The Applications of Morphology Controlled ZnO in Catalysis

Preparation and Application of Co-Doped Zinc Oxide: A Review

Due to a wide band gap and large exciton binding energy, zinc oxide (ZnO) is currently receiving much attention in various areas, and can be prepared in various forms including nanorods, nanowires, nanoflowers, and so on. The reliability of ZnO produced by a single dopant is unstable, which in turn promotes the development of co-doping techniques. Co-doping is a very promising technique to effectively modulate the optical, electrical, magnetic, and photocatalytic properties of ZnO, as well as the ability to form various structures. In this paper, the important advances in co-doped ZnO nanomaterials are summarized, as well as the preparation of co-doped ZnO nanomaterials by using different methods, including hydrothermal, solvothermal, sol-gel, and acoustic chemistry. In addition, the wide range of applications of co-doped ZnO nanomaterials in photocatalysis, solar cells, gas sensors, and biomedicine are discussed. Finally, the challenges and future prospects in the field of co-doped ZnO nanomaterials are also elucidated.

Influence of Synthesis Conditions on the Properties of Zinc Oxide Obtained in the Presence of Nonionic Structure-Forming Compounds

This work investigated the influence of synthesis conditions, including the use of nonionic structure-forming compounds (surfactants) with different molecular weights (400-12,600 g/mol) and various hydrophilic/hydrophobic characteristics, as well as the use of a glass substrate and hydrothermal exposure on the texture and structural properties of ZnO samples. By X-ray analysis, it was determined that the synthesis intermediate in all cases is the compound Zn5(OH)8(NO3)2∙2H2O. It was shown that thermolysis of this compound at 600 °C, regardless of the physicochemical properties of the surfactants, leads to the formation of ZnO with a wurtzite structure and spherical or oval particles. The particle size increased slightly as the molecular weight and viscosity of the surfactants grew, from 30 nm using Pluronic F-127 (MM = 12,600) to 80 nm using Pluronic L-31 (MM = 1100), PE-block-PEG (MM = 500) and PEG (MM = 400). Holding the pre-washed synthetic intermediates (Zn5(OH)8(NO3)2∙2H2O) under hydrothermal conditions resulted in the formation of hexagonal ZnO rod crystal structures of various sizes. It was shown that the largest ZnO particles (10-15 μm) were observed in a sample obtained during hydrothermal exposure using Pluronic P-123 (MM = 5800). Atomic adsorption spectroscopy performed comparative quantitative analysis of residual Zn2+ ions in the supernatant of ZnO samples with different particle sizes and shapes. It was shown that the residual amount of Zn2+ ions was higher in the case of examining ZnO samples which have spherical particles of 30-80 nm. For example, in the supernatant of a ZnO sample that had a particle size of 30 nm, the quantitative content of Zn2+ ions was 10.22 mg/L.

The Suitability of Photocatalyst Precursor Materials in Geopolymer Coating Applications: A Review

Today, the building and construction sector demands environmentally friendly and sustainable protective coatings using inorganic coating materials for safe, non-hazardous, and great performance. Many researchers have been working on sustainable solutions to protect concrete and metal infrastructures against corrosion and surface deterioration with the intention of introducing green alternatives to conventional coatings. This article presents a review of developments of geopolymer pastes doped with different types of photocatalyst precursors including factors affecting geopolymer properties for enhancing coating with photocatalytic performance. Photodegradation using geopolymer photocatalyst has great potential for resolving harmless substances and removing pollutants when energized with ultraviolet (UV) light. Although geopolymer is a potentially new material with great properties, there has been less research focusing on the development of this coating. This study demonstrated that geopolymer binders are ideal precursor support materials for the synthesis of photocatalytic materials, with a significant potential for optimizing their distinctive properties.

