Comparison of Heavy Metals Removal from Aqueous Solution by Moringa oleifera Leaves and Seeds

Sorption thermodynamic and kinetic study of Cu(II) onto modified plant stem bark

In this study, four types of "Juá" stem barks (Ziziphus joazeiro) were investigated for the removal of Cu(II) from aqueous solutions. The tested samples included natural coarse barks, and barks washed with water, ethanol-water, and NaOH solutions. The solvent-modified materials simulated the waste of the industrial extraction of saponins from bark. The valorization of these processing residues as sorbents was evaluated. The NaOH-washed sorbent exhibited the highest sorption capacity for Cu(II) (maximum sorption capacity ≈ 32 mg g-1). Ion exchange process between copper and exchangeable surface cations and electrostatic attraction of copper with carboxylate and phenolate groups were identified as the primary sorption mechanisms. Desorption tests revealed that a large portion of the metal sorbed (80%) was easily released from the sorbent thus suggesting, in line with the proposed mechanisms, the existence of weak sorbate-sorbent interactions. The sorptive process was found to be exothermic (∆H° =  - 48.1 ± 13.5 kJ.mol-1) and thermodynamically favorable at lower temperatures.

Isothermal and Kinetics Modeling Approach for the Bioremediation of Potentially Toxic Trace Metal Ions Using a Novel Biosorbent Acalypha wilkesiana (Copperleaf) Leaves

The presence of trace metals in wastewater brings serious environmental pollution that threatens human health as well as the ecosystem throughout the world due to their non-biodegradability nature. The present study focuses on the bioremediation of toxic trace metals, namely arsenic (As), cadmium (Cd), and chromium (Cr), using Acalypha wilkesiana leaf raw biomass. The optimization of various process variables was done to determine the removal percentage of trace metal using Acalypha wilkesiana leaf raw biomass, and the optimum conditions were an adsorbent dose of 0.5 g, contact time 10 h, 8 h, and 10 h, process temperature 30 °C, initial concentration of trace metal as 30 µg/L, 30 mg//L, and 40 mg/L, and pH of 7.5, 7 and 7.5 for As5+, and Cd2+ and Cr6+, respectively. Acalypha wilkesiana leaf raw biomass is characterized using a scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Fourier transformation infrared spectroscopy (FTIR), zeta potential before and after adsorption of the trace metal ions. The study was well fitted for the equilibrium data for Langmuir isotherm for As5+, Cd2+, and Cr6+, Freundlich for As5+, Dubinin-Radushkevinch (D-R) for Cr6+, and Temkin for As5+ and Cr6+. The adsorption of all three trace metals was confirmed by the kinetics and thermodynamic studies to be following pseudo-second-order kinetics with endothermic as well as spontaneous processes, respectively. Thus, the present study indicates Acalypha wilkesiana leaf raw biomass as an effective and efficient novel biosorbent to remediate different trace metals from aqueous systems with its possible application in existing and novel methods for wastewater management.

Review on Moringa oleifera, a green adsorbent for contaminants removal: characterization, prediction, modelling and optimization using Response Surface Methodology (RSM) and Artificial Neural Network (ANN)

Moringa oleifera utilization in water treatment to eliminate emerging pollutants such as heavy metal ions, pesticides, pharmaceuticals, and pigments has been extensively evaluated. The efficacy of Moringa oleifera biosorbent has been investigated in diverse research work using various techniques, including its adsorption capacity kinetic, thermodynamic evaluation, adsorbent modifications, and mechanism behind the adsorption process. The Langmuir isotherm provided the most remarkable experimental data fit for batch adsorption investigations, whereas the best fit was obtained with the pseudo-second order kinetic model. Furthermore, only a few papers that combined batch adsorption with fixed-bed column investigations were examined. In the latter articles, the scientists modified the adsorbent to increase the material's adsorption capacity as determined by analytical methods, including IR spectroscopy, scanning electronic microscope (SEM), and X-ray diffraction (XRD). However, the raw material can show appreciable adsorption capacity values, proving moringa's potency as a biosorbent. Hydrogen bonds, electrostatic interaction, and van der Waals forces were the main processes in the found and reported adsorbent-adsorbate interactions. These mechanisms could change depending on the physiochemical nature of adsorption. Although frequently employed for heavy metal ions and dye adsorption, Moringa oleifera can still be explored in pesticide and medication adsorption investigations due to the few publications in this comprehensive review. This study, therefore, examined different Adsorbents from the Moringa oleifera plant, as well as parameters and models for enhancing the adsorption process.

