Chitosan-Based Bioactive Glass Gauze: Microstructural Properties, In Vitro Bioactivity, and Biological Tests

Sustainable heavy metal (Cr(VI) ion) remediation: Ternary blend approach with chitosan, carboxymethyl cellulose, and bioactive glass

Heavy metal pollution poses a significant environmental challenge to worldwide, especially in developing countries. This study focuses on eliminating the heavy metal chromium (VI) ion from wastewater, employing an eco-friendly and economical ternary blend composed of Chitosan (CS), Carboxymethyl cellulose (CMC), and bioactive glass (BAG). The innovative bioactive glass is crafted from biosilica extracted from biowaste of cow dung ash, calcium oxide from eggshell ash, and phosphorus pentoxide. The CS/CMC/BAG blend is prepared via sol-gel method and characterized using XRD, FT-IR, TGA, BET, TEM and SEM revealing a porous structural morphology during blending. Batch adsorption studies explore various parameters such as pH, adsorbent dose, contact time and initial metal ion concentrations. The results are then evaluated through adsorption kinetics and adsorption isotherms (Langmuir, Freundlich, D-R, and Temkin isotherm modeling). The investigation concludes that the optimal conditions for Cr (VI) removal are pH 3, contact time of 300 min, adsorbent dosage of 0.5 g, and an initial metal ion concentration of 50 ppm. The adsorption isotherm model indicates an excellent fit with the Freundlich isotherm (R2 = 0.9576) and pseudo-second-order kinetics (R2 = 0.981). In summary, the CS/CMC/BAG ternary blend exhibits a remarkable ability to effectively remove heavy metal Cr(VI) ions from industrial wastewater.

Green Electrospun Poly(vinyl alcohol)/Gelatin-Based Nanofibrous Membrane by Incorporating 45S5 Bioglass Nanoparticles and Urea for Wound Dressing Applications: Characterization and In Vitro and In Vivo Evaluations

This study reports the fabrication and characterization of poly(vinyl alcohol) (PVA) and gelatin (Gel)-based nanofiber membranes cross-linked with citric acid (CA) by a green electrospinning method in which nano 45S5 bioglass (BG) and urea were incorporated. Various combinations of PVA, gelatin, and BG were prepared, and nanofiber membranes with average fiber diameters between 238 and 595 nm were fabricated. Morphological, chemical, and mechanical properties, porosity, swelling, water retention, and water vapor transmission rate of the fabricated membranes were evaluated. PVA:Gel (90:10), 15% CA, and 3% BG were determined as the optimum blend for nanofiber membrane fabrication via electrospinning. The membrane obtained using this blend was further functionalized with 10% w/w polymer urea coating by the electrospray method following the cross-linking. In vitro biocompatibility tests revealed that the fabricated membranes were all biocompatible except for the one that functionalized with urea. In vivo macroscopic and histopathological analysis results of PVA/Gel/BG and PVA/Gel/BG/Urea treated wounds indicated increased collagenization and vascularization and had an anti-inflammatory effect. Furthermore, careful examination of the in vivo macroscopic results of the PVA/Gel/BG/Urea membrane indicated its potential to decrease uneven scar formation. In conclusion, developed PVA/Gel/BG and PVA/Gel/BG/Urea electrospun membranes with multifunctional and biomimetic features may have the potential to be used as beneficial wound dressings.

Towards Complex Tissues Replication: Multilayer Scaffold Integrating Biomimetic Nanohydroxyapatite/Chitosan Composites

This study explores an approach to design and prepare a multilayer scaffold mimicking interstratified natural tissue. This multilayer construct, composed of chitosan matrices with graded nanohydroxyapatite concentrations, was achieved through an in situ biomineralization process applied to individual layers. Three distinct precursor concentrations were considered, resulting in 10, 20, and 30 wt% nanohydroxyapatite content in each layer. The resulting chitosan/nanohydroxyapatite (Cs/n-HAp) scaffolds, created via freeze-drying, exhibited nanohydroxyapatite nucleation, homogeneous distribution, improved mechanical properties, and good cytocompatibility. The cytocompatibility analysis revealed that the Cs/n-HAp layers presented cell proliferation similar to the control in pure Cs for the samples with 10% n-HAp, indicating good cytocompatibility at this concentration, while no induction of apoptotic death pathways was demonstrated up to a 20 wt% n-Hap concentration. Successful multilayer assembly of Cs and Cs/n-HAp layers highlighted that the proposed approach represents a promising strategy for mimicking multifaceted tissues, such as osteochondral ones.

Amikacin sulphate loaded chitosan-diopside nanoparticles composite scaffold for infectious wound healing

A wound dressing material should inhibit infections that may occur at the wound site, and at the same time, it should enhance the healing process. In this study, we developed an amikacin sulphate (AK) incorporated chitosan (Ch) and Diopside nanoparticles composite dressing (Ch-nDE-AK) for controlling wound infection and healing. The diopside nanoparticles (nDE) were prepared using sol-gel synthesis and characterized using XRD, FT-IR, and FESEM. nDE shows a size range of 142 ± 31 nm through FESEM analysis. Later, the developed composite dressing was characterized using SEM, EDS, and FT-IR analysis. Ch-nDE-AK dressing possesses a porous nature that will aid in easy cell infiltration and proliferation. The swelling studies indicated the expansion capability of the scaffold when applied to the injured site. Ch-nDE-AK scaffold showed a 69.6 ± 8.2 % amikacin sulphate release up to 7 days, which indicates the sustained release of the drug from Ch-nDE-AK scaffold. The drug release data was subjected to various kinetics models and was observed to follow the Higuchi model. The scaffold showed antibacterial activity against ATCC strains of S. aureus and E. coli for 7 days by in vitro. Ch-nDE-AK scaffold also showed antibacterial activity against S. aureus and E. coli clinical strains in vitro. The ex vivo antibacterial study confirmed the antibacterial ability of Ch-nDE-AK scaffold against S. aureus and E. coli. Ch-nDE-AK scaffold also exhibits anti-biofilm activity against S. aureus and E. coli. The Ch-nDE-AK scaffold showed cytocompatibility and cell attachment to fibroblast cells. Additionally, the scratch assay using fibroblast cells confirmed the role of the nDE in the scaffold, helping in cell migration. Thus, the developed Ch-nDE-AK dressing can potentially be used to treat infectious wound healing.

Metal-polyphenol networks-modified tantalum plate for craniomaxillofacial reconstruction

Using three-dimensional (3D) printing technology to make the porous tantalum plate and modify its surface. The physicochemical properties, cytocompatibility, antioxidant capacity, and histocompatibility of the modified materials were evaluated to prepare for the repair of craniomaxillofacial bone defects. The porous tantalum plates were 3D printed by selective laser melting technology. Tantalum plates were surface modified with a metal polyphenol network. The surface-modified plates were analyzed for cytocompatibility using thiazolyl blue tetrazolium bromide and live/dead cell staining. The antioxidant capacity of the surface-modified plates was assessed by measuring the levels of intracellular reactive oxygen species, reduced glutathione, superoxide dismutase, and malondialdehyde. The histocompatibility of the plates was evaluated by animal experiments. The results obtained that the tantalum plates with uniform small pores exhibited a high mechanical strength. The surface-modified plates had much better hydrophilicity. In vitro cell experiments showed that the surface-modified plates had higher cytocompatibility and antioxidant capacity than blank tantalum plates. Through subcutaneous implantation in rabbits, the surface-modified plates demonstrated good histocompatibility. Hence, surface-modified tantalum plates had the potential to be used as an implant material for the treatment of craniomaxillofacial bone defects.

