remarkably affect ammonia formation, energy efficiency, and the generation of by-products. The present article reviews plasma-catalysis ammonia synthesis in a dielectric barrier discharge reactor and the parameters affecting this synthesis system. The proposed mechanisms of ammonia production by this plasma catalysis system are discussed as well.

Advances of non-thermal plasma discharge technology in degrading recalcitrant wastewater pollutants. A comprehensive review

With development and urbanization, the amount of wastewater generated due to human activities drastically increases yearly, causing water pollution and intensifying the already worsened water crisis. Although convenient, conventional wastewater treatment methods such as activated sludge, stabilization ponds, and adsorption techniques cannot fully eradicate the complex and recalcitrant contaminants leading to toxic byproducts generation. Recent advancements in wastewater treatment techniques, specifically non-thermal plasma technology, have been extensively investigated for the degradation of complex pollutants in wastewater. Non-thermal plasma is an effective alternative for degrading and augmenting the biodegradability of recalcitrant pollutants due to its ability to generate reactive species in situ. This article critically reviews the non-thermal plasma technology, considering the plasma discharge configuration and reactor types. Furthermore, the influence of operational parameters on the efficiency of the plasma systems and the reactive species generated by the system during discharge has gained significant interest and hence been discussed. Also, the application of non-thermal plasma technology for the degradation of pharmaceuticals, pesticides, and dyes and the inactivation of microbial activities are outlined in this review article. Additionally, optimistic applications involving the combination of non-thermal plasma and catalysts and pilot and industrial-scale projects utilizing non-thermal plasma technology have been addressed. Concluding perceptions on the challenges and future perspectives of the non-thermal technology on wastewater treatment are accentuated. Overall, this review outlines a comprehensive understanding of the non-thermal plasma technology for recalcitrant pollutant degradation from a scientific perspective providing detailed instances for reference.

Removal of Azo Dyes from Wastewater through Heterogeneous Photocatalysis and Supercritical Water Oxidation

Azo dyes are synthetic organic dyes used in the textile, leather, and paper industries. They pose environmental problems due to their toxic and persistent nature. The toxicity is due to the presence of azo groups in the dye molecule that can break down into aromatic amines, which are highly toxic to aquatic organisms and humans. Various treatment methods have been developed to remove azo dyes from wastewater. Conventional wastewater treatments have some drawbacks, such as high operating costs, long processing times, generation of sludge, and the formation of toxic by-products. For these reasons, a valid alternative is constituted by advanced oxidation processes. Good results have been obtained using heterogeneous photocatalysis and supercritical water oxidation. In the former method, a photocatalyst is in contact with wastewater, a suitable light activates the catalyst, and generated reactive oxygen species that react with pollutants through oxidative reactions to their complete mineralization; the latter involves pressurizing and heating wastewater to supercritical conditions in a reactor vessel, adding an oxidizing agent to the supercritical water, and allowing the mixture to react. In this review paper, works in the literature that deal with processing wastewater containing azo dyes through photocatalysts immobilized on macroscopic supports (structured photocatalysts) and the supercritical water oxidation technique have been critically analyzed. In particular, advancement in the formulation of structured photocatalysts for the degradation of azo dyes has been shown, underlying different important features, such as the type of support for the photoactive phase, reactor configuration, and photocatalytic efficiency in terms of dye degradation and photocatalyst stability. In the case of supercritical water oxidation, the main results regarding COD and TOC removal from wastewater containing azo dyes have been reported, taking into account the reactor type, operating pressure, and temperature, as well as the reaction time.