Evaluation of the Photocatalytic Activity of Distinctive-Shaped ZnO Nanocrystals Synthesized Using Latex of Different Plants Native to the Amazon Rainforest

ZnO nanocrystals with three different morphologies have been synthesized via a simple sol-gel-based method using Brosimum parinarioides (bitter Amapá) and Parahancornia amapa (sweet Amapá) latex as chelating agents. X-ray diffraction (XRD) and electron diffraction patterns (SAED) patterns showed the ZnO nanocrystals were a pure hexagonal wurtzite phase of ZnO. XRD-based spherical harmonics predictions and HRTEM images depicted that the nanocrystallites constitute pitanga-like (~15.8 nm), teetotum-like (~16.8 nm), and cambuci-like (~22.2 nm) shapes for the samples synthesized using bitter Amapá, sweet Amapá, and bitter/sweet Amapá chelating agent, respectively. The band gap luminescence was observed at ~2.67-2.79 eV along with several structural defect-related, blue emissions at 468-474 nm (V_O, V_Zn, Zn_i), green emissions positioned at 513.89-515.89 (h-VO+), and orange emission at 600.78 nm (VO+-VO++). The best MB dye removal efficiency (85%) was mainly ascribed to the unique shape and oxygen vacancy defects found in the teetotum-like ZnO nanocrystals. Thus, the bitter Amapá and sweet Amapá latex are effective chelating agents for synthesizing distinctive-shaped ZnO nanocrystals with highly defective and remarkable photocatalytic activity.

Plant-Based Bimetallic Silver-Zinc Oxide Nanoparticles: A Comprehensive Perspective of Synthesis, Biomedical Applications, and Future Trends

The universal emphasis on the study of green nanotechnology has led to biologically harmless uses of wide-ranged nanomaterials. Nanotechnology deals with the production of nanosized particles with regular morphology and properties. Various researches have been directed on nanomaterial synthesis by physical, chemical, and biological means. Understanding the safety of both environment and in vivo, a biogenic approach particularly plant-derived synthesis is the best strategy. Silver-zinc oxide nanoparticles are most effective. Moreover, these engineered nanomaterials via morphological modifications attain improved performance in antimicrobial, biomedical, environmental, and therapeutic applications. This article evaluates manufacturing strategies for silver-zinc oxide nanoparticles via plant-derived means along with highlighting their broad range of uses in bionanotechnology.

Catalytic reduction of 4-nitrophenol using CuO@Na2Ti(PO4)2⋅H2O

This article presents the synthesis, property characterization and catalytic application of CuO-supported disodium titanium phosphate, (CuO@Na₂Ti(PO₄)₂⋅H₂O) for the reduction of industrial pollutant 4-nitrophenol (4-NP). A simple hydrothermal route was developed to synthesize CuO@Na₂Ti(PO₄)₂⋅H₂O catalyst (CuO@Na₂TiP) from beach sand ilmenite. The prepared CuO@Na₂TiP was characterized using X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy, and nitrogen adsorption-desorption isotherms. The catalyst 12 wt.% CuO@Na₂TiP showed the fastest reduction kinetics for 4-NP.

Controlled Metal-Support Interactions in Au/CeO2-Mg(OH)2 Catalysts Activating the Direct Oxidative Esterification of Methacrolein with Methanol to Methyl Methacrylate

The strong metal-support interaction (SMSI) between the three components in Au/CeO₂-Mg(OH)₂ can be controlled by the relative composition of CeO₂ and Mg(OH)₂ and by the calcination temperature for the direct oxidative esterification of methacrolein (MACR) with methanol to methyl methacrylate (MMA). The composition ratio of CeO₂ and Mg(OH)₂ in the catalyst affects the catalytic performance dramatically. An Au/CeO₂ catalyst without Mg(OH)₂ esterified MACR to a hemiacetal species without MMA production, which confirmed that Mg(OH)₂ is a prerequisite for successful oxidative esterification. When Au/Mg(OH)₂ was used without CeO₂, the direct oxidative esterification of MACR was successful and produced MMA, the desired product. However, the MMA selectivity was much lower (72.5%) than that with Au/CeO₂-Mg(OH)₂ catalysts, which have an MMA selectivity of 93.9-99.8%, depending on the relative composition of CeO₂ and Mg(OH)₂. In addition, depending on the calcination temperature, the crystallinity of the CeO₂-Mg(OH)₂ and the surface acidity/basicity can be remarkably changed. Consequently, the Au-nanoparticle-supported catalysts exhibited different MACR conversions and MMA selectivities. The catalytic behavior can be explained by the different metal-support interactions between the three components depending on the composition ratio of CeO₂ and Mg(OH)₂ and the calcination temperature. These differences were evidenced by X-ray diffraction, X-ray photoelectron spectroscopy, and CO₂ temperature-programmed desorption. The present study provides new insights into the design of SMSI-induced supported metal catalysts for the development of multifunctional heterogeneous catalysts.

