Facile Preparative Access to Bioactive Silicon Oxycarbides with Tunable Porosity

Polymer-Derived Biosilicate®-like Glass-Ceramics: Engineering of Formulations and Additive Manufacturing of Three-Dimensional Scaffolds

Silicone resins, filled with phosphates and other oxide fillers, yield upon firing in air at 1100 °C, a product resembling Biosilicate^® glass-ceramics, one of the most promising systems for tissue engineering applications. The process requires no preliminary synthesis of parent glass, and the polymer route enables the application of direct ink writing (DIW) of silicone-based mixtures, for the manufacturing of reticulated scaffolds at room temperature. The thermal treatment is later applied for the conversion into ceramic scaffolds. The present paper further elucidates the flexibility of the approach. Changes in the reference silicone and firing atmosphere (from air to nitrogen) were studied to obtain functional composite biomaterials featuring a carbon phase embedded in a Biosilicate^®-like matrix. The microstructure was further modified either through a controlled gas release at a low temperature, or by the revision of the adopted additive manufacturing technology (from DIW to digital light processing).

Macromonomers as a Novel Way to Investigate and Tailor Silicon-Oxycarbide-Based Materials Obtained from Polymeric Preceramic Precursors

It has been shown that bifunctional monomers (D units), which are used to increase the carbon content in silicon oxycarbide precursors, can form volatile oligomers, thus affecting the amount of carbon available during the transition into the final material in the annealing process. Additionally, an uneven distribution of carbon-rich mers may lead to the formation of a free-carbon phase, instead of the incorporation of carbon atoms into the silicon matrix. In this study, a novel two-step approach was utilized. Firstly, a macromonomer containing a number of structural units with precise structure was synthesized, which was later polycondensed into a ceramic precursor. Chlorodimethylsilane modified 2,4,6,8-tetramethylcyclotetrasiloxane was used as a silicon oxycarbide precursor monomer containing both T and D structural units (i.e., silicon atoms bonded to three and two oxygen atoms, respectively), with well-defined interconnections between structural units. Such a macromonomer prevents the formation of small siloxane rings, and has a very limited number of possible combinations of structural units neighboring each silicon atom. This, after investigation using IR, XRD, TG and elemental analysis, gave insight into the effect of “anchoring” silicon atoms bonded to two methyl groups, as well as the impact of their distribution in comparison to the materials obtained using simple monomers containing a single silicon atom (structural unit).

Effect of the Content and Ordering of the sp2 Free Carbon Phase on the Charge Carrier Transport in Polymer-Derived Silicon Oxycarbides

The present work elaborates on the correlation between the amount and ordering of the free carbon phase in silicon oxycarbides and their charge carrier transport behavior. Thus, silicon oxycarbides possessing free carbon contents from 0 to ca. 58 vol.% (SiOC/C) were synthesized and exposed to temperatures from 1100 to 1800 °C. The prepared samples were extensively analyzed concerning the thermal evolution of the sp2 carbon phase by means of Raman spectroscopy. Additionally, electrical conductivity and Hall measurements were performed and correlated with the structural information obtained from the Raman spectroscopic investigation. It is shown that the percolation threshold in SiOC/C samples depends on the temperature of their thermal treatment, varying from ca. 20 vol.% in the samples prepared at 1100 °C to ca. 6 vol.% for the samples annealed at 1600 °C. Moreover, three different conduction regimes are identified in SiOC/C, depending on its sp2 carbon content: (i) at low carbon contents (i.e., <1 vol.%), the silicon oxycarbide glassy matrix dominates the charge carrier transport, which exhibits an activation energy of ca. 1 eV and occurs within localized states, presumably dangling bonds; (ii) near the percolation threshold, tunneling or hopping of charge carriers between spatially separated sp2 carbon precipitates appear to be responsible for the electrical conductivity; (iii) whereas above the percolation threshold, the charge carrier transport is only weakly activated (Ea = 0.03 eV) and is realized through the (continuous) carbon phase. Hall measurements on SiOC/C samples above the percolation threshold indicate p-type carriers mainly contributing to conduction. Their density is shown to vary with the sp2 carbon content in the range from 1014 to 1019 cm-3; whereas their mobility (ca. 3 cm2/V) seems to not depend on the sp2 carbon content.

Radiological evaluations of low cost wollastonite nano-ceramics graft doped with iron oxide in the treatment of induced defects in canine mandible

Wollastonite with/without maghemite [(Fe2O3), 0, 3 and 10 wt%] was prepared by facile wet precipitation method. Effect of Fe2O3 presence in the obtained nano-ceramics on physical structure, morphology, size and the mechanical features was evaluated using X-ray diffraction, transmission electron microscope, and universal testing machine. Moreover, the in vitro biomineralization was examined using simulated body fluid (SBF) by means of scanning electron microscope/energy dispersive X-ray, Fourier transform infrared, and inductively coupled plasma. An in vivo study was conducted on 24 adult male mongrel dogs to test the biosafety of fabricated samples in the reconstruction of experimentally induced mandibular bone defects. Bone density was measured through cone beam computed tomography analysis conducted at 1 and 3 months following surgery. Wollastonite was the main phase in all the prepared samples however little maghemite was developed in Fe-containing samples. No remarkable changes were recognized for physical structure of obtained microcrystalline structures, however, a decrease in particle size was noted in the existence of Fe2O3 (10-15 nm) when compared to the pure wollastonite (30-50 nm). Mechanical features were dependent on the included Fe2O3 concentration within the wollastonite ceramic matrix. The degree of biomineralization of the samples immersed in SBF was elevated with the increase in Fe2O3 percentage. Clinically, the reconstruction of bone defects was uneventful without any adverse toxic effect. Bone density was significantly increased at 1 and 3 months (p < .001) in grafted defects compared to control ones. Increasing the doping concentrations of iron oxide was associated with significant increase (p < .001) of bone density in all induced defects. Due to the impressive healing effect of current fabricated nano-ceramics, they are recommended to be utilized as low cost bone graft alternatives.