Recent Advances in Carbonaceous Photocatalysts with Enhanced Photocatalytic Performances: A Mini Review

Photocatalytic degradation of tetracycline using a novel WO3-ZnO/AC under visible light irradiation: Optimization of effective factors by RSM-CCD

Mitigating pharmaceutical pollution in the global environment is imperative, and tetracycline (TC) is a commonly utilized antibiotic in human and veterinary medicine. The persistent existence of TC highlights the necessity of establishing efficient measures to protect water systems and the environment from detrimental contaminants. Herein, a novel rhubarb seed waste-derived activated carbon-supported photocatalyst (WO3-ZnO/RUAC) was synthesized by combining wet impregnation and ultrasonic methods. The activated carbon (AC) was obtained from rhubarb seed waste for the first time via chemical activation. The function of AC as an electron acceptor and in separating electron-hole pairs was illuminated by characterization analyses that included XRD, FTIR, XPS, SEM, TEM, PL, EIS, TPC, and UV-DRS. Using the response surface methodology-central composite design (RSM-CCD) technique, the synthesis parameters of the composite were systematically optimized. Under ideal conditions, with a TC concentration of 33 mg. L-1, pH of 4.57, irradiation time of 108 min, and catalyst dose of 0.85 g. L-1, the highest degradation efficiency of TC by this composite, achieved 96.5%, and it was reusable for five cycles. Subsequently, trapping tests and electron spin resonance (ESR) analysis were conducted, elucidating that •OH and •O2- radicals played pivotal roles in the photocatalytic degradation of TC. This research offers valuable insights into utilizing the AC-based photocatalyst to degrade pharmaceutical micropollutants effectively.

Harnessing the photocatalytic potential of bismuth ferrite-activated carbon nanocomposite (BFO-AC) for Staphylococcus aureus decontamination under visible light

In response to the escalating global issue of microbial contamination, this study introduces a breakthrough photocatalyst: bismuth ferrite-activated carbon (BFO-AC) for visible light-driven disinfection, specifically targeting the Gram-positive bacterium Staphylococcus aureus (S. aureus). Employing an ultrasonication method, we synthesized various BFO-AC ratios and subjected them to comprehensive characterization. Remarkably, the bismuth ferrite-activated carbon 1:1.5 ratio (BA 1:1.5) nanocomposite exhibited the narrowest band gap of 1.86 eV. Notably, BA (1:1.5) demonstrated an exceptional BET surface area of 862.99 m2/g, a remarkable improvement compared to pristine BFO with only 27.61 m2/g. Further investigation through FE-SEM unveiled the presence of BFO nanoparticles on the activated carbon surface. Crucially, the photocatalytic efficacy of BA (1:1.5) towards S. aureus reached its zenith, achieving complete inactivation in just 60 min. TEM analysis revealed severe damage and rupture of bacterial cells, affirming the potent disinfection capabilities of BA (1:1.5). This exceptional disinfection efficiency underscores the promising potential of BA (1:1.5) for the treatment of contaminated water sources. Importantly, our results underscore the enhanced photocatalytic performance with an increased content of activated carbon, suggesting a promising avenue for more effective microorganism inactivation.

Untangling the Effect of Carbonaceous Materials on the Photoelectrochemical Performance of BaTaO2N

The water oxidation reaction is a rate-determining step in solar water splitting. The number of surviving photoexcited holes is one of the most influencing factors affecting the photoelectrochemical water oxidation efficiency of photocatalysts. The solar-to-hydrogen energy conversion efficiency of BaTaO2N is still far below the benchmark efficiency set for practical applications, notwithstanding its potential as a 600 nm-class photocatalyst in solar water splitting. To improve its efficiency in photoelectrochemical water splitting, this study offers a straightforward route to develop photocatalytic materials based on the combination of BaTaO2N and carbonaceous materials with different dimensions. The impact of diverse carbonaceous materials, such as fullerene, g-C3N4, graphene, carbon nanohorns, and carbon nanotubes, on the photoelectrochemical behavior of BaTaO2N has been examined. Notably, the use of graphene and g-C3N4 remarkably improves the photoelectrochemical performance of the composite photocatalysts through a higher photocurrent and acting as electron reservoirs. Consequently, a marked reduction in recombination rates, even at low overpotentials, leads to a higher accumulation of photoexcited holes, resulting in 2.6- and 1.7-fold increased BaTaO2N photocurrent densities using graphene and g-C3N4, respectively. The observed trends in the dark for the oxygen reduction reaction (ORR) potential align with the increase in the photocurrent density, revealing a good correlation between opposite phenomena. Importantly, the enhancement observed implies an underlying accumulation phenomenon. The verification of this concept lies in the evidence provided by oxygen reduction and is in line with photoredox flux matching during photocatalysis. This research underscores the intricate interplay between carbonaceous materials and oxynitride photocatalysts, offering a strategic approach to enhancing various photocatalytic capabilities.

