Sol-gel Syntheses of Photocatalysts for the Removal of Pharmaceutical Products in Water

Studies on Synthesis, Characterization, and Photocatalytic Activity of TiO2 and Cr-Doped TiO2 for the Degradation of p-Chlorophenol

TiO₂ and Cr-TiO₂ nanoparticles (NPs) have been synthesized by the sol-gel method using titanium isopropoxide as the precursor of Titania. The prepared samples were analyzed by employing scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infrared analyses. Under UV irradiation, the photocatalytic activities of TiO₂ and Cr-TiO₂ were observed by estimating the % degradation of p-chlorophenol (PCP) as a sample pollutant. The extent of degradation was investigated, varying the catalyst dosage, initial PCP concentration, irradiation time, and solution pH. The experimental results show that efficiency of catalysts initially increases but decreases later on, whereas the % degradation of PCP is the highest at its lowest initial concentration. For TiO₂ and Cr-TiO₂ NPs at their optimal catalyst dosage of 2.0 g/L, acidic pH, and with UV irradiation for 90 min, the observed % degradation of PCP is 50.23 ± 3.12 and 66.51 ± 2.14%, respectively. Thus, the prepared Cr-TiO₂ NPs have enhanced the degradation efficiency of PCP with an irradiation time which is four time less than those reported earlier. From the kinetics analysis, the degradation reaction of PCP is found to follow a pseudo-first-order model and the rate constants are 0.0075 and 0.0122 min^-1 for pure TiO₂ and Cr-TiO₂ NPs, respectively. The present study has further revealed that owing to the lower rate of electron-hole pair recombination, the photocatalytic activity of Cr-TiO₂ NPs becomes higher than that of TiO₂. Therefore, as viable photocatalytic agents, Cr-TiO₂ NPs are suggested to be used also for efficient degradation of other organic pollutants.

Nanocomposites of Titanium Dioxide and Peripherally Substituted Phthalocyanines for the Photocatalytic Degradation of Sulfamethoxazole

Phthalocyanines (Pcs) are often used in photosensitization of titanium(IV) oxide, a commonly employed photocatalyst, as such an approach holds the promise of obtaining highly stable and efficient visible light-harvesting materials. Herein, we report on the preparation, characterization and photoactivity of a series of composites based on TiO₂ and peripherally modified metallophthalocyanines: either tetrasulfonated or 4,4',4'',4'''-tetraazaphthalocyanines, with either copper(II), nickel(II) or zinc(II) as the central metal ion. Physicochemical characterization was performed using UV-Vis diffuse reflectance spectroscopy, hydrodynamic particle-size analysis, surface-area analysis using N₂ adsorption-desorption measurements and thermogravimetry combined with differential scanning calorimetry. The band-gap energy values were lower for the composites with peripherally modified phthalocyanines than for the commercial TiO₂ P25 or the unsubstituted zinc(II) phthalocyanine-grafted TiO₂. TG-DSC results confirmed that the chemical deposition, used for the preparation of Pc/TiO₂ composites, is a simple and efficient method for TiO₂ surface modification, as all the Pc load was successfully grafted on TiO₂. The photocatalytic potential of the Pc/TiO₂ materials was assessed in the photocatalytic removal of sulfamethoxazole-a commonly used antibacterial drug of emerging ecological concern. To compare the activity of the materials in different conditions, photodegradation tests were conducted both in water and in an organic medium.

Degradation of toxic agrochemicals and pharmaceutical pollutants: Effective and alternative approaches toward photocatalysis

Emerging concern regarding the remediation of environmental pollution has expanded tremendously in recent years. Pharmaceutical industries and agricultural sectors release an enormous amount of residues containing toxic pollutants at trace levels which poses a serious impact on the environment and human health. To cope with the effect of hazardous and toxic contaminants, numerous methodologies have been developed for the treatment of effluents released from the agrochemical and pharmaceutical industries. Amongst them, photocatalysis has gained much more attention for the degradation of pollutants due to its low cost, higher capability, green and eco-friendly approaches. Photocatalysts are the substrate that plays a key role in pollutant removal through photocatalysis by accelerating the necessary chemical reactions using a light source. In this review, the recent progress on photocatalysis and its fundamental mechanism in agrochemicals and pharmaceutical pollutant degradation was summarized. This review concisely discusses the incorporation of various metal oxides and nanomaterials into semiconductors for the effective degradation of contaminants. The current status and future research on different sectors and the difficulties in the photocatalytic removal of agrochemical and pharmaceutical pollutants are also reviewed in detail.

Effect of Multiply Twinned Ag(0) Nanoparticles on Photocatalytic Properties of TiO2 Nanosheets and TiO2 Nanostructured Thin Films

Ag-decorated TiO₂ nanostructured materials are promising photocatalysts. We used non-standard cryo-lyophilization and ArF laser ablation methods to produce TiO₂ nanosheets and TiO₂ nanostructured thin films decorated with Ag nanoparticles. Both methods have a common advantage in that they provide a single multiply twinned Ag⁽⁰⁾ characterized by {111} twin boundaries. Advanced microscopy techniques and electron diffraction patterns revealed the formation of multiply twinned Ag⁽⁰⁾ structures at elevated temperatures (500 °C and 800 °C). The photocatalytic activity was demonstrated by the efficient degradation of 4-chlorophenol and Total Organic Carbon removal using Ag-TiO₂ nanosheets, because the multiply twinned Ag⁽⁰⁾ served as an immobilized photocatalytically active center. Ag-TiO₂ nanostructured thin films decorated with multiply twinned Ag⁽⁰⁾ achieved improved photoelectrochemical water splitting due to the additional induction of a plasmonic effect. The photocatalytic properties of TiO₂ nanosheets and TiO₂ nanostructured thin films were correlated with the presence of defect-twinned structures formed from Ag⁽⁰⁾ nanoparticles with a narrow size distribution, tuned to between 10 and 20 nm. This work opens up new possibilities for understanding the defects generated in Ag-TiO₂ nanostructured materials and paves the way for connecting their morphology with their photocatalytic activity.

Advanced oxidation processes for waste water treatment: from laboratory-scale model water to on-site real waste water

A process combining three steps has been developed as a tertiary treatment for waste water in order to remove micropollutants not eliminated by a conventional waste water treatment plant (WWTP). These three processes are ozonation, photocatalysis and granulated activated carbon adsorption. This process has been developed through three scales: laboratory, pilot and pre-industrial scale. At each scale, its efficiency has been assessed on different waste waters: laboratory-made water, industrial waste water (one from a company cleaning textiles and another from a company preparing culture media, both being in continuous production mode) and municipal waste water. At laboratory scale, a TiO₂-based photocatalytic coating has been produced and the combination of ozonation-UVC photocatalytic treatment has been evaluated on the laboratory-made water containing 22 micropollutants. The results showed an efficient activity leading to complete or partial degradation of all compounds and an effective carbon for residual micropollutant adsorption was highlighted. Experiments at pilot scale (100 L of water treated at 500 L/h from a tank of 200 L) corroborated the results obtained at laboratory scale. Moreover, tests on municipal waste water showed a decrease in toxicity, measured on Daphnia Magma, and a decrease in micropollutant concentration after treatment. Finally, a pre-industrial container was built and evaluated as a tertiary treatment at the WWTP Duisburg-Vierlinden. It is shown that the main parameters for the efficiency of the process are the flow rate and the light intensity. The photocatalyst plays a role by degrading the more resistant micropollutants. Adsorption permits an overall elimination >95% of all molecules detected.

Supported TiO2 in Ceramic Materials for the Photocatalytic Degradation of Contaminants of Emerging Concern in Liquid Effluents: A Review

The application of TiO₂ as a slurry catalyst for the degradation of contaminants of emerging concern (CEC) in liquid effluents has some drawbacks due to the difficulties in the catalyst reutilization. Thus, sophisticated and expensive separation methods are required after the reaction step. Alternatively, several types of materials have been used to support powder catalysts, so that fixed or fluidized bed reactors may be used. In this context, the objective of this work is to systematize and analyze the results of research inherent to the application of ceramic materials as support of TiO₂ in the photocatalytic CEC removal from liquid effluents. Firstly, an overview is given about the treatment processes able to degrade CEC. In particular, the photocatalysts supported in ceramic materials are analyzed, namely the immobilization techniques applied to support TiO₂ in these materials. Finally, a critical review of the literature dedicated to photocatalysis with supported TiO₂ is presented, where the performance of the catalyst is considered as well as the main drivers and barriers for implementing this process. A focal point in the future is to investigate the possibility of depurating effluents and promote water reuse in safe conditions, and the supported TiO₂ in ceramic materials may play a role in this scope.

Eco-Friendly Colloidal Aqueous Sol-Gel Process for TiO2 Synthesis: The Peptization Method to Obtain Crystalline and Photoactive Materials at Low Temperature

This work reviews an eco-friendly process for producing TiO2 via colloidal aqueous sol–gel synthesis, resulting in crystalline materials without a calcination step. Three types of colloidal aqueous TiO2 are reviewed: the as-synthesized type obtained directly after synthesis, without any specific treatment; the calcined, obtained after a subsequent calcination step; and the hydrothermal, obtained after a specific autoclave treatment. This eco-friendly process is based on the hydrolysis of a Ti precursor in excess of water, followed by the peptization of the precipitated TiO2. Compared to classical TiO2 synthesis, this method results in crystalline TiO2 nanoparticles without any thermal treatment and uses only small amounts of organic chemicals. Depending on the synthesis parameters, the three crystalline phases of TiO2 (anatase, brookite, and rutile) can be obtained. The morphology of the nanoparticles can also be tailored by the synthesis parameters. The most important parameter is the peptizing agent. Indeed, depending on its acidic or basic character and also on its amount, it can modulate the crystallinity and morphology of TiO2. Colloidal aqueous TiO2 photocatalysts are mainly being used in various photocatalytic reactions for organic pollutant degradation. The as-synthesized materials seem to have equivalent photocatalytic efficiency to the photocatalysts post-treated with thermal treatments and the commercial Evonik Aeroxide P25, which is produced by a high-temperature process. Indeed, as-prepared, the TiO2 photocatalysts present a high specific surface area and crystalline phases. Emerging applications are also referenced, such as elaborating catalysts for fuel cells, nanocomposite drug delivery systems, or the inkjet printing of microstructures. Only a few works have explored these new properties, giving a lot of potential avenues for studying this eco-friendly TiO2 synthesis method for innovative implementations.

Suitability of High-Resolution Mass Spectrometry for Routine Analysis of Small Molecules in Food, Feed and Water for Safety and Authenticity Purposes: A Review

During the last decade, food, feed and environmental analysis using high-resolution mass spectrometry became increasingly popular. Recent accessibility and technological improvements of this system make it a potential tool for routine laboratory work. However, this kind of instrument is still often considered a research tool. The wide range of potential contaminants and residues that must be monitored, including pesticides, veterinary drugs and natural toxins, is steadily increasing. Thanks to full-scan analysis and the theoretically unlimited number of compounds that can be screened in a single analysis, high-resolution mass spectrometry is particularly well-suited for food, feed and water analysis. This review aims, through a series of relevant selected studies and developed methods dedicated to the different classes of contaminants and residues, to demonstrate that high-resolution mass spectrometry can reach detection levels in compliance with current legislation and is a versatile and appropriate tool for routine testing.

Green Synthesis of N/Zr Co-Doped TiO2 for Photocatalytic Degradation of p-Nitrophenol in Wastewater

TiO2 prepared by a green aqueous sol–gel peptization process is co-doped with nitrogen and zirconium to improve and extend its photoactivity to the visible region. Two nitrogen precursors are used: urea and triethylamine; zirconium (IV) tert-butoxide is added as a source of zirconia. The N/Ti molar ratio is fixed regardless of the chosen nitrogen precursor while the quantity of zirconia is set to 0.7, 1.4, 2, or 2.8 mol%. The performance and physico-chemical properties of these materials are compared with the commercial Evonik P25 photocatalyst. For all doped and co-doped samples, TiO2 nanoparticles of 4 to 8 nm of size are formed of anatase-brookite phases, with a specific surface area between 125 and 280 m2 g−1 vs. 50 m2 g−1 for the commercial P25 photocatalyst. X-ray photoelectron (XPS) measurements show that nitrogen is incorporated into the TiO2 materials through Ti-O-N bonds allowing light absorption in the visible region. The XPS spectra of the Zr-(co)doped powders show the presence of TiO2-ZrO2 mixed oxide materials. Under visible light, the best co-doped sample gives a degradation of p-nitrophenol (PNP) equal to 70% instead of 25% with pure TiO2 and 10% with P25 under the same conditions. Similarly, the photocatalytic activity improved under UV/visible reaching 95% with the best sample compared to 50% with pure TiO2. This study suggests that N/Zr co-doped TiO2 nanoparticles can be produced in a safe and energy-efficient way while being markedly more active than state-of-the-art photocatalytic materials under visible light.

Photodecomposition of pharmaceuticals and personal care products using P25 modified with Ag nanoparticles in the presence of natural organic matter

The presence of pharmaceuticals and personal care products (PPCPs) in water remains a concern due to their potential threat to environmental and human health. Advanced oxidation processes (AOPs) have been receiving attention in water treatment studies to remove PPCPs. However, most studies have been focused on pure water containing a limited number of substances. In this study, the photocatalytic efficiency of commercially available titanium dioxide nanoparticles (P25) and P25 modified by silver nanoparticles (Ag-P25) were compared for their ability to degrade 23 target PPCPs (2 μg L^-1) in realistic water matrices containing natural organic matter (Suwanee River NOM, 6.12 mg L^-1). The experiments were completed under ultraviolet-light emitting diode (UV-LED) illumination at 365 and 405 nm wavelengths, with the latter representing visible light exposure. Under 365 nm UV-LED treatment, 99% of the PPCPs were removed using both P25 and Ag-P25 photocatalysts within 180 min of the treatment duration. The number of PPCPs removed dropped to 57% and 53% for P25 and Ag-P25 respectively under the 405 nm UV-LED irradiation. Dissolved organic carbon (DOC) and UV absorbance at 254 nm (UV254) measured at the end of the experiment indicated that the aromatic fraction of NOM was preferentially removed from the water matrix. Also, Ag-P25 was more effective in DOC removal than P25. The relationships of removal rate constants with physico-chemical properties of the substances were also determined. The molecular weight and charge were strongly associated with removal, with the former and the latter being positively and negatively correlated with the rate constants. The results of this work indicate that Ag-P25 is a promising photocatalyst to degrade persistent substances such as PPCPs and NOM even if they are present in a complex water matrix. The properties of individual substances can also be employed as an indication of their removal using this technology.

Activation Treatments and SiO2/Pd Modification of Sol–Gel TiO2 Photocatalysts for Enhanced Photoactivity under UV Radiation

The objective of this work is to improve the efficiency of TiO2 photocatalysts by activation treatments and by modification with palladium nanoparticles and doping with SiO2. The influence of the additive loading was explored, and two activation treatments were performed: UV exposition and H2 reduction. TiO2/SiO2/Pd photocatalysts were synthesized by an original cogelation method: a modified silicon alkoxide, i.e., [3-(2-aminoethyl)aminopropyl]trimethoxysilane (EDAS), was used to complex the palladium ions, thanks to the ethylenediamine group, while the alkoxide groups reacted with TiO2 precursors. Pure TiO2 was also synthesized by the sol–gel process for comparison. X-ray diffraction evidenced that the crystallographic structure of TiO2 was anatase and that Pd was present, either in its oxidized form after calcination, or in its reduced form after reduction. The specific surface area of the samples varied from 5 to 145 m2 g-1. Transmission electron microscopy allowed us to observe the homogeneous dispersion and nanometric size of Pd particles in the reduced samples. The width of the band gap for pure TiO2 sample, measured by UV/Visible diffuse reflectance spectroscopy at approximately 3.2 eV, corresponded to that of anatase. The band gap for the TiO2/SiO2/Pd composite samples could not be calculated, due to their high absorption in visible range. The photocatalytic activity of the various catalysts was evaluated by the degradation of a methylene blue solution under UV radiation. The results showed that the photocatalytic activity of the catalysts was inversely proportional to the content of silica present in the matrix. A small amount of silica improved the photocatalytic activity, as compared to the pure TiO2 sample. By contrast, a high amount of silica delayed the crystallization of TiO2 in its anatase form. The activation treatment under UV had little influence on photocatalytic efficiency. The introduction of Pd species increased the photocatalytic activity of the samples because it allowed for a decrease in the rate of electron–hole recombinations in TiO2. The reduction treatment improved the activity of photocatalysts, whatever the palladium content, thanks to the reduction of Ti4+ into Ti3+, and the formation of defects in the crystallographic structure of anatase.

Impact of Titanium Dioxide (TiO2) Modification on Its Application to Pollution Treatment—A Review

A high-efficiency method to deal with pollutants must be found because environmental problems are becoming more serious. Photocatalytic oxidation technology as the environmentally-friendly treatment method can completely oxidate organic pollutants into pollution-free small-molecule inorganic substances without causing secondary pollution. As a widely used photocatalyst, titanium dioxide (TiO2) can greatly improve the degradation efficiency of pollutants, but several problems are noted in its practical application. TiO2 modified by different materials has received extensive attention in the field of photocatalysis because of its excellent physical and chemical properties compared with pure TiO2. In this review, we discuss the use of different materials for TiO2 modification, highlighting recent developments in the synthesis and application of TiO2 composites using different materials. Materials discussed in the article can be divided into nonmetallic and metallic. Mechanisms of how to improve catalytic performance of TiO2 after modification are discussed, and the future development of modified TiO2 is prospected.

