Study on Improving the Processability and Properties of Mixed Polyolefin Post-Consumer Plastics for Piping Applications

Advancing the Characterization of Recycled Polyolefin Blends with a Combined Experimental and Numerical Approach to Thermomechanical Behavior

The blending of polyolefins (POs), such as polyethylene (PE) and polypropylene (PP), is a growing area of research, particularly for recycling mixed polyolefin (MPO) waste through flotation sorting techniques. However, understanding the thermomechanical behavior of these recycled blends is challenging due to limitations in the existing characterization methods. This paper introduces a combined experimental and numerical method to accurately assess the complex mechanical behavior of high-density PE, PP, and their blends. We conducted detailed thermomechanical analyses using a high-speed stereo digital image correlation (DIC) system paired with an infrared camera to capture temperature variations alongside mechanical stress and strain. This approach allowed us to correct for distortions caused by necking and to derive accurate stress-strain relationships. We also applied a cutting-edge unified semi-crystalline polymer (USCP) model to simplify the analysis, focusing on the effects of strain rate and temperature, including self-heating and thermal softening phenomena. Our results, which closely match experimental observations of stress-strain behavior and temperature changes, offer new insights into the thermomechanical properties of PO blends, which are essential for advancing their practical applications in various fields.

Assessment of Melt Compounding with Zeolites as an Effective Deodorization Strategy for Mixed Plastic Wastes and Comparison with Degassing

The emission of off-odors from mechanically recycled plastics severely limits their re-introduction into the market for the production of new objects, for the same use or even for less demanding applications, thus hindering the implementation of an effective circular economy for plastics. The addition of adsorbing agents during the extrusion of polymers represents one of the most promising strategy to reduce the odorous emissions of plastics, due to its characteristics of cost-effectiveness, flexibility and low energy consumption. The novelty of this work lies in the assessment of zeolites as VOC adsorbents during the extrusion of recycled plastics. They appear more suitable than other types of adsorbents, due to their ability to capture and "hold" the adsorbed substances at the high temperatures of the extrusion process. Moreover, the effectiveness of this deodorization strategy was compared with the traditional degassing technique. Two types of mixed polyolefin wastes, coming from completely different collection and recycling processes, were tested: Fil-S (Film-Small), deriving from post-consumer flexible films of small size, and PW (pulper waste), which is the residual plastic waste obtained from the paper recycling process. The melt compounding of the recycled materials with two micrometric zeolites (zeolite 13X and Z310) resulted as more effective in the off-odors removal with respect to degassing. In particular, the highest reduction (-45%) of the Average Odor Intensity (AOI) was measured for both PW/Z310 and Fil-S/13X systems at 4 wt% of the zeolites' amount, compared with the corresponding untreated recyclates. Finally, by combining degassing and melt compounding with zeolites, the best result was obtained for the composite Fil-S/13X, whose Average Odor Intensity resulted as quite close (+22%) to the one of the virgin LDPE.

Assessment of the Impact of Superficial Contamination and Thermo-Oxidative Degradation on the Properties of Post-Consumer Recycled Polypropylene

Single-use plastics are a matter of convenience in everyday life, with the majority allocated to packaging production. However, it comes with a high environmental price as its mass recycling is challenging due to the heterogeneity of composition, contaminations of different kinds, and degradation caused by service and processing. This study aims to ascertain the impact of removing contaminants from post-consumer recycled polypropylene (rPP) on its degradation and properties by implementing a systematic approach for decontamination by washing. Four lots of recycled plastics with different degrees of contamination were evaluated via Fourier transform infrared, melt flow indexer, and differential scanning calorimetry and tested for tensile strength. Degradation of the rPP was manifested by the deterioration in ductility, resulting in 14.58% elongation at break (unwashed rPP) compared with 191.41% (virgin PP)) and a significant reduction in oxidation induction time. In the unwashed rPP sample, a wave intensity peak at 1730 cm^-1, assigned to the saturated C = 0 stretch of the carbonyl functional group, was detected. This peak was gradually disappearing with an increase in the cleaning efficiency of rPP, highlighting the role of contaminants as degradation catalysts. The cold-washing method showed similar processing and mechanical performance improvement results compared with the other washing methods, while being more environmentally friendly and energy efficient.

Manufacture and Characterization of Polypropylene (PP) and High-Density Polyethylene (HDPE) Blocks for Potential Use as Masonry Component in Civil Construction

The lack of suitable destinations for plastics materials can be a global environmental problem. The alternative use of materials for sustainable construction encourages the standardization of waste and promotes effective social, environmental and economic gains at the local level and ensures savings and income for communities. The aim of this paper is the development, manufacture, and characterization of PP and HDPE recycled polyolefin blocks as masonry components in civil construction. These blocks were manufactured by the rotational molding process. Besides this, the mechanical, physical, impact and flammability properties of the blocks were studied. In conclusion, HDPE showed better behavior than PP in tests realized.

Effect of the Intercalation and Dispersion of Organoclays on Energy Demand in the Extrusion of Recycled HDPE/PP Nanocomposites

Few studies have drawn on any systematic research into the energy demand to produce polymer-based nanocomposites. Regarding the problem, it is well-known that single screw extrusion is an energy-intensive process, so the incorporation of energy meters must be considered to examine the energy efficiency of the process. In this study, the effect of a nanoclay addition on the energy demand of the extrusion process was examined by extruding recycled high-density polyethylene (rHDPE) and recycled polypropylene (rPP) with a gradual compression screw with both dispersive and distributive mixers. The rHDPE/rPP was modified by adding commercial organoclay (OMMT) (3 wt%) and olefin block copolymer (OBC) (5 wt%) as compatibilizers. The energy consumption was measured on the total energy of the extruder machine. Mass throughput (MT) and specific energy consumption (SEC) were obtained at different screw speeds (10, 20, 30, 40, 50 RPM). The SEC of OMMT and OMMT/OBC nanocomposites was 25–50% lower than rHDPE/rPP, especially at higher throughputs. X-ray diffraction (XRD) and scanning electron microscope (SEM) illustrated the degree of intercalation and dispersion of the organoclay at different screw speeds. Better organoclay intercalation and dispersion were found at lower temperatures. Rheological curves showed a decrease in the viscosity at extrusion rates of nanocomposite mixtures. Melt temperature measured at die exit was reduced in the presence of organoclay over the screw speeds studied. This work suggests that the processing of rHDPE/rPP based nanocomposites can result in minor costs when processing conditions are carefully selected.

Using Computational Modelling to Study Extensional Rheometry Tests for Inelastic Fluids

The present work focuses on the extensional rheometry test, performed with the Sentmanat extensional rheometer (SER) device, and its main objectives are: (i) to establish the modelling requirements, such as the geometry of the computational domain, initial and boundary conditions, appropriate case setup, and (ii) to investigate the effect of self-induced errors, namely on the sample dimensions and test temperature, on the extensional viscosity obtained through the extensional rheometry tests. The definition of the modelling setup also comprised the selection of the appropriate mesh refinement level to model the process and the conclusion that gravity can be neglected without affecting the numerical predictions. The subsequent study allowed us to conclude that the errors on the sample dimensions have similar effects, originating differences on the extensional viscosity proportional to the induced variations. On the other hand, errors of a similar order of magnitude on the test temperature promote a significant difference in the predicted extensional viscosity.

Nanosilicates in Compatibilized Mixed Recycled Polyolefins: Rheological Behavior and Film Production in a Circular Approach

Currently, plastic packaging represents a global challenge and has become a key point of attention for governments, media and consumers due to the visibility of the waste it generates. Despite their high resource efficiency, the perceived non-recyclability of polymeric films risks precluding them from being a relevant packaging solution in a circular economy approach. In this regard, the aim of this study was to implement a strategy to try closing the loop, via the mechanical recycling of post-consumer flexible packaging of small size (denoted as Fil-s) to obtain new films. In particular, two lots of Fil-s were used, which are PE/PP blends differing for the PP content and the presence of polar contaminants. The suitability for film blowing extrusion of these recycled materials, as such and after the addition of a compatibilizer and/or a lamellar nanosilicate, was evaluated. It was first evidenced that the difficulty of producing blown films with the pristine recycled materials, due to the frequent bubble breakages, occurring even at low draw ratios. Moreover, the shear and extensional rheological behavior of all Fil-s based systems was usefully correlated with their processability features, evidencing the key roles of the nanofiller to stabilize the bubble and of the compatibilizer to ensure a uniform film deformation, avoiding its premature breakage. Even if the adopted upgrading strategies allowed the production of blown films with both types of Fil-s, the different components of the recycled matrices were proven to significantly affect their processability and final film performances.

Characterization of Composition and Structure-Property Relationships of Commercial Post-Consumer Polyethylene and Polypropylene Recyclates

The current efforts in moving closer towards a circular plastics economy puts massive pressure on recycled plastics, especially recycled polyethylene (rPE) and recycled polypropylene (rPP) to enter new markets. Their market penetration remained low so far, despite PE and PP constituting the largest share of plastic wastes. However, with the current imperative of more circularity comes a new focus on performance of recyclates. Hence, a detailed understanding of composition and structure–property relationships of post-consumer recyclates has to be developed. Five recycling companies from the Austrian and German markets were asked to supply their purest high-quality rPE and rPP grades. These were characterized by differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), and Fourier-transform infrared (FTIR) spectroscopy, and micro-imaging. Technological characterization included density measurements, determination of the melt flow rate (MFR), and Charpy impact testing. All recyclates contained diverse contaminants and inclusions ranging from legacy fillers like calcium carbonate to polymeric contaminants like polyamides or polyolefin cross-contamination. The overall amount, size, and distribution of contaminants varied significantly among suppliers. Furthermore, first structure–property relationships for polyolefin recyclates that link inorganic content and polymeric purity with density and impact performance could be derived.

Martin P, R. Hanna P, P. Kearns M, Mendes LC, Millar B. Use of virgin/recycled polyethylene blends in rotational moulding

Aiming to further plastics recycling via rotational moulding plastics processing, blends of virgin and recycled polyethylene sourced from post-consumer plastics were developed. Three different kinds of recycled high density polyethylene – from bottles, pipes and mixed household waste – were compounded with virgin medium density polyethylene in an extruder. The ideal amount of recyclate was chosen based upon the impact resistance of different contents (25, 50 and 75%) of recycled plastic with the 50/50 blend found to have the best performance. Compression-moulded and rotationally-moulded samples were analysed through falling dart impact test, flexural test, melt flow rate and differential scanning calorimetry analysis. The impact results of the compression-moulded samples showed an increase in the impact resistance of the blends with a higher melt flow index and lower degree of crystallinity. The rotationally-moulded specimens displayed much lower impact resistance than the pure virgin plastic and a 20–30% reduction in the flexural moduli, which were ascribed to the crystalline structure of the part and issues in the blends’ rotomoulding process. It was concluded that blending virgin and recycled polyethylene for rotational moulding can be an effective way to further plastics recycling inside the Circular Economy context.