Mesoporous Ag-functionalized magnetic activated carbon-based agro-waste for efficient removal of Pb(II), Cd(II), and microorganisms from wastewater

Herein, eco-friendly mesoporous magnetic activated carbon-based agro-waste nanosorbents incorporating antimicrobial silver nanoparticles (Mag@AC1-Ag and Mag@AC1-Ag) have been prepared. Various techniques (XRD, SEM/EDX, TEM, FTIR, and BET analysis) were employed to characterize the prepared nanosorbents before being utilized as novel nanosorbents to remove Pb+2 and Cd+2 ions. Mag@AC1-Ag and Mag@AC1-Ag exhibited rapid and excellent uptake of Pb+2 and Cd+2. The pseudo-second-order kinetics and the Langmuir isotherm are more suitable for the explanation of the experimental results. The thermodynamic parameters showed that the Pb+2 and Cd+2 sorption by the nanosorbents was a spontaneous and endothermic reaction. The prepared nanosorbents can be effectively regenerated using HCl and recycled up to the fifth cycle. These nanosorbents' potential uses for eliminating Pb+2 and Cd+2 from real water samples were evaluated. Moreover, the results revealed that both Mag@AC1-Ag and Mag@AC2-Ag exhibited high antimicrobial activity against fecal coliform (gram-negative) and Bacillus subtilis (gram-positive).

Pb(II) Ion Removal Potential in Chemically Modified Ziziphus joazeiro Barks

In this study, five types of modified Ziziphus joazeiro barks were investigated for the removal of Pb(II) ions from aqueous solutions. The samples tested were natural barks, natural powder, washed with water, ethanol at 80% (EE) and 0.5 N NaOH. Batch kinetics experiments were performed under the conditions: 24−25 °C, pH 5.5−5.8, 102 mg·L−1 Pb(NO3)2, 100 rpm and 0.1 g of adsorbent, and analyses of pHpzc and Fourier transform infrared spectroscopy. All adsorbents tested showed potential to remove Pb(II) ions, but the adsorbent washed by 0.5 N NaOH obtained the highest experimental performance (25.5 mg·g−1 at 30 min), while the EE had the least performance (20.4 mg·g−1 at 60 min), and maximum removals of 99.9%. The kinetic models pointed to a probable chemisorption due to the best fit of pseudo-second order and Elovich, and Boyd’s model, suggesting that intraparticle diffusion limits the adsorption until the initial minutes of contact. The Langmuir isotherm fitted better to the experimental data for the NaOH adsorbent, with maximum adsorption capacity equal to 62.5 mg·g−1, although the Temkin model partially fitted, both suggesting the occurrence of chemisorption. The adsorption process is reversible (>81% at 20 min) and hence the adsorbents can be recycled and the Pb(II) ions recovered.

Bioremediation of heavy metals from the aqueous environment using Artocarpus heterophyllus (jackfruit) seed as a novel biosorbent

Biosorption is an environment-friendly and economic technique to remediate heavy metals from aqueous systems. In the present study, Artocarpus heterophyllus seed powder was used as a biosorbent material to remove different heavy metals. The batch adsorption studies confirmed the higher removal percentage of the Artocarpus heterophyllus (jackfruit) seed powder for arsenic (As⁵⁺), cadmium (Cd²⁺), and chromium (Cr⁶⁺) while lower efficiency was observed for other heavy metals like copper (Cu²⁺), zinc (Zn²⁺) and nickel (Ni²⁺). Optimization of different process parameters was carried out and the optimum conditions were: adsorbent weight of 0.5 g for the initial concentration of heavy metals as 40 μg/L, 30 mg/L, and 30 mg/L; contact time of 10 h, 8 h, and 6 h; process temperature from 25 to 30 °C; pH of 7, 7.5, and 7.5 for As⁵⁺, Cd²⁺, and Cr⁶⁺ respectively. The SEM-EDX, FTIR, and XRD studies before and after adsorption of heavy metals resulted in affirmative observations. The equilibrium data of the study was well fitted for Langmuir isotherm for As⁵⁺, Cd²⁺, and Cr⁶⁺, Freundlich for As⁵⁺and Cr⁶⁺, Dubinin-Radushkevich for Cd²⁺and Cr⁶⁺. The kinetic and thermodynamic study confirmed that the adsorption of all three heavy metals was following the pseudo-second-order kinetics with the endothermic and spontaneous process respectively. The cost analysis of the process confirmed that the whole process was cost-effective compared to other processes. Hence the Artocarpus heterophyllus seed powder was verified for its high heavy metal remediation efficiency from aqueous environments along with the added advantages of being eco-friendly and economic compared to other alternatives.

