Three-Phase Mixed Titania Powder Modified by Silver and Silver Chloride with Enhanced Photocatalytic Activity under UV-Visible Light

A Fresh Perspective on the Impact of ZnTiO3 Coupling on the Microstructure and Photocatalytic Properties of TiO2 Fabricated at Varied Temperatures

ZnTiO3/TiO2 composite photocatalysts were synthesized via the sol-gel technique, and the impact of varying heat treatment temperatures (470, 570, 670 °C) on their crystalline arrangement, surface morphology, elemental composition, chemical state, specific surface area, optical characteristics, and photocatalytic efficacy was systematically investigated. The outcomes revealed that, as the temperature ascends, pure TiO2 undergoes a transition from anatase to rutile, ultimately forming a hybrid crystal structure at 670 °C. The incorporation of ZnTiO3 engenders a reduction in the TiO2 grain dimensions and retards the anatase-to-rutile phase transition. Consequently, the specimens manifest a composite constitution of anatase and ZnTiO3. In contrast, for pure TiO2, the specimen subjected to 670 °C annealing demonstrates superior photocatalytic performance due to its amalgamated crystal arrangement. The degradation efficacy of methylene blue (MB) aqueous solution attains 91% within a 60-min interval, with a calculated first-order reaction rate constant of 0.039 min-1. Interestingly, the ZnTiO3/TiO2 composite photocatalysts exhibit diminished photocatalytic activity in comparison to pristine TiO2 across all three temperature variations. Elucidation of the photocatalytic mechanism underscores that ZnTiO3 coupling augments the generation of photogenerated charge carriers. Nonetheless, concurrently, it undermines the crystalline integrity of the composite, yielding an excess of amorphous constituents that impede the mobility of photoinduced carriers. This dual effect also fosters escalated recombination of photogenerated charges, culminating in diminished quantum efficiency and reduced photocatalytic performance.

Investigation on the Structural and Photocatalytic Performance of Oxygen-Vacancy-Enriched SnO2-CeO2 Heterostructures

In this study, pure CeO2 and oxygen-vacancy-enriched SnO2-CeO2 composite materials were prepared using the sol-gel method, and their microstructures and photocatalytic properties were investigated. The results indicate that SnO2 coupling promotes the separation and transfer of photogenerated electrons and holes and suppresses their recombination. The 50% SnO2-CeO2 composite material exhibited a decreased specific surface area compared to pure CeO2 but significantly increased oxygen vacancy content, demonstrating the highest photogenerated charge separation efficiency and the best photocatalytic performance. After 120 min of illumination, the degradation degree of MB by the 50% SnO2-CeO2 composite material increased from 28.8% for pure CeO2 to 90.8%, and the first-order reaction rate constant increased from 0.002 min-1 to 0.019 min-1.

Effect of Ag Modification on the Structure and Photocatalytic Performance of TiO2/Muscovite Composites

Ag/TiO2/muscovite (ATM) composites were prepared by the sol–gel method and the effects of Ag modification on the structure and photocatalytic performance were investigated. The photocatalysts were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller surface area (BET), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectra (FTIR), photoluminescence spectra (PL) and ultraviolet–visible diffuse reflectance spectra (DRS). The photocatalytic activity of the obtained composites was evaluated by taking 100 mL (10 mg/L) of Rhodamine B (RhB) aqueous solution as the target pollutant. The muscovite (Mus) loading releases the agglomeration of TiO2 particles and the specific surface area increases from 17.6 m2/g (pure TiO2) to 39.5 m2/g (TiO2/Mus). The first-order reaction rate constant increases from 0.0009 min−1 (pure TiO2) to 0.0074 min−1 (150%TiO2/Mus). Ag element exists in elemental silver. The specific surface area of 1-ATM further increases to 66.5 m2/g. Ag modification promotes the separation of photogenerated electrons and holes and increases the visible light absorption. 1%Ag-TiO2/Mus (1-ATM) exhibits the highest photocatalytic activity. After 100 min, the rhodamine B (RhB) degradation degrees of PT, 150%TiO2/Mus and 1-ATM are 10.4%, 48.6% and 90.6%, respectively. The first-order reaction rate constant of 1-ATM reaches 0.0225 min−1, which is 25 times higher than that of pure TiO2.

Detection of Glucose Based on Noble Metal Nanozymes: Mechanism, Activity Regulation, and Enantioselective Recognition

Glucose monitoring is essential to evaluate the degree of glucose metabolism disorders. The enzymatic determination has been the most widely used method in glucose detection because of its high efficiency, accuracy, and sensitivity. Noble metal nanomaterials (NMs, i.e., Au, Ag, Pt, and Pd), inheriting their excellent electronic, optical, and enzyme-like properties, are classified as noble metal nanozymes (NMNZs). As the NMNZs are often involved in two series of reactions, the oxidation of glucose and the chromogenic reaction of peroxide, here the chemical mechanism by employing NMNZs with glucose oxidase (GOx) and peroxidase (POD) mimicking activities is briefly summarized first. Subsequently, the regulation strategies of the GOx-like, POD-like and tandem enzyme-like activities of NMNZs are presented in detail, including the materials, size, morphology, composition, and the reaction condition of the representative NMs. In addition, in order to further mimic the enantioselectivity of enzyme, the design of NMNZs with enantioselective recognition of d-glucose and l-glucose by using different chiral compounds (DNA, amino acids, and cyclodextrins) and molecular imprinting is further described in this review. Finally, the feasible solutions to the existing challenges and a vision for future development possibilities are discussed.

Controllable Phase Transformation and Enhanced Photocatalytic Performance of Nano-TiO2 by Using Oxalic Acid

Degradation of organic pollutants, especially organic dyes and antibiotics, by semiconductor photocatalysts is an efficient strategy for wastewater treatment. TiO₂ nanomaterials are considered to be promising photocatalysts due to their high chemical stability, high efficiency and availability. Anatase TiO₂ generally has superior photocatalytic activity to the rutile phase. However, the anatase phase can be irreversibly transformed to rutile phase when calcined at an elevated temperature. Methods to improve the stability of anatase are especially important for the TiO₂ gas sensors working at high temperatures. The addition of strong acids can effectively suppress this transformation process. However, these strong acids are relatively expensive, corrosive and environmentally unfriendly. Herein, oxalic acid (OA) as a natural acid was used to control the hydrolysis process of tetrabutyl titanate (TBOT), leading to controllable crystalline phase transformation and reduced crystalline size of TiO₂ on the nanoscale. What is more, the photocatalytic degradation performances were enhanced continuously when the molar ratio of OA to TBOT increased. The degradation reaction rate constants of CT650-R25 were about 10 times that of CT650-R0. The mechanism study shows that the enhanced photocatalytic activity can be attributed to the improved dispersibility, increased specific surface area and reduced recombination rates of photo-induced charge carriers and decreased energy bands as the concentration of OA increased. Thus, this work provides a simple, mild and effective method for controlling the crystalline forms of nano-TiO₂ with enhanced photocatalytic performance towards waste water treatment.