Covalently linked pyrene antennas for optically dense yet aggregation-resistant light-harvesting systems

In this study we present a novel energy transfer material inspired by natural light-harvesting antenna arrays, zinc(II) phthalocyanine-pyrene (ZnPcPy). The ZnPcPy system facilitates energy transfer from 16 covalently linked pyrene (Py) donor chromophores to the emissive central zinc(II) phthalocyanine (ZnPc) core. Nearly 98% energy transfer efficiency is determined from the changes in emission decay rates between free MePy to covalently linked Py, supported by comparisons of photoluminescence quantum yields using different excitation wavelengths. A comparative analysis of ZnPcPy and an equivalent mixture of ZnPc and MePy demonstrates the superior light-harvesting performance of the covalently linked system, with energy transfer rates 9705 times higher in the covalently bound system. This covalent strategy allows for very high loadings of absorbing Py chromophores to be achieved while also avoiding exciton quenching that would otherwise arise, with the same strategy widely applicable to other pairs of Főrster resonance energy transfer (FRET) chromophores.

Rational optimization of g-C3N4/Co3O4 nanocomposite for enhanced photodegradation of Rhodamine B dye under visible light

Heterogeneous catalysis is widely known as an efficient, clean, and low-cost technology to mitigate the environmental pollution of industrial effluents. This research aimed at optimizing the preparation and characterization of efficient g-C₃N₄/Co₃O₄ nanocomposite for catalytic removal of Rhodamine B (Rh B) dye. The detected XRD peaks for the prepared nano-Co₃O₄ are matched with the cubic crystal structure. In contrast, the broad peak at 27.3° corresponding to the graphite reflection of hkl (002) was noticeably weakened in the XRD pattern of the g-C₃N₄/Co₃O₄ composite. FTIR spectra of g-C₃N₄/Co₃O₄ nanocomposites revealed the active vibrational modes of each Co₃O₄ and g-C₃N₄ component. The microstructure study of g-C₃N₄ showed the strong interlayer stacking of carbon nitride nanosheets, while the surface morphology of g-C₃N₄/Co₃O₄ nanocomposite revealed a hybrid particulate system. EDS analysis indicated that the spot area of g-C₃N₄/Co₃O₄ confirmed the chemical ratios of carbon, nitrogen, cobalt, and oxygen. BET measurements of g-C₃N₄/Co₃O₄ showed a significant increase in the surface area and pore volume of single components due to the lamination of stacked g-C₃N₄ nanosheets by the intercalated Co₃O₄ nanoparticles. The prepared 30% g-C₃N₄/Co₃O₄ revealed the lowest value of E_g ~1.2 eV and the highest light absorptivity suggesting strong promotion for the photocatalytic performance under visible light. The maximum photocatalytic activity of about 87% was achieved by 30% g-C₃N₄/Co₃O₄ due to the photonic enhancement, which reduces the recombination of excited electrons. The developed nanocomposite with a g-C₃N₄/Co₃O₄ ratio of 0.3 exhibited high stability in its photocatalytic performance after four recycling times, and a slight decrease of about 7% was estimated after the 5th reuse test.

Immobilization of photocatalytic materials for (waste)water treatment using 3D printing technology - advances and challenges

Photocatalysis has been considered a promising technology for the elimination of a wide range of pollutants in water. Various types of photocatalysts (i.e., homojunction, heterojunction, dual Z-scheme photocatalyst) have been developed in recent years to address the drawbacks of conventional photocatalysts, such as the large energy band gap and rapid recombination rate of photogenerated electrons and holes. However, there are still challenges in the design of photocatalytic reactors that limit their wider application for real (waste)water treatment, such as difficulties in their recovery and reuse from treated (waste)waters. 3D printing technologies have been introduced very recently for the immobilization of materials in novel photocatalytic reactor designs. The present review aims to summarize and discuss the advances and challenges in the application of various 3D printing technologies (i.e., stereolithography, inkjet printing, and direct ink writing) for the fabrication of stable photocatalytic materials for (waste)water treatment purposes. Furthermore, the limitations in the implementation of these technologies to design future generations of photocatalytic reactors have been critically discussed, and recommendations for future studies have been presented.

