Mechanical Properties Changes of Irradiated Thermoplastic Elastomer

Effects of Electron Irradiation and Temperature on Mechanical Properties of Polyimide Film

Polyimide (PI) is widely deployed in space missions due to its good radiation resistance and durability. The influences from radiation and harsh temperatures should be carefully evaluated during the long-term service life. In the current work, the coupled thermal and radiation effects on the mechanical properties of PI samples were quantitatively investigated via experiments. At first, various PI specimens were prepared, and electron irradiation tests were conducted with different fluences. Then, both uniaxial tensile tests at room temperature and the dynamic mechanical analysis at varied temperatures of PI specimens with and without electron irradiation were performed. After that, uniaxial tensile tests at low and high temperatures were performed. The fracture surface of the PI film was observed using a scanning electron microscope, and its surface topography was measured using atomic force microscopy. In the meantime, the Fourier-transform infrared spectrum tests were conducted to check for chemical changes. In conclusion, the tensile tests showed that electron irradiation has a negligible effect during the linear stretching period but significantly impacts the hardening stage and elongation at break. Moreover, electron irradiation slightly influences the thermal properties of PI according to the differential scanning calorimetry results. However, both high and low temperatures dramatically affect the elastic modulus and elongation at break of PI.

Evaluation of Cross-Linked Polyamide 6 Micro-Indentation Properties: TAIC Concentration and Electron Radiation Intensity

Nowadays, technical practice puts emphasis on improving selected material properties of polymers which could lead to new applications. Material properties can be modified in numerous ways, among which is radiation treatment. This study looks into the influence of beta radiation on several properties of polyamide 6, e.g., indentation hardness, modulus and creep. Main changeable parameters were the concentration of triallyl isocyanurate (TAIC), which promotes cross-linking, and intensity of radiation. The concentration was in the range from 2 to 6 wt.%, while the radiation dose was 0, 66, 99 and 132 kGy. The treated materials were measured for indentation hardness, modulus and creep. Degree of cross-linking was verified by thermo-mechanical analysis (TMA), while degradation processes was investigated by Fourier-transform infrared spectroscopy (FTIR). The results indicate that electron radiation positively affects the tested material properties. The best results were seen in polyamide with 6 wt.% of TAIC, which demonstrated a 38% improvement in mechanical properties after exposure to 132 kGy. This improvement in properties affects the final parts and their application (e.g., in the automotive industry-engine parts; in electrical engineering-insulation of wires and cables; and in industry-pipes for underfloor heating, etc.).

Influence of Cross-Linking Agent Concentration/Beta Radiation Surface Modification on the Micro-Mechanical Properties of Polyamide 6

This study focuses on the problematic of polyamide 6 containing various concentrations of cross-linking agent that was exposed to electron radiation. It is important to improve the material properties of polymers as much as possible. This endeavor can be realized by numerous methods, one of which is radiation exposure. This study investigates the effect of electron beam radiation in doses ranging from 66 to 132 kGy on the micro-mechanical properties of polymers, specifically polyamide 6 filled with 1, 3 and 5 wt.% of cross-linking agent triallyl isocyanurate (TAIC). The changes in the material brought by the radiation exposure were quantified by measurements of indentation hardness and modulus, which were the main measured micro-mechanical properties. Furthermore, thermo-mechanical analysis (TMA) was chosen to confirm the results of the material cross-linking, while the effect of degradation was investigated by Fourier-transform infrared spectroscopy (FTIR). In pursuit of complete evaluation, the topography of the test subject's surface was explored by atomic force microscopy (AFM). The optimal concentration/radiation ratio was found in polyamide 6 enriched by 5 wt.% concentration of TAIC, which was irradiated by 132 kGy. Material treated in such a way had its indentation hardness by 33% and indentation modulus improved by 26% in comparison with the untreated material. These results were subsequently confirmed by the TMA and FTIR methods.

The Influence of Surface Quality on Flow Length and Micro-Mechanical Properties of Polycarbonate

This study describes the influence of polymer flow length on mechanical properties of tested polymer, specifically polycarbonate. The flow length was examined in a spiral shaped mould. The mould cavity’s surface was machined by several methods, which led to differing roughness of the surface. The cavity was finished by milling, grinding and polishing. In order to thoroughly understand the influence of the mould surface quality on the flow length, varying processing parameters, specifically the pressure, were used. The polymer part was divided into several segments, in which the micro-mechanical properties, such as hardness and indentation modulus were measured. The results of this study provide interesting data concerning the flow length, which was up to 3% longer for rougher surfaces, but shorter in cavities with polished surface. These results are in disagreement with the commonly practiced theory, which states that better surface quality leads to greater flow length. Furthermore, evaluation of the micro-mechanical properties measured along the flow path demonstrated significant variance in researched properties, which increased by 35% (indentation hardness) and 86% by indentation modulus) in latter segments of the spiral in comparison with the gate.

AgNPs@ZnO hybride nanoparticles infused thermoplastic polyester elastomer and their biocide effect

This paper presents research results of biocidal effect of thermoplastic- polyester-elastomer (TPE-E) with incorporation of hybrid Ag/ZnO/SiO2 NPs (silver/Zinc oxide/SiO2 nanoparticles). These results were compared with various gamma-irradiated doses and processing techniques including extrusion, injection molding and compression molding. In all these processing techniques the TPE-E was mixed with mineral oil and Ag/ZnO/SiO2 nanoparticles. The TPE-E nanocomposites were characterized by differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), Infrared FT spectroscopy (FTIR), surface enhanced Raman technique (SERS), FESEM (Field emission scanning electron microscopy), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), TEM (transmission electronic microscopy) and antimicrobial test. Antibacterial activity against E. coli and S. aureus, are reported and these results showed potential application in health care products.

Polyamide Surface Layer Nano-Indentation and Thermal Properties Modified by Irradiation

This study describes the effect of electron radiation on the nano-mechanical properties of surface layers of selected polyamide (PA) types. Electron radiation initiates the cross-linking of macromolecules in the polyamide structure, leading to the creation of a 3D network which fundamentally changes the properties of the tested polymers. Selected types of polyamide (PA 6, PA 66 and PA 9T) were exposed to various intensities of electron radiation (33 kGy, 66 kGy, 99 kGy, 132 kGy, 165 kGy and 198 kGy). The cross-linked polyamides’ surface properties were measured by means of the modern nano-indentation technique (Depth Sensing Indentation; DSI), which operates on the principle of the immediate detection of indenter penetration depth in dependence on the applied load. The evaluation was preformed using the Oliver–Pharr method. The effect of electron radiation on the tested polyamides manifested itself in the creation of a 3D network, which led to an increase of surface layer properties, such as indentation hardness, elastic modulus, creep and temperature resistance, by up to 93%. The increase of temperature and mechanical properties substantially broadens the field of application of these materials in technical practice, especially when higher temperature resistance is required. The positive changes to the nano-mechanical properties as well as mechanical and temperature capabilities instigated by the cross-linking process were confirmed by the gel volume test. These measurements lay the foundation for a detailed study of this topic, as well as for a more effective means of modifying chosen properties of technical polyamide products by radiation.

Nano-Mechanical Properties of Surface Layers of Polyethylene Modified by Irradiation

This study’s goal was to describe the influence of a wide range of ionizing beta radiation upon the changes in surface layer mechanical properties and structural modifications of selected types of polymer. Radiation crosslinking is a process whereby the impingement of high-energy electrons adjusts test sample structures, thus enhancing the useful properties of the material, e.g., hardness, wear-resistance, and creep, in order that they may function properly during their technical use. The selected polymers tested were polyolefin polymers like polyethylene (Low-density polyethylene LDPE, High-density polyethylene HDPE). These samples underwent exposure to electron radiation of differing dosages (33, 66, 99, 132, 165, and 198 kGy). After the crosslinking process, the samples underwent testing of the nano-mechanical properties of their surface layers. This was done by means of a state-of-the-art indentation technique, i.e., depth-sensing indentation (DSI), which detects the immediate change in the indentation depth associated with the applied force. Indeed, the results indicated that the optimal radiation dosage increased the mechanical properties by up to 57%; however, the beneficial levels of radiation varied with each material. Furthermore, these modifications faced examination from the structural perspective. For this purpose, a gel test, Raman spectroscopy, and crystalline portion determination by X-ray all confirmed the assumed trends.

