Adsorption of Crystal Violet Dye Using Activated Carbon of Lemon Wood and Activated Carbon/Fe3O4 Magnetic Nanocomposite from Aqueous Solutions: A Kinetic, Equilibrium and Thermodynamic Study

Removal of organic contamination from wastewater using granular activated carbon modified-Polyethylene glycol: Characterization, kinetics and isotherm study

To effectively remove Diazinon (DZ), Amoxicillin (AMX), and Crystal Violet (CV) from aquatic environments, a novel granular activated carbon (GAC) modified with Polyethylene glycol 600 (PEG) was created and manufactured. The chemical properties were investigated using a variety of characteristic analyses, including FT-IR, XRD, FESEM, and N2 adsorption/desorption. The effectiveness of GAC-PEG's adsorption for the removal of DZ, AMX, and CV was assessed under a variety of conditions, including a pH of 4-9 for the solution, 0.003-0.05 g doses of adsorbent, 50-400 ppm starting concentration, and a reaction time of 5-25 min. For DZ, AMX, and CV adsorption, the maximum adsorption capacity (Qmax) was 1163.933, 1163.100, and 1150.300 mg g-1, respectively. The Langmuir isotherm described all of the data from these adsorption experiments, and the pseudo-second-order well explains all-adsorption kinetics. Most contacts between molecules, electrostatic interactions, π-π interactions, hydrogen bonding, and entrapment in the modified CAG network were used to carry out the DZ, AMX, and CV adsorption on the GAC-PEG. The retrievability of the prepared adsorbent was successfully investigated in studies up to two cycles without loss of adsorption efficiency, and it was shown that it can be efficiently separated.

Enhancing Zn (II) recovery efficiency: Bi-divalent nickel-cobalt ferrite spinel NiXCo1-xFe2O4 as a Game-changing Adsorbent-an experimental and computational study

This study presents a comprehensive investigation into NiXCo1-xFe2O4 (x = 0.5) spinel nanoparticles synthesized through a one-pot hydrothermal method using Co(NO3)2.6H2O and Ni(NO3)2.6H2O salts. XRD, FTIR, FESEM, and VSM analyses confirmed a cubic structure of NiXCo1-xFe2O4 (x = 0.5) nanoparticles without impurities. These nanoparticles exhibit efficient Zn (II) adsorption characteristics, following Langmuir isotherm and pseudo-second-order kinetics. The maximum adsorption capacity was measured to be 666.67 mg g-1 at pH = 7, with mechanisms involving both electrostatic attraction and cation exchange. Desorption studies indicate more than 75% Zn (II) recovery in an acidic environment (pH = 2) after three cycles. Computational analysis was used to validate the experimental results through Molecular Dynamics simulations, initially focusing on NiXCo1-xFe2O4 (x = 0.5). Further exploration involved variations in x at 0.25 and 0.75 to identify the optimal Ni and Co ratio in this bivalent cation spinel ferrite. Computational analyses reveal the superior performance of NiXCo1-xFe2O4 (x = 0.75) in Zn (II) removal, supported by radial distribution analysis, VdW energy, Coulombic energy, mean square displacement (MSD), root mean square displacement (RMSD), and interaction energy. This comprehensive study provides valuable insights into the adsorption behavior and structural stability of NiXCo1-xFe2O4 nanoparticles, showcasing potential applications in Zn (II) removal.

Green-Synthesized Characterization, Antioxidant and Antibacterial Applications of CtAC/MNPs-Ag Nanocomposites

The emergence of antibiotic resistance, caused by the improper use of antibiotics, is a significant challenge in combating infectious diseases, leading to millions of annual fatalities. The occurrence of antimicrobial side effects catalyzes the investigation of novel antimicrobial compounds and sources of drugs. Consequently, the research on biological activity that is conducted on plants, plant extracts, and compounds that are produced from plant components is of utmost significance. In this study, CtAC/MNPs were obtained by the reaction of activated carbon (AC) obtained from the fruits of the Celtis tournefortii (Ct) plant and magnetic nanoparticles (MNPs), and a CtAC/MNPs-Ag nanocomposite was synthesized by the reduction in silver ions added to the reaction. The synthesized CtAC/MNPs and CtAC/MNPs-Ag nanocomposites were analyzed spectroscopically (FTIR, XRD), microscopically (SEM, EDX), optically (DLS), electrochemically (zeta potential) and magnetically (VSM). The antibacterial activities of CtAC/MNPs and CtAC/MNPs-Ag nanocomposites against S. aureus and E. coli were investigated by microdilution method using minimal inhibitory concentration (MIC) and disk diffusion methods. Antioxidant activity study, including total phenolic content and DPPH and cuprac assays, revealed the remarkable effect of the CtAC/MNPs-Ag nanocomposite. This study has the advantages of obtaining CtAC/MNPs and CtAC/MNPs-Ag nanocomposites in a short time without requiring energy, and most importantly, the reaction takes place without using any toxic substances. In addition, according to the data obtained in the study, the CtAC/MNPs-Ag nanocomposite is thought to shed light on biomedical research.

Magnetized cubic zinc MOFs for efficient removal of hazardous cationic and anionic dyes in aqueous solutions

A significant amount of dye runoff and aqueous waste are released from the manufacturing process of dyes with intense and permanent colors, which are undesirable from a cultural and ecological aspect. In this paper, we present a green, simple, low-effort, and energy-efficient method of creating magnetized cubic Zn-MOFs for the adsorption and elimination of various organic dyes. Magnetic iron oxide materials with a hierarchical structure were loaded and doped into cubic zinc metal-organic frameworks (MDLZ). High magnetic characteristics, chemical stability, minimal toxicity, and ease of removing various dyes from aqueous effluents are all exhibited by the developed MDLZ adsorbent. To assess MDLZ's capacity to adsorb organic dyes from an aqueous solution, organic dyes such as Crystal Violet (CV), Neutral Red (NR), and Congo Red (CR) were used as model materials. Many adsorption factors were examined, including temperature, pH, contact time, initial concentration, and adsorbent dosage. Under optimal elimination circumstances, MDLZ was utilized to evaluate the kinetic, thermodynamic, and isotherm models for the adsorption of CR, NR, and CV dyes. The adsorption capacity (q m) of the MDLZ adsorbent at 25 °C was 39.37 mg g-1 for CV, 239.81 mg g-1 for CR, and 321.54 mg g-1 for NR, which is significantly higher than those of other adsorbents reported. The magnetized nanocubes' large surface area and uniform micropores enabled them to eliminate a large number of organic dyes from wastewater effectively, and their strong adsorption capability persisted even after four reuse cycles. The microporous MLDZ adsorbent offers a simple and effective method for handling industrial effluents and filtration of water.

Adsorption of Cd (II) ions and methyl violet dye by using an agar-graphene oxide nano-biocomposite

In this work, an agar-graphene oxide hydrogel was prepared to adsorb Cd (II) and Methyl Violet (MV) from water. The hydrogel was synthesised and characterised through SEM and EDS. Kinetic, equilibrium and regeneration studies were carried out, in which Langmuir, Freundlich and Sips isotherm models were fitted to the equilibrium experimental data; and regarding the kinetics, studies were conducted by modelling experimental data considering both empirical and phenomenological models. SEM and EDS have shown the composite present a 3D-disordered porous microstructure and that it is mainly constituted of C and O. Sips model fitted well to Cd (II) (R2 = 0.968 and χ2 =  0.176) and MV (R2 = 0.993 and χ2 =  0.783). The qmax values for MV and Cd (II) were 76.65 and 11.70 mg.g-1, respectively. Pseudo-order models satisfactorily described Cd (II) and MV adsorption kinetics with R2 > 0.90. Regeneration experiments revealed an outstanding reuse capacity of the adsorbent after three cycles of adsorption-desorption for both Cd (II) and MV. This study evidences the possibility of a feasible adsorbent for Cd (II) and MV removal from water for successive cycles of use.