Kraft lignin-based carbon xerogel/zinc oxide composite for 4-chlorophenol solar-light photocatalytic degradation: effect of pH, salinity, and simultaneous Cr(VI) reduction

Considering the ever-increasing need for efficient wastewater treatment, this study focused on the development of new kraft lignin-based carbon xerogel/zinc oxide (XCL/ZnO w) photocatalysts. The inclusion of the carbon xerogel is expected to cause an improvement in charge transfer throughout the photoactivation process, consequently enhancing its overall photocatalytic efficiency. Characterization shows that the materials developed are composed of both zinc oxide and carbon xerogel. The addition of the lignin-based carbon xerogel caused a significant morphological modification to the composite materials, resulting in a greater specific surface area. Regarding the photocatalytic efficiency, the optimized composite (XCL/ZnO 1.0) displayed superior efficiency to the pure zinc oxide, especially when calcined at 700 °C, with an increase of 20% in the overall photodegradation capacity for the 4-chlorophenol (4CP) molecule. The XCL/ZnO 1.0 also displayed better performance than its tannin counterpart, previously reported in the literature, obtaining a 60% increase in the apparent reaction rate constant. The XCL/ZnO 1.0 also displayed better performance for the simultaneous hexavalent chrome (Cr (VI)) reduction/4CP oxidation reaction. Salinity and system pH had a significant influence on the efficiency of the 4CP photodegradation, as higher values of salinity and lower pHs caused a decrease in the overall efficiency of the process. At last, chronoamperometry and open-circuit potential tests confirmed the superiority of the XCL/ZnO 1.0 over the pure ZnO, highlighting the beneficial impact of the carbon xerogel on the charge transport dynamics of the composite.

Wastewater treatment with nanomaterials for the future: A state-of-the-art review

Aquatic and terrestrial ecosystems are both threatened by toxic wastewater. The unique properties of nanomaterials are currently being studied thoroughly for treating sewage. Nanomaterials also have the advantage of being capable of removing organic matter, fungi, and viruses from wastewater. Advanced oxidation processes are used in nanomaterials to treat wastewater. Additionally, nanomaterials have a large effective area of contact due to their tiny dimensions. The adsorption and reactivity of nanomaterials are strong. Wastewater treatment would benefit from the development of nanomaterial technology. Second, the paper provides a comprehensive analysis of the unique characteristics of nanomaterials in wastewater treatment, their proper use, and their prospects. In addition to focusing on their economic feasibility, since limited forms of nanomaterials have been manufactured, it is also necessary to consider their feasibility in terms of their technical results. According to this study, the significant adsorption area, excellent chemical reaction, and electrical conductivity of nanoparticles (NPs) contribute to the successful treatment of wastewater.

Bioenergy Generation and Wastewater Purification with Li0.95Ta0.76Nb0.19Mg0.15O3 as New Air-Photocathode for MFCs

MFC is a promising technology that can be used for simultaneous electricity generation and wastewater treatment. Power energy generation of a ferroelectric cathodic ceramic, Li0.95Ta0.76Nb0.19Mg0.15O3 (LTNMg), has been measured in microbial fuel cells, integrating a single chamber fed by industrial wastewater (CODinitial = 471 mg L−1, and pHinitial = 7.24 at T = 27 °C). In this process, the mixed multicomponent oxide material has been prepared and characterized by XRD, PSD, TEM, and UV-Vis spectroscopy. The catalytic activity has been investigated by COD determination, analysis of heavy metals, and polarization measurement. The results show a high COD reduction efficiency, which reaches 95.70% after a working time of 168 h with a maximal power density of 228 mW m−2. In addition, the maximum value of generated voltage in the open-circuit potential (OCP) of this MFC configuration has been increased from 340 mV in the absence of a light source to 470 mV under irradiation, indicating the presence of a promoting photocatalytic effect of LTNMg, which improved the process of the cathodic electron transfer inside the MFC device.

Volatile organic compounds (VOCs) removal by photocatalysts: A review

Amplified anthropogenic release of volatile organic compounds (VOCs) gets worse air quality and human health. Photocatalytic degradation of VOCs is the practical strategy due to its low cost, simplicity, high efficiency, and environmental sustainability. Different types of photocatalyst activated by UV and visible lights are applied for VOC degradation. This review tries to investigate the state-of-art of recently published papers on this subject with a focus on the high-efficiency photocatalyst. The novel photocatalysts are introduced and enhancing photocatalytic activity strategies such as the hybrid of two/three photocatalyst, impurity doping, and heterojunctions with narrow bandgap semiconductors have been explained. The procedures of visible light activation of the photocatalysts are discussed with attention to current problems and future challenges. In addition, effective operational parameters in the photocatalytic degradation of VOCs have been reviewed with their advantages and drawbacks. A series of strategies are developed for the efficient utilization of visible light photocatalysts and improving new materials or design structures to degrade produced toxic intermediates/by-products during photocatalytic degradation of VOCs. This review shows that there are significant challenges in the applications of photocatalysts in the selective removal of VOCs. Several approaches should be combined to produce synergistic effects, which may lead to much higher photocatalytic performance than individual strategies. Another challenge is to develop efficient photocatalysts to meet real problems on an industrial scale.

Photocatalytic Degradation of Orange G Dye by Using Bismuth Molybdate: Photocatalysis Optimization and Modeling via Definitive Screening Designs

In the current study, Bismuth molybdate was synthesized using simple co-precipitation procedure, and their characterization was carried out by various methods such as FT-IR, SEM, and P-XRD. Furthermore, the photocatalytic degradation of Orange G (ORG) dye using synthesized catalyst under visible light irradiation was studied. Response surface Method was used for the optimization of process variables and degradation kinetics evaluated by modeling of experimental data. Based on the experimental design outcomes, the first-order model was proven as a practical correlation between selected factors and response. Further ANOVA analysis has revealed that only two out of six factors have a significant effect on ORG degradation, however ORG concentration and irradiation time indicated the significant effects sequentially. Maximum ORG degradation of approximately 96% was achieved by keeping process parameters in range, such as 1 g L-1 loading of catalyst, 50 mg L-1 concentration of ORG, 1.4 mol L-1 concentration of H2O2 at pH 7 and a temperature of 30 °C. Kinetics of ORG degradation followed the pseudo first order, and almost complete degradation was achieved within 8 h. The effectiveness of the Bi2MoO6/H2O2 photo-Fenton system in degradation reactions is due to the higher number of photo-generated e- available on the catalyst surface as a result of their ability to inhibit recombination of e- and h+ pair.

Reduced graphene oxide–zinc sulfide (RGO–ZnS) nanocomposite: a new photocatalyst for oxidative cyclization of benzylamines to benzazoles under visible-light irradiation

A simple route for the preparation of a reduced graphene oxide–zinc sulfide (RGO–ZnS) nanocomposite via one-pot hydrothermal synthesis has been reported.

Visible Light Trapping against Charge Recombination in FeOx-TiO2 Photonic Crystal Photocatalysts

Tailoring metal oxide photocatalysts in the form of heterostructured photonic crystals has spurred particular interest as an advanced route to simultaneously improve harnessing of solar light and charge separation relying on the combined effect of light trapping by macroporous periodic structures and compositional materials' modifications. In this work, surface deposition of FeOx nanoclusters on TiO2 photonic crystals is investigated to explore the interplay of slow-photon amplification, visible light absorption, and charge separation in FeOx-TiO2 photocatalytic films. Photonic bandgap engineered TiO2 inverse opals deposited by the convective evaporation-induced co-assembly method were surface modified by successive chemisorption-calcination cycles using Fe(III) acetylacetonate, which allowed the controlled variation of FeOx loading on the photonic films. Low amounts of FeOx nanoclusters on the TiO2 inverse opals resulted in diameter-selective improvements of photocatalytic performance on salicylic acid degradation and photocurrent density under visible light, surpassing similarly modified P25 films. The observed enhancement was related to the combination of optimal light trapping and charge separation induced by the FeOx-TiO2 interfacial coupling. However, an increase of the FeOx loading resulted in severe performance deterioration, particularly prominent under UV-Vis light, attributed to persistent surface recombination via diverse defect d-states.

Enhanced removal efficiency of toluene over activated carbon under visible light

Toluene removal rates using activated carbon (AC) at various relative humidity (RH) levels (0%, 30%, 60%) were compared under dark and visible-light conditions. Light exposure significantly increased toluene-removal efficiency independent of RH. When AC was pre-treated with an optimal concentration of HNO₃, its toluene-removal efficiency was enhanced further with light, an effect that can be attributed to increased surface-area and porosity. Fourier-transform infrared analysis confirmed that exposure of HNO₃-modified AC to light induced partial oxidation of toluene. Within visible-light range (380-650 nm), shorter wavelengths were more effective for toluene-removal compared with longer wavelengths. This suggests that hydroxyl groups formed on AC-surface under light strongly interact with aromatic rings of toluene, allowing for greater uptake of toluene. Moreover, AC can sustain its photo-activity when mixed with cement and cured, suggesting its potential applications in air-purifying building materials. An efficient and practical method for regeneration of spent AC is also demonstrated.