Synthesis and Characterization of Titanium Dioxide Hollow Nanofiber for Photocatalytic Degradation of Methylene Blue Dye

Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one-dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light-harvesting properties and an anatase–rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m²/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H₂O₂ concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation.

Zinc Oxide Phytonanoparticles' Effects on Yield and Mineral Contents in Fruits of Tomato (Solanum lycopersicum L. cv. Cherry) under Field Conditions

The use of phytonanoparticles in agriculture could decrease the use of fertilizers and therefore decrease soil contamination, due to their size being better assimilated in plants. It is important to mention that the nanofertilizer is slow-releasing and improves plant physiological properties and various nutritional parameters. The influence of soil and foliar applications of phytonanoparticles of ZnO with the Moringa oleifera extract under three concentrations (25, 50, and 100 ppm) was evaluated on the cherry tomato crop (Solanum lycopersicum L.). Synthesis of the phytonanoparticles was analyzed with ultraviolet-visible spectroscopy (UV-Vis) and infrared transmission spectroscopy with Fourier transform (FT-IR), as well as the analysis with the dynamic light scattering (DLS) technique. The morphometric parameters were evaluated before and after the application of the nanoparticles. The minerals' content of fruits was done 95 days after planting. Results showed that soil application was better at a concentration of 25 ppm of phytonanoparticles since it allowed the greatest number of flowers and fruits on the plant; however, it was demonstrated that when performing a foliar application, the fruit showed the highest concentrations for the elements Mg, Ca, and Na at concentrations of 511, 4589, and 223 mg kg⁻¹, respectively.

Ag@ZnO/MWCNT ternary nanocomposite as an active and stable catalyst for the 4-nitrophenol reduction in water

The nitroaromatic compounds, known as organic pollutants, have arising attention due to their carcinogenic character, highly dangerous to human health. In this work, the Ag@ZnO/MWCNT ternary nanocomposite synthesized via conjugation of sonochemical and solvothermal treatments manifests high performance in the reduction of 4-nitrophenol in the aqueous media (TOF value of 246 min^-1μmol metal^-1). The incorporation of MWCNT onto the nanocomposite structure favored the reusing of the catalysts even after eight consecutive catalytic runs without catalysts cleaning nor product removal. Obtained samples were characterized by XRD, TEM, UV-vis, Raman and FTIR spectroscopies. It was found that ultrasonic treatment at relatively moderate conditions leads to functionalization of MWCNT, the appearance of C=C and OH groups and change of electronic properties of Ag@ZnO/MWCNT composite which provide its stable material dispersion in aqueous solution and high catalytic performance in the 4-nitrophenol reduction. This technique may be effectively applied for the functionalization of carbon including materials for their usage in an aqueous media.

ZnO nucleation into trititanate nanotubes by ALD equipment techniques, a new way to functionalize layered metal oxides