Exploring the structural characteristics and dye removal capabilities of powder-, granule- and film- shaped magnetic activated carbon derived from Oleaster seed

Dye pollution in water caused by excessive discharge of industrial effluent has become a major environmental problem in recent decades because of its irreversible effects on human health. In this study, low-cost carbon-based adsorbents synthesized from Oleaster seed (OS) were prepared in three forms of powder (PAC), film (FAC), and granule (GAC) and used for the removal of methylene blue dye. The properties of the synthesized adsorbents were characterized by SEM-EDX, BET, XPS and FTIR analyses. The maximum adsorption capacity (qmax) of PAC, FAC, and GAC adsorbents were obtained as 68.49, 32.25, and 15.10 mg/g, respectively at the optimum experimental conditions of pH = 10, adsorbent dosages of 0.5, 1, and 2 g/l, contact times of 60, 90, and 120 min, dye concentration of 10 mg/L, and temperature of 25°C. The Langmuir isotherm well described the equilibrium data for all three adsorbents. The pseudo-second-order kinetic model provided the best fit with the adsorption data obtained from all three adsorbents. Adsorption occurred spontaneously through a combination of chemical and physical mechanisms, with a thermodynamically exothermic process. The desorption experiments demonstrated that all the adsorbents have substantial potential for recovery. The novel activated carbon/alginate composite films are proposed as more promising biosorbents to remove MB dye from the aquatic environment compared to GAC adsorbents.

A review on sustainable management of biomass: physicochemical modification and its application for the removal of recalcitrant pollutants-challenges, opportunities, and future directions

Adsorption is one of the most efficient methods for remediating industrial recalcitrant wastewater due to its simple design and low investment cost. However, the conventional adsorbents used in adsorption have several limitations, including high cost, low removal rates, secondary waste generation, and low regeneration ability. Hence, the focus of the research has shifted to developing alternative low-cost green adsorbents from renewable resources such as biomass. In this regard, the recent progress in the modification of biomass-derived adsorbents, which are rich in cellulosic content, through a variety of techniques, including chemical, physical, and thermal processes, has been critically reviewed in this paper. In addition, the practical applications of raw and modified biomass-based adsorbents for the treatment of industrial wastewater are discussed extensively. In a nutshell, the adsorption mechanism, particularly for real wastewater, and the effects of various modifications on biomass-based adsorbents have yet to be thoroughly studied, despite the extensive research efforts devoted to their innovation. Therefore, this review provides insight into future research needed in wastewater treatment utilizing biomass-based adsorbents, as well as the possibility of commercializing biomass-based adsorbents into viable products.

Sequestration of Pb(II) using channel-like porous spheres of carboxylated graphene oxide-incorporated cellulose acetate@iminodiacetic acid: optimization and mechanism study

The adsorption property of the costless green cellulose acetate (CA) was boosted by the dual modifications: inner modification by incorporating carboxylated graphene oxide (COOH-GO) into the CA spheres and outer modification by the surface modification of the COOH-GO@CA spheres by iminodiacetic acid (IDA) for removing Pb(II). The adsorption experiments of the Pb(II) proceeded in a batch mode to evaluate the adsorption property of the COOH-GO@CA@IDA spheres. The maximal Pb(II) adsorption capacity attained 613.30 mg/g within 90 min at pH = 5. The removal of Pb(II) reached its equilibrium within 20 min, and the removal % was almost 100% after 30 min at the low Pb(II) concentration. The Pb(II) adsorption mechanism was proposed according to the kinetics and isotherms studies; in addition, the zeta potential (ZP) measurements and X-ray Photoelectron Spectroscopy (XPS) analysis defined the adsorption pathways. By comparing the XPS spectra of the authentic and used COOH-GO@CA@IDA, it was deduced that the contributed chemical adsorption pathways are Lewis acid-base, precipitation, and complexation. The zeta potential (ZP) measurements demonstrated the electrostatic interaction participation in adsorbing the cationic Pb(II) species onto the negatively charged spheres (ZP = 14.2 mV at pH = 5). The unique channel-like pores of the COOH-GO@CA@IDA spheres suggested the pore-filling mechanism of Pb(II). The promising adsorption results and the superb recyclability character of COOH-GO@CA@IDA enable it to extend of the bench scale to the industrial scale.

Nanomaterials for sustainable remediation: efficient removal of Rhodamine B and lead using greenly synthesized novel mesoporous ZnO@CTAB nanocomposite

This study explores the dual applications of a greenly synthesized ZnO@CTAB nanocomposite for the efficient remediation of Rhodamine B (RhB) and lead (Pb). The synthesis method involves a sustainable approach, emphasizing environmentally friendly practices. FT-IR, XRD, FESEM, zeta potential, and particle size analyzer (PSA), BET, and UV-VIS were used to physically characterize the zinc oxide and CTAB nanocomposite (ZnO@CTAB). The size and crystalline index of ZnO@CTAB are 77.941 nm and 63.56% respectively. The Zeta potential of ZnO@CTAB is about - 22.4 mV. The pore diameter of the ZnO@CTAB was 3.216 nm, and its total surface area was 97.42 m2/g. The mechanism of adsorption was investigated through pHZPC measurements. The nanocomposite's adsorption performance was systematically investigated through batch adsorption experiments. At pH 2, adsorbent dose of 0.025 g, and temperature 50 °C, ZnO@CTAB removed the most RhB, while at pH 6, adsorbent dose of 0.11 g, and temperature 60 °C, ZnO@CTAB removed the most Pb. With an adsorption efficiency of 214.59 mg/g and 128.86 mg/g for RhB and Pb, the Langmuir isotherm model outperforms the Freundlich isotherm model in terms of adsorption. The pseudo-2nd-order model with an R2 of 0.99 for both RhB and Pb offers a more convincing explanation of adsorption than the pseudo-1st-order model. The results demonstrated rapid adsorption kinetics and high adsorption capacities for RhB and Pb. Furthermore, there was minimal deterioration and a high reusability of ZnO@CTAB till 4 cycles were observed.

Seeking the adsorption of tetracycline in water by Fe-modified sludge biochar at different pyrolysis temperatures

The composite material SBC-Fe-x with sludge and Fe3+ was developed by different calcination temperatures (600, 700, and 800 °C) for the removal of tetracycline (TC). The adsorption rates of SBC-Fe-600, SBC-Fe-700, and SBC-Fe-800 were 77.5%, 89%, and 91%, respectively. Furthermore, the Langmuir model indicated that the maximum adsorption capacity of SBC-Fe-700 (157.93 mg/g) was three times greater than that of SBC-Fe-600. The conclusions were confirmed by a series of characterizations that SBC-Fe-700 showed a larger specific surface area, well-developed pore structure, rich oxygen-containing functional groups and a high degree of graphitization. The results of pH experiments indicated the broad applicability of SBC-Fe-700 for TC adsorption. In addition, SBC-Fe-700 suggested outstanding performance in different water environments. This work produced a feasible adsorbent for the removal of TC, and a new direction for sludge resource utilization was proposed.

Activated carbon and their nanocomposites derived from vegetable and fruit residues for water treatment

Water pollution remains a pressing environmental issue, with diverse pollutants such as heavy metals, pharmaceuticals, dyes, and aromatic hydrocarbon compounds posing a significant threat to clean water access. Historically, biomass-derived activated carbons (ACs) have served as effective adsorbents for water treatment, owing to their inherent porosity and expansive surface area. Nanocomposites have emerged as a means to enhance the absorption properties of ACs, surpassing conventional AC performance. Biomass-based activated carbon nanocomposites (ACNCs) hold promise due to their high surface area and cost-effectiveness. This review explores recent advancements in biomass-based ACNCs, emphasizing their remarkable adsorption efficiencies and paving the way for future research in developing efficient and affordable ACNCs. Leveraging real-time communication for ACNC applications presents a viable approach to addressing cost concerns.

