The Mechanical and Physical Properties of 3D-Printed Materials Composed of ABS-ZnO Nanocomposites and ABS-ZnO Microcomposites

Optimization Course of Titanium Nitride Nanofiller Loading in High-Density Polyethylene: Interpretation of Reinforcement Effects and Performance in Material Extrusion 3D Printing

In this study, titanium nitride (TiN) was selected as an additive to a high-density polyethylene (HDPE) matrix material, and four different nanocomposites were created with TiN loadings of 2.0-8.0 wt. % and a 2 wt. % increase step between them. The mixtures were made, followed by the fabrication of the respective filaments (through a thermomechanical extrusion process) and 3D-printed specimens (using the material extrusion (MEX) technique). The manufactured specimens were subjected to mechanical, thermal, rheological, structural, and morphological testing. Their results were compared with those obtained after conducting the same assessments on unfilled HDPE samples, which were used as the control samples. The mechanical response of the samples improved when correlated with that of the unfilled HDPE. The tensile strength improved by 24.3%, and the flexural strength improved by 26.5% (composite with 6.0 wt. % TiN content). The dimensional deviation and porosity of the samples were assessed with micro-computed tomography and indicated great results for porosity improvement, achieved with 6.0 wt. % TiN content in the composite. TiN has proven to be an effective filler for HDPE polymers, enabling the manufacture of parts with improved mechanical properties and quality.

Preparation and Characterization of Composites Based on ABS Modified with Polysiloxane Derivatives

In this study, organosilicon compounds were used as modifiers of filaments constituting building materials for 3D printing technology. Polymethylhydrosiloxane underwent a hydrosilylation reaction with styrene, octadecene, and vinyltrimethoxysilane to produce new di- or tri-functional derivatives with varying ratios of olefins. These compounds were then mixed with silica and incorporated into the ABS matrix using standard processing methods. The resulting systems exhibited changes in their physicochemical and mechanical characteristics. Several of the obtained composites (e.g., modified with VT:6STYR) had an increase in the contact angle of over 20° resulting in a hydrophobic surface. The addition of modifiers also prevented a decrease in rheological parameters regardless of the amount of filler added. In addition, comprehensive tests of the thermal decomposition of the obtained composites were performed and an attempt was made to precisely characterize the decomposition of ABS using FT-IR and optical microscopy, which allowed us to determine the impact of individual groups on the thermal stability of the system.

Promising New Horizons in Medicine: Medical Advancements with Nanocomposite Manufacturing via 3D Printing

Three-dimensional printing technology has fundamentally revolutionized the product development processes in several industries. Three-dimensional printing enables the creation of tailored prostheses and other medical equipment, anatomical models for surgical planning and training, and even innovative means of directly giving drugs to patients. Polymers and their composites have found broad usage in the healthcare business due to their many beneficial properties. As a result, the application of 3D printing technology in the medical area has transformed the design and manufacturing of medical devices and prosthetics. Polymers and their composites have become attractive materials in this industry because of their unique mechanical, thermal, electrical, and optical qualities. This review article presents a comprehensive analysis of the current state-of-the-art applications of polymer and its composites in the medical field using 3D printing technology. It covers the latest research developments in the design and manufacturing of patient-specific medical devices, prostheses, and anatomical models for surgical planning and training. The article also discusses the use of 3D printing technology for drug delivery systems (DDS) and tissue engineering. Various 3D printing techniques, such as stereolithography, fused deposition modeling (FDM), and selective laser sintering (SLS), are reviewed, along with their benefits and drawbacks. Legal and regulatory issues related to the use of 3D printing technology in the medical field are also addressed. The article concludes with an outlook on the future potential of polymer and its composites in 3D printing technology for the medical field. The research findings indicate that 3D printing technology has enormous potential to revolutionize the development and manufacture of medical devices, leading to improved patient outcomes and better healthcare services.

Box-Behnken modeling to quantify the impact of control parameters on the energy and tensile efficiency of PEEK in MEX 3D-printing

Currently, energy efficiency and saving in production engineering, including Material Extrusion (MEX) Additive Manufacturing, are of key importance to ensure process sustainability and cost-effectiveness. The functionality of parts made with MEX 3D-printing remains solid, especially for expensive high-performance polymers, for biomedical, automotive, and aerospace industries. Herein, the energy and tensile strength metrics are investigated over three key process control parameters (Nozzle Temperature, Layer Thickness, and Printing Speed), with the aid of laboratory-scale PEEK filaments fabricated with melt extrusion. A double optimization is attempted for the production by consuming minimum energy, of PEEK parts with improved strength. A three-level Box-Behnken design with five replicas for each experimental run was employed. Statistical analysis of the experimental findings proved that LT is the most decisive control setting for mechanical strength. An LT of 0.1 mm maximized the tensile endurance (∼74 MPa), but at the same time, it was responsible for the worst energy (∼0.58 MJ) and printing time (∼900 s) expenditure. The experimental and statistical findings are further discussed and interpreted using fractographic SEM and optical microscopy, revealing the 3D printing quality and the fracture mechanisms in the samples. Thermogravimetric analysis (TGA) was performed. The findings hold measurable engineering and industrial merit, since they may be utilized to achieve an optimum case-dependent compromise between the usually contradictory goals of productivity, energy performance, and mechanical functionality.

Effect of Short Glass Fiber Addition on Flexural and Impact Behavior of 3D Printed Polymer Composites

Fused deposition modeling (FDM), one of the most widely used additive manufacturing (AM) processes, is used for fabrication of 3D models from computer-aided design data using various materials for a wide scope of applications. The principle of FDM or, in general, AM plays an important role in minimizing the ill effects of manufacturing on the environment. Among the various available reinforcements, short glass fiber (SGF), one of the strong reinforcement materials available, is used as a reinforcement in the acrylonitrile butadiene styrene (ABS) matrix. At the outset, very limited research has been carried out till date in the analysis of the impact and flexural strength of the SGF-reinforced ABS polymer composite developed by the FDM process. In this regard, the present research investigates the impact and flexural strength of SGF-ABS polymer composites by the addition of 15 and 30 wt % SGF to ABS. The tests were conducted as per ASTM standards. Increments in flexural and impact properties were observed with the addition of SGF to ABS. The increment of 42% in impact strength was noted for the addition of 15 wt % SGF and 54% increase with the addition of 30 wt % SGF. On similar lines, flexural properties also showed improved values of 44 and 59% for the addition of 15 and 30 wt % SGF to ABS. SGF addition greatly enhanced the properties of flexural and impact strength and has paved the path for the exploration of varied values of reinforcement into the matrix.

Mechanical Reinforcement of ABS with Optimized Nano Titanium Nitride Content for Material Extrusion 3D Printing

Acrylonitrile Butadiene Styrene (ABS) nanocomposites were developed using Material Extrusion (MEX) Additive Manufacturing (AM) and Fused Filament Fabrication (FFF) methods. A range of mechanical tests was conducted on the produced 3D-printed structures to investigate the effect of Titanium Nitride (TiN) nanoparticles on the mechanical response of thermoplastic polymers. Detailed morphological characterization of the produced filaments and 3D-printed specimens was carried out using Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). High-magnification images revealed a direct impact of the TiN concentration on the surface characteristics of the nanocomposites, indicating a strong correlation with their mechanical performance. The chemical compositions of the raw and nanocomposite materials were thoroughly investigated by conducting Raman and Energy Dispersive Spectroscopy (EDS) measurements. Most of the mechanical properties were improved with the inclusion of TiN nanoparticles with a content of 6 wt. % to reach the optimum mechanical response overall. ABS/TiN 6 wt. % exhibits remarkable increases in flexural modulus of elasticity (42.3%) and toughness (54.0%) in comparison with pure ABS. The development of ABS/TiN nanocomposites with reinforced mechanical properties is a successful example that validates the feasibility and powerful abilities of MEX 3D printing in AM.

MEX 3D Printed HDPE/TiO2 Nanocomposites Physical and Mechanical Properties Investigation

Aiming to develop more robust, mechanically advanced, Fused Filament Fabrication (FFF) materials, High-Density Polyethylene (HDPE) nanocomposites were developed in the current research work. Titanium Dioxide (TiO2) was selected as filler to be incorporated into the HDPE matrix in concentration steps of 0.5, 2.5, 5, and 10 wt.%. 3D printing nanocomposite filaments were extruded in ~1.75 mm diameter and used to 3D print and test tensile and flexion specimens according to international standards. Reported results indicate that the filler contributes to increasing the mechanical strength of the virgin HDPE at certain filler and filler type concentrations; with the highest values reported to be 37.8% higher in tensile strength with HDPE/TiO2 10 wt.%. Morphological and thermal characterization was performed utilizing Scanning Electron Microscopy (SEM), Raman, Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC), while the results were correlated with the available literature.

UV-LED Curable Acrylic Films Containing Phosphate Glass Powder: Effect of the Filler Loading on the Thermal, Optical, Mechanical and Flame Retardant Properties

In this work, we thoroughly investigate the effects of the incorporation of a phosphate glass micrometric powder on the morphology, as well as on the thermal, optical, mechanical and flame retardant properties of UV-LED curable acrylic films. To this aim, the filler loading was changed within 10 and 50 wt.%. UV-LED initiated curing was selected as a fast and reliable system, as the standard UV-curing process was not suitable because of the presence of the glass powder that decreased the quantum efficiency during the UV exposure, hence preventing the transformation of the liquid system into a solid network. The glass powder slightly increased the glass transition temperature of the acrylic network, hence showing a limited effect on the chain segments mobility; besides, increasing filler loadings were responsible for a progressive decrease of the transparency of films, irrespective of a marginal effect on their refractive index. Conversely, the presence of increasing amounts of phosphate glass improved the thermal and thermo-oxidative stability of the cured products. Besides, phosphate glass was capable of remarkably enhancing the flame retardance of the acrylic network at 50 wt.% loading, which achieved self-extinction in vertical flame spread tests (and was V-0 rated). This formulation, as assessed by forced-combustion tests, also displayed a remarkable decrease of peak of Heat Release Rate and Total Heat Release (by 44 and 33%, respectively) and of Total Smoke Release and Specific Extinction Area (by 53 and 56%, respectively). Further, the filler promoted an increase of the stiffness and surface hardness of the films, at the expense of a decrease in ductility. All these findings may justify the potential use of these composite films as flame retardant coatings for different flammable substrates.

3D Printed Metal Oxide-Polymer Composite Materials for Antifouling Applications

Current technology to prevent biofouling usually relies on the use of toxic, biocide-containing materials, which can become a serious threat to marine ecosystems, affecting both targeted and nontargeted organisms. Therefore, the development of broad-spectrum, less toxic antifouling materials is a challenge for researchers; such materials would be quite important in applications like aquaculture. In this respect, surface chemistry, physical properties, durability and attachment scheme can play a vital role in the performance of the materials. In this work, acrylonitrile butadiene styrene (ABS)/micro ZnO or nano ZnO composite lattices with different metal oxide contents were developed using 3D printing. Their antifouling behavior was examined with respect to aquaculture applications by monitoring growth on them of the diatoms Navicula sp. and the monocellular algae Chlorella sp. with image analysis techniques. As shown, the presence of metal oxides in the composite materials can bring about antifouling ability at particular concentrations. The present study showed promising results, but further improvements are needed.

Properties of CAD/CAM 3D Printing Dental Materials and Their Clinical Applications in Orthodontics: Where Are We Now?

In the last years, both medicine and dentistry have come across a revolution represented by the introduction of more and more digital technologies for both diagnostic and therapeutic purposes. Additive manufacturing is a relatively new technology consisting of a computer-aided design and computer-aided manufacturing (CAD/CAM) workflow, which allows the substitution of many materials with digital data. This process requires three fundamental steps represented by the digitalization of an item through a scanner, the editing of the data acquired using a software, and the manufacturing technology to transform the digital data into a final product, respectively. This narrative review aims to discuss the recent introduction in dentistry of the abovementioned digital workflow. The main advantages and disadvantages of the process will be discussed, along with a brief description of the possible applications on orthodontics.

Optimization of Process Parameters for Fabricating Polylactic Acid Filaments Using Design of Experiments Approach

The amount of wasted polylactic acid (PLA) is increasing because 3D printing services are an increasingly popular offering in many fields. The PLA is widely employed in the fused deposition modeling (FDM) since it is an environmentally friendly polymer. However, failed prototypes or physical models can generate substantial waste. In this study, the feasibility of recycling PLA waste plastic and re-extruded it into new PLA filaments was investigated. An automatic PLA filament extruder was first developed for fabricating new PLA filaments. This paper also discusses the process, challenges, and benefits of recycling PLA waste plastic in an effort to fabricate new PLA filaments more sustainable. It was found that it was possible to fabricate PLA filament using recycled PLA waste plastic. The production cost is only 60% of the commercially available PLA filament. The tensile strength of the developed PLA filament is approximately 1.1 times that of the commercially available PLA filament. The design of experiments approach was employed to investigate the optimal process parameters for fabricating PLA filaments. The most important control factor affecting the diameter of PLA filament is the barrel temperature, followed by recycled material addition ratio, extrusion speed, and cooling distance. The optimal process parameters for fabricating PLA filament with a diameter of 1.7 mm include the barrel temperature of 184 °C, extrusion speed of 490 mm/min, cooling distance of 57.5 mm, and recycled material addition ratio of 40%.

Sustainable Additive Manufacturing: Mechanical Response of Polyamide 12 over Multiple Recycling Processes

Plastic waste reduction and recycling through circular use has been critical nowadays, since there is an increasing demand for the production of plastic components based on different polymeric matrices in various applications. The most commonly used recycling procedure, especially for thermoplastic materials, is based on thermomechanical process protocols that could significantly alter the polymers' macromolecular structure and physicochemical properties. The study at hand focuses on recycling of polyamide 12 (PA12) filament, through extrusion melting over multiple recycling courses, giving insight for its effect on the mechanical and thermal properties of Fused Filament Fabrication (FFF) manufactured specimens throughout the recycling courses. Three-dimensional (3D) FFF printed specimens were produced from virgin as well as recycled PA12 filament, while they have been experimentally tested further for their tensile, flexural, impact and micro-hardness mechanical properties. A thorough thermal and morphological analysis was also performed on all the 3D printed samples. The results of this study demonstrate that PA12 can be successfully recycled for a certain number of courses and could be utilized in 3D printing, while exhibiting improved mechanical properties when compared to virgin material for a certain number of recycling repetitions. From this work, it can be deduced that PA12 can be a viable option for circular use and 3D printing, offering an overall positive impact on recycling, while realizing 3D printed components using recycled filaments with enhanced mechanical and thermal stability.

Sustainable Additive Manufacturing: Mechanical Response of High-Density Polyethylene over Multiple Recycling Processes

Polymer recycling is nowadays in high-demand due to an increase in polymers demand and production. Recycling of such materials is mostly a thermomechanical process that modifies their overall mechanical behavior. The present research work focuses on the recyclability of high-density polyethylene (HDPE), one of the most recycled materials globally, for use in additive manufacturing (AM). A thorough investigation was carried out to determine the effect of the continuous recycling on mechanical, structural, and thermal responses of HDPE polymer via a process that isolates the thermomechanical treatment from other parameters such as aging, contamination, etc. Fused filament fabrication (FFF) specimens were produced from virgin and recycled materials and were experimentally tested and evaluated in tension, flexion, impact, and micro-hardness. A thorough thermal and morphological analysis was also performed. The overall results of this study show that the mechanical properties of the recycled HDPE polymer were generally improved over the recycling repetitions for a certain number of recycling steps, making the HDPE recycling a viable option for circular use. Repetitions two to five had the optimum overall mechanical behavior, indicating a significant positive impact of the HDPE polymer recycling aside from the environmental one.

Sustainable Additive Manufacturing: Mechanical Response of Polypropylene over Multiple Recycling Processes

The recycling of polymeric materials has received a steadily growing scientific and industrial interest due to the increase in demand and production of durable and lightweight plastic parts. Recycling of such materials is mostly based on thermomechanical processes that significantly affect the mechanical, as well as the overall physicochemical properties of polymers. The study at hand focuses on the recyclability of Fused Filament Fabrication (FFF) 3D printed Polypropylene (PP) for a certain number of recycling courses (six in total), and its effect on the mechanical properties of 3D printed parts. Namely, 3D printed specimens were fabricated from non-recycled and recycled PP material, and further experimentally tested regarding their mechanical properties in tension, flexion, impact, and microhardness. Comprehensive dynamic scanning calorimetry (DSC), thermogravimetric analysis (TGA), Raman spectroscopy, and morphological investigations by scanning electron microscopy (SEM) were performed for the different 3D printed PP samples. The overall results showed that there is an overall slight increase in the material’s mechanical properties, both in tension and in flexion mode, while the DSC characterization indicates an increase in the polymer crystallinity over the recycling course.

Flexible 3D Printed Conductive Metamaterial Units for Electromagnetic Applications in Microwaves

In this work we present a method for fabricating three dimensional, ultralight and flexible millimeter metamaterial units using a commercial household 3D printer. The method is low-cost, fast, eco-friendly and accessible. In particular, we use the Fused Deposition Modeling 3D printing technique and we fabricate flexible conductive Spilt Ring Resonators (SRRs) in a free-standing form. We characterized the samples experimentally through measurements of their spectral transmission, using standard rectangular microwave waveguides. Our findings show that the resonators produce well defined resonant electromagnetic features that depend on the structural details and the infiltrating dielectric materials, indicating that the thin, flexible and light 3D printed structures may be used as electromagnetic microwave components and electromagnetic fabrics for coating a variety of devices and infrastructure units, while adapting to different shapes and sizes.

Mechanical Properties of 3D-Printed Acrylonitrile-Butadiene-Styrene TiO2 and ATO Nanocomposites

In order to enhance the mechanical performance of three-dimensional (3D) printed structures fabricated via commercially available fused filament fabrication (FFF) 3D printers, novel nanocomposite filaments were produced herein following a melt mixing process, and further 3D printed and characterized. Titanium Dioxide (TiO₂) and Antimony (Sb) doped Tin Oxide (SnO₂) nanoparticles (NPs), hereafter denoted as ATO, were selected as fillers for a polymeric acrylonitrile butadiene styrene (ABS) thermoplastic matrix at various weight % (wt%) concentrations. Tensile and flexural test specimens were 3D printed, according to international standards. It was proven that TiO₂ filler enhanced the overall tensile strength by 7%, the flexure strength by 12%, and the micro-hardness by 6%, while for the ATO filler, the corresponding values were 9%, 13%, and 6% respectively, compared to unfilled ABS. Atomic force microscopy (AFM) revealed the size of TiO₂ (40 ± 10 nm) and ATO (52 ± 11 nm) NPs. Raman spectroscopy was performed for the TiO₂ and ATO NPs as well as for the 3D printed nanocomposites to verify the polymer structure and the incorporated TiO₂ and ATO nanocrystallites in the polymer matrix. The scope of this work was to fabricate novel nanocomposite filaments using commercially available materials with enhanced overall mechanical properties that industry can benefit from.