Comparative removal of hazardous cationic dyes by MOF-5 and modified graphene oxide

Among cationic dyes, malachite green (MG) is commonly used for dying purposes and also as an inhibitor in aquaculture, food, health, and chemical industries due to its cytotoxic effects. Therefore, MG removal is essential to keep the ecosystem and human health safety. Adsorption is a viable and versatile option and exploring efficient adsorbents have high priority. Herein, MOF-5 and aminated corn Stover reduced graphene oxide (ACS-RGO) of typical adsorbents of metal-organic-frameworks (MOFs) and carbon-based classes were studied for MG removal. MOF-5 and ACS-RGO had a specific surface area and total pore volume of 507.4 and 389.0 m2/g, and 0.271 cm3/g and 0.273 cm3/g, respectively. ACS-RGO was superior for MG adsorption and the kinetic rate coefficient for ACS-RGO was ~ 7.2 times compared to MOF-5. For ACS-RGO, MG removal remained high (> 94%) in a wide range of pH. However, dye removal was pH-dependent for MOF-5 and increased from ~ 32% to ~ 67% by increasing pH from 4 to 12. Increasing dye concentration from 25 mg/L to 100 mg/L decreased adsorption by MOF-5 and ACS-RGO for ~ 30% and 7%, respectively. Dye removal was evident in a few tens of seconds after adding ACS-RGO at doses above 0.5 g/L. A significant loss of 46% in adsorption was observed by decreasing MOF-5 mass from 1 to 0.1 g/L. ACS-RGO removed MG in multilayer with an exceptional adsorption capacity of 1088.27 mg/g. In conclusion, ACS-RGO, and MOF-5 showed promising kinetic rates and adsorption capacities toward MG.

A critical review with emphasis on recent pieces of evidence of Moringa oleifera biosorption in water and wastewater treatment

The increasing demand for using competent and inexpensive methods based on biomaterials, like adsorption and biosorption, has given rise to the low-priced alternative biosorbents. In the past few years, Moringa oleifera (MO) has emerged as a green and low-priced biosorbent for the treatment of contaminated waters with heavy metals and dyes, and given its availability, we can create another generation of effective biosorbents based on different parts of this plant. In this review paper, we have briefed on the application of MO as a miraculous biosorbent for water purification. Moreover, the primary and cutting-edge methods for the purification and modification of MO to improve its adsorption are discussed. It was found that MO has abundant availability in the regions where it is grown, and simple chemical treatments increase the effectiveness of this plant in the treatment of some toxic contaminants. The different parts of this miraculous plant's "seeds, leaves, or even husks" in their natural form also possess appreciable sorption capacities, high efficiency for treating low metal concentrations, and rapid adsorption kinetics. Thus, the advantages and disadvantages of different parts of MO as biosorbent, the conditions favorable to this biosorption, also, the proposal of a logical mechanism, which can justify the high efficiency of this plant, are discussed in this review. Finally, several conclusions have been drawn from some important works and which are examined in this review, and future suggestions are proposed.

Mn(II) Sorption on Stream Sediments Sampled in Manganese Mining Area: Dynamics and Mechanisms

The stream sediments that have been impacted by manganese (Mn) containing wastewater for decades contain not only abundant microorganisms but also organic/inorganic substances. To achieve effective treatment of manganese (Mn)-containing effluent and recovery of Mn from water/sediments, the Mn(II) sorption behaviors and mechanism on sediments of a stream in Mn mining areas were studied. In addition, the study analyzed the effects of various factors (initial concentration, solution pH, sediment dose, contact time, and coexisting cations) on the Mn sorption efficiency of Daxin sediments, and explored the contribution of microbial activity in the sediment sorption of Mn(II). The results showed that the sorption process of Mn(II) on the sediments was consistent with the Elovich and Freundlich models, and the removal of heavy metals was maximum at 40 °C (62.47–98.93%), pH = 8 (77.51%), initial concentration of 1 mmol·L−1 (95.37%) and sediment dosing of 12 g·L−1 (98.93%). The addition of 50 mM NaN3 inhibited the microbial activity in the Daxin sediment, reducing the sorption and removal rates of Mn(II) by 0.605 mg·g−1 and 8.92%, respectively. After sorption, the proportion of the Fe–Mn oxidation(iron–manganese) state in Daxin sediments decreased from 54% to 43%, while the proportion of the exchangeable state increased by 10.80%. Microorganisms in the sediment had a positive effect on inhibiting heavy metal migration and reducing the bioavailability of contaminants in the soil. Through this study, we hope to further understand the sorption and desorption mechanism of manganese by stream sediments in manganese ore areas, so as to provide a guide on the management and recovery of Mn from stream sediments in manganese mining areas.