The Effect of High-Energy Ionizing Radiation on the Mechanical Properties of a Melamine Resin, Phenol-Formaldehyde Resin, and Nitrile Rubber Blend

Irradiation by ionizing radiation is a specific type of controllable modification of the physical and chemical properties of a wide range of polymers, which is, in comparison to traditional chemical methods, rapid, non-polluting, simple, and relatively cheap. In the presented paper, the influence of high-energy ionizing radiation on the basic mechanical properties of the melamine resin, phenol-formaldehyde resin, and nitrile rubber blend has been studied for the first time. The mechanical properties of irradiated samples were compared to those of non-irradiated materials. It was found that radiation doses up to 150 kGy improved the mechanical properties of the tested materials in terms of a significant increase in stress at break, tensile strength, and tensile modulus at 40% strain, while decreasing the value of strain at break. At radiation doses above 150 kGy, the irradiated polymer blend is already degrading, and its tensile characteristics significantly deteriorate. An radiation dose of 150 kGy thus appears to be optimal from the viewpoint of achieving significant improvement, and the radiation treatment of the given polymeric blend by a beam of accelerated electrons is a very promising alternative to the traditional chemical mode of treatment which impacts the environment.

The Electrical, Mechanical and Surface Properties of Thermoplastic Polyester Elastomer Modified by Electron Beta Radiation

The main advantages of Thermoplastic Polyester Elastomers (TPE-E) are their elastomer properties as well as their ability to be processed in the same way as thermoplastic polymers (e.g., injection moulding, compression moulding and extrusion). However, TPE-Es' properties, mainly their mechanical properties and thermal characteristics, are not as good as those of elastomers. Because of this TPE-Es are often modified with the aim of improving their properties and extending their range of application. Radiation cross-linking using accelerated electron beams is one of the most effective ways to change virgin polymers' properties significantly. Their electrical (that is to say permittivity and resistivity measurements), mechanical (that is, tensile and impact tensile tests), as well as surface (that is, nano-indentation) properties were measured on modified/cross-linked TPE-E specimens with and/or without a cross-linking agent at irradiation doses of 0, 33, 66, 99, 132, 165 and 198 kGy. The data acquired from these procedures show significant changes in the measured properties. The results of this study allow the possibility of determining the proper processing parameters and irradiation doses for the production of TPE-E products which leads to the enlargement of their application in practice.

Mechanical Measurement System and Precision Analysis for Tactile Property Evaluation of Porous Polymeric Materials

Tactile properties are one of the most important attributes of porous polymeric materials such as textiles, comprising a subjective evaluation index for textile materials and functional clothing, primarily affecting the sensation of comfort during the wearing of a garment. A new test method was proposed, and a mechanical measurement system was developed to objectively characterize the tactile properties of porous polymeric materials by simulating the dynamic contact processes during human skin contact with the materials and in consideration of different aspects of tactile sensations. The measurement system can measure the bending, compression, friction, and thermal transfer properties in one apparatus, and is capable of associating the objective measurements with the subjective tactile sensations. The test and evaluation method, the components of the mechanical measurement system, the definition and grading method of the evaluation indices, and the neural network prediction model from objective test results to subjective sensations of tactile properties were presented. The experiments were conducted for the objective tests and correlation tests. Seven types of porous polymeric sheet materials from seven categories for the tactile properties were cut to a size of 200 mm × 200 mm and tested. Each index of tactile properties was significantly different (P < 0.05) between different sheet materials. The correlations of bending, compression, friction, and thermal transfer properties with Kawabata KES test methods were analyzed. An intra-laboratory test was conducted and an analysis of the variance was performed to determine the critical differences of within laboratory precisions of the measurement system. This mechanical measurement system provides a method and system for objective measurement and evaluation of tactile properties of porous polymeric sheet materials in industrial application.