Wastewater treatment nexus: Carbon nanomaterials towards potential aquatic ecotoxicity

Carbon nanomaterials (CNMs) provide an effective solution and a novel advancement for wastewater treatment. In this review, a total of 3823 bibliographic records derived from recent 10 years are visualized based on scientometric analysis. The results indicate metal-free CNMs-mediated advanced oxidation processes (AOPs) might be a motive force to develop CNMs application for wastewater treatment; however, corresponding evaluations of aquatic toxicity still lack sufficient attention. Therefore, recent breakthroughs and topical innovations related to prevalent wastewater treatment technologies (i.e., adsorption, catalysis and membrane separation) using three typical dimensional CNMs (nanodiamonds, carbon nanotubes, and graphene-based nanomaterials) are comprehensively summarized in-depth, along with a compendious introduction to some novel techniques (e.g., computational simulation) for identifying reaction mechanisms. Then, current research focusing on CNMs-associated aquatic toxicity is discussed thoroughly, mainly demonstrating: (1) the adverse effects on aquatic organisms should not be overlooked prior to large-scale CNMs application; (2) divergent consequences can be further reduced if the ecological niche of aquatic organisms is emphasized; and (3) further investigations on joint toxicity can provide greater beneficial insight into realistic exposure scenarios. Finally, ongoing challenges and developmental directions of CNMs-based wastewater treatment and evaluation of its aquatic toxicity are pinpointed and shaped in terms of future research.

Red Emission Carbon Dots Prepared by 1,4-Diaminonaphthalene for Light-Emitting Diode Application and Metal Ion Detection

Carbon dots (CDs), as the most important type of carbon materials, have been widely used in many fields because of their unique fluorescence characteristics and excellent properties of biocompatibility. In previous studies, the fluorescence of CDs was mainly concentrated in the blue and green, whereas the red fluorescence was relatively less. Herein, we prepared efficient red-emitting CDs from 1,4-diaminonaphthalene using solvothermal methods. We discussed the effects of different solvothermal solvents on CDs. The results show that CDs prepared with octane and acetone as reaction media have the best fluorescence properties. The CDs dispersed in different organic solvents exhibited tunable emission across a wide spectrum from 427 nm to 679 nm. We further demonstrated the application of red light-emitting diode (LED) optoelectronics and fluorescence detection of Fe3+ in aqueous solution.

Photochemical reactivity of nitrogen-doped biochars under simulated sunlight irradiation: Generation of singlet oxygen

This study explored the photochemical activity of nitrogen-doped biochars (NCMs) by investigating their role in the degradation of sulfamethazine under simulated sunlight irradiation. NCMs with different doping amounts were prepared from corn straw and urea. Results showed that nitrogen doping can notably enhance the photodegradation of SMT rather than raw char. NCMs are of photochemical activity under visible light, which was confirmed by monochromatic light experiments. Quenching experiments, ESR, pH effect, and the influence of O₂ were carried out to explore the involved oxidation mechanism in this system. Results showed that ¹O₂ was the main reactive oxygen species. ¹O₂ was produced from O₂ by both energy transfer and electron transfer. DFT calculations showed that pyridinic N doping can decrease the energy of intersystem crossing and thus benefit the generation of ¹O₂ by triplet-triplet energy transfer. Results underscore the explicit importance of nitrogen element in photochemical reactivity of chars under simulated light irradiation even when the nitrogen content is low. It is a meaningful reminder for us to pay more attention to the assessment of the fate and transport of contaminants in the soil where it is rich in NCMs as well as the potential use of NCMs for pollutants remediation, since visible light is very abundant near the earth's surface.

Photocatalytic Degradation of Methylene Blue Using Zinc Oxide Nanorods Grown on Activated Carbon Fibers

In this work, the synthesis, characterization, and photocatalytic performance of zinc oxide/activated carbon fiber nanocomposites prepared by hydrothermal method were investigated. Zinc oxide nanoparticles (ZnO-NP) were deposited as seeds on porous activated carbon fiber (ACF) substrates. Then, zinc oxide nanorods (ZnO-NR) were successfully grown on the seeds and assembled on the fibers’ surface in various patterns to form ZnO-NR/ACF nanocomposites. The nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectrometry, UV–vis diffuse reflectance spectra (DRS), and Brunauer–Emmett–Teller (BET) surface area analysis. SEM images showed that brush-like and flower-like ZnO-NR patterns were grown uniformly on the ACF surface with sizes depending on the ZnO-NP concentration, growth time, and temperature. The FTIR spectrum confirmed the presence of the major vibration bands, especially the absorption peaks representing the vibration modes of the COOH (C = O and C = C) functional group. Adsorption and photocatalytic activities of the synthesized catalytic adsorbents were compared using methylene blue (MB) as the model pollutant under UV irradiation. ZnO-NR/ACF nanocomposites showed excellent photocatalytic activity (~99% degradation of MB in 2 h) compared with that of bare ZnO-NR and ACF. Additionally, a recycling experiment demonstrated the stability of the catalyst; the catalytic degradation ratio of ZnO-NR/ACF reached more than 90% after five successive runs and possessed strong adsorption capacity and high photocatalytic ability. The enhanced photocatalytic activities may be related to the effects of the relatively high surface area, enhanced UV-light absorption, and decrease of charge carrier recombination resulting from the synergetic adsorption–photocatalytic degradation effect of ZnO and ACF.

