3D Printing of Concrete-Geopolymer Hybrids

Let's Print an Ecology in 3D (and 4D)

The concept of ecology, historically rooted in the economy of nature, currently needs to evolve to encompass the intricate web of interactions among humans and various organisms in the environment, which are influenced by anthropogenic forces. In this review, the definition of ecology has been adapted to address the dynamic interplay of energy, resources, and information shaping both natural and artificial ecosystems. Previously, 3D (and 4D) printing technologies have been presented as potential tools within this ecological framework, promising a new economy for nature. However, despite the considerable scientific discourse surrounding both ecology and 3D printing, there remains a significant gap in research exploring the interplay between these directions. Therefore, a holistic review of incorporating ecological principles into 3D printing practices is presented, emphasizing environmental sustainability, resource efficiency, and innovation. Furthermore, the 'unecological' aspects of 3D printing, disadvantages related to legal aspects, intellectual property, and legislation, as well as societal impacts, are underlined. These presented ideas collectively suggest a roadmap for future research and practice. This review calls for a more comprehensive understanding of the multifaceted impacts of 3D printing and the development of responsible practices aligned with ecological goals.

Eco-Friendly Coal Gangue and/or Metakaolin-Based Lightweight Geopolymer with the Addition of Waste Glass

Massive amounts of deposited coal gangue derived from the mining industry constitute a crucial problem that must be solved. On the other hand, common knowledge about the recycling of glass products and the reuse of waste glass is still insufficient, which in turn causes economic and environmental problems. Therefore, this work investigated lightweight geopolymer foams manufactured based on coal gangue, metakaolin, and a mix of them to evaluate the influence of such waste on the geopolymer matrix. In addition, the effect of 20% (wt.) of waste glass on the foams was determined. Mineralogical and chemical composition, thermal behaviour, thermal conductivity, compressive strength, morphology, and density of foams were investigated. Furthermore, the structure of the geopolymers was examined in detail, including pore and structure thickness, homogeneity, degree of anisotropy, porosity with division for closed and open pores, as well as distribution of additives and pores using micro-computed tomography (microCT). The results show that the incorporation of waste glass increased compressive strength by approximately 54% and 9% in the case of coal-gangue-based and metakaolin-based samples, respectively. The porosity of samples ranged from 67.3% to 58.7%, in which closed pores constituted 0.3-1.8%. Samples had homogeneous distributions of pores and additions. Furthermore, the thermal conductivity ranged from 0.080 W/(m·K) to 0.117 W/(m·K), whereas the degree of anisotropy was 0.126-0.187, indicating that the structure of foams was approximate to isotropic.

Feasibility Review of Aerated Materials Application in 3D Concrete Printing

Recent years have witnessed a growing global interest in 3D concrete printing technology due to its economic and scientific advantages. The application of foamed concrete, renowned for its exceptional thermal and acoustic insulation properties, not only holds economic attractiveness but also aligns seamlessly with the principles of sustainable development. This study explores various solutions related to 3D printing technology in construction, discussing the design, production, and properties of foamed concrete mixtures. The integration of 3D printing and the potential for automating the entire process offers opportunities to boost productivity and reduce construction costs. Furthermore, the utilization of foamed concrete with its commendable insulation properties will enable a reduction in the usage of materials other than concrete (e.g., mineral wool, facade mesh, and polystyrene), significantly facilitating the recycling process during building demolition. This, in turn, will lead to the preservation of nonrenewable natural resources and a decrease in CO2 emissions. Despite the promising results, there have been limited studies focusing on 3D printing with foamed materials, whereas a survey of the existing body of literature indicates a notable absence of endeavors pertaining to the utilization of aerated concrete within the realm of 3D printing, especially geopolymer composites (GP) and hybrid geopolymer composites (HGP). The outcomes delineated in the ensuing discourse are demonstrative for conventionally used materials rather than the additive manufacturing variant. Hence, this work aims to systematically review existing practices and techniques related to producing foamed concrete with 3D printing technology. This analysis also contributes to the establishment of a foundational framework and furnishes a preliminary basis upon which future endeavors aimed at the 3D printing of aerated concrete can be embarked. The findings from the literature analysis justify the desirability of continuing research on this topic, particularly when considering the potential for large-scale industrial implementation. This article provides a comprehensive state of the knowledge on the development of 3D printing techniques for foamed concrete mixtures. By consolidating and analyzing findings from different studies, this article offers insights into the advancements, challenges, and potential applications of foamed concrete in additive manufacturing processes. This, in turn, contributes to the overall understanding and advancement of 3D printing technologies using foamed concrete as a versatile and sustainable construction material. The encouraging results obtained from the analysis further underscore the need for the continued exploration of 3D printing, especially with an eye towards its industrial-scale implementation.