A biomimetic multi-layer scaffold with collagen and zinc doped bioglass as a skin-regeneration agent in full-thickness injuries and its effects in vitro and in vivo

Due to the multilayer structure of skin tissue, the fabrication of a 3-layer scaffold could result in planned dermal regeneration. Herein, polyurethane (PU) and polycaprolactone (PCL), as a function of their mechanical stability and collagen due to its arginine-glycine-aspartic acid sequences, zinc ions because of overcoming the common problems of biological factors were employed. The scaffolds' physical, mechanical, and biological properties were examined by SEM, FTIR, contact angle, mechanical tensile, bacteriocidal efficacy, and hemolysis. Also, after L-929 fibroblast seeding, their biological activity was determined by SEM, DAPI, and MTT assays. Then, the cell-seeded scaffolds were implanted in full-thickness wounds of rats and evaluated by wound closure, histological, and molecular techniques. The in vivo studies showed better wound closure with the composite scaffold containing zinc ions. While its dermal re-organization was retarded in the presence of zinc ions compared to the composite scaffold containing non-doped bioglass. Despite this, the doped composite scaffold indicated better observations with the histological evaluations than the nontreated and bare scaffold groups. Real-time PCR confirmed the higher expression of FGF2 and FGFR genes in rats treated with the zinc-doped composite scaffold. In conclusion, PU/PCL-collagen/PCL-collagen containing the doped or non-doped nanoparticles showed better potential to heal dermal injuries.

Aromatherapeutic and Antibacterial Properties of Cotton Materials Treated with Emulsions Containing Peppermint Essential Oil (Menthae piperitae aetheroleum)

The objective of the work was to obtain materials with aromatherapeutic and antibacterial properties by applying emulsions based on peppermint essential oil (PEO) onto cotton fabric. For this purpose, some emulsions based on PEO incorporated in various matrices (chitosan + gelatin + beeswax; chitosan + beeswax; gelatin + beeswax and gelatin + chitosan) were prepared. Tween 80 was used as a synthetic emulsifier. The influence of the nature of matrices and of the concentration of Tween 80 on the stability of the emulsions was evaluated by the creaming indices. The materials treated with the stable emulsions were analyzed in terms of sensory activity, of the comfort characteristics, and of the gradual release of the PEO in the artificial perspiration solution. The sum of volatile components retained by samples after exposure to air was determined by GC-MS. The results regarding antibacterial activity showed that materials treated with emulsions have a good inhibitory effect on S. aureus (diameters of the inhibition zones between 53.6 and 64.0 mm) and on E. coli (diameters of the inhibition zones between 38.3 and 64.0 mm). Our data suggest that by applying peppermint-oil-based emulsions on a cotton support, aromatherapeutic patches, bandages and dressings with antibacterial properties can be obtained.

Chitosan-Based Biomaterials for Bone Tissue Engineering Applications: A Short Review

Natural bone tissue is composed of calcium-deficient carbonated hydroxyapatite as the inorganic phase and collagen type I as the main organic phase. The biomimetic approach of scaffold development for bone tissue engineering application is focused on mimicking complex bone characteristics. Calcium phosphates are used in numerous studies as bioactive phases to mimic natural bone mineral. In order to mimic the organic phase, synthetic (e.g., poly(ε-caprolactone), polylactic acid, poly(lactide-co-glycolide acid)) and natural (e.g., alginate, chitosan, collagen, gelatin, silk) biodegradable polymers are used. However, as materials obtained from natural sources are accepted better by the human organism, natural polymers have attracted increasing attention. Over the last three decades, chitosan was extensively studied as a natural polymer suitable for biomimetic scaffold development for bone tissue engineering applications. Different types of chitosan-based biomaterials (e.g., molded macroporous, fiber-based, hydrogel, microspheres and 3D-printed) with specific properties for different regenerative applications were developed due to chitosan's unique properties. This review summarizes the state-of-the-art of biomaterials for bone regeneration and relevant studies on chitosan-based materials and composites.