Highly efficient degradation of basic dyes using gold-coated nature-based supermagnetic iron oxide nanoparticles as eco-friendly nanocatalysts

Nowadays, organic dyes are prevalent components in wastewater discharges due to their extensive use in various industries, posing a significant threat to public health across different organisms. As a result, wastewater treatment has become an indispensable requirement. In this study, we synthesized supermagnetic iron oxide (Fe3O4 NPs) and gold-iron oxide bimetallic nanoparticles (Au@Fe3O4 BNPs) using an eco-friendly method that involved natural compounds extracted from brown Egyptian propolis. We employed UV-visible spectroscopy, FTIR, XRD, VSM, SEM, HRTEM, EDX, Zeta potential and XPS techniques to examine the optical characteristics, chemical structure, crystalline structure, magnetic properties, morphology, size, and chemical composition of these biosynthesized nanoparticles. Furthermore, these nanoparticles were used as nanocatalysts for the removal of cationic dyes. The photocatalytic results indicated high efficiency in the removal of methylene blue (MB), crystal violet (CV), and malachite green (MG) dyes from aqueous solutions using Fe3O4 NPs and Au@Fe3O4 BNPs. The removal rates of MB, CV, and MG were about 95.2% in 70 min, 99.4% in 50 min, and 96.2% in 60 min for Fe3O4 NPs, and 97.1% in 50 min, 99.1% in 30 min, and 98.1% in 50 min for Au@Fe3O4 BNPs, respectively. The study also assessed the potential anti-radical properties of the extract, Fe3O4 NPs, and Au@Fe3O4 BNPs using the DPPH assay, and the results demonstrated their antioxidant activity. Finally, these Fe3O4 NPs and Au@Fe3O4 BNPs have the potential to serve as efficient antioxidants and photocatalysts for removing basic dyes from water.

Ensemble meta machine learning for predicting the adsorption of anionic and cationic dyes from aqueous solutions using Polymer/graphene/clay/MgFeAl-LTH nanocomposite

Adsorption is one of the most promising wastewater treatment methods due to its simplicity and efficacy at ambient temperature and pressure. However, the technical and economic feasibility of this process largely depends on the performance of the utilized adsorbents. In this study, a promising adsorbent made of polyethyleneimine, graphene oxide (GO), bentonite, and MgFeAl-layered triple hydroxide (MgFeAl-LTH) has been synthesized and characterized. The results revealed that the synthesized nanocomposite (abbreviated as PGB-LTH) possesses good porosity and crystallinity. The adsorption performance of the PGB-LTH nanocomposite towards two harmful water pollutants (i.e., methyl orange (MO) and crystal violet (CV)) was investigated, and the results revealed that the nanocomposite outperforms its parental materials (i.e., GO, bentonite, and MgFeAl-LTH). The maximum adsorption capacity (qmax) of MO and CV onto the nanocomposite could reach 1666.7 and 1250.0 mg/g, respectively, as predicted using the Langmuir adsorption isotherm. Additionally, the PGB-LTH nanocomposite is highly reusable with an insignificant decline in performance upon repetitive use. In terms of thermodynamics, MO adsorption onto the nanocomposite is exothermic while CV adsorption is endothermic despite that both dyes adsorb spontaneously as revealed by the negative values of the Gibbs free energy change at all the examined temperatures. The generated adsorption data were utilized for constructing and assessing ensemble meta-machine learning techniques aimed at cost-effective simulation and prediction of the proposed adsorption method. Bagging and boosting methods were developed and evaluated intensively using the obtained adsorption data. The Extra Trees model achieved promising results as evidenced by the high correlation coefficient of 99% as well as low computed RMSE and MAE errors of 11.42 and 5.11, respectively, during the testing phase. These results demonstrate the model strong capability to effectively simulate and predict the adsorption process in question.

Synthesis and characterization of iron oxide-commercial activated carbon nanocomposite for removal of hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye

Iron Oxide-commercial activated carbon nanocomposite (CAC-IO) was prepared from commercial activated carbon (CAC) by the co-precipitation method, and the resulting nanocomposite was used as an adsorbent to remove hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye from wastewater. The produced materials (CAC, CAC after oxidation, and CAC-IO) were comparatively characterized using FTIR, BET, SEM, EDX TEM, VSM, and XRD techniques. The adsorption mechanism of Cr6+ ions and MV40 dye on CAC-IO was examined using Langmuir and Freundlich isotherm models.. Different models were applied to know the adsorption mechanism and it was obtained that Pseudo-second order fits the experimental data better. This means that the adsorption of the adsorbate on the nanocomposite was chemisorption. The maximum removal percent of Cr6+ ions by CAC-IO nanocomposite was 98.6% determined as 2 g L-1 adsorbent concentration, 100 mg L-1 initial pollutant concentration, solution pH = 1.6, the contact time was 3 h and the temperature was room temperature. The maximum removal percentage of Mordant Violet 40 dye (C.I. 14,745) from its solutions by CAC-IO nanocomposite was 99.92% in 100 mg L-1 of initial dye concentrations, 1.0 g L-1 of adsorbent concentration, solution pH = 2.07, the contact time was 3 h. The MV40 dye adsorption on CAC-IO was the most fitted to the Freundlich isotherm model. The maximum adsorption capacity was calculated according to the Langmuir model as 833.3 mg g-1 at 2 g L-1 of adsorbent concentration and 400 mg L-1 of initial MV40 dye concentration. The Cr6+ ions adsorption on CAC-IO was more fitted to the Freundlich model with Qmax, equal to 312.50 mg g-1 at 1 g L-1 adsorbent concentration and 400 mg L-1 of Cr6+ ions initial concentrations.

Enhanced Adsorption of Textile Dyes by a Novel Sulfonated Activated Carbon Derived from Pomegranate Peel Waste: Isotherm, Kinetic and Thermodynamic Study

The rapid growth of the dye and textile industry has raised significant public concerns regarding the pollution caused by dye wastewater, which poses potential risks to human health. In this study, we successfully improved the adsorption efficiency of activated carbon derived from pomegranate peel waste (PPAC) through a single-step and surface modification approach using 5-sulfonate-salicylaldehyde sodium salt. This innovative and effective sulfonation approach to produce sulfonated activated carbon (S-PPAC) proved to be highly effective in removing crystal violet dye (CV) from polluted water. The prepared PPAC and S-PPAC were characterized via FESEM, EDS, FTIR and BET surface area. Characterization studies confirmed the highly porous structure of the PPAC and its successful surface modification, with surface areas reaching 1180.63 m2/g and 740.75 m2/g for the PPAC and S-PPAC, respectively. The maximum adsorption capacity was achieved at 785.53 mg/g with the S-PPAC, an increase of 22.76% compared to the PPAC at 45 °C. The isothermic adsorption and kinetic studies demonstrated that the adsorption process aligned well with the Freundlich isotherm model and followed the Elovich kinetic model, respectively. The thermodynamic study confirmed that the adsorption of CV dye was endothermic, spontaneous and thermodynamically favorable onto PPAC and S-PPAC.

