Green Flexible Polyurethane Foam as a Potent Support for Fe-Si Adsorbent

The adsorbent preparation of FeOOH@PU for effective chromium (VI) removal

A novel adsorbent (FeOOH@PU) for hexavalent chromium [Cr(VI)] removal was synthesized using a polyurethane foam (PU) and FeOOH via a facile one-step method. Scanning electron microscopy (SEM), FTIR, X-ray photoelectron spectroscopy (XPS), and energy dispersive spectroscopy (EDS) characterized the adsorbent. The influence of environmental factors was investigated to evaluate the adsorption behavior for Cr(VI). Furthermore, adsorption dynamic and adsorption isotherm models described the adsorption performance. This adsorbent also treated electroplating wastewater and remediated simulated Cr(VI) contaminated soil. The adsorbent effectively removed Cr(VI) with a high adsorption rate; its equilibrium rate constant was 13 times that of FeOOH. Cr(VI) removal was a monolayer adsorption process and the maximum adsorption capacity of FeOOH@PU reached 34.9 mg Cr/g. Electrostatic attraction was the mechanism of Cr(VI) removal. Electroplating wastewater became clear and the Cr(VI) concentration decreased from 9.76 to 0.042 mg/L after treatment with FeOOH@PU. Cr enrichment in rice seedlings grown in remediated soil decreased from 7.687 to 6.295 mg Cr/kg. These results suggested that FeOOH@PU was a promising adsorbent for Cr(VI) removal and Cr(VI) stabilization.

Removal of Cationic Dyes by Iron Modified Silica/Polyurethane Composite: Kinetic, Isotherm and Thermodynamic Analyses, and Regeneration via Advanced Oxidation Process

Emerging dye pollution from textile industrial effluents is becoming more challenging for researchers worldwide. The contamination of water by dye effluents affects the living organisms in an ecosystem. Methylene blue (MB) and malachite green (MG) are soluble dyes with a high colour intensity even at low concentration and are hazardous to living organisms. The adsorption method is used in most wastewater plants for the removal of organic pollutants as it is cost-effective, has a high adsorption capacity, and good mechanical stabilities. In this study, a composite adsorbent was prepared by impregnating iron modified silica (FMS) onto polyurethane (PU) foam to produce an iron modified silica/polyurethane (FMS/PU) composite. The composite adsorbent was utilised in batch adsorption of the cationic dyes MB and MG. The effect of adsorption parameters such as the adsorbent load, pH, initial dye concentration, and contact time were discussed. Adsorption kinetics and isotherm were implemented to understand the adsorption mechanism for both dyes. It was found that the adsorption of MB and MG followed the pseudo-second order model. The Langmuir model showed a better fit than the Freundlich model for the adsorption of MB and MG, indicating that the adsorption occurred via the monolayer adsorption system. The maximum adsorption capacity of the FMS/PU obtained for MB was 31.7 mg/g, while for MG, it was 34.3 mg/g. The thermodynamic study revealed that the adsorption of MB and MG were exothermic and spontaneous at room temperature. In addition, the regeneration of FMS/PU was conducted to investigate the composite efficiency in adsorbing dyes for several cycles. The results showed that the FMS/PU composite could be regenerated up to four times when the regeneration efficiency dropped drastically to less than 20.0%. The impregnation of FMS onto PU foam also minimised the adsorbent loss into the environment.

Effects of different substrates on the adsorption behavior of supported-adsorbents: A case study of MoS2 for Ag+ adsorption

Supported-adsorbents growing on the substrate in situ are equipped with the advantages of high adsorption capacity, excellent regeneration performance, and adaptability to complex wastewater. However, the effects of substrate on the adsorption properties of supported-adsorbent are rarely considered, which will hinder its development and scale-up applications. In this study, the influences of different substrates (Ti, Mo, W, CC) on the Ag⁺ adsorption behavior of supported-MoS₂ adsorbents were investigated. The adsorption kinetics, adsorption mechanism, and the renewability of these supported-MoS₂ were compared orderly. As a result, MoS₂ grown on a tungsten substrate (MoS₂-W) exhibits a remarkable adsorption capacity for Ag⁺ (1.98 mg cm^-2 and 598.80 mg g^-1), which is 6.38-33 times more than the other three supported-MoS₂. Moreover, the MoS₂-W also possesses an ultrahigh distribution coefficient (24.80 mL cm^-2) for Ag⁺, and the selection coefficient can reach 1984. XRD and electrochemical characterization analysis indicated that Ag⁺ adsorption performance of supported-MoS₂ is positively correlated with the degree of its amorphous structure. Substrate W with the terrific electrical properties which may facilitate the disordered growth of MoS₂, resulting in more active sites exposed, and endow MoS₂-W with outstanding Ag⁺ capture performance. Finally, the supported-MoS₂ retains a high removal efficiency of Ag⁺ after 5 cycles of adsorption and desorption. This study provides a novel perspective for promoting the practical application of supported-sorbents to recycle heavy metals.