Flow Photochemistry as a Tool in Organic Synthesis

Photochemical transformations of molecular building blocks have become an important and widely recognized research field in the past decade. Detailed and deep understanding of novel photochemical catalysts and reaction concepts with visible light as the energy source has enabled a broad application portfolio for synthetic organic chemistry. In parallel, continuous-flow chemistry and microreaction technology have become the basis for thinking and doing chemistry in a novel fashion with clear focus on improved process control for higher conversion and selectivity. As can be seen by the large number of scientific publications on flow photochemistry in the recent past, both research topics have found each other as exceptionally well-suited counterparts with high synergy by combining chemistry and technology. This review will give an overview on selected reaction classes, which represent important photochemical transformations in synthetic organic chemistry, and which benefit from mild and defined process conditions by the transfer from batch to continuous-flow mode.

Decoration of Zinc Oxide Nanorods into the Surface of Activated Carbon Obtained from Agricultural Waste for Effective Removal of Methylene Blue Dye

Zinc oxide (ZnO) nanorods incorporated activated carbon (AC) composite photocatalyst was synthesized using a hydrothermal process. The AC was prepared from lapsi (Choerospondias axillaris) seed stone, an agricultural waste product, found in Nepal by the chemical activation method. An aqueous suspension of AC with ZnO precursor was subjected to the hydrothermal treatment at 140 °C for 2 h to decorate ZnO rods into the surface of AC. As-obtained ZnO nanorods decorated activated carbon (ZnO/AC) photocatalyst was characterized by various techniques, such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoluminescence (PL) spectroscopy. Results showed that highly crystalline hexagonal ZnO nanorods were effectively grown on the surface of porous AC. The photocatalytic property of the as-prepared ZnO/AC composite was studied by degrading methylene blue (MB) dye under UV-light irradiation. The ZnO/AC composite showed better photocatalytic property than that of the pristine ZnO nanorods. The enhanced photocatalytic performance in the case of the ZnO/AC composite is attributed to the combined effects of ZnO nanorods and AC.

Carbon-based nanomaterials: in the quest of alternative metal-free photocatalysts for solar water splitting

One of the alarming problems of modern civilization is global warming due to the inevitable rise of CO2 in the environment, mainly because of the excessive use of traditional fossil fuels. The gradual depletion of fossil fuels is another challenge regarding the future energy demand; therefore, alternative renewable energy research is necessary. One of the alternative approaches is the solar fuel generation by means of photocatalytic water splitting and more specifically, hydrogen evolution from water through the reductive half-reaction. Hydrogen is the cleanest fuel and does not produce any greenhouse gas upon direct combustion, or even while acting as a chemical feedstock for other transportable fuel generation. Therefore, it is desirable to produce efficient photocatalysts for solar water splitting. After the discovery of the first photocatalytic water splitting reaction by Fujisima and Honda, several advancements have been made with metal-based inorganic semiconductor photo-catalysts. However, their practical applicability is still under debate considering the environmental sustainability, stability and economical expenses. As a result, it is essential to develop alternate photocatalysts that are environmentally sustainable, cost-effective, stable and highly efficient. The metal-free approach is one of the most promising approaches in this regard. Herein, we discuss the recent developments in carbon-based materials and their hybrids as alternative metal free photocatalysts for solar water splitting. The present discussion includes g-C3N4, two-dimensional graphene/graphene oxides, one-dimensional carbon nanotubes/carbon nanofibers and zero-dimensional graphene QDs/carbon dots. We have focused on the rectification of exciton generation, charge separation and interfacial photochemical processes for photocatalysis, followed by possible optimization pathways of these typical all carbon-based materials. Finally, we have highlighted several fundamental challenges and their possible solutions, as well as the future direction on this particular aspect.

