Preparation of Carriers Based on ZnO Nanoparticles Decorated on Graphene Oxide (GO) Nanosheets for Efficient Immobilization of Lipase from Candida rugosa

Hollow Mesoporous Carbon-Based Enzyme Nanoreactor for the Confined and Interfacial Biocatalytic Synthesis of Phytosterol Esters

Rationally designing carriers to obtain efficient and stable immobilized enzymes for the production of food raw materials is always a challenge. In this work, hollow cube carbon (HMC) as a carrier of Candida rugosa lipase (CRL) was prepared to construct a Pickering interfacial biocatalysis system, which was applied to biphasic biocatalysis. For comparison, the nonporous carbon (HC) and porous MoS₂ (HMoS₂) were also designed. On these grounds, p-NPP and linolenic acid were selected as the representative substrates for hydrolysis and esterification reactions. Under the optimal conditions, the protein loading amount, specific activity, and expressed activity of CRL immobilized on HMC (HMC@CRL) were 167.2 mg g^-1, 5.41 U mg^-1, and 32.34 U/mg protein, respectively. In the "oil-water" biphase, the relative hydrolytic activity of HMC@CRL was higher than that of HC@CRL, HMoS₂@CRL, and CRL by 50, 68, and 80%, respectively, as well as itself in one phase. Compared to other reports (1.13%), HMC@CRL demonstrated a satisfactory hydrolysis rate (3.02%) and was the fastest among all other biocatalysts in the biphase. Moreover, compared with the free CRL in one-phase system, the Pickering interfacial biphasic biocatalyst, HMC@CRL, exhibited a higher esterification rate (85%, 2.7-fold enhancement). Therefore, the HMC@CRL nanoreactors had more optimal performance in the field of biomanufacturing and food industry.

Comparative Study on Lipase Immobilized onto Organo-Cation Exchanged Kaolin and Metakaolin: Surface Properties and Catalytic Activity

Clay mineral has received much attention to be used as biocatalysts as it is cheaper, easily available and environmentally friendly. However, the use of unmodified clay, in particular kaolin for enzyme immobilization showed unsuitability of this support due to its negative charge. In this study, the hydrophobic properties of kaolin and metakaolin (kaolin heated to 650 °C) were adjusted by the intercalation with benzyltriethylammonium chloride (BTEA-Cl), at concentrations 2.0 times the cation exchange capacities (CEC) of the clays. The supports were then used for immobilization of lipase from Candida rugosa (CRL). From the study, the highest percentage of lipase immobilization was achieved (70.14%), when organo-modified metakaolin (2.0 MK) was used. The supports as well as the immobilized biocatalysts were then characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and nitrogen adsorption techniques. Comparisons of the efficiencies of immobilized with free CRL in the synthesis of nonyl hexanoate showed that immobilized CRL achieved enzymatic activities of between 5.24×10−3 to 3.63×10−3 mmol/min/mg, while free CRL achieved enzymatic activity of 3.27×10−3 mmol/min/mg after 5 h of reaction at 30 ℃. The immobilized CRLs also maintained 70.81% – 80.59% thermostabilities at 70 ℃ as compared to the free CRL (28.13%). CRL immobilized on 2.0 NK and 2.0 MK also maintained 38.54% and 62.56%, respectively, of the initial activities after 10 continuous cycles, showing the excellent stability and reusability of the immobilized lipases, suitable as substitute for expensive, hazardous catalysts used in industries. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Ternary biogenic silica/magnetite/graphene oxide composite for the hyperactivation of Candida rugosa lipase in the esterification production of ethyl valerate

Oil palm leaves (OPL) silica (SiO₂) can replace the energy-intensive, commercially produced SiO₂. Moreover, the agronomically sourced biogenic SiO₂ is more biocompatible and cost-effective enzyme support, which properties could be improved by the addition of magnetite (Fe₃O₄) and graphene oxide (GO) to yield better ternary support to immobilize enzymes, i.e., Candida rugosa lipase (CRL). This study aimed to optimize the Candida rugosa lipase (CRL immobilization onto the ternary OPL-silica-magnetite (Fe₃O₄)-GO (SiO₂/Fe₃O₄/GO) support, for use as biocatalyst for ethyl valerate (EV) production. Notably, this is the first study detailing the CRL/SiO₂/Fe3O4/GO biocatalyst preparation for rapid and high yield production of ethyl valerate (EV). AFM and FESEM micrographs revealed globules of CRL covalently bound to GL-A-SiO₂/Fe₃O₄/GO; similar to Raman and UV-spectroscopy results. FTIR spectra revealed amide bonds at 3478 cm^-1 and 1640 cm^-1 from covalent interactions between CRL and GL-A-SiO₂/Fe₃O₄/GO. Optimum immobilization conditions were 4% (v/v) glutaraldehyde, 8 mg/mL CRL, at 16 h stirring in 150 mM NaCl at 30 °C, offering 24.78 ± 0.26 mg/g protein (specific activity = 65.24 ± 0.88 U/g). The CRL/SiO₂/Fe₃O₄/GO yielded 77.43 ± 1.04 % of EV compared to free CRL (48.75 ± 0.70 %), verifying the suitability of SiO₂/Fe₃O₄/GO to hyperactivate and stabilize CRL for satisfactory EV production.

Armoring bio-catalysis via structural and functional coordination between nanostructured materials and lipases for tailored applications

Nanostructured materials represent an interesting and novel class of support matrices for the immobilization of different enzymes. Owing to the high surface area, robust mechanical stability, outstanding optical, thermal, and electrical properties, nanomaterials have been rightly perceived as desired immobilization matrices for lipases immobilization with a wide array of biotechnological applications such as dairy, food technology, fine chemical, pharmaceutical, detergent, and oleochemical industries. Lipases immobilized on nanomaterials have demonstrated superior attributes than free counterparts, such as aggrandized pH and thermal stability, robustness, long-term stability, and the possibility of reuse and recycling in several times. Here we review current and state-of-the-art literature on the use of nanomaterials as novel platforms for the immobilization of lipase enzymes. The physicochemical properties and exploitation of a large number of new nanostructured materials such as carbon nanotubes, nano-silica, graphene/graphene oxide, metal nanoparticles, magnetic nanostructures, metal-organic frameworks, and hybrid nanoflowers as a host matrix to constitute robust lipases-based nanobiocatalytic systems are discussed. Conclusive remarks, trends, and future recommendations for nanomaterial immobilized enzymes are also given.

Advances in Recombinant Lipases: Production, Engineering, Immobilization and Application in the Pharmaceutical Industry

Lipases are one of the most used enzymes in the pharmaceutical industry due to their efficiency in organic syntheses, mainly in the production of enantiopure drugs. From an industrial viewpoint, the selection of an efficient expression system and host for recombinant lipase production is highly important. The most used hosts are Escherichia coli and Komagataella phaffii (previously known as Pichia pastoris) and less often reported Bacillus and Aspergillus strains. The use of efficient expression systems to overproduce homologous or heterologous lipases often require the use of strong promoters and the co-expression of chaperones. Protein engineering techniques, including rational design and directed evolution, are the most reported strategies for improving lipase characteristics. Additionally, lipases can be immobilized in different supports that enable improved properties and enzyme reuse. Here, we review approaches for strain and protein engineering, immobilization and the application of lipases in the pharmaceutical industry.

Melamine-based Covalent Organic Polymers (MCOPs) as Lipase Nanocarrier for Recyclable Esters Hydrolysis and Transesterification

Present study has successfully synthesized melamine-based covalent organic polymers (MCOPs) and applied it as lipase carrier for recyclable esters hydrolysis and transesterification. The synthesized MCOPs are composed of dense nanosheet structures having a thickness of 3.5 nm. Three immobilization methods namely physical adsorption, cross-linking and carrier activation were employed to prepare the MCOPs-immobilized CRL. Cross-linked MCOPs-immobilized CRL (41.30 mg protein/g MCOPs) and carrier activated MCOPs-immobilized CRL (33.20 mg protein/g MCOPs) had higher enzyme loading as compared to physical absorb MCOPs-immobilized CRL (29.30 mg protein/g MCOPs). Nevertheless, physical absorb MCOPs-immobilized CRL demonstrated the highest esters hydrolysis (49.85 U) and transesterification (1.04 U) activities. Despite having the highest enzymatic activity, physical absorb MCOPs-immobilized CRL were not able to maintain its catalytic stability with more than 30% decreased in enzymatic activity during consecutive hydrolysis and transesterification activities. Meanwhile, cross-linked MCOPs-immobilized CRL demonstrated highest catalytic stability with highest enzymatic activities at the end of consecutive reactions. All the MCOPs-immobilized CRL can be easily recovered and reused through centrifugation with more than 85% of recovery rate.

Design and Preparation of Carbon Nitride-Based Amphiphilic Janus N-Doped Carbon/MoS2 Nanosheets for Interfacial Enzyme Nanoreactor

Janus amphiphilic particles have gained much attention for their important application value in areas as diverse as interfacial modification, sensors, drug delivery, optics, and actuators. In this work, we prepared Janus amphiphilic nanosheets composed of nitrogen-doped stratiform meso-macroporous carbons (NMC) and molybdenum sulfide (MoS₂) for hydrophilic and hydrophobic sides, respectively. The dicyandiamide and glucose were used as precursors for synthesizing two-dimensional nitrogen-doped meso-macroporous carbons, and the molybdate could be anchored by the functional groups on the surface of carbon layers and then transform into uniformly MoS₂ to form the Janus amphiphilic layer by layer NMC/MoS₂ support. Transmission electron microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy are used to demonstrate the successful preparation of Janus materials. As the typical interfacial enzyme, Candida rugosa lipase (CRL) immobilized on the Janus amphiphilic NMC/MoS₂ support brought forth to improvement of its performance because the Janus nanosheets can be easily attached on the oil-aqueous interface for better catalytic activity (interfacial activation of lipases). The obtained immobilized lipase (NMC/MoS₂@CRL) exhibited satisfactory lipase loading (193.1 mg protein per g), specific hydrolytic activity (95.76 U g^-1), thermostability (at 55 °C, 84% of the initial activity remained after 210 min), pH flexibility, and recyclability (60% of the initial activity remained after nine runs). In terms of its application, the esterification rate of using NMC/MoS₂@CRL (75%) is higher than those of NMC@CRL (20%) and MoS₂@CRL (11.8%) in the "oil-water" biphase and CRL as well as NMC/MoS₂@CRL in the one-phase. Comparing with the free CRL, NMC@CRL, and MoS₂@CRL, the Janus amphiphilic NMC/MoS₂ served as a carrier that exhibited more optimal performance and practicability.

Synthesis of lutein esters using a novel biocatalyst of Candida antarctica lipase B covalently immobilized on functionalized graphitic carbon nitride nanosheets

Lutein scavenges free radicals and inhibits vision damage caused by photo oxidation, while decomposing easily with light and heat. Its stability and bioavailability can be tremendously improved by lutein ester synthesis. However, green and efficient esterification preparation methods are urgently needed. In this study, which used functionalized graphitic carbon nitride nanosheets (g-C₃N₄-Ns) as the immobilized carrier, a novel biocatalyst was designed and prepared to accommodate Candida antarctica lipase B (CALB), considerably enhancing the performance. It was characterized by TEM, XRD, FTIR, XPS, TGA, and BET to demonstrate successful preparation and then applied to catalyze esterification between lutein and succinate anhydride in dimethyl formamide (DMF) solvent resulting in a conversion rate up to 92% at 50 °C in 60 h, 34% more than free CALB under the same conditions. We believe this is the highest esterification rate in lutein esters synthesis and it has great potential to facilitate eco-friendly and efficient preparation.

Production and use of immobilized lipases in/on nanomaterials: A review from the waste to biodiesel production

As a highly efficient and environmentally friendly biocatalyst, immobilized lipase has received incredible interest among the biotechnology community for the production of biodiesel. Nanomaterials possess high enzyme loading, low mass transfer limitation, and good dispersibility, making them suitable biocatalytic supports for biodiesel production. In addition to traditional nanomaterials such as nano‑silicon, magnetic nanoparticles and nano metal particles, novel nanostructured forms such as nanoflowers, carbon nanotubes, nanofibers and metal-organic frameworks (MOFs) have also been studied for biodiesel production in the recent years. However, some problems still exist that need to be overcome in achieving large-scale biodiesel production using immobilized lipase on/in nanomaterials. This article mainly presents an overview of the current and state-of-the-art research on biodiesel production by immobilized lipases in/on nanomaterials. Various immobilization strategies of lipase on various advanced nanomaterial supports and its applications in biodiesel production are highlighted. Influential factors such as source of lipase, immobilization methods, feedstocks, and production process are also critically discussed. Finally, the current challenges and future directions in developing immobilized lipase-based biocatalytic systems for high-level production of biodiesel from waste resources are also recommended.

Immobilization of Thermoalkalophilic Lipase from Bacillus atrophaeus FSHM2 on Amine-Modified Graphene Oxide Nanostructures: Statistical Optimization and Its Application for Pentyl Valerate Synthesis

Synthesis of (3-aminopropyl) triethoxysilane (APTES)-functionalized graphene oxide (GO) nanosheets, statistical optimization of conditions for immobilization of Bacillus atrophaeus lipase (BaL) on as-synthesized support, and application of the immobilized BaL for esterification of valeric acid were carried out in this investigation. The optimum specific activity of the immobilized BaL (81.60 ± 0.28 U mg^-1) was achieved at 3 mg mL^-1 of GO-NH₂, 50 mM of phosphate buffer, pH 7.0, 60 min sonication time, 100 mM glutaraldehyde, 25 U mL^-1 of enzyme, and 8 h immobilization time at 4 °C. The immobilized BaL retained about 90% of its initial activity after 10 days of storage. Moreover, about 70% of the initial activity of the immobilized BaL was retained after 10 cycles of application. The results of esterification studies exhibited that maximum pentyl valerate synthesis using the free BaL (34.5%) and the immobilized BaL (92.7%) occurred in the organic solvent medium (xylene) after 48 h of incubation at 60 °C.

A robust nanobiocatalyst based on high performance lipase immobilized to novel synthesised poly(o-toluidine) functionalized magnetic nanocomposite: Sterling stability and application

Herein, as a promising support, a magnetic enzyme nanoformulation have been designed and fabricated by a poly-o-toluidine modification approach. Owing to the magnetic nature and the existence of amine functionalized groups, the as-synthesised poly(o-toluidine) functionalized magnetic nanocomposite (Fe₃O₄@POT) was employed as potential support for Candida rugosa lipase (CRL) immobilization to explore its application in fruit flavour esters synthesis. The morphology and structure of the Fe₃O₄@POT NC were examined through various analytical tools. Hydrolytic activity assays disclose that immobilized lipase demonstrated an activity yield of 120%. It is worth mentioning that CRL#Fe₃O₄@POT showed superior resistance to extremes of temperature and pH and different organic solvents in contrast to free CRL. The magnetic behaviour of the as-synthesised NC was affirmed by alternating gradient magnetometer analysis. It was found to own facile immobilization process, enhanced catalytic performance for the immobilized form which may be stretched to the immobilization of various vital industrial enzymes. Moreover, it retained improved recycling performance. After 10 cycles of repetitive uses, it still possessed around 90% of its initial activity for the hydrolytic reaction, since the enzyme-magnetic nanoconjugate was effortlessly obtained using a magnet from the reaction system. The formulated nanobiocatalyst was selected for the esterification reaction to synthesize the fruit flavour esters, ethyl acetoacetate and ethyl valerate. The immobilized lipase successfully synthesised flavour compounds in aqueous and n-hexane media having significant higher ester yields compared to free enzyme. The present work successfully combines an industrially prominent biocatalyst, CRL, and a novel magnetic nanocarrier, Fe₃O₄@POT, into an immobilized nanoformulation with upgraded catalytic properties which has excellent potential for practical industrial implications.

Novel amphiphilic polyvinylpyrrolidone functionalized silicone particles as carrier for low-cost lipase immobilization

The high catalytic activity, specificity and stability of immobilized lipase have been attracting great interest. How to reduce the cost of support materials has always been a hot topic in this field. Herein, for the development of low-cost immobilized lipase, we demonstrate an amphiphilic polyvinylpyrrolidone (PVP) grafted on silicone particle (SP) surface materials (SP-PVP) with a rational design based on interfacial activation and solution polymerization. Meanwhile, hydrophilic pristine SP and hydrophobic polystyrene-corded silicone particles (SP-Pst) were also prepared for lipase immobilization. SP-PVP was characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and thermogravimetry. Our results indicated that the lipase loading amount on the SP-PVP composites was about 215 mg of protein per gram. In the activity assay, the immobilized lipase SP-PVP@CRL exhibited higher catalysis activity and better thermostability and reusability than SP@CRL and SP-Pst@CRL. The immobilized lipase retained more than 54% of its initial activity after 10 times of re-use and approximately trended to a steady rate in the following cycles. By introducing the interesting amphiphilic polymer to this cheap and easily obtained SP surface, the relative performance of the immobilized lipase can be significantly improved, facilitating interactions between the low-cost support materials and lipase.

Candida rugosa lipase covalently immobilized on facilely-synthesized carbon nitride nanosheets as a novel biocatalyst

The immobilization of lipase on solid supports provides a significant improvement to the stability and reusability of lipase. During immobilization, the restricted surface area and inferior separation capacity of matrix materials are crucial for obtaining high-quality immobilized lipase. Carbon nitride nanosheets (C3N4-NS) as a type of two-dimensional nanomaterial have attracted various attentions for their prominent 2D planar nanostructure, characteristic surface area, thermostability and biocompatibility. Herein, we report a rational design and fabrication of immobilized Candida rugosa lipase based on carbon nitride nanosheets (C3N4-NS) as the matrix. The synthetic C3N4-NS are characterized by transmission electron microscopy, Brunauer-Emmett-Teller gas sorptometry measurement, X-ray powder diffraction, Fourier transform infrared spectroscopy and thermogravimetric analysis. These results show that C3N4-NS possess an as-expected two-dimensional nanostructure with a large surface area of 74.374 m2 g-1. In addition, we chose glutaraldehyde-assisted covalent attachment to combine C3N4-NS and Candida rugosa lipase (CRL) via amino groups at the margins of C3N4-NS. The as-constructed immobilized lipase (C3N4-NS@CRL) exhibits satisfactory enzyme-loading (44.76 mg g-1), pH-flexibility, thermostability (after 180 min at 50 °C, 67% of the initial activity remained) and recyclability (after 10 runs, 72% of the initial activity remained). When compared with the free CRL, all experimental data indicate that C3N4-NS@CRL exhibited improved stability and enhanced practicability. To our knowledge, this is the first report of the application of carbon nitride nanosheets to enzyme immobilization.