Salvianolic acid B dry powder inhaler for the treatment of idiopathic pulmonary fibrosis

Idiopathic pulmonary fibrosis (IPF) is a serious and fatal pulmonary inflammatory disease with an increasing incidence worldwide. The drugs nintedanib and pirfenidone, are listed as conditionally recommended drugs in the “Evidence-Based Guidelines for the Diagnosis and Treatment of Idiopathic Pulmonary Fibrosis”. However, these two drugs have many adverse reactions in clinical application. Salvianolic acid B (Sal B), a water-soluble component of Salvia miltiorrhiza, could alleviate bleomycin-induced peroxidative stress damage, and prevent or delay the onset of IPF by regulating inflammatory factors and fibrotic cytokines during the disease's progression. However, Sal B is poorly absorbed orally, and patient compliance is poor when administered intravenously. Therefore, there is an urgent need to find a new non-injection route of drug delivery. In this study, Sal B was used as model drug and l-leucine (LL) as excipient to prepare Sal B dry powder inhaler (Sal B-DPI) by spray drying method. Modern preparation evaluation methods were used to assess the quality of Sal B-DPI. Sal B-DPI is promising for the treatment of IPF, according to studies on pulmonary irritation evaluation, in vivo and in vitro pharmacodynamics, metabolomics, pharmacokinetics, and lung tissue distribution.

Bioactive Bilayer Glass Coating on Porous Titanium Substrates with Enhanced Biofunctional and Tribomechanical Behavior

The use of porous titanium samples fabricated by space-holder powder metallurgy with bioactive coatings has already been reported to prevent resorption of the bone surrounding the implant and improve osseointegration, respectively. However, the presence of pores as well as the poor adherence and the brittle behavior inherent to glassy coatings affect the service behavior of implants fabricated from these samples. Therefore, they need to be optimized. In this work, 50 vol.% of porosity titanium substrates were manufactured with different pore range size (100–200 and 355–500 µm) spacer particles and coated with a bilayer of bioactive glasses (45S5/1393). The effect of the pores on the tribomechanical properties and infiltration of the bioactive glass 1393 along with the bioactivity of the bioactive glass 45S5 were evaluated by instrumented micro-indentation and scratch tests and the formation of hydroxyapatite in simulated body fluid. The results obtained were very promising as potential implants for the replacement of small tumors in cortical bone tissues, mainly due to the smaller pores that present an improved biomechanical and biofunctional balance.

A New Generation of Electrospun Fibers Containing Bioactive Glass Particles for Wound Healing

Chitosan fibers blended with polyethylene oxide (CHIT_PEO) and crosslinked with genipin were fabricated by electrospinning technique. Subsequently, CHIT_PEO bioactive glass composite electrospun mats were fabricated with the aim to achieve flexible structures with adequate mechanical properties and improved biological performance respect to CHIT_PEO fibers, for potential applications in wound healing. Three different compositions of bioactive glasses (BG) were selected and investigated: 45S5 BG, a Sr and Mg containing bioactive glass (BGMS10) and a Zn-containing bioactive glass (BGMS_2Zn). Particulate BGs (particles size < 20 μm) were separately added to the starting CHIT_PEO solution before electrospinning. The two recently developed bioactive glasses (BGMS10 and BGMS_2Zn) showed very promising biological properties in terms of bioactivity and cellular viability; thus, such compositions were added for the first time to CHIT_PEO solution to fabricate composite electrospun mats. The incorporation of bioactive glass particles and their distribution into CHIT_PEO fibers were assessed by SEM and FTIR analyses. Furthermore, CHIT_PEO composite electrospun mats showed improved mechanical properties in terms of Young’s Modulus compared to neat CHIT_PEO fibers; on the contrary, the values of tensile strain at break (%) were comparable. Biological performance in terms of cellular viability was investigated by means of WST-8 assay and CHIT_PEO composite electrospun mats showed cytocompatibility and the desired cellular viability.

