Carbon Nanotubes and Polydopamine Modified Poly(dimethylsiloxane) Sponges for Efficient Oil-Water Separation

The effect of chemical bond and solvent solubility parameter on stability and absorption value of functionalized PU sponge

Seawater pollution from various sources such as industrial effluents, ship washing at sea, and oil spills harm humans and the marine environment. Therefore, finding ways to eliminate this pollution is crucial. This study successfully modified a polyurethane sponge through a simple dip-coating method with functionalized graphene oxide incorporating octadecylamine and oleic acid, resulting in a hydrophobic sponge capable of absorbing crude oil and various organic solvents. Characterization analyses confirmed the synthesis. The absorption capacity of the modified sponges was examined, for example, the PU sponge has absorbed 4 g/g engine oil, while the modified GO-ODA-PU sponge has increased its absorption to 36 g/g. The GO-ODA-PU sponge demonstrated great reusability compared to the GO-OA-PU sponge owing to the strong covalent bond formed between GO and ODA, which is superior to the weak hydrogen bond formed between GO and OA. The absorption capacity of the GO-OA-PU sponge decreased by 30%. The contact angle test showed that GO-ODA-PU and GO-OA-PU sponges had contact angles of 131° and 115°, respectively. Additionally, the GO-ODA-PU sponge performed optimally for semi-polar solvents in the solubility parameter range of 18-19, with its absorption capacity reaching its maximum value. The amount of oil recycling is even possible up to 98%.

Complex treatment of oily polluted waters by modified melamine foams: from colloidal emulsions to a free oil removal

This study deals with the efficient, low-cost, and scalable treatment of oily polluted waters including colloidal emulsions, oil-in-water mixtures, and free oil removal using melamine foams (MFs) modified by ferric chloride (FeCl3). Modified foams have superhydrophobic character due to the coordination of Fe3+ with free electron pairs on nitrogen and oxygen atoms within the melamine structure. The water contact angles (WCA) were 146° ± 2°, 148° ± 4°, 153° ± 2°, and 150° ± 4° for foams modified by the solutions with concentrations of 0.001 M, 0.005 M, 0.01 M, and 0.02 M, respectively. This modification enables the efficient treatment of various oil/water systems, including oil/water colloidal emulsions (99 vol% of the droplets have dimensions below 500 nm), oil-in-water mixtures up to 40 weight % of the oil component, and "free" oil removal as it was demonstrated in this study for the first time. The emulsions containing 100 ppm diesel oil (DO) were separated with 91.4% efficiency, and the mixtures containing 20 and 40 weight % DO were separated with 99.9% efficiency. Modified foams also quickly remove free DO from the water surface, absorbing 95 g/g DO, whereas water sorption was negligible. The separation of colloidal oil in water emulsions represents the key finding of this study as it indicates the applicability of the treated MFs for the treatment of emulsified industrial wastewater. The demulsification mechanism is based on multiple diffusion processes running at different time scales, including diffusion of the emulsion into the foam and diffusion of oil droplets within the foam, combined with parallel adsorption of oil droplets onto the solid skeleton of the foam. A multiplied usage of these foams for all these niche operations was also proven. The application of our current study with previous studies on modified MFs and polyurethane for water oil separation utilization is summarized in Table S1 ESI.

Carbon Nanotube Enhanced Filtration and Dewatering of Kerosene

Current approaches to dewatering aviation fuel such as kerosene are adsorption by activated charcoal, gravity separation, etc. The objective of this work is to develop and demonstrate the filtration and dewatering of kerosene using a carbon nanotube immobilised membrane (CNIM). Highly hydrophobic membranes were prepared by immobilising carbon nanotube (CNTs) over polytetrafluoroethylene (PTFE) and polyvinylidene difluoride (PVDF) microfiltration membrane for the dewatering of ppm level water from kerosene. The effects of different CNT concentrations on membrane morphology, hydrophobicity, porosity, and permeability were characterised. After immobilising CNT into membranes, the contact angle increased by 9%, 16%, and 43% compared to unmodified 0.1 μm PTFE, 0.22 μm PTFE and 0.22 μm PVDF membranes, respectively. The CNIM showed remarkable separation efficiency for the fuel-water system. The micro/nano water droplets coalesced on the CNT surface to form larger diameters of water droplets detached from the membrane surface, leading to enhanced water rejection. In general, the water rejection increased with the amount of CNT immobilised while the effective surface porosity over pore length and flux decreased. PTFE base membrane showed better performance compared to the PVDF substrate. The CNIMs were fabricated with 0.1 and 0.22 μm PTFE at an optimised CNT loading of 3 and 6 wt.%, and the water rejection was 99.97% and 97.27%, respectively, while the kerosene fluxes were 43.22 kg/m2·h and 55.44 kg/m2·h respectively.

The Influence of Self-Heating Iron on the Thermal, Mechanical, and Swelling Properties of PDMS Composites for Organic Solvents Removal

Volatile organic compounds pollute the environment and pose a serious threat to human health due to their toxicity, mutagenicity, and carcinogenicity. In this context, it is highly desirable to fabricate high-performance poly (dimethylsiloxane) (PDMS) composites to remove organic solvents from the environment using a simple technique. Therefore, in the present study, Fe-PDMS composites were fabricated using a technique based on magnetic induction heating with iron particles serving as a self-heating agent. Under an alternating magnetic field, the iron particles served as a thermal source that assisted in the progression of PDMS crosslinking. The influence of self-heating iron on the properties of the fabricated Fe-PDMS composites was also investigated. The hydrosilation reaction occurring during the crosslinking process was controlled using FT-IR. The heating efficiency of PDMS 1, PDMS 2, and PDMS 3 was studied as the function of induction time (0–5 min) and the function of iron content (0%, 1%, and 30% wt.%). The results revealed that the mechanical properties of the PDMS 2 composite were enhanced compared to those of the PDMS 1 and PDMS 3 composites. The mechanical properties of PDMS 3 were the least efficient due to cluster formation. PDMS 3 exhibited the highest thermal stability among all composites. Furthermore, the swelling behavior of different materials in various organic solvents was studied. PDMS was observed to swell to the greatest extent in chloroform, while swelling to a large extent was observed in toluene, pentane, and petroleum ether. PDMS swelling was the least in n-butanol. The elastomeric behavior of crosslinked PDMS, together with its magnetic character, produces stimuli-responsive magneto-rheological composites, which are quite efficient and suitable for applications involving the removal of organic solvents.

Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.