In this contribution, we explore the potential of atomic layer deposition (ALD) techniques for developing new semiconductor metal oxide composites. Specifically, we investigate the functionalization of multi-wall trititanate nanotubes, H₂Ti₃O₇ NTs (sample T1) with zinc oxide employing two different ALD approaches: vapor phase metalation (VPM) using diethylzinc (Zn(C₂H₅)₂, DEZ) as a unique ALD precursor, and multiple pulsed vapor phase infiltration (MPI) using DEZ and water as precursors. We obtained two different types of tubular H₂Ti₃O₇ species containing ZnO in their structures. Multi-wall trititanate nanotubes with ZnO intercalated inside the tube wall sheets were the main products from the VPM infiltration (sample T2). On the other hand, MPI (sample T3) principally leads to single-wall nanotubes with a ZnO hierarchical bi-modal functionalization, thin film coating, and surface decorated with ZnO particles. The products were mainly characterized by electron microscopy, energy dispersive X-ray, powder X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. An initial evaluation of the optical characteristics of the products demonstrated that they behaved as semiconductors. The IR study revealed the role of water, endogenous and/or exogenous, in determining the structure and properties of the products. The results confirm that ALD is a versatile tool, promising for developing tailor-made semiconductor materials.

Hollow, mesoporous, eutectic Zn1−xMgxO nano-spheres as solid acid–base catalysts for the highly regio-selective O-methylation of 1,2-diphenols

Hollow, mesoporous and eutectic Zn1−xMgxO nanospheres promote the highly selective O-methylation of 1,2-diphenols to afford mono-ethers in complete conversion together with excellent mono-ether selectivities via single-site activation model.

A Review of Microwave Synthesis of Zinc Oxide Nanomaterials: Reactants, Process Parameters and Morphoslogies

Zinc oxide (ZnO) is a multifunctional material due to its exceptional physicochemical properties and broad usefulness. The special properties resulting from the reduction of the material size from the macro scale to the nano scale has made the application of ZnO nanomaterials (ZnO NMs) more popular in numerous consumer products. In recent years, particular attention has been drawn to the development of various methods of ZnO NMs synthesis, which above all meet the requirements of the green chemistry approach. The application of the microwave heating technology when obtaining ZnO NMs enables the development of new methods of syntheses, which are characterised by, among others, the possibility to control the properties, repeatability, reproducibility, short synthesis duration, low price, purity, and fulfilment of the eco-friendly approach criterion. The dynamic development of materials engineering is the reason why it is necessary to obtain ZnO NMs with strictly defined properties. The present review aims to discuss the state of the art regarding the microwave synthesis of undoped and doped ZnO NMs. The first part of the review presents the properties of ZnO and new applications of ZnO NMs. Subsequently, the properties of microwave heating are discussed and compared with conventional heating and areas of application are presented. The final part of the paper presents reactants, parameters of processes, and the morphology of products, with a division of the microwave synthesis of ZnO NMs into three primary groups, namely hydrothermal, solvothermal, and hybrid methods.

Atomic Layer Deposition of ZnO on Mesoporous Silica: Insights into Growth Behavior of ZnO via In-Situ Thermogravimetric Analysis

ZnO is a remarkable material with many applications in electronics and catalysis. Atomic layer deposition (ALD) of ZnO on flat substrates is an industrially applied and well-known process. Various studies describe the growth of ZnO layers on flat substrates. However, the growth characteristics and reaction mechanisms of atomic layer deposition of ZnO on mesoporous powders have not been well studied. This study investigates the ZnO ALD process based on diethylzinc (DEZn) and water with silica powder as substrate. In-situ thermogravimetric analysis gives direct access to the growth rates and reaction mechanisms of this process. Ex-situ analytics, e.g., N₂ sorption analysis, XRD, XRF, HRTEM, and STEM-EDX mapping, confirm deposition of homogenous and thin films of ZnO on SiO₂. In summary, this study offers new insights into the fundamentals of an ALD process on high surface area powders.

Self-Aligned Hierarchical ZnO Nanorod/NiO Nanosheet Arrays for High Photon Extraction Efficiency of GaN-Based Photonic Emitter

Advancements in nanotechnology have facilitated the increased use of ZnO nanostructures. In particular, hierarchical and core–shell nanostructures, providing a graded refractive index change, have recently been applied to enhance the photon extraction efficiency of photonic emitters. In this study, we demonstrate self-aligned hierarchical ZnO nanorod (ZNR)/NiO nanosheet arrays on a conventional photonic emitter (C-emitter) with a wavelength of 430 nm. These hierarchical nanostructures were synthesized through a two-step hydrothermal process at low temperature, and their optical output power was approximately 17% higher than that of ZNR arrays on a C-emitter and two times higher than that of a C-emitter. These results are due to the graded index change in refractive index from the GaN layer inside the device toward the outside as well as decreases in the total internal reflection and Fresnel reflection of the photonic emitter.