A Review of Bioactive Glass/Natural Polymer Composites: State of the Art

Collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose are biocompatible and non-cytotoxic, being attractive natural polymers for medical devices for both soft and hard tissues. However, such natural polymers have low bioactivity and poor mechanical properties, which limit their applications. To tackle these drawbacks, collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose can be combined with bioactive glass (BG) nanoparticles and microparticles to produce composites. The incorporation of BGs improves the mechanical properties of the final system as well as its bioactivity and regenerative potential. Indeed, several studies have demonstrated that polymer/BG composites may improve angiogenesis, neo-vascularization, cells adhesion, and proliferation. This review presents the state of the art and future perspectives of collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose matrices combined with BG particles to develop composites such as scaffolds, injectable fillers, membranes, hydrogels, and coatings. Emphasis is devoted to the biological potentialities of these hybrid systems, which look rather promising toward a wide spectrum of applications.

Effects of a Novel Bioactive Glass Composition on Biological Properties of Human Dental Pulp Stem Cells

Functional reconstruction of bone defects represents a clinical challenge in the regenerative medicine field, which targets tissue repair following traumatic injuries and disease-related bone deficiencies. In this regard, the optimal biomaterial should be safe, biocompatible and tailored in order to promote the activation of host progenitor cells towards bone repair. Bioactive glasses might be suitable biomaterials due to their composition being able to induce the host healing response and, eventually, anti-bacterial properties. In this study we investigated whether and how an innovative bioactive glass composition, called BGMS10, may affect cell adhesion, morphology, proliferation, immunomodulation and osteogenic differentiation of human dental pulp stem cells (hDPSCs). When cultured on BGMS10, hDPSCs maintained their proliferation rate and typical fibroblast-like morphology, showing the expression of stemness markers STRO-1 and c-Kit. Moreover, the expression of FasL, a key molecule in mediating immunomodulation effects of hDPSCs, was maintained. BGMS10 also proved to trigger osteogenic commitment of hDPSCs, as confirmed by the activation of bone-related transcription factors RUNX2 and Osx and the ongoing deposition of extracellular matrix supported by the expression of OPN and OCN. Our findings suggest that BGMS10 not only maintains the typical biological and immunomodulatory properties of hDPSCs but also favors the osteogenic commitment.

Incorporation of Bioactive Glasses Containing Mg, Sr, and Zn in Electrospun PCL Fibers by Using Benign Solvents

Poly(ε-caprolactone) (PCL) and PCL/bioactive glass composite fiber mats were produced by electrospinning technique. To improve cell adhesion and proliferation (i) 45S5, (ii) a bioactive glass containing strontium and magnesium oxides, and (iii) a bioactive glass containing zinc oxide were separately added to the starting PCL solution before electrospinning. A good incorporation of bioactive glass particles in PCL electrospun mats was confirmed by SEM and FTIR analyses. Bioactivity was evaluated by immersion of PCL mats and PCL/bioactive glass electrospun fiber mats in simulated body fluid (SBF). Bone murine stromal cells (ST-2) were employed in WST-8 assay to assess cell viability, cell morphology, and proliferation. The results showed that the presence of bioactive glass particles in the fibers enhances cell adhesion and proliferation compared to neat PCL mats. Furthermore, PCL/bioactive glass electrospun mats showed higher wound-healing rate (measured as cell migration rate) in vitro compared to neat PCL electrospun mats. Therefore, the characteristics of the PCL matrix combined with biological properties of bioactive glasses make PCL/bioactive glass composite ideal candidate for biomedical application.

A Comprehensive Review of Bioactive Glass Coatings: State of the Art, Challenges and Future Perspectives

Bioactive glasses are promising biomaterials for bone and tissue repair and reconstruction, as they were shown to bond to both hard and soft tissues stimulating cells towards a path of regeneration and self-repair. Unfortunately, due to their relatively poor mechanical properties, such as brittleness, low bending strength and fracture toughness, their applications are limited to non-load-bearing implants. However, bioactive glasses can be successfully applied as coatings on the surface of metallic implants to combine the appropriate mechanical properties of metal alloys to bioactivity and biocompatibility of bioactive glasses. In this review, several available coating techniques to coat metal alloys using bioactive glasses are described, with a special focus on thermal spraying, which nowadays is the most used to deposit coatings on metallic implants.