Volatile organic compounds degradation by nonthermal plasma: a review

Volatile organic compounds (VOCs) have posed a severe threat on both ecosystem and human health which thus have gained much attention in recent years. Nonthermal plasma (NTP) as an alternative to traditional methods has been employed to degrade VOC in the atmosphere and wastewater for its high removal efficiency (up to 100%), mild operating conditions, and environmental friendliness. This review outlined the principles of NTP production and the applications on VOC removal in different kinds of reactors, like single/double dielectric barrier discharge, surface discharge, and gliding arc discharge reactors. The combination of NTP with catalysts/oxidants was also applied for VOC degradation to further promote the energy efficiency. Further, detailed explanations were given of the effect of various important factors including input/reactor/external conditions on VOC degradation performance. The reactive species (e.g., high-energy electrons, HO·, O·, N₂⁺, Ar⁺, O₃, H₂O₂) generated in NTP discharge process have played crucial roles in decomposing VOC molecules; therefore, their variation under different parameter conditions along with the reaction mechanisms involved in these NTP technologies was emphatically explained. Finally, a conclusion of the NTP technologies was presented, and special attention was paid to future challenges for NTP technologies in VOC treatment to stimulate the advances in this topic.

Non-Thermal Plasma as a Biomass Pretreatment in Biorefining Processes

Climatic changes and the growing population call for innovative solutions that are able to produce biochemicals by adopting environmentally sustainable procedures. The biorefinery concept meets this requirement. However, one of the main drawbacks of biorefineries is represented by the feedstocks’ pretreatment. Lately, scientific research has focused on non-thermal plasma, which is an innovative and sustainable pretreatment that is able to obtain a high sugar concentration. In the present review, literature related to the use of non-thermal plasma for the production of fermentable sugar have been collected. In particular, its sugar extraction, time, and energy consumption have been compared with those of traditional biomass pretreatments. As reported, on one hand, this emerging technology is characterized by low costs and no waste production; on the other hand, the reactor’s configuration must be optimized to reduce time and energy demand.

Possible Synergies of Nanomaterial-Assisted Tissue Regeneration in Plasma Medicine: Mechanisms and Safety Concerns

Cold atmospheric plasma and nanomedicine originally emerged as individual domains, but are increasingly applied in combination with each other. Most research is performed in the context of cancer treatment, with only little focus yet on the possible synergies. Many questions remain on the potential of this promising hybrid technology, particularly regarding regenerative medicine and tissue engineering. In this perspective article, we therefore start from the fundamental mechanisms in the individual technologies, in order to envision possible synergies for wound healing and tissue recovery, as well as research strategies to discover and optimize them. Among these strategies, we demonstrate how cold plasmas and nanomaterials can enhance each other's strengths and overcome each other's limitations. The parallels with cancer research, biotechnology and plasma surface modification further serve as inspiration for the envisioned synergies in tissue regeneration. The discovery and optimization of synergies may also be realized based on a profound understanding of the underlying redox- and field-related biological processes. Finally, we emphasize the toxicity concerns in plasma and nanomedicine, which may be partly remediated by their combination, but also partly amplified. A widespread use of standardized protocols and materials is therefore strongly recommended, to ensure both a fast and safe clinical implementation.

Nanomaterial-enabled photothermal-based solar water disinfection processes: Fundamentals, recent advances, and mechanisms

The pathogenic microorganisms in water pose a great threat to human health. Photothermal and photothermocatalytic disinfection using nanomaterials (NPs) has offered a promising and effective strategy to address the challenges in solar water disinfection (SODIS), especially in the point-of-use operations. This review aims at providing comprehensive and state-of-the-art knowledge of photothermal-based disinfection by NPs. The fundamentals and principles of photothermal-based disinfection were first introduced. Then, recent advances in developing photothermal/photothermocatalytic catalysts were systematically summarized. The light-to-heat conversion and disinfection performance of a large variety of photothermal materials were presented. Given the complicated mechanisms of photothermal-based disinfection, the attacks from reactive oxygen species and heat, the destruction of bacterial cells, and the antibacterial effects of released metal ions were highlighted. Finally, future challenges and opportunities associated with the development of cost-effective photothermal/photothermocatalytic disinfection systems were outlined. This review will provide guidance in designing future NPs and inspire more research efforts from environmental nano-communities to move towards practical water disinfection operations.