Influence of Waste Glass Addition on the Fire Resistance, Microstructure and Mechanical Properties of Geopolymer Composites

Nowadays, humanity has to face the problem of constantly increasing amounts of waste, which cause not only environmental pollution but also poses a critical danger to human health. Moreover, the growth of landfill sites involves high costs of establishment, development, and maintenance. Glass is one of the materials whose recycling ratio is still insufficient. Therefore, in the presented work, the influence of the particle size and share of waste glass on the consistency, morphology, specific surface area, water absorption, setting time, and mechanical properties of geopolymers was determined. Furthermore, for the first time, the fire resistance and final setting time of such geopolymer composites were presented in a wide range. Based on the obtained results, it was found that the geopolymer containing 20% unsorted waste glass obtained a final setting time that was 44% less than the sample not containing waste glass, 51.5 MPa of compressive strength (135.2% higher than the reference sample), and 13.5 MPa of residual compressive strength after the fire resistance test (164.7% more than the reference sample). Furthermore, it was found that the final setting time and the total pore volume closely depended on the additive's share and particle size. In addition, the use of waste glass characterized by larger particle sizes led to higher strength and lower mass loss after exposure to high temperatures compared to the composite containing smaller ones. The results presented in this work allow not only for reducing the costs and negative impact on the environment associated with landfilling but also for developing a simple, low-cost method of producing a modern geopolymer composite with beneficial properties for the construction industry.

Influence of the In-Fill Pattern of the 3D Printed Building Wall on Its Thermal Insulation

The intensive development of 3D Concrete Printing (3DCP) technology causes constantly increased its share in the construction sector. However, in order to produce products with controlled properties, optimization of the technological process is still required. Automation of production based on additive manufacturing methods streamlines the process by comprehensively manufacturing building components that meet, among others, strength, visual, and insulation requirements. Moreover, the possibility of using computer simulations to assess the properties of the designed elements allows for a multitude of analyzed versions of the constructed partitions, which can be verified at the design stage. Thanks to such an opportunity, the process of designing building elements can be significantly improved. The article presents results related to the assessment of the level of thermal insulation of products that can be produced by additive technology, depending on the applied spatial geometry of the vertical partition and the amount and type of materials used. Eight original solutions of in-fill pattern were designed, for which both Finite Element Method (FEM) computer simulations of thermal conductivity and experimental measurements of thermal conductivity of samples were performed. On the basis of the obtained results, both the correctness of the simulation results for the various analyzed materials and their consistency with the practical results were found. Depending on the investigated geometry, for samples of the same dimensions and using the same material, the differences in the U-factor obtained by FEM analysis amounted to 61%. The best solution from the investigated spatial geometries of the vertical partitions has been indicated. The U parameter in the variant with the best thermal insulation was 0.183 W/m2K, which meets the requirements of Polish construction law. The issues discussed in this work can be the basis for the selection of the best solution possible for practical use during the production of building walls using the 3DCP method fulfilling the guidelines of applicable standards. Furthermore, they can be used as a tool for optimizing geometry in terms of energy savings and reducing waste production by both engineers developing 3DCP technologies and architects using innovative techniques for manufacturing building structures.

Metal and Polymer Based Composites Manufactured Using Additive Manufacturing-A Brief Review

This review examines the mechanical performance of metal- and polymer-based composites fabricated using additive manufacturing (AM) techniques. Composite materials have significantly influenced various industries due to their exceptional reliability and effectiveness. As technology advances, new types of composite reinforcements, such as novel chemical-based and bio-based, and new fabrication techniques are utilized to develop high-performance composite materials. AM, a widely popular concept poised to shape the development of Industry 4.0, is also being utilized in the production of composite materials. Comparing AM-based manufacturing processes to traditional methods reveals significant variations in the performance of the resulting composites. The primary objective of this review is to offer a comprehensive understanding of metal- and polymer-based composites and their applications in diverse fields. Further on this review delves into the intricate details of metal- and polymer-based composites, shedding light on their mechanical performance and exploring the various industries and sectors where they find utility.

