Adsorption Behavior of Methylene Blue Dye by Novel CrossLinked O-CM-Chitosan Hydrogel in Aqueous Solution: Kinetics, Isotherm and Thermodynamics

Hydrogels comprising oxidized carboxymethyl cellulose and water-soluble chitosan at varied oxidation levels: Synthesis, characterization, and adsorptive toward methylene blue

Chitosan, as a biomaterial, has increasingly garnered attention. However, its limited solubility in water-only dissolving in certain dilute acidic solutions-substantially restricts its broader application. In this investigation, chitosan underwent a solubilization modification to acquire water solubility, facilitating its dissolution in neutral aqueous mediums. Subsequently, this water-soluble chitosan (WSC) was interlinked with oxidized carboxymethyl cellulose (OCMC), characterized by varied oxidation extents, to synthesize hydrogels. Structural characterization verified the formation of imine bonds resulting from crosslinking interactions between the amino groups of water-soluble chitosan and the aldehyde groups of oxidized carboxymethyl cellulose. Employing performance characterization analysis, it was discerned that an increase in the oxidation level of the oxidized carboxymethyl cellulose corresponded to a denser hydrogel network architecture and the hardness increased from 3.01 N to 6.16 N. Moreover, the capacity of these hydrogels to adsorb methylene blue was meticulously examined. Notably, the hydrogel denoted as WSC/66%OCMC manifested an adsorption capability of 28.08 mg/g for methylene blue. Analytical findings from adsorption kinetics and isotherm studies indicate that the adsorption mechanism of the WSC/66%OCMC hydrogel follows the pseudo-second-order kinetic model and corresponds to the Freundlich isotherm model.

Synthesis, characterization and evaluation of in vitro potential antimicrobial efficiency of new chitosan hydrogels and their CuO nanocomposites

The phenomenon of microbial resistance and its resulting biofilms to traditional antibiotics is worsening over time. Therefore, the discovery of alternative substances that inhibit microbial activities through mechanisms different from those of known antibiotics requires attention. So, chitosan was crosslinked using different amounts of oxalyl dihydrazide yielding four novel hydrogels; ODHCs-I, ODHCs-II, ODHCs-III, and ODHCs-IV of crosslinking degree 12.17, 20.67, 31.67, and 43.17, respectively. Different amounts of CuO nanoparticles were impregnated into ODHCs-IV, obtaining ODHCs-IV/CuONPs-1 %, ODHCs-IV/CuONPs-3 % and ODHCs-IV/CuONPs-5 % composites. Their structure was emphasized using FTIR, SEM, XRD, TEM, EDX and elemental analysis. Their in vitro antimicrobial and anti-biofilm activities improved with increasing ODH and CuONPs content. ODHCs-IV exhibited minimal inhibition concentration (2 μg/mL) against S. pyogenes that was much lower than Vancomycin (3.9 μg/mL). ODHCs-IV/CuONPs-5 % displayed better inhibition performance than Vancomycin and Amphotericin B against Gram-positive-bacteria and fungi, respectively, and comparable one to that of Vancomycin against Gram-negative-bacteria. ODHCs-IV/CuONPs-5 % displayed much lower minimal biofilm inhibition concentrations (1.95 to 3.9 μg/mL) as compared with those of ODHCs-IV (7.81 and 15.63 μg/mL), against C. albicans, S. pyogenes, and K. pneumonia. ODHCs-IV/CuONPs-5 % composite is safe on normal human cells. Oxalyl dihydrazide and CuONPs amalgamated into chitosan in one formulation promoted its antimicrobial efficiency.

One-step hydrothermal synthesis of CeVO4/bentonite nanocomposite as a dual-functional photocatalytic adsorbent for the removal of methylene blue from aqueous solutions

Cerium vanadate/modified bentonite (CeVO4/mbt) nanocomposite with different composition percentages was synthesized through a simple one-step hydrothermal method at 180 ℃, and then its photocatalytic activity was evaluated by decolorizing methylene blue (MB) in an aqueous solution under light exposure. In order to increase the surface area as an important parameter in photocatalytic processes, bentonite was modified by ball mill method. The structural and optical properties of the synthesized composites were determined by XRD, FT-IR, DRS, FESEM, EDS, and BET measurements. XRD and EDS results confirmed the successful synthesis of pure CeVO4. FESEM images and EDS mapping showed a proper distribution of rice-like CeVO4 nanoparticles on bentonite. The removal efficiency of MB with only 0.1 g of CeVO4/mbt nanocomposite in 15 min was about 99%, which is significant compared to neat bentonite and pure CeVO4 with efficiency of 30% and 57%. The mentioned nanocomposite followed the first-order kinetics, had a reaction rate constant equal to 0.1483 min-1, and showed acceptable stability in five consecutive cycles.

Evaluation of the in vitro anti-inflammatory and anti-Helicobacter pylori activities of chitosan-based biomaterials modified with copper oxide nanoparticles

For chemical modification, p-aminobenzoic acid was incorporated into chitosan Schiff base (ACsSB) and chitosan (ACs). Two ACs-based CuO nanoparticles composites; ACs/CuONPs-1 % and ACs/CuONPs-5 %, were also synthesized. Their structures were emphasized utilizing several analytical techniques; elemental analysis, FTIR, 1H NMR, XRD, SEM, EDX and TEM. Compared with standard cyclooxygenase (COX) inhibitor, Celecoxib, the prepared biomaterials showed in vitro selective inhibitory effectiveness against COX-2 enzyme that could be sorted, according to their MIC values that produce 50 % inhibition of COX-2 enzyme activity, as follows: Celecoxib (0.28 μg/mL) > ACs/CuONPs-5 % (4.1 μg/mL) > ACs/CuONPs-1 % (14.8 μg/mL) > ACs (38.5 μg/mL) > ACsSB (58.9 μg/mL) > chitosan (>125 μg/mL). Further, ACs/CuONPs-5 % has more in vitro inhibition efficiency towards Helicobacter pylori (H. pylori) than the other prepared biomaterials. Interestingly, the MIC value of 100 % growth inhibition of H. pylori for ACs/CuONP-5 % is equal to that of drug Clarithromycin (1.95 μg/mL). Thus, ACs/CuONPs-5 % has a promising potential as anti-H. pylori and selective anti-inflammatory agent. ACs/CuONPs-5 % is safe on the human gastric normal cells (GES-1). Therefore, amalgamation of both p-aminobenzoic acid and CuONPs into chitosan extremely promoted its anti-inflammatory and anti-H. pylori activity. This is a promising approach to achieve methods successful to compete the conventional antibiotics.

Microfluidic Fabrication of Monodisperse and Recyclable TiO2-Poly(ethylene glycol) Diacrylate Hybrid Microgels for Removal of Methylene Blue from Aqueous Medium

Nearly monodisperse titanium oxide-polyethylene glycol diacrylate [TiO2-P(EGDA)] hybrid microbeads containing 0.5 wt % TiO2 nanoparticles entrapped within a P(EGDA) cross-linked polymeric network were synthesized using a modular Lego-inspired glass capillary microfluidic device. TiO2-P(EGDA) hybrid microgels were characterized by optical microscopy, scanning electron microscopy, X-ray diffraction, energy dispersive X-ray spectroscopy, and thermogravimetric analysis. The fabricated TiO2-P(EGDA) hybrid microgel system showed 100% removal efficiency of methylene blue (MB) from its 1-3 ppm aqueous solutions after 4 h of UV light irradiation at 0.2 mW/cm2 at the loading of 25 g/L photocatalyst beads in the reaction mixture, corresponding to the loading of naked TiO2 of just 0.025 g/L. No decrease in photocatalytic efficiency was observed in 10 repeated runs with recycled photocatalyst using a fresh 1 ppm MB solution in each cycle. The rate of photocatalytic degradation was controlled by the UV light irradiance, catalyst loading, and the initial dye concentration. Physical adsorption of MB onto the surface of composite microgel was also observed. The adsorption data was best fitted with the Langmuir adsorption isotherm and the Elovich kinetic model. TiO2-P(EGDA) microgel beads are biocompatible, can be prepared with a tunable size in the microfluidic device, and can easily be separated from the reaction mixture by gravity settling. The TiO2-P(EGDA) system can be used for the removal of other toxic dyes and micropollutants from industrial wastewater.

Poly (Vinyl Alcohol) Hydrogels Boosted with Cross-Linked Chitosan and Silver Nanoparticles for Efficient Adsorption of Congo Red and Crystal Violet Dyes

In our previous work, three different weight ratios of chitosan/PVA (1:3, 1:1, and 3:1) were blended and then cross-linked with trimellitic anhydride isothiocyanate (TAI) at a concentration depending on their chitosan content, obtaining three hydrogels symbolized by H13, H11, and H31. Pure chitosan was cross-linked with TAI, producing a hydrogel symbolized by H10. Further, three H31-based silver nanoparticles composites (H31/AgNPs1%, H31/AgNPs3%, and H31/AgNPs5%) were also synthesized. They were investigated, for the first time in this study, as adsorbents for Congo Red (CR) and Crystal Violet (CV) dyes. The removal efficiency of CR dye increased with increasing H10 content in the hydrogels, and with increasing AgNP content in the composites, reaching 99.91% for H31/AgNPs5%. For CV dye, the removal efficiency increased with the increase in the PVA content. Furthermore, the removal efficiency of CV dye increased with an increasing AgNP content, reaching 94.7% for H31/AgNPs5%. The adsorption capacity increased with the increase in both the initial dye concentration and temperature, while with an increasing pH it increased in the case of CV dye and decreased in the case of CR dye. The adsorption of CV dye demonstrated that the Freundlich isotherm model is better suited for the experimental results. Moreover, the results were best fitted with pseudo-second-order kinetic model.

Facile fabrication of Artemisia sphaerocephala krasch gum hydrogels by radiation induced cross-linking polymerization and enhanced ultrahigh adsorption for methylene blue

Although Artemisia sphaerocephala krasch gum (ASKG) has attracted growing attention in the field of medical engineering and food industries, however, there are few studies on the gelation of ASKG. In this paper, acrylic acid modified ASKG hydrogels were prepared by radiation induced grafting, cross-linking and polymerization technique for the first time. The semi-IPN structure was prepared by the cross-linked ASKG network and poly-AAc dispersed within the network. The effects of the adsorbed dose on the swelling ratio and gel fraction were investigated. The different acrylic acid content modified ASKG hydrogels (ASKGAAc1 and ASKGAAc2) for methyl blue (MB) adsorption were investigated, and the ASKG hydrogels was also studied for comparison. The influence of pH, contact time, initial concentration, temperature, ion strength on MB adsorption were tested. The results showed that acrylic acid can promote the formation of hydrogel and greatly enhanced the adsorption of ASKG. The adsorption isotherms were well obeyed the Langmuