Microstructural Evolution of Poly(ε-Caprolactone), Its Immiscible Blend, and In Situ Generated Nanocomposites

Current advances and emerging trends in sustainable polyhydroxyalkanoate modification from organic waste streams for material applications

The current processes for producing polyhydroxyalkanoates (PHAs) are costly, owing to the high cost of cultivation feedstocks, and the need to sterilise the growth medium, which is energy-intensive. PHA has been identified as a promising biomaterial with a wide range of potential applications and its functionalization from waste streams has made significant advances recently, which can help foster the growth of a circular economy and waste reduction. Recent developments and novel approaches in the functionalization of PHAs derived from various waste streams offer opportunities for addressing these issues. This study focuses on the development of sustainable, efficient, and cutting-edge methods, such as advanced bioprocess engineering, novel catalysts, and advances in materials science. Chemical techniques, such as epoxidation, oxidation, and esterification, have been employed for PHA functionalization, while enzymatic and microbial methods have indicated promise. PHB/polylactic acid blends with cellulose fibers showed improved tensile strength by 24.45-32.08 % and decreased water vapor and oxygen transmission rates while PHB/Polycaprolactone blends with a 1:1 ratio demonstrated an elongation at break four to six times higher than pure PHB, without altering tensile strength or elastic modulus. Moreover, PHB films blended with both polyethylene glycol and esterified sodium alginate showed improvements in crystallinity and decreased hydrophobicity.

Approaches to Control Crazing Deformation of PHA-Based Biopolymeric Blends

The mechanical behavior of polymer materials is heavily influenced by a phenomenon known as crazing. Crazing is a precursor to damage and leads to the formation of cracks as it grows in both thickness and tip size. The current research employs an in situ SEM method to investigate the initiation and progression of crazing in all-biopolymeric blends based on Polyhydroxyalkanoates (PHAs). To this end, two chemically different grades of PHA, namely poly(hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBHV), were melt-blended with polybutyrate adipate terephthalate (PBAT). The obtained morphologies of blends, the droplet/fibrillar matrix, were highly influenced by the plasticity of the matrices as well as the content of the minor phase. Increasing the concentration of PBAT from 15 to 30 wt.% resulted in the brittle to ductile transition. It changed the mechanism of plastic deformation from single craze-cracking to homogeneous and heterogeneous intensified crazing for PHB and PHBHV matrices, respectively. Homogeneous tensile crazes formed perpendicularly to the draw direction at the initial stages of deformation, transformed into shear crazes characterized by oblique edge propagation for the PHBHV/PBAT blend. Such angled crazes suggested that the displacement might be caused by shear localized deformation. The crazes' strength and the time to failure increased with the minor phase fibers. These fibers, aligned with the tensile direction and spanning the width of the crazes, were in the order of a few micrometers in diameter depending on the concentration. The network of fibrillar PBAT provided additional integrity for larger plastic deformation values. This study elucidates the mechanism of crazing in PHA blends and provides strategies for controlling it.

Rheological Considerations in Processing Self-Reinforced Thermoplastic Polymer Nanocomposites: A Review

The present review relates to the field of nanocomposite materials comprising a thermoplastic nanofibrillar phase dispersed in a matrix that is also thermoplastic. The fact of forming the nanofibrillar phase in situ during melt processing gives it the role of a reinforcing nanofiller for thermoplastic materials. This paper discusses the major factors influencing the formation of self-reinforced nanofibrillar polymer composite (NFC) materials throughout manufacturing steps. More specifically, the rheological considerations allowing the prediction of the in situ nanofibrillation during melt blending and post-processing as well as the methods of production of these polymer nanocomposites are described. The major challenges related to the future development in the field of NFCs are addressed. The concept of self-reinforced nanofibrillar polymer materials shows great potential in lightweight eco-design processes and represents a new approach to polymer nanocomposite recycling for a variety of industrial applications.

Viscoelastic, Thermal, and Mechanical Properties of Melt-Processed Poly (ε-Caprolactone) (PCL)/Hydroxyapatite (HAP) Composites

Poly (ε-caprolactone) (PCL)/hydroxyapatite (HAP) composites represent a novel material with desired properties for various applications. In this work, PCL/HAP composites at low loadings were developed through melt-extrusion processing. The effects of HAP loading on viscoelastic, thermal, structural, and mechanical properties of PCL were examined. The morphological analysis revealed better dispersion of HAP at low loadings, while aggregation was noticed at high concentrations. The complex viscosity of the prepared composites increased with increasing concentration of HAP. In addition, a significant decrease in crystallinity was observed upon increase in HAP loading. However, the elongation at break increased with increasing the concentration of HAP, probably due to a decrease in crystallinity. The onset thermal degradation temperature of PCL was enhanced at low concentrations of HAP, whereas a decrease was observed at high loading. Overall, different degrees of HAP dispersion resulted into specific property improvement.

Polycarbonate/Poly(vinylidene fluoride)-Blend-Based Nanocomposites-Effect of Adding Different Carbon Nanofillers/Organoclay

Carbon black (CB), carbon nanotubes (CNTs), and graphene nanoplatelets (GnPs) individually or doubly served as reinforcing fillers in polycarbonate (PC)/poly(vinylidene fluoride) (PVDF)-blend (designated CF)-based nanocomposites. Additionally, organo-montmorillonite (15A) was incorporated simultaneously with the individual carbon fillers to form hybrid filler nanocomposites. Microscopic images confirmed the selective localization of carbon fillers, mainly in the continuous PC phase, while 15A located in the PVDF domains. Differential scanning calorimetry results showed that blending PVDF with PC or forming single/double carbon filler composites resulted in lower PVDF crystallization temperature during cooling. However, PVDF crystallization was promoted by the inclusion of 15A, and the growth of β-form crystals was induced. The rigidity of the CF blend increased after the formation of nanocomposites. Among the three individually added carbon fillers, GnPs improved the CF moduli the most; the simultaneous loading of CNT/GnP resulted in the highest moduli by up to 33%/46% increases in tensile/flexural moduli, respectively, compared with those of the CF blend. Rheological viscosity results showed that adding CNTs increased the complex viscosity of the blend to a greater extent than did adding CB or GnPs, and the viscosity further increased after adding 15A. The electrical resistivity of the blend decreased with the inclusion of carbon fillers, particularly with CNT loading.

Shear-Induced and Nanofiber-Nucleated Crystallization of Novel Aliphatic-Aromatic Copolyesters Delineated for In Situ Generation of Biodegradable Nanocomposites

The shear-induced and cellulose-nanofiber nucleated crystallization of two novel aliphatic-aromatic copolyesters is outlined due to its significance for the in situ generation of biodegradable nanocomposites, which require the crystallization of nanofibrous sheared inclusions at higher temperatures. The shear-induced non-isothermal crystallization of two copolyesters, namely, poly(butylene adipate-co-succinate-co-glutarate-co-terephthalate) (PBASGT) and poly(butylene adipate-co-terephthalate) (PBAT), was studied following a light depolarization technique. To have a deep insight into the process, the effects of the shear rate, shear time, shearing temperature and cooling rate on the initiation, kinetics, growth and termination of crystals were investigated. Films of 60 μm were subjected to various shear rates (100-800 s-1) for different time intervals during cooling. The effects of the shearing time and increasing the shear rate were found to be an elevated crystallization temperature, increased nucleation density, reduced growth size of lamella stacks and decreased crystallization time. Due to the boosted nucleation sites, the nuclei impinged with each other quickly and growth was hindered. The effect of the cooling rate was more significant at lower shear rates. Shearing the samples at lower temperatures, but still above the nominal melting point, further shifted the non-isothermal crystallization to higher temperatures. As a result of cellulose nanofibers' presence, the crystallization of PBAT, analyzed by DSC, was shifted to higher temperatures.

In Situ Generation of Green Hybrid Nanofibrillar Polymer-Polymer Composites-A Novel Approach to the Triple Shape Memory Polymer Formation

The paper discusses the possibility of using in situ generated hybrid polymer-polymer nanocomposites as polymeric materials with triple shape memory, which, unlike conventional polymer blends with triple shape memory, are characterized by fully separated phase transition temperatures and strongest bonding between the polymer blends phase interfaces which are critical to the shape fixing and recovery. This was demonstrated using the three-component system polylactide/polybutylene adipateterephthalate/cellulose nanofibers (PLA/PBAT/CNFs). The role of in situ generated PBAT nanofibers and CNFs in the formation of efficient physical crosslinks at PLA-PBAT, PLA-CNF and PBAT-CNF interfaces and the effect of CNFs on the PBAT fibrillation and crystallization processes were elucidated. The in situ generated composites showed drastically higher values of strain recovery ratios, strain fixity ratios, faster recovery rate and better mechanical properties compared to the blend.