Enhanced copper (II) bioremediation from wastewater using nano magnetite (Fe3O4) modified biochar of Ascophyllum nodosum

Despite the remarkable Cu(II) sorption biochar potential, it is challenging to desorb them for repeated biochar usage. The present study aims to develop engineered biochar by polarizing Ascophyllum nodosum (seaweed) biomass and magnetizing it with Fe3O4 nanoparticles coating. SEM, EDX, XRD, BET, and FT-IR helped to characterize engineered biochar. Unlike conventional, magnetite biochar exhibited a significant Cu(II) removal potential from an aqueous solution at pH 5. The native and magnetic biochar removal efficiency was 75.2 % (36.99 mgg-1) and 90.27% (45.13 mgg-1), respectively. No significant change in temperature effect was observed. Adsorption study showed that magnetic biochar followed the Langmuir isotherm model with Qmax 53.19 mgg-1. Adsorption kinetics study indicates that magnetic biochar chemisorption dominates over physisorption. Thus, this study shows that seaweed-derived modified biochar could be the best alternative bioresource for removing heavy metals from wastewater. It can be reused to reduce the overall treatment cost of the process.

Biogenic adsorbents for removal of drugs and dyes: A comprehensive review on properties, modification and applications

This comprehensive review explores the potential and versatility of biogenic materials as sustainable and environmentally benign alternatives to conventional adsorbents for the removal of drugs and dyes. Biogenic adsorbents derived from plants, animals, microorganisms, algae and biopolymers have bioactive compounds that interact with functional groups of pollutants, resulting in their binding with the sorbent. These materials can be modified mechanically, thermally and chemically to enhance their adsorption properties. Biogenic hybrid composites, which integrate the characteristics of more than one material, have also been fabricated. Additionally, microorganisms and algae are analyzed for their ability to uptake pollutants. Various influential factors that contribute to the adsorption process are also discussed. The challenge, limitations and future prospects for research are reviewed and bridging gap between large scale application and laboratory scale. This comprehensive review, involves a combination of various biogenic adsorbents, going beyond the existing literature where typically only specific adsorbents are reported. The review also covers the isotherms, kinetics, and desorption studies of biogenic adsorbents, providing an improved framework for their effective use in removing pharmaceuticals and dyes from wastewater.

Utilizing Novel Lignocellulosic Material from Hart's-Tongue Fern (Asplenium scolopendrium) Leaves for Crystal Violet Adsorption: Characterization, Application, and Optimization

In this work, a new lignocellulosic adsorbent was obtained and tested for crystal violet dye removal from water. The material was obtained from hart's-tongue fern (Asplenium scolopendrium) leaves after minimal processing, without chemical or thermal treatment. The surface of the material was characterized using a variety of techniques, including FTIR, SEM, and color analysis. The effect of various factors on the adsorption capacity was then investigated and discussed. The kinetic and equilibrium studies showed that the general-order kinetic model and the Sips isotherm are the most suitable to describe the adsorption process. The equilibrium time was reached after 20 min and the maximum calculated value of the adsorption capacity was 224.2 (mg g-1). The determined values for the thermodynamic parameters indicated physical adsorption as the main mechanism involved in the process. The Taguchi method was used to optimize the adsorption conditions and identify the most influential controllable factor, which was pH. ANOVA (general linear model) was used to calculate the percentage contribution of each controllable factor to dye removal efficiency. Analysis of all the results shows that hart's-tongue fern (Asplenium scolopendrium) leaves are a very inexpensive, readily available, and effective adsorbent for removing crystal violet dye from aqueous solutions.

Optimization and mechanistic approach for removal of crystal violet and methylene blue dyes via activated carbon from pyrolyzed-ZnCl2 bamboo waste

In this study, bamboo waste (BW) was subjected to pyrolysis-assisted ZnCl2 activation to produce mesoporous activated carbon (BW-AC), which was then evaluated for its ability to remove cationic dyes, specifically methylene blue (MB) and crystal violet (CV), from aqueous environments. The properties of BW-AC were characterized using various techniques, including potentiometric-based point of zero charge (pHpzc), scanning electron microscopy with energy dispersive X-rays (SEM-EDX), X-ray diffraction (XRD), gas adsorption with Brunauer-Emmett-Teller (BET) analysis, infrared (IR) spectroscopy. To optimize the adsorption characteristics (BW-AC dosage, pH, and contact time) of PBW, a Box-Behnken design (BBD) was employed. The BW-AC dose of 0.05 g, solution pH of 10, and time of 8 min are identified as optimal operational conditions for achieving maximum CV (89.8%) and MB (96.3%) adsorption according to the BBD model. The dye removal kinetics for CV and MB are described by the pseudo-second-order model. The dye adsorption isotherms revealed that adsorption of CV and MB onto BW-AC follow the Freundlich model. The maximum dye adsorption capacities (qmax) of BW-AC for CV (530 mg/g) and MB (520 mg/g) are favorable, along with the thermodynamics of the adsorption process, which is characterized as endothermic and spontaneous. The adsorption mechanism of CV and MB dyes by BW-AC was attributed to multiple contributions: hydrogen bonding, electrostatic forces, π-π attraction, and pore filling. The findings of this study highlight the potential of BW-AC as an effective adsorbent in wastewater treatment applications, contributing to the overall goal of mitigating the environmental impact of cationic dyes and ensuring the quality of water resources.

Production of activated carbon from food wastes (chicken bones and rice waste) by microwave assisted ZnCl2 activation: an optimized process for crystal violet dye removal

A major worldwide challenge that presents significant economic, environmental, and social concerns is the rising generation of food waste. The current work used chicken bones (CB) and rice (R) food waste as alternate precursors for the production of activated carbon (CBRAC) by microwave radiation-assisted ZnCl2 activation. The adsorption characteristics of CBRAC were investigated in depth by removing an organic dye (crystal violet, CV) from an aquatic environment. To establish ideal conditions from the significant adsorption factors (A: CBRAC dosage (0.02-0.12 g/100 mL); B: pH (4-10); and C: duration (30-420), a numerical desirability function of Box-Behnken design (BBD) was utilized. The highest CV decolorization by CBRAC was reported to be 90.06% when the following conditions were met: dose = 0.118 g/100 mL, pH = 9.0, and time = 408 min. Adsorption kinetics revealed that the pseudo-first order (PFO) model best matches the data, whereas the Langmuir model was characterized by equilibrium adsorption, where the adsorption capacity of CBRAC for CV dye was calculated to be 57.9 mg/g. CV adsorption is accomplished by several processes, including electrostatic forces, pore diffusion, π-π stacking, and H-bonding. This study demonstrates the use of CB and R as biomass precursors for the efficient creation of CBRAC and their use in wastewater treatment, resulting in a greener environment.

Mathematical Modelling and Optimization for Facile Synthesis of Structured Activated Carbon (ACs) from Adansonia kilima (Baobab) Wood Chips Integrating Microwave-Assisted Pyrolysis for the Elimination of Lead (II) Cations from Wastewater Effluents

In this research, activated carbon (AC) was synthesized from ligno-cellulosic residues of Adansonia kilima (Baobab) wood chips (AKTW) using two-step semi-carbonization and subsequent pyrolysis using microwave-induced heating (MWP) in the presence of a mild activating agent of K2CO3. The influence of process input variables of microwave power (x1), residence time (y1), and amount of K2CO3 (z1) were analysed to yield superior quality carbon having maximum removal efficiencies (R1) for lead (II) cations from waste effluents, fixed carbon percentages (R2), and carbon yield percentages (R3). Analysis of variance (ANOVA) was used to develop relevant mathematical models, with an appropriate statistical assessment of errors. Level factorial response surface methodology (RSM) relying on the Box-Behnken design (BBD) was implemented for the experimental design. The surface area and porous texture of the samples were determined using Brunauer, Emmett, and Teller (BET) adsorption/desorption curves based on the N2 isotherm. Surface morphological structure was observed using field emission scanning electron microscopic (FESEM) analysis. Thermogravimetric analysis (TGA) was carried out to observe the thermal stability of the sample. Change in the carbon content of the samples was determined using ultimate analysis. X-ray diffraction (XRD) analysis was performed to observe the crystalline and amorphous texture of the samples. The retention of a higher proportion of fixed carbon (80.01%) ensures that the synthesized adsorbent (AKTWAC) will have a greater adsorption capacity while avoiding unwanted catalytic activity for our synthesized final sample.