Recent Advances of Emerging Organic Pollutants Degradation in Environment by Non-Thermal Plasma Technology: A Review

Emerging organic pollutants (EOPs), including endocrine disrupting compounds (EDCs), pharmaceuticals and personal care products (PPCPs), and persistent organic pollutants (POPs), constitute a problem in the environmental field as they are difficult to completely degrade by conventional treatment methods. Non-thermal plasma technology is a novel advanced oxidation process, which combines the effects of free radical oxidation, ozone oxidation, ultraviolet radiation, shockwave, etc. This paper summarized and discussed the research progress of non-thermal plasma remediation of EOPs-contaminated water and soil. In addition, the reactive species in the process of non-thermal plasma degradation of EOPs were summarized, and the degradation pathways and degradation mechanisms of EOPs were evaluated of selected EOPs for different study cases. At the same time, the effect of non-thermal plasma in synergy with other techniques on the degradation of EOPs in the environment was evaluated. Finally, the bottleneck problems of non-thermal plasma technology are summarized, and some suggestions for the future development of non-thermal plasma technology in the environmental remediation were presented. This review contributes to our better understanding of non-thermal plasma technology for remediation of EOPs-contaminated water and soil, hoping to provide reference for relevant practitioners.

Recent Advances in Endocrine Disrupting Compounds Degradation through Metal Oxide-Based Nanomaterials

Endocrine Disrupting Compounds (EDCs) comprise a class of natural or synthetic molecules and groups of substances which are considered as emerging contaminants due to their toxicity and danger for the ecosystems, including human health. Nowadays, the presence of EDCs in water and wastewater has become a global problem, which is challenging the scientific community to address the development and application of effective strategies for their removal from the environment. Particularly, catalytic and photocatalytic degradation processes employing nanostructured materials based on metal oxides, mainly acting through the generation of reactive oxygen species, are widely explored to eradicate EDCs from water. In this review, we report the recent advances described by the major publications in recent years and focused on the degradation processes of several classes of EDCs, such as plastic components and additives, agricultural chemicals, pharmaceuticals, and personal care products, which were realized by using novel metal oxide-based nanomaterials. A variety of doped, hybrid, composite and heterostructured semiconductors were reported, whose performances are influenced by their chemical, structural as well as morphological features. Along with photocatalysis, alternative heterogeneous advanced oxidation processes are in development, and their combination may be a promising way toward industrial scale application.

An insightful analysis of dimethyl phthalate degradation by the collaborative process of DBD plasma and Graphene-WO3 nanocomposites

In this paper, the prepared graphene-WO₃ nanocomposites (rGO-WO₃) were added into a dielectric barrier discharge (DBD) plasma system with spiral discharge electrode to set up a collaborative process to treat the dimethyl phthalate (DMP) in water. Degradation of the DMP under different experimental conditions were studied to illustrate the catalysis of the rGO-WO₃ in the DBD plasma system. The obtained results proved that there was the catalysis of the rGO-WO₃ for the DMP degradation within the studied DMP concentration, solution initial pH values and conductivities. From the results of the energy utilization efficiency (G₅₀) analysis, the catalysis was more apparent in the case of the oxygen bubbling system than that in the nitrogen or the air bubbling system, which was due to the higher oxygen constitution in the oxygen bubbling system. The reduction of the measured liquid phase ozone concentrations in the DBD/rGO-WO₃ system bubbled with air as well as oxygen than those measured in the sole DBD system, which verified the consumption of the ozone by the catalysis of the rGO-WO₃. Furthermore, the UV-Vis and the three-dimensional fluorescence spectra analysis were also carried out to state the catalytic effect of the rGO-WO₃ for the DMP degradation. Toxicity analysis for the degradation byproducts confirmed the collaborative process could reduce the negative effect of the original DMP on the environment.