Advanced photocatalytic oxidation processes for micropollutant elimination from municipal and industrial water

The objective of this study was to develop and validate an innovative technology to ensure efficient elimination of different types of micropollutants and toxic compounds in waste water. The process is a tertiary treatment process, which can be easily integrated into municipal and industrial waste water treatment plants. It is based on oxidation by ozone and subsequent photocatalytic treatment. After development and validation of this system at laboratory scale, the solution was tested at pilot scale. The first part of this work was to develop a TiO₂-based film on glass substrate, characterize its physico-chemical properties and optimize its composition at laboratory scale to be photoactive on the degradation of model water containing several pollutants. The model water consisted of a mixture of 22 major micropollutants including pesticides, plasticizers, brominated compounds, and pharmaceuticals. The best photocatalyst for the degradation of the selected micropollutants was a TiO₂ coating doped with 2 wt% of Ag and where 10 wt% P25 was added. Then, in order to scale up the process, its deposition on steel substrates was tested with dip and spray coating at laboratory scale. Calcination parameters were optimized to limit steel corrosion while keeping similar photoactive properties regarding the degradation of the model polluted water. The optimized solution was deposited by spray coating in a pilot scale reactor in order to assess its efficiency in a pilot water treatment plant.

Visible Light Sensitive SnO2/ZnCo2O4 Material for the Photocatalytic Removal of Organic Pollutants in Water

In this study, pure ZnCo2O4 and SnO2/ZnCo2O4 mix photocatalysts have been synthesized by the sol-gel process with three different SnO2 loading percentages (10, 20, and 30 wt %). Their photocatalytic activities were assessed on the degradation of organic pollutants in water under visible illumination. The structural, morphological, and optical properties were analyzed by X-ray diffraction (XRD), scanning electron microscopy, energy-dispersive X-ray (EDX), Fourier transform infrared (FTIR), nitrogen adsorption-desorption isotherms, X-ray photoelectron spectroscopy (XPS), and UV–Visible diffuse reflectance measurements. The results have shown that the materials are composed of a crystalline ZnCo2O4 matrix with a decrease in crystallite size with the amount of SnO2. Weakly crystalline SnO2 is also observed for loaded samples. The specific surface area is modified with the loading ratio. The evaluation of the photoactivity of the samples under visible light for the degradation of p-nitrophenol has highlighted that all materials are highly photoactive under visible light thanks to heterojunction between the two oxides. An application test has been conducted on a dye, congo red, showing the same tendencies. An optimal amount of SnO2 loading is observed for the sample containing 20 wt % of SnO2. A comparison with commercial Evonik P25 showed that the materials developed in this work have five to six times better efficiency under visible light, leading to a promising photocatalyst material.

Evaluation of Solar-Driven Photocatalytic Activity of Thermal Treated TiO₂ under Various Atmospheres

In this report, the photocatalytic activity of P25 has been explored and the influence of thermal treatment under various atmospheres (air, vacuum and hydrogen) were discussed. The samples’ characteristics were disclosed by means of various instruments including X-ray diffraction (XRD), Electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS) and UV–vis. This study also accentuates various states of the oxygen vacancy density formed inside the samples as well as the colour turning observed in treated P25 under various atmospheres. Produced coloured TiO₂ samples were then exploited for their photocatalytic capability concerning photodegradation of methylene blue (MB) using air mass (AM) 1.5 G solar light irradiation. Our findings revealed that exceptional photocatalytic activity of P25 is related to the thermal treatment. Neither oxygen vacancy formation nor photocatalytic activity enhancement was observed in the air-treated sample. H₂-treated samples have shown better photoactivity which even could be further improved by optimizing treatment conditions to achieve the advantages of the positive role of oxygen vacancy (O-vacancy at higher concentration than optimum acts as electron trapping sites). The chemical structure and stability of the samples were also studied. There was no sign of deteriorating of O₂-vacancies inside the samples after 6 months. High stability of thermal treated samples in terms of both long and short-term time intervals is another significant feature of the produced photocatalyst.