Properties of 3D Printed Concrete-Geopolymer Hybrids Reinforced with Aramid Roving

Three-dimensional concrete printing (3DCP) is an innovative technology that can lead to breakthrough modifications of production processes in the construction industry. The paper presents for the first time the possibility of 3D printing concrete-geopolymer hybrids reinforced with aramid roving. Reference concrete samples and concrete-geopolymer hybrids composed of 95% concrete and 5% geopolymer based on fly ash or metakaolin were produced. The properties of the samples without reinforcement and samples with 0.5% (wt.) aramid roving were compared. The frost resistance tests, UV radiation resistance, and thermal conductivity were evaluated for samples that were 3D-printed or produced by the conventional casting method. Compressive strength tests were carried out for each sample exposed to freeze-thaw cycles and UV radiation. It was observed that after the frost resistance test, the samples produced by the 3D printing technology had a minor decrease in strength properties compared to the samples made by casting. Moreover, the thermal conductivity coefficient was higher for concrete-geopolymer hybrids than concrete reinforced with aramid roving.

A Scientometric Review on Mapping Research Knowledge for 3D Printing Concrete

The scientometric analysis is statistical scrutiny of books, papers, and other publications to assess the "output" of individuals/research teams, organizations, and nations, to identify national and worldwide networks, and to map the creation of new (multi-disciplinary) scientific and technological fields that would be beneficial for the new researchers in the particular field. A scientometric review of 3D printing concrete is carried out in this study to explore the different literature aspects. There are limitations in conventional and typical review studies regarding the capacity of such studies to link various elements of the literature accurately and comprehensively. Some major problematic phases in advanced level research are: co-occurrence, science mapping, and co-citation. The sources with maximum articles, the highly creative researchers/authors known for citations and publications, keywords co-occurrences, and actively involved domains in 3D printing concrete research are explored during the analysis. VOS viewer application analyses bibliometric datasets with 953 research publications were extracted from the Scopus database. The current study would benefit academics for joint venture development and sharing new strategies and ideas due to the graphical and statistical depiction of contributing regions/countries and researchers.

Investigation of Mechanical Properties and Microstructure of Construction- and Demolition-Waste-Based Geopolymers

Construction and demolition waste (CDW) is the third-most abundant waste generated annually in the countries of the European Union. One of the alternatives to the use of these wastes is geopolymeric materials. Partial replacement of commonly used raw materials for the production of these materials can help reduce the number of landfills and the consumption of natural resources. In this study, the authors partially replaced metakaolin and fly ash with clay bricks and concrete debris. The research method in article is connected with analysis of microstructures and the mechanical and physical properties of the geopolymers. The results obtained show the possibility of manufacturing useful construction materials based on industrial byproducts (fly ash) and CDW. Compressive strength and flexural strength were, for samples containing metakaolin, 20.1 MPa and 5.3 MPa, respectively. Geopolymers containing fly ash displayed 19.7 MPa of compressive strength and 3.0 MPa of flexural strength. The results for both synthesized materials give them perspectives for future applications in the construction industry.

Foamed Eco-Geopolymer Modified by Perlite and Cellulose as a Construction Material for Energy-Efficient Buildings

Irreversible climate change, including atmosphere temperature extremes, is one of the most important issues of the present time. In this context, the construction industry requires solutions for increasing the energy efficiency of buildings through feedback between temperature adjustment inside buildings and better isolation of the external parts of buildings. Newly developed thermal insulation materials play an important role in this strategy. This paper presents the foamed geopolymer based on metakaolin that can be used as a modern facade material. In order to further improve its thermal insulation properties, the composition of geopolymer was modified with organic substances, i.e., perlite and cellulose fibers (30% and 50% of the volume). The thermal conductivity and insulation properties, density, mineral phases, absorbability, and compressive strength were improved for composite materials. It has been shown that the final properties of the foamed geopolymer can be controlled to a great extent by modifications, and the final properties determine its applicability.