Sustainable approach for adsorptive removal of cationic and anionic dyes by titanium oxide nanoparticles synthesized biogenically using algal extract ofSpirulina

Worldwide, dyes are significant pollutants present in water because of their huge consumption for industrial purposes. These dyes as pollutants cause serious health issues in human beings and cause the loss of aquatic biodiversity. So, remediation of pollutants like dyes from wastewater is the need of the hour. In the present study, we greenly synthesizedSpirulina-mediated titanium oxide nanoparticles (STONPs) for the adsorptive remediation of methyl orange (MO) (anionic) and malachite green (MG) (cationic) dyes. The characterization of STONPs was performed by Field emission scanning electron microscopy (FESEM) with EDX, FT-IR, XRD, Zeta Potential and particle size analyzer, Raman spectroscopy, and UV-vis. The various parameter effects like pH, nano-adsorbent dose, the concentration of dye, contact time, and temperature were also examined. Adsorption isotherms like Langmuir, Freundlich, and Temkin, and Kinetics models like Elovich Model, Pseudo 1st, intraparticle diffusion model (IPDM), Pseudo 2nd order, and the thermodynamic model were applied for a stronger interpretation. Theqmaxattained utilizing the Langmuir adsorption model was 272.4795 mg g-1and 209.6436 mg g-1for MO and MG correspondingly. The regeneration study of synthesized nanomaterials up to five cycles was also done. We found that greenly synthesized STONPs have great potential for adsorptive remediation for both MG and MO dyes.

Thermoplastic starch (TPS)-based composite films for wastewater treatment: synthesis and fundamental characterization

Modification of starch is a potential basic research aiming to improve its water barrier properties. The general purpose of this study is to manufacture cross-linked iodinated starch citrate (ISC) with a degree of substitution (DS) ≈ 0.1 by modifying native corn starch with citric acid in the presence of iodine as an oxidizing agent. Thermoplastic starch (TPS) was generated with urea as a plasticizer and blended with various concentrations of ISC of (2, 4, 6%) (wt/wt) to obtain (UTPS/ISC₂, UTPS/ISC₄, and UTPS/ISC₆). Nanocomposite film was formed from UTPS/ISC₂ in presence of stabilized iodinated cellulose nanocrystals UTPS/ISC₂/SICNCs via gelatinization at a temperature of 80ºC. Water solubility and water vapor release were studied amongst the water barrier features. The fabricated starch-based composite films were evaluated utilizing Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electronic Microscope analysis (SEM), surface area, and tensile measurements. The adsorption of crystal violet (CV) dye onto produced samples was examined in an aqueous solution. The findings revealed that the UTPS/ISC₂/ISCNCs has 83% crystal violet elimination effectiveness. Moreover, the adsorption isotherms were assessed and figured out to vary in the order of Langmuir > Temkin > Freundlich > Dubinin-Radushkevich.

Iron-Iron Oxide Core-Shell Nanochains as High-Performance Adsorbents of Crystal Violet and Congo Red Dyes from Aqueous Solutions

The main aim of this work was to use the iron-iron oxide nanochains (Fe NCs) as adsorbents of the carcinogenic cationic crystal violet (CV) and anionic Congo red (CR) dyes from water. The investigated adsorbent was prepared by a magnetic-field-induced reduction reaction, and it revealed a typical core-shell structure. It was composed of an iron core covered by a thin Fe₃O₄ shell (<4 nm). The adsorption measurements conducted with UV-vis spectroscopy revealed that 15 mg of Fe NCs constituted an efficient dose to be used in the CV and CR treatment. The highest effectiveness of CV and CR removal was found for a contact time of 90 min at pH 7 and 150 min at pH 8, respectively. Kinetic studies indicated that the adsorption followed the pseudo-first-order kinetic model. The adsorption process followed the Temkin model for both dyes taking into account the highest value of the R² coefficient, whereas in the case of CR, the Redlich-Peterson model could be also considered. The maximal adsorption capacity estimated from the Langmuir isotherms for the CV and CR was 778.47 and 348.46 mg g^-1, respectively. Based on the Freundlich model, both dyes adsorbed on the Fe NCs through chemisorption, but Coulombic interactions between the dye and adsorbent cannot be excluded in the case of the CV dye. The obtained results proved that the investigated Fe NCs had an excellent adsorption ability for both dye molecules within five cycles of adsorption/desorption, and therefore, they can be considered as a promising material for water purification and environmental applications.

Kinetics and Isotherm Studies for Adsorption of Gentian Violet Dye from Aqueous Solutions Using Synthesized Hydroxyapatite

Water is the most important resource for life, but it has been greatly exhausted over the past century as a result of the human population and environmentally harmful activities. The excessive quantity of dyes exists in the wastewater produced from the textile industries which is the main reason for serious human health and environmental problems. There are many dye removal techniques, and the most promising one is the adsorption technique. The novelty of this research is using unmodified synthesized hydroxyapatite (HAp) as an adsorbent for the removal of gentian violet (GV) dye from aqueous solutions as there are no sufficient data in the literature about using it in the adsorption of GV dye from aqueous solutions. Unmodified HAp was synthesized by a combined precipitation microwave method. The prepared adsorbent was characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and zeta potential analyses. The kinetic study showed that the pseudo-second-order (PSO) model was the best fitted model with the experimental data. Analysis of adsorption isotherms using different models showed that this adsorption system was better described by the Halsey isotherm with a maximum adsorption capacity (q_max)  of 1.035 mg/g. The effects of experimental factors such as initial solution pH, initial dye concentration, adsorbent dose, and contact time were studied during the investigation of GV dye removal efficiency. The experimental results indicated that the maximum adsorption efficiency (99.32%) of the GV dye using HAp adsorbent was achieved at the following conditions: contact time = 90 min, pH = 12, initial GV dye concentration = 3 mg/L, and adsorbent dose = 1 g/L. The adsorption mechanism of the GV dye using HAp might be explained by the electrostatic interaction between the negatively charged surface of the HAp and the positively charged group of the GV dye. Thermodynamics study was performed on the adsorption process of GV dye from aqueous solutions using the synthesized HAp which revealed that this process was endothermic and spontaneous due to positive values of ΔH and ΔS and negative values of ΔG.

Magnetite carboxymethylcellulose as biological macromolecule-based absorbent for cationic dyes removal from environmental samples

In this study, magnetite carboxymethylcellulose (CMC@Fe₃O₄) composite as magnetic biological molecules were synthetized for the use as adsorbent to remove four types of cationic dyes, namely Methylene Blue, Rhodamine B, Malachite Green, and Methyl Violet from aqueous solution. The characteristic of the adsorbent was achieved by Fourier Transform Infrared Spectroscopy, Field Emission Scanning Electron Microscope (FESEM), X-ray Diffraction, Vibrating Sample Magnetometer and Thermal Gravimetric Analysis techniques. Besides, essential influencing parameters of dye adsorption; the solution pH, solution temperature, contact time, adsorbent concentration and initial dye dosage were studied. FESEM analysis showed the magnetic Fe₃O₄-TB, Fe₃O₄@SiO₂, Fe₃O₄@SiO₂-NH₂ and CMC@Fe₃O₄ composites were in spherical shape, with average size of 43.0 nm, 92.5 nm, 134.0 nm and 207.5 nm, respectively. On the saturation magnetization (Ms), the results obtained were 55.931 emu/g, 34.557 emu/g, 33.236 emu/g and 11.884 emu/g. From the sorption modelling of Isotherms, Kinetics, and Thermodynamics, the adsorption capacity of dyes is (MB = 103.33 mg/g), (RB = 109.60 mg/g), (MG = 100.08 mg/g) and (MV = 107.78 mg/g). With all the adsorption processes exhibited as exothermic reactions. The regeneration and reusability of the synthetized biological molecules-based adsorbent was also assessed.