Morphology engineering of ZnO nanorod arrays to hierarchical nanoflowers for enhanced photocatalytic activity and antibacterial action against Escherichia coli

A facile, efficient hydrothermal synthesis of ZnO nanoflowers followed by post-synthetic annealing and their photocatalytic and antibacterial properties are reported.

Metal–support interactions on Ru/CaAlOx catalysts derived from structural reconstruction of Ca–Al layered double hydroxides for ammonia decomposition

Strong metal–support interaction (SMSI) over Ru/CaAlO_x was constructed by utilizing the surface structural reconstruction of Ca–Al layered double hydroxides (LDHs) in aqueous solution and their subsequent hydroxide-to-oxide transformations.

Advances in Methanol Production and Utilization, with Particular Emphasis toward Hydrogen Generation via Membrane Reactor Technology

Methanol is currently considered one of the most useful chemical products and is a promising building block for obtaining more complex chemical compounds, such as acetic acid, methyl tertiary butyl ether, dimethyl ether, methylamine, etc. Methanol is the simplest alcohol, appearing as a colorless liquid and with a distinctive smell, and can be produced by converting CO₂ and H₂, with the further benefit of significantly reducing CO₂ emissions in the atmosphere. Indeed, methanol synthesis currently represents the second largest source of hydrogen consumption after ammonia production. Furthermore, a wide range of literature is focused on methanol utilization as a convenient energy carrier for hydrogen production via steam and autothermal reforming, partial oxidation, methanol decomposition, or methanol⁻water electrolysis reactions. Last but not least, methanol supply for direct methanol fuel cells is a well-established technology for power production. The aim of this work is to propose an overview on the commonly used feedstocks (natural gas, CO₂, or char/biomass) and methanol production processes (from BASF-Badische Anilin und Soda Fabrik, to ICI-Imperial Chemical Industries process), as well as on membrane reactor technology utilization for generating high grade hydrogen from the catalytic conversion of methanol, reviewing the most updated state of the art in this field.

Tuning the Morphology of ZnO Nanostructures with the Ultrasonic Spray Pyrolysis Process

Nanostructured zinc oxide (ZnO) particles were synthesized by the one step Ultrasonic Spray Pyrolysis (USP) process from nitrate salt solution (Zn(NO3)2·6H2O). Various influential parameters, from Zn(NO3)2·6H2O concentrations (0.01875–0.0375 M) in the initial solution, carrier gas (N2) flow rates (0.5–0.75 L/min) to reaction temperature (400–800 °C), were tested to investigate their role on the final ZnO particles’ morphology. For this purpose, Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM) and (Selected Area Electron Diffraction) SAED techniques were used to gain insight into how the ZnO morphology is dependent on the USP process. It was revealed that, by certain parameter selection, different ZnO morphology could be achieved, from spherical to sphere-like structures assembled by interwoven nanoplate and nanoplate ZnO particles. Further, a more detailed crystallographic investigation was performed by XRD and Williamson-Hall (W-H) analysis on the ZnO with unique and non-typical planar morphology that was not reported before by USP synthesis. Moreover, for the first time, a flexible USP formation model was proposed, ending up in various ZnO morphologies rather than only ideal spheres, which is highly promising to target a wide application area.

Three-Dimensional ZnO Hierarchical Nanostructures: Solution Phase Synthesis and Applications

Zinc oxide (ZnO) nanostructures have been studied extensively in the past 20 years due to their novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three-dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future research.

Synthesis, growth mechanism, optical properties and catalytic activity of ZnO microcrystals obtained via hydrothermal processing

Herein we describe ZnO microcrystals obtainedviahydrothermal processing at 120, 150 and 180 °C, assisted by CTAB.