Non-thermal plasma irradiated polyaluminum chloride for the heterogeneous adsorption enhancement of Cs+ and Sr2+ in a binary system

The natural ecosystem will continually deteriorate for decades by the leakage of Cs and Sr isotopes. The exploration of the new materials or techniques for the efficient treatment of radioactive wastewater is critically important. In this study, a dielectric barrier discharge (DBD) configuration was constructed to operate the non-thermal plasma (NTP). The NTP was incorporated into the synthesis of polyaluminum chloride (PAC) in two different procedures to intensify the synthesis of PAC (NTP-PAC) and enhance the further removal of Cs and Sr from wastewater. The employment of NTP in two procedures both had significantly changed the physicochemical characteristics of PAC materials, which facilitated the further adsorption application of NTP-PAC on the treatment of Cs⁺ and Sr²⁺. Different molecular, morphological, and adsorption characteristics were confirmed to the NTP-PAC materials. The heterogeneous adsorption of the NTP-PAC can be appropriately fitted by both the pseudo-first-order kinetic model and the Elovich model. Both physisorption and chemisorption reaction mechanisms were ensured for the heterogeneous adsorption of the NTP-PAC material towards Cs⁺ and Sr²⁺, which guaranteed the excellent adsorption performance of NTP-PAC materials compared to PAC. The electron collisions caused by NTP with alum pulp created highly reactive growth precursors and intensified the nucleation and hydrolysis polymerization of PAC. The employment of NTP explicitly broadens the reaction pathways between PAC and cationic contaminants in the aqueous environment, which expands the application area of PAC materials in environmental sustainability.

Photocatalytic degradation-based efficient elimination of pesticides using ruthenium/gold metal nanoparticle-anchored zirconium dioxide

Ruthenium and gold metal nanoparticles-incorporated zirconium dioxide (ZrO2@Ru and ZrO2@Au) nanostructures were developed as promising photocatalysts for wastewater remediation.

Recent Progress and Prospects in Catalytic Water Treatment

Presently, conventional technologies in water treatment are not efficient enough to completely mineralize refractory water contaminants. In this context, the implementation of catalytic processes could be an alternative. Despite the advantages provided in terms of kinetics of transformation, selectivity, and energy saving, numerous attempts have not yet led to implementation at an industrial scale. This review examines investigations at different scales for which controversies and limitations must be solved to bridge the gap between fundamentals and practical developments. Particular attention has been paid to the development of solar-driven catalytic technologies and some other emerging processes, such as microwave assisted catalysis, plasma-catalytic processes, or biocatalytic remediation, taking into account their specific advantages and the drawbacks. Challenges for which a better understanding related to the complexity of the systems and the coexistence of various solid-liquid-gas interfaces have been identified.

Effect of microwave plasma treatment on magnetic and photocatalytic response of manganese ferrite nanoparticles for wastewater treatment

The conventionally synthesized nano-ferrite materials do not possess bulk properties, generally required for their use in mainstream industry. To make ferrite nanoparticles clinically applicable materials, it is important to have good control over morphology and optical properties of these materials. In this study, low-pressure microwave plasma was used to tailor the structural properties and surface chemistry of manganese ferrite nanoparticles. A facile sol-gel method was used to prepare cubic spinal structures of manganese ferrite nanoparticles. These nanoparticles were exposed to oxygen plasma sustained with a microwave source for improving their magnetic and photocatalytic activities. The techniques like XRD, SEM, PL, UV-Vis DRS, transient photocurrent response and EIS were used to characterize the samples. The plasma treated nanoparticles were used to degraded methyl blue (MB) dye in the solution. The photocatalytic activity showed 85% degradation of MB after 100 min of exposure of visible light. The second part of the paper studied the magnetic properties of the nanoparticles. The saturation magnetization decreased from 0.78 emu/g to 0.68 emu/g after plasma treatment of nanoparticles.

Non-Thermal Plasma-Assisted Catalytic Reactions for Environmental Protection

“Non-thermal plasma technology” (NTP) has notably increased [...]