A Thorough Examination of the Solution Conditions and the Use of Carbon Nanoparticles Made from Commercial Mesquite Charcoal as a Successful Sorbent for Water Remediation

Water pollution has invaded seas, rivers, and tap water worldwide. This work employed commercial Mesquite charcoal as a low-cost precursor for fabricating Mesquite carbon nanoparticles (MUCNPs) using a ball-milling process. The scanning electron energy-dispersive microscopy results for MUCNPs revealed a particle size range of 52.4-75.0 nm. The particles were composed mainly of carbon with trace amounts of aluminum, potassium, calcium, titanium, and zinc. The X-ray diffraction peaks at 26.76 and 43.28 2θ° ascribed to the (002) and (100) planes indicated a crystalized graphite phase. Furthermore, the lack of FT-IR vibrations above 3000 cm^-1 showed that the MUCNPs were not functionalized. The MUCNPs' pore diameter, volume, and surface area were 114.5 Ǻ, 0.363 cm³ g^-1, and 113.45 m² g^-1. The batch technique was utilized to investigate MUCNPs' effectiveness in removing chlorohexidine gluconate (CHDNG) from water, which took 90 min to achieve equilibrium and had an adsorption capacity of 65.8 mg g^-1. The adsorption of CHDNG followed pseudo-second-order kinetics, with the rate-limiting step being diffusion in the liquid film. The Langmuir isotherm dominated the CHDNG adsorption on the MUCNPs with a correlation coefficient of 0.99. The thermodynamic studies revealed that CHDNG adsorption onto the MUCNPs was exothermic and favorable, and its spontaneity increased inversely with CHDNG concentration. The ball-milling-made MUCNPs demonstrated consistent efficiency through regeneration-reuse cycles.

Physico-chemical, structural, and adsorption properties of amino-modified starch derivatives for the removal of (in)organic pollutants from aqueous solutions

In this study, an environmentally sustainable process of crystal violet, congo red, methylene blue, brilliant green, Pb²⁺, Cd²⁺, and Zn²⁺ ions adsorption from aqueous solutions onto amino-modified starch derivatives was investigated. The degree of substitution, elemental analysis, swelling capacity, solubility, and FTIR, XRD, and SEM techniques were used to characterize the adsorbents. The influence of pH, contact time, temperature, and initial concentration has been studied to optimize the adsorption conditions. The amino-modified starch was the most effective in removing crystal violet (CV) (65.31-80.46 %) and Pb²⁺ (67.44-80.33 %) within the optimal adsorption conditions (pH 5, 10 mg dm^-3, 25 °C, 180 min). The adsorption of CV could be described by both Langmuir and Freundlich adsorption isotherms, while the adsorption of Pb²⁺ ions was better described by the Langmuir isotherm. The pseudo-second order model can be used to describe the adsorption kinetics of CV and Pb²⁺ on all tested samples. The thermodynamic study indicated that the adsorption of CV was exothermic, while the Pb²⁺ adsorption was endothermic. The simultaneous removal of CV and Pb²⁺ from the binary mixture has shown their competitive behavior. Thus, the amino-modified starch is a promising eco-friendly adsorbent for the removal of dyes and heavy metals from polluted water.

Supporting nanoscale zero-valent iron onto shrimp shell-derived N-doped biochar to boost its reactivity and electron utilization for selenite sequestration

Nanoscale zero-valent iron (nZVI) has been widely used in the reductive removal of contaminants from water, yet it still fights against the inherent passive cover and the raise of medium pH. In this study, nZVI was supported onto a nitrogen-doped biochar (NBC) that was prepared by pyrolyzing shrimp shell for efficiently sequestrating aqueous selenite (Se(IV)). The resultant composite (NBC-nZVI) revealed a higher reactivity and electron utilization efficiency (EUE) than the bare nZVI in Se(IV) sequestration because of the positive charge, the buffering effect and the good conductivity of NBC. The kinetic rate and EUE of NBC-nZVI were increased by 143.4% and 15.3% compared to the bare nZVI, respectively, at initial pH of 3.0. The high removal capacity of 605.4 mg g^-1 for NBC-nZVI was obtained at Se(IV) concentration of 1000 mg L^-1, initial pH of 3.0, NBC-nZVI dosage of 1.0 g L^-1 and contact time of 12 h. Moreover, NBC-nZVI exhibited a strong tolerance to solution pHs and coexisting compounds (e.g., humic acid) and could reduce the Se(IV) concentration from 5.0 mg L^-1 to below the limit of drinking water (50 μg L^-1) in real-world samples. This work exemplified a utilization of shrimp shell-derived NBC to simultaneously enhance the reactivity and EUE of nZVI for reductively removing contaminants.

Simple adsorptive removal of crystal violet, a triarylmethane dye, from synthetic wastewater using Fe (III)-treated pine needle biochar

Untreated and Fe (III)-treated pine needle biochar (PNB) were evaluated at different pH for the removal of toxic crystal violet (CV) dye from synthetic wastewaters. Adsorption kinetics followed the pseudo-first-order kinetics involving intra-particle diffusion process. The adsorption rate constant increased with Fe treatment of PNB especially at pH 7.0. Adsorption data of CV conformed well to Freundlich adsorption isotherms and both adsorption capacity (ln K) and order of adsorption (1/n) of CV were nearly doubled with Fe (III) treatment of PNB at pH 7.0. Desorption of adsorbed CV from both untreated and Fe (III)-treated PNB could be accounted satisfactorily by third-degree polynomial equations. An increase in ionic strength and temperature enhanced dye adsorption onto untreated and Fe (III)-treated PNB. Adsorption of CV was an endothermic and spontaneous reaction with an increase in entropy of the system. FTIR spectra revealed that C = O of carboxylic acid aryls and C = O and C-O-C in lignin residues of PNB reacted with Fe (III) besides the formation of some iron oxyhydroxide minerals. The changes in FTIR confirmed the possible bonding of positively charged moiety of CV with the untreated and Fe-treated PNB. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) revealed the porous surfaces of PNB with clear accumulation of Fe (III) after treatment and deposition of CV dye on surfaces and pores of PNB. Iron (III)-treated PNB at pH 7.0 can serve as an ecofriendly and cost-effective adsorbent for the efficient removal of CV dye from wastewaters.

Fe3O4-multiwalled carbon nanotubes-bentonite as adsorbent for removal of methylene blue from aqueous solutions

The contamination of water due to present of dyes, poses serious health problems. Therefore, treatment of contaminated water is necessary to resolve this problem. A tailored co-precipitation technique has been successfully used to prepare Fe₃O₄-multiwalled Carbon Nanotubes (MWCNTs)-Bentonite nanocomposite. The methylene blue present in aqueous solutions was removed using synthesized nanocomposite as adsorbent. The synthesized novel nanocomposite was analyzed by various characterization techniques. The scanning electron microscope analysis shows that Bentonite and Fe₃O₄ nanoparticles are well decorated with the MWCNTs matrix. The nanocomposite exhibited a high BET surface area of 204.01 m²/g with a pore volume of 0.367 cm³/g. The BJH adsorption average pore diameter was analyzed to be 7.2 nm. Moreover, the adsorption model was in agreement with the Redlich-Peterson model with adsorption capacity of 48.2 mg/g with a high nonlinear regression coefficient (R² = 0.985) and a low chi-square value (χ² = 6.18). Kinetics data were described well by pseudo-first-order and pseudo second order, models with a high non-linear regression coefficient (R² = 0.993). Adsorption of MB dye was determined to be a non-spontaneous and endothermic process since the values of ΔG, and ΔH were positive, and the entropy value was negative. Thus, the synthesized nanocomposite established itself as a promising candidate for the water treatment process.