Pitahaya Fruit (Hylocereus spp.) Peels Evaluation for Removal of Pb(II), Cd(II), Co(II), and Ni(II) from the Waters

The present study investigated the performance of Pitahaya (Hylocereus spp.) peel (PP) as a low-cost biosorbent in the removal of Co(II), Cd(II), Pb(II), and Ni(II) from single and multi-component solutions. The characterization of the samples was carried out by pHpzc, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS). Biosorption was carried out by batch experimental procedure to examine the effects of contact time, solution pH, initial concentration of metal ions, and biosorbent dosage. The results indicate that the biosorption of Pb(II), Cd(II), Co(II), and Ni(II) Pitahaya peels followed pseudo-second-order kinetics, and equilibrium adsorption followed the Langmuir model. The maximum sorption capacities of PP for the metallic species were found to be as follows: Pb (82.64 mg g−1) > Cd (17.95 mg g−1) > Co (6.013 mg g−1) > Ni (5.322 mg g−1). However, the efficiency of the biosorption change when the metallic species are mixed. The re-generation of the PP after the adsorption of the metallic species was done using 0.1 M HNO3 solution, and the reusability of the biomass was carried out using two adsorption and desorption cycles.

Lead removal from synthetic wastewater by biosorbents prepared from seeds of Artocarpus Heterophyllus and Syzygium Cumini

The present investigation deals with removal of lead (Pb⁺²) ions from waste water using biosorbent prepared from seeds of Artocarpus heterophyllus (SBAh) and Syzygium cumini (SBSc). Biosorbents surface has been characterized through FT-IR spectroscopy to probe the presence of functional groups. Response surface methodology enabled optimized conditions (Pb⁺² concentration 2 μg/mL, pH 5.8 and bioadsorbent dose 60 mg) resulted in Pb⁺² removal ~96% for SBAh and ~93% for SBSc at agitation speed 300 rpm. The adsorption capacity has been found to be 4.93 mg/g for SBAh and 3.95 mg/g for SBSc after 70 min. At optimal experimental conditions, kinetics of biosorption was explained well by inter-particle diffusion model for SBAh (R² = 0.99) whereas Elovich model best fitted for SBSc (R² = 0.98). Further, both the biosorbents followed Temkin adsorption isotherm model.

Central Composite Design for Adsorption of Pb(II) and Zn(II) Metals on PKM-2 Moringa oleifera Leaves

Biosorption is a very effective technique to eliminate the heavy metals present in the wastewater that utilize nongrowing biomass. The adsorption ability of the Periyakulam-2 (PKM-2) variety of Moringa Oleifera leaves (MOLs) to eliminate Pb(II) and Zn(II) ions from an aqueous solution was examined in this work. Fourier transform infrared (FTIR) spectroscopy, field-emission scanning electron microscopy, energy-dispersive X-ray (EDX) analysis, X-ray powder diffraction, and Brunauer-Emmett-Teller methods were used to characterize the PKM-2 variety of MOLs. The set of variables consists of the metal ion initial concentration, a dosage of the adsorbent, and pH were optimized with the help of the response surface methodology to get maximum metal removal efficiency of lead and zinc metals using the PKM-2 MOL biosorbent. A maximum Pb(II) removal of 95.6% was obtained under the condition of initial concentration of metal ions 38 mg/L, a dosage of the adsorbent 1.5 g, and pH 4.7, and a maximum zinc removal of 89.35% was obtained under the condition of initial concentration of metal ions 70 mg/L, a dosage of the adsorbent 0.6 g, and pH 3.2. The presence of lead and zinc ions on the biosorbent surface and the functional groups involved in the adsorption process were revealed using EDX and FTIR analysis, respectively. The adsorption data were evaluated by employing different isotherm and kinetic models. Among the isotherm models, Langmuir's isotherm showed that the best fit and maximum adsorption capacities are 51.71 and 38.50 mg/g for lead and zinc, respectively. Kinetic studies showed accordance with the pseudo-second-order model to lead and zinc metal adsorption. Thermodynamic parameters confirmed (ΔG° < 0, ΔH° < 0, and ΔS° > 0) that the sorption mechanism is physisorption, exothermic, spontaneous, and favorable for adsorption. The results from this study show that the MOL of the PKM-2 type is a promising alternative for an ecofriendly, low-cost biosorbent that can effectively remove lead and zinc metals from aqueous solutions.