Study of the Properties of Antifriction Rings under Severe Plastic Deformation

Recyclable Materials for Ecofriendly Technology

This Special Issue (SI), "Recyclable Materials for Ecofriendly Technology", has been proposed and organized as a means to present recent developments in the field of environmentally friendly designed construction and building materials. For this purpose, dozens of articles were included or considered for inclusion in this SI, covering various aspects of the topic. A comparison of these articles with other modern articles on this topic is carried out, which proves the prospects and relevance of this SI. Furthermore, per the editorial board's journal suggestion, the second volume of this successful SI is being organized, in which authors from various countries and organizations are invited to publish their new and unpublished research work.

Thermodynamic Simulation of Environmental and Population Protection by Utilization of Technogenic Tailings of Enrichment

During mining, only 4-8% is converted to final products, and the rest is accumulated in landfills. There is a lack of research on the study of various patterns and mechanisms of the formation of cement clinker minerals during the simultaneous distillation of zinc. This paper presents studies of thermodynamic stimulation of environmental and population protection by utilization of technogenic enrichment waste as secondary raw materials for clinker production and zinc extraction. In particular, a comparison of the Gibbs energy (ΔG) of clinker formation under standard chemical equations and under non-standard chemical equations is given. According to the results of the study, using thermodynamic simulation, the temperature intervals of mineral formation, the dependence of the Gibbs energy on temperature (ΔG_T°), and the approximation equations were found; it was established that the presence of zinc ferrite contributes to the intensification of the formation of clinker minerals and the extraction of Zn to gas.

Analysis of Stress-Strain State for a Cylindrical Tank Wall Defected Zone

In the study, experimental and theoretical studies were carried out to assess the influence of the shapes of dents in the tank wall on the stress-strain state of the defect zone. By testing fragments of a cylindrical tank, it was found that the most appropriate expression is (5), which could take into account the leaching of the tank wall, resulting in a decrease in the stress concentration index. At the same time, during theoretical studies in this paper, it was found that polynomials determined the stress concentration coefficient, where the obtained analytical expression data were compared with the data determined numerically in the ANSYS program, and it was found that the spread was from 2% to 10%. According to the results of a numerical study of the stress-strain state of the dent zone in the tank wall, graphical dependences of the stress concentration coefficient on the dimensionless depth of the dent for various values of the dimensionless radius of the dents and do not exceed 2% of the indicators that are obtained. At the conclusion of the experimental and numerical studies, a conclusion was made about the degree of influence of the geometric dimensions of the dents on the stress concentration index.

Experimental Analysis of the Stress State of a Prestressed Cylindrical Shell with Various Structural Parameters

The paper presents the results of experimental studies of the features of the operation of prestressed shells, taking into account the various structural parameters of the prestress. It is established that when the winding angle changes from perpendicular to the shell axis to 75° and 65°, the circumferential stresses decrease 1.4 times and 1.2 times, respectively, and the axial stresses increase five and three times, which are two and four times lower than the circumferential, from which it can be concluded that the reduction in the winding angle to the longitudinal the axis of the shell has a positive effect on the stress state of the structure. The study also found that with an increase in the diameter of the winding wire from 1 to 2 mm and a change in the winding angle, the same nature of the stress distribution is observed, but the values of the stress state parameter change, so the efficiency increases up to 25% due to an increase in the winding thickness, depending on the pitch, angle and thickness of the winding, which favorably affects the strength and the bearing capacity of the structure as a whole by increasing the value of the stress state parameter. Thus, the results of the analysis will allow us to use in more detail the possibility of controlling the stress–strain state of the prestressed shell by changing the design parameters, and the results obtained can be used in design or construction, as well as when increasing the strength characteristics of the structure, which allows us to create a high-tech design optimal for these operating conditions, which can positively complement the studies conducted earlier in this direction.

Development of a Thermomechanical Treatment Mode for Stainless-Steel Rings

This article describes a technology for the thermomechanical treatment of stainless-steel piston rings. This technology makes it possible to obtain rings with an optimal combination of plastic and strength properties that is essential for piston rings. The following thermomechanical treatment is suggested for piston rings manufacturing: quenching at 1050 °C, holding for 30 min and cooling in water, then straining by the HPT method for eight cycles at cryogenic temperature and annealing at a temperature up to 600 °C. The resulting microstructure consisted of fine austenite grains sized 0.3 μm and evenly distributed carbide particles. Annealing above this temperature led to the formation of ferrite in the structure; however, preserving the maximum fraction of austenitic component is very important, since the reduction of austenite in the structure will cause a deterioration of corrosion resistance. The strength properties of steel after such treatment increased by almost two times compared with the initial ones: microhardness increased from 980 MPa to 2425 MPa, relative elongation increased by 20%. The proposed technology will improve the strength and performance characteristics of piston rings, as well as increase their service life, which will lead to significant savings in the cost of repair, replacement and downtime.

Hardening of Bimetallic Wires from Secondary Materials Used in the Construction of Power Lines

Copper-sheathed steel wires combine the conductivity of copper and the traction resistance of steel, which makes a bimetallic wire an ideal material for the construction of power lines. Currently, there is a small number of studies devoted to the change in the microstructure of steel-copper wire during its strain. Since steel and copper have different mechanical properties, these metals at the interface can be deformed in different ways. Therefore, the present research is devoted to the study of ECAP-drawing process impacts on the properties of bimetallic steel-copper wire. During the conducted studies, the possibility and efficiency of using the combined strain technology for the formation of ultrafine grained structure and increased strength properties of steel-copper wire have been proved.