Novel Sustainable Castor Oil-Based Polyurethane Biocomposites Reinforced with Piassava Fiber Powder Waste for High-Performance Coating Floor

The search for new greener materials that contribute to a more sustainable world motivated the present study in which novel biocomposites with 10, 20 and 30 vol% of piassava fiber powder waste reinforcing castor oil-based polyurethane (COPU) intended for a high-performance coated floor (HPCF) were developed. The novel biocomposites were characterized by flexural, Izod impact and wear standard tests as well as Fourier transform infrared spectroscopy (FTIR) and fracture analysis using scanning electron microscopy (SEM). Both flexural modulus and strength displayed marked increases reaching more than 800 and 500%, respectively, compared to plain COPU for 30 vol% piassava powder incorporation. FTIR bands indicated the existence of interaction between the piassava constituents and COPU. However, SEM fractographs disclosed the presence of bubbles attributed to retained gases during the COPU curing. Consequently, the Izod impact resistance showed a 50% decrease while the wear was more than three times accentuated for 30 vol% piassava powder biocomposite. These results met the specified values of corresponding standards and revealed a promising new greener material for HPCFs.

Fabrication of Mesoporous Silica Nanoparticle-Incorporated Coaxial Nanofiber for Evaluating the In Vitro Osteogenic Potential

The most important role of tissue engineering is to develop a biomaterial with a property that mimics the extracellular matrix (ECM) by enhancing the lineage-specific proliferation and differentiation with favorable regeneration property to aid in new tissue formation. Thus, to develop an ideal scaffold for bone repair, we have fabricated a composite nanofiber by the coaxial electrospinning technique. The coaxial electrospun nanofiber contains the core layer, consisting of polyvinyl alcohol (PVA) blended with oregano extract and mesoporous silica nanoparticles (PVA-OE-MSNPs), and the shell layer, consisting of poly-ε-caprolactone blended with collagen and hydroxyapatite (PCL-collagen-HAP). We evaluated the physicochemical properties of the nanofibers using X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). In vitro biocompatibility, cell adhesion, cell viability, and osteogenic potential were evaluated by 3-(4,5-dimethylthiazole-2-yl)-2,5-diphenlytetrazolium bromide (MTT), calcein AM, and alkaline phosphatase (ALP) activity and Alizarin Red staining in NIH 3T3/MG-63 cells. The results showed that the nanoparticle-incorporated coaxial nanofiber was observed with bead-free, continuous, and uniform fiber morphology with a mean diameter in the range of 310 ± 125 nm. From the biochemical studies, it is observed that the incorporation of nanofiber with HAP and MSNPs shows good swelling property with ideal porosity, biodegradation, and enhanced biomineralization property. In vitro results showed that the scaffolds with nanoparticles have higher cell adhesion, cell viability, ALP activity, and mineralization potential. Thus, the fabricated nanofiber could be an appropriate implantable biomaterial for bone tissue engineering.

Flexible Polyurethane Foams from Epoxidized Vegetable Oils and a Bio-Based Diisocyanate

Bio-polyols from epoxidized soybean and linseed oils and caprylic acid or 3-phenyl butyric acid were prepared using an environmentally friendly, solvent-free method evaluating the presence of triethylamine as catalyst. Side reactions, leading to a cross-linking structure with high density, were reduced, introducing the catalyst and properly tuning the reaction conditions. A medium functionality value of around 3 along with a hydroxyl number up to around 90 mg KOH/g, narrow polydispersity index, and relatively low molecular mass up to 2400 g/mol were the experimental targets. From selected bio-polyols and an aliphatic partially bio-based isocyanate, a series of water blown polyurethane (PU) foams was produced, estimating the effect of the chemical nature of substituents in the polyol backbone on the PU properties. The apparent density of the foams was in the range of 79–113 kg/m³, with higher values for foams from the aromatic acid. Flexible polyurethane foams with open cell structure from bio-based polyols were obtained, with higher cavity size and lower pore sizes for foams from caprylic acid. The bio-based flexible PU foams showed comparable Young’s moduli (14–18 kPa) and compression deflection values (4.6–5.5 kPa) and exhibited an almost complete recovery of their initial size.

Adsorption Evaluation for the Removal of Nickel, Mercury, and Barium Ions from Single-Component and Mixtures of Aqueous Solutions by Using an Optimized Biobased Chitosan Derivative

In this experimental study, the use of 5-hydroxymethyl-furfural (HMF) organic compound as a grafting agent to chitosan natural polymer (CS) was examined. One optimized chitosan derivative was synthesized, and then tested (CS-HMF), in order to uptake nickel, mercury, and barium metal ions from single- and triple-component (multi-component) aqueous solutions. The characterization of the material before and after the metal uptake was achieved by scanning electron microscopy (SEM). The ability of the adsorption of CS-HMF was tested at pH = 6. The adjusting of temperature from 25 to 65 °C caused the increase in the adsorption capacity. The equilibrium data were fitted to the models of Langmuir and Freundlich, while the data from kinetic experiments were fitted to pseudo-1st and pseudo-2nd order models. The best fitting was achieved for the Langmuir model (higher R²). The adsorption capacity for nickel, mercury, and barium removal at 25 °C (single component) was 147, 107, and 64 (mg/g), respectively. However, the total adsorption capacity for the multi-component was 204 mg/g. A thermodynamic study was also done, and the values of ΔG⁰, ΔH⁰, and ΔS⁰ were evaluated.

Polystyrene Magnetic Nanocomposites as Antibiotic Adsorbents

There are different ways for antibiotics to enter the aquatic environment, with wastewater treatment plants (WWTP) considered to be one of the main points of entrance. Even treated wastewater effluent can contain antibiotics, since WWTP cannot eliminate the presence of antibiotics. Therefore, adsorption can be a sustainable option, compared to other tertiary treatments. In this direction, a versatile synthesis of poly(styrene-block-acrylic acid) diblock copolymer/Fe3O4 magnetic nanocomposite (abbreviated as P(St-b-AAc)/Fe3O4)) was achieved for environmental applications, and particularly for the removal of antibiotic compounds. For this reason, the synthesis of the P(St-b-AAc) diblock copolymer was conducted with a reversible addition fragmentation transfer (RAFT) method. Monodisperse superparamagnetic nanocomposite with carboxylic acid groups of acrylic acid was adsorbed on the surface of Fe3O4 nanoparticles. The nanocomposites were characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD) and vibrating sample magnetometer (VSM) analysis. Then, the nanoparticles were applied to remove ciprofloxacin (antibiotic drug compound) from aqueous solutions. The effects of various parameters, such as initial drug concentration, solution pH, adsorbent dosage, and contact time on the process were extensively studied. Operational parameters and their efficacy in the removal of Ciprofloxacin were studied. Kinetic and adsorption isothermal studies were also carried out. The maximum removal efficiency of ciprofloxacin (97.5%) was found at an initial concentration of 5 mg/L, pH 7, adsorbent's dosage 2 mg/L, contact time equal to 37.5 min. The initial concentration of antibiotic and the dose of the adsorbent presented the highest impact on efficiency. The adsorption of ciprofloxacin was better fitted to Langmuir isotherm (R2 = 0.9995), while the kinetics were better fitted to second-order kinetic equation (R2 = 0.9973).

Chitosan Grafted with Biobased 5-Hydroxymethyl-Furfural as Adsorbent for Copper and Cadmium Ions Removal

This work investigates the application of 5-hydroxymethyl-furfural (HMF) as a grafting agent to chitosan (CS). The material produced was further modified by cross-linking. Three different derivatives were tested with molecular ratios CS/HMF of 1:1 (CS-HMF1), 2:1 (CS-HMF2) and 10:1 mol/mol (CS-HMF3)) to remove Cu²⁺ and Cd²⁺ from aqueous solutions. CS-HMF derivatives were characterized both before, and after, metal ions adsorption by using scanning electron microscopy (SEM), as well as Fourier-transform infrared (FTIR) spectroscopy thermogravimetric analysis (TGA), and X-Ray diffraction analysis (XRD). The CS-HMF derivatives were tested at pH = 5 and showed higher adsorption capacity with the increase of temperature. Also, the equilibrium data were fitted to Langmuir (best fitting) and Freundlich model, while the kinetic data to pseudo-first (best fitting) and pseudo-second order equations. The Langmuir model fitted better (higher R²) the equilibrium data than the Freundlich equation. By increasing the HMF grafting from 130% (CS-HMF1) to 310% (CS-HMF3), an increase of 24% (26 m/g) was observed for Cu²⁺ adsorption and 19% (20 mg/g) for Cd²⁺. By increasing from T = 25 to 65 °C, an increase of the adsorption capacity (metal uptake) was observed. Ten reuse cycles were successfully carried out without significant loss of adsorption ability. The reuse potential was higher of Cd²⁺, but more stable desorption reuse ability during all cycles for Cu²⁺.