Origanum vulgare manganese ferrite nanocomposite: An advanced multifunctional hybrid material for dye remediation

The purpose of the study was to fabricate sustainable and cost-effective material for the thorough cleansing of polluted water. In this context, an economical, phytogenic and multifunctional Origanum vulgare plant-based nanocomposite material, MnFe₂O₄/OV, was prepared via one-pot synthetic technique. The synthesized nanocomposite with a band gap of 2.02 eV behaved as an efficient nano-photocatalyst for the degradation of both cationic (crystal violet) and anionic (congo red) dyes under direct sunlight irradiation. The material also inhibited the growth of E. coli and S. aureus bacteria and simultaneously adsorbed both cationic and anionic dyes from water through adsorption. A variety of techniques have been used to characterize the nanocomposite, including X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and transmission electron microscopy (TEM). Additionally, the kinetics of photodegradation of the aforementioned organic dyes has also been investigated. The MnFe₂O₄/OV exhibited excellent photocatalytic performance, leading to 43% and 72% degradation within 3 h at rate constants of 2.0 × 10^-3 min^-1 and 6.0 × 10^-3 min^-1 for crystal violet and congo red, respectively. The crystal violet and congo red were used to testify to the composite's potential for adsorption under the influence of several process variables, including initial solution pH, contact time, temperature, initial dye concentration, and amount of MnFe₂O₄/OV. The Langmuir maximum adsorption capacity Q_max as in the range 14.06-14.59 mgg^-1 for crystal violet and 34.45-23.93 mgg^-1 for congo red at pH 7 within 90 min contact time in the temperature range of 30-50 °C. The phenomenon of adsorption was found feasible and endothermic at all the investigated temperatures. Also, E. coli and S. Aureus bacteria have shown growth suppression activity when exposed to MnFe₂O₄/OV.As a result, the synthesized nanocomposite, MnFe₂O₄/OV, proved to be an antimicrobial, multifunctional novel nanocomposite, which is in high demand, and could serve as an affordable, and sustainable material for comprehensive water filtration.

Adsorption of crystal violet on activated bamboo fiber powder from water: preparation, characterization, kinetics and isotherms

Biomass-activated carbon has made a great contribution as an adsorbent in the field of dye wastewater treatment. In this study, the response surface method (RSM) based on the Box-Behnken design was used to optimize the preparation process. Bamboo fiber activated carbon (BAC) with a specific surface area of 2892 m² g^-1 and a pore volume of 1.80 cm³ g^-1 was prepared. Various characterization methods (SEM, XPS, XRD, and Raman spectroscopy) were used to analyze the micro-structure of BAC. In the microscopic state, the BAC is fibrous and maintains the originally connected pores of the bamboo fiber. After high-temperature activation, the microcrystallinity of BAC decreases, and the degree of graphitization is low, indicating the presence of amorphous carbon. The adsorption capacity of BAC to crystal violet in simulated wastewater was evaluated via an adsorption experiment. Under the following conditions: the dosage of BAC was 0.04 g, the concentration was 600 mg L^-1, the adsorption temperature and time were 25 °C and 30 min, respectively, and the as-prepared BAC had a 99.96% removal rate. The adsorption process conformed to the pseudo-second-order kinetic model and Langmuir adsorption isotherm model, indicating that the adsorption process of CV on BAC belonged to monomolecular layer adsorption. The adsorption process occurs spontaneously and is accompanied by heat release, and the maximum adsorption capacity of BAC within a given concentration range could reach 1353.09 mg g^-1. SEM-EDS characterization before and after adsorption showed that ion exchange and the presence of oxygen-containing functional groups played an important role in promoting the adsorption process. The results show that BAC considerably affects CV removal, which has great application prospects.

Adsorption of Anionic and Cationic Dyes on Activated Carbon Prepared from Oak Cupules: Kinetics and Thermodynamics Studies

In this study, activated carbon produced from oak cupules (ACOC) was prepared using chemical activation with H3PO4. ACOC is subsequently used as an adsorbent to facilitate the removal of an acidic dye, naphthol blue black (NBB), and basic dye crystal violet (CV) from aqueous solutions. The ACOC was characterized by FTIR spectroscopy, XRD, and SEM. The adsorption isotherm data fits well with the Langmuir model for NBB and CV. The kinetic models of adsorption of NBB and CV by ACOC were pseudo-first order and pseudo-second order, respectively. Thermodynamic parameters were evaluated and indicated that the adsorption of both dyes onto ACOC was endothermic and spontaneous. The adsorption capacity of ACOC reached 208 mg g-1 for NBB and 658 mg g-1 for CV. ACOC was shown to be a promising adsorbent for the removal of NBB and CV from aqueous solutions.

Photocatalytic degradation of dyes by novel electrospun nanofibers: A review

Textile industry is a significant contributor of wastewater, which contains pollutants including dye and other chemical substances. The release of thousands of tons of dye used in textile processing and finishing into natural streams and aquatic bodies present dire harm to the environment. In response to environmental concerns, a number of research have been done using low-cost technology to produce absorbents that can remove dyes from water bodies. Distinct techniques such as adsorption, enzymatic and photocatalytic degradation, etc. have been employed to remove dyes. In the last few decades, photocatalysis, a simple and green strategy, has emerged as the most valuable and recent principle that deals with wastewater treatment, using uniquely fabricated nanomaterials. Among them, rapid and versatile electrospinning methods have been used for the construction of a large surface area, hierarchical and reusable nanofibers for environmental remediation. As a flexible and fast fabrication method, reviewing the use of electrospun photocatalytic nanofibers, influential parameters in electrospinning and their effectiveness in the generation of oxidizing agents are a promising platform for the fabrication of novel nanomaterials in photocatalytic degradation of dyes. This review discusses techniques for dye removal, electrospun nanofibers, their fabrication and application in photocatalysis; mechanism of photocatalytic degradation, and challenges and suggested remedies for electrospun nanofibers in photocatalysis.

Cellulose-based hydrogel for adsorptive removal of cationic dyes from aqueous solution: isotherms and kinetics

The development of economic and recyclable adsorbents for removing pollutants from contaminated water is gaining increasing attention. Agro residue or nature-based material sourced absorbents could revolutionize the future of wastewater treatment. Hence in this study, nanocellulose was synthesized from coconut husk fiber and immobilized onto chitosan to form hydrogel beads. The BET surface area and zeta potential of the adsorbent nanocrystalline cellulose-chitosan hydrogel (NCC-CH) bead was 25.77 m² g^-1 and +50.6 mV, respectively. The functional group analysis also confirmed that the adsorbent had functional groups appropriate for the adsorption of textile dyes. The adsorption performance of NCC-CH and also the influence of initial dye concentration, adsorbent dose, pH, and contact time was evaluated by batch adsorption studies with crystal violet (CV) and methylene blue (MB) dyes. The most favorable operational conditions achieved through I-optimal design in response surface methodology were 0.5 g NCC-CH, 1 h, 9 pH, and 60 mg L^-1 for CV removal (94.75%) and 0.13 g NCC-CH, 1 h, 9 pH, and 30 mg L^-1 for MB removal (95.88%). The polynomial quadratic model fits the experimental data with an R ² value of 0.99 and 0.98 for CV and MB removal, respectively. The optimum depiction of the isotherm data was obtained using the Freundlich model for MB adsorption and Freundlich and Langmuir model for CV adsorption. The Dubinin-Radushkevich (D-R) isotherm was also a good fit to the adsorption of CV and MB dye, suggesting the physisorption due to its free energy of adsorption < 8 kJ mol^-1. The kinetics were effectively explained by a pseudo-second order model for both the dyes suggesting that chemical mechanisms influenced the adsorption of CV and MB dyes onto NCC-CH. The intraparticle diffusion model best suited the MB adsorption with three stages rather than the CV with a single step process. Also, the removal efficiency of adsorbent was retained at above 60% even after seven adsorption-desorption cycles indicating the effectiveness of the NCC-CH hydrogel beads for the removal of textile dyes.