Recent Progress, Challenges, and Prospects in Two-Dimensional Photo-Catalyst Materials and Environmental Remediation

The successful photo-catalyst library gives significant information on feature that affects photo-catalytic performance and proposes new materials. Competency is considerably significant to form multi-functional photo-catalysts with flexible characteristics. Since recently, two-dimensional materials (2DMs) gained much attention from researchers, due to their unique thickness-dependent uses, mainly for photo-catalytic, outstanding chemical and physical properties. Photo-catalytic water splitting and hydrogen (H2) evolution by plentiful compounds as electron (e-) donors is estimated to participate in constructing clean method for solar H2-formation. Heterogeneous photo-catalysis received much research attention caused by their applications to tackle numerous energy and environmental issues. This broad review explains progress regarding 2DMs, significance in structure, and catalytic results. We will discuss in detail current progresses of approaches for adjusting 2DMs-based photo-catalysts to assess their photo-activity including doping, hetero-structure scheme, and functional formation assembly. Suggested plans, e.g., doping and sensitization of semiconducting 2DMs, increasing electrical conductance, improving catalytic active sites, strengthening interface coupling in semiconductors (SCs) 2DMs, forming nano-structures, building multi-junction nano-composites, increasing photo-stability of SCs, and using combined results of adapted approaches, are summed up. Hence, to further improve 2DMs photo-catalyst properties, hetero-structure design-based 2DMs' photo-catalyst basic mechanism is also reviewed.

Recent Progress on Fullerene-Based Materials: Synthesis, Properties, Modifications, and Photocatalytic Applications

Solar light is an inexpensive energy source making up for energy shortage and solving serious environmental problems. For efficient utilization of solar energy, photocatalytic materials have attracted extensive attention over the last decades. As zero-dimensional carbon nanomaterials, fullerenes (C60, C70, etc.) have been extensively investigated for photocatalytic applications. Due to their unique properties, fullerenes can be used with other semiconductors as photocatalyst enhancers, and also as novel photocatalysts after being dispersed on non-semiconductors. This review summarizes fullerene-based materials (including fullerene/semiconductors and fullerene/non-semiconductors) for photocatalytic applications, such as water splitting, Cr (Ⅵ) reduction, pollutant degradation and bacterial disinfection. Firstly, the optical and electronic properties of fullerene are presented. Then, recent advances in the synthesis and photocatalytic mechanisms of fullerene-based photocatalysts are summarized. Furthermore, the effective performances of fullerene-based photocatalysts are discussed, mainly concerning photocatalytic H2 generation and pollutant removal. Finally, the current challenges and prospects of fullerene-based photocatalysts are proposed. It is expected that this review could bring a better understanding of fullerene-based photocatalysts for water treatment and environmental protection.

Recent progress on the enhancement of photocatalytic properties of BiPO4 using π-conjugated materials

Semiconductor photocatalysis is regarded as most privileged solution for energy conversion and environmental application. Recently, photocatalysis methods using bismuth-based photocatalysts, such as BiPO₄, have been extensively investigated owing to their superior efficacy regarding organic pollutant degradation and their further mineralization into CO₂ and H₂O. It is well known that BiPO₄ monoclinic phase exhibited better photocatalytic performance compared to Degussa (Evonik) P25 TiO₂ in term of ultraviolet light driven organic pollutants degradation. However, its wide band gap, poor adsorptive performance and large size make BiPO₄ less active under visible light irradiation. However, extensive research works have been conducted in the past with the aim of improving visible light driven BiPO₄ activity by constructing a series of heterostructures, mainly coupled with π-conjugated architecture (e.g., conductive polymer, dye sensitization and carbonaceous materials). However, a critical review of modified BiPO₄ systems using π-conjugated materials has not been published to date. Therefore, this current review article was designed with the aim of presenting a brief current state-of-the-art towards synthesis methods of BiPO₄ in the first section, with an especial focuses onto its crystal-microstructure, optical and photocatalytic properties. Moreover, the most relevant strategies that have been employed to improve its photocatalytic activities are then addressed as the main part of this review. Finally, the last section presents ongoing challenges and perspectives for modified BiPO₄ systems using π-conjugated materials.

Superior decontamination of toxic organic pollutants under solar light by reduced graphene oxide incorporated tetrapods-like Ag3PO4/MnFe2O4 hierarchical composites

To fabricate an efficient, eco-friendly and stable photocatalyst, the current work describes a demonstration of simple synthesis approach of Ag₃PO₄/MnFe₂O₄(x wt%)/reduced graphene oxide composites. Ag₃PO₄/MnFe₂O₄ (5 wt%) revealed superior activity for decontamination of dye pollutant. Further, rGO was incorporated with Ag₃PO₄/MnFe₂O₄ (5 wt%) to investigate its effect on their overall properties. The resultant composites were characterized by various analytical techniques to confirm their structural and physical-chemical features. FESEM analysis showed that morphology of Ag₃PO₄ varied significantly from orthorhombic dodecahedrons to tripods and tetrapods with the combinations MnFe₂O₄ (5 wt%), and MnFe₂O₄ (5 wt%)+rGO respectively. The photocatalytic decontamination of toxic organic dyes tested against Rhodamine B(RhB) and 4-Nitrophenol. The outstanding performance for decontamination of RhB was observed for Ag₃PO₄/MnFe₂O₄(5 wt%)/rGO (~99% in 5 min) with the rate of k = 7.28 × 10^-1 min^-1. The enhanced activity of Ag₃PO₄/MnFe₂O₄(5 wt%)/rGO composites credited to co-catalytic effects of MnFe₂O₄ and physiochemical properties of rGO which leads to making intimate contact with Ag₃PO₄ to form heterojunction and rGO served as a medium for charge transfer to prevent their recombination. The incorporation of rGO in Ag₃PO₄/MnFe₂O₄ (5 wt%) composite leads to a considerable increase in the photocatalytic activity by offering improved surface area and properties, high electron stability and mobility. Based on experiment results, the photocatalytic enhancement mechanism for organic pollutants degradation was discussed. The recyclability of Ag₃PO₄/MnFe₂O₄(5 wt%)/rGO hierarchical composite was evaluated by replicated photocatalytic reaction trials. Overall, the morphological transformation of Ag₃PO₄/MnFe₂O₄(5 wt%)/rGO composites played a dynamic role in determining their photocatalytic activity towards the organic industrial dye pollutants.

Degradation of antibiotics by advanced oxidation processes: An overview

Antibiotics are becoming emerging contaminants due to their extensive production and consumption, which have caused hazards to the ecological environment and human health. Various techniques have been studied to remove antibiotics from water and wastewater, including biological, physical and chemical methods. Among them, advanced oxidation processes (AOPs) have received increasing attention due to their fast reaction rate and strong oxidation capability, which are effective for the degradation of antibiotics in aquatic environments. In this review paper, a variety of AOPs, such as Fenton or Fenton-like reaction, ozonation or catalytic ozonation, photocatalytic oxidation, electrochemical oxidation, and ionizing radiation were briefly introduced, including their principles, characteristics, main influencing factors and applications. The current applications of AOPs for the degradation of antibiotics in water and wastewater were analyzed and summarized, the concluding remarks were given and their future perspectives and challenges were discussed.

Photosensitive Hybrid Nanostructured Materials: The Big Challenges for Sunlight Capture

Solar radiation is becoming increasingly appreciated because of its influence on living matter and the feasibility of its application for a variety of purposes. It is an available and everlasting natural source of energy, rapidly gaining ground as a supplement and alternative to the nonrenewable energy feedstock. Actually, an increasing interest is involved in the development of efficient materials as the core of photocatalytic and photothermal processes, allowing solar energy harvesting and conversion for many technological applications, including hydrogen production, CO2 reduction, pollutants degradation, as well as organic syntheses. Particularly, photosensitive nanostructured hybrid materials synthesized coupling inorganic semiconductors with organic compounds, and polymers or carbon-based materials are attracting ever-growing research attention since their peculiar properties overcome several limitations of photocatalytic semiconductors through different approaches, including dye or charge transfer complex sensitization and heterostructures formation. The aim of this review was to describe the most promising recent advances in the field of hybrid nanostructured materials for sunlight capture and solar energy exploitation by photocatalytic processes. Beside diverse materials based on metal oxide semiconductors, emerging photoactive systems, such as metal-organic frameworks (MOFs) and hybrid perovskites, were discussed. Finally, future research opportunities and challenges associated with the design and development of highly efficient and cost-effective photosensitive nanomaterials for technological claims were outlined.

Green Synthesis of Composite Graphene Aerogels with Robust Magnetism for Effective Water Remediation

Graphene-based three-dimensional (3D) magnetic assemblies have attracted great research attention owing to their multiple natures inherited from 3D graphene assemblies and magnetic materials. However, at present, the practical applications of graphene-based magnetic materials are limited by the relative complex synthesis procedure and harsh operation conditions. Hence, a facile and green synthesis strategy is highly desired. Herein, a magnetic graphene aerogel with magnetite nanoparticles in-situ synthesized on the surface of its frameworks was fabricated through a green and facile strategy. The synthesis process was performed in a gentle condition with low energy consumption. The obtained graphene aerogels exhibited superior magnetism with a saturation magnetization of 55.7 emu·g-1. With the merits of well-developed pore structures, high surface area, and robust magnetic property, the obtained composite aerogels exhibited intriguing adsorption and photo-Fenton catalytic degradation performances for the organic dyes in water. Moreover, the utilized graphene aerogels could be recycled from the water due to their effective magnetic separation performance, indicating a promising capability for practical applications in the area of water remediation. We anticipate this synthesis strategy could provide some guidance for the design and development of 3D magnetic assemblies.