Bamboo cellulose-derived activated carbon aerogel with controllable mesoporous structure as an effective adsorbent for tetracycline hydrochloride

Activated carbon has been widespread applied in the removal of pollutants in wastewater. However, many biomass-derived activated carbon suffer from the challenge of controllable pore size regulation, hindering their efficient adsorption of pollutants. Herein, bamboo-derived activated carbon aerogel (BACA) has been successfully prepared through KOH high-temperature activation of cellulose aerogel which was prepared using cellulose extracted from bamboo. Bamboo cellulose aerogel provides sufficient reaction sites for KOH, which is conducive to the formation of a mass of mesoporous structures on the pore walls of the activated carbon aerogel. The optimal BACA adsorbent shows high specific surface area (2503.80 m²/g), and maximum adsorption capability for tetracycline hydrochloride (TCH) reaches 863.8 mg/g at 30 ℃. The removal efficiencies of TCH are 100% and 98.4% at 40 ℃ when the initial concentrations are 500 and 700 mg/L, respectively. Adsorption kinetics and isotherm indicate that the adsorption of BACA for TCH is monolayer adsorption based on chemical adsorption. Spontaneous and endothermic adsorption processes are proved by adsorption thermodynamic studies. Additionally, coexisting ions have insignificant effect on TCH adsorption, and the BACA sample displays excellent adsorption property for five reuse cycles with a removal efficiency of 80.95%, indicating the outstanding adsorption capacity of BACA in practical application. The excellent adsorption performance provides BACA with a promising perspective to remove TCH from wastewater, and the prepared method of BACA can be widely extended to other biomass materials.

Adsorptive removal of crystal violet from wastewater using sodium alginate-gelatin-montmorillonite ternary composite microbeads

In this study, the performance of the montmorillonite-filled sodium alginate/gelatin (SA-GEL-MMT) ternary biocomposite microbeads on the adsorptive removal of crystal violet (CV) dye was investigated. Firstly, the composites containing different weight ratios of MMT such as 10 %, 15 %, and 20 % were prepared. The composite beads were cross-linked using a calcium chloride (3%wt/v) solution. To determine the optimum sorption conditions the studies were performed at different parameters namely temperature, pH, contact time, sorbent dose, and dye concentration. From the sorption studies, the maximum capacity of the microbeads was found as 1000.0 mg/g whereas the maximum removal of the dye was 92.1 % at pH = 7 and a temperature of 25 °C. Additionally, the kinetic studies showed that the sorption of the dye followed the pseudo-second-order kinetics. Moreover, the adsorptive removal of the dye occurs spontaneously. This study suggests that the use of SA-GEL-MMT can be highly effective and reusable for the treatment of wastewater.

Graphene oxide supported sulfidated nano zero-valent iron (S-nZVI@GO) for antimony removal: The role of active oxygen species and reaction mechanism

Sulfidated nano zero-valent iron (S-nZVI) was used to remove various pollutants from wastewater. However, the instability, poor dispersibility, and low electron transfer efficiency of S-nZVI limit its application. Herein, graphene oxide supported sulfidated nano zero-valent iron (S-nZVI@GO) was successfully synthesized using graphene oxide (GO) as a carrier. The properties of S-nZVI@GO were characterized by scanning electron microscopy coupled to X-ray photoelectron spectroscopy (SEM-EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) concerning the surface morphology, crystalline structure, and elemental components. S-nZVI@GO displayed an excellent capacity for antimony (Sb) removal under aerobic conditions (96.7%), with a high adsorption capacity (Q_max = 311.75 mg/g). It maintained a high removal rate (over 90%) during a wide pH range (3-9). More importantly, S-nZVI@GO activated the molecular oxygen in water via a single-electron pathway to produce •O₂－ and H₂O₂, and then oxidized trivalent antimony (Sb(III)) to pentavalent antimony (Sb(V)) and further separated it by synergistic adsorption and co-precipitation. Therefore, S-nZVI@GO shows excellent potential for Sb contamination remediation.

Biocarbons Obtained from Fennel and Caraway Fruits as Adsorbents of Methyl Red Sodium Salt from Water System

The aim of this study was to prepare biocarbons by biomass activation with carbon(IV) oxide. Fennel and caraway fruits were used as the precursors of bioadsorbents. The impact of the precursor type and temperature of activation on the physicochemical properties of the obtained biocarbons and their interaction with methyl red sodium salt upon adsorption process have been checked. The obtained bioadsorbents were characterized by determination of-low temperature nitrogen adsorption/desorption, elemental analysis, ash content, Boehm titration, and pH of water extracts. The biocarbons have surface area varying from 233-371 m²/g and basic in nature with acidic/basic oxygen-containing functional groups (3.23-5.08 mmol/g). The adsorption capacity varied from 63 to 141 mg/g. The influence of different parameters, such as the effectiveness of methyl red sodium salt adsorption, was evaluated. The adsorption kinetics was well fitted using a pseudo-second-order model. The Freundlich model best represented the equilibrium data. The amount of adsorbed dye was also found to increase with the increasing temperature of the process.

Competitive adsorption of Alizarin Red S and Bromocresol Green from aqueous solutions using brookite TiO2 nanoparticles: experimental and molecular dynamics simulation

In this work, the effective adsorption and the subsequent photodegradation activity, of TiO₂ brookite nanoparticles, for the removal of anionic dyes, namely, Alizarin Red S (ARS) and Bromocresol Green (BCG) were studied. Batch adsorption experiments were conducted to investigate the effect of both dyes' concentration, contact time, and temperature. Photodegradation experiments for the adsorbed dyes were achieved using ultraviolet light illumination (6 W, λ = 365 nm). The single adsorption isotherms were fitted to the Sips model. The binary adsorption isotherms were fitted using the Extended-Sips model. The results of adsorption isotherms showed that the estimated maximum adsorption uptakes in the binary system were around 140 mg g^-1 and 45.5 mg g^-1 for ARS and BCG, respectively. In terms of adsorption kinetics, the uptake toward ARS was faster than BCG molecules in which the equilibrium was obtained in 7 min for ARS, while it took 180 min for BCG. Moreover, the thermodynamics results showed that the adsorption process was spontaneous for both anionic dyes. All these macroscopic competitive adsorption results indicate high selectivity toward ARS molecules in the presence of BCG molecules. Additionally, the TiO₂ nanoparticles were successfully regenerated using UV irradiation. Moreover, molecular dynamics computational modeling was performed to understand the molecules' optimum coordination, TiO₂ geometry, adsorption selectivity, and binary solution adsorption energies. The simulation energies distribution exhibits lower adsorption energies for ARS in the range from - 628 to - 1046 [Formula: see text] for both single and binary systems. In addition to that, the water adsorption energy was found to be between - 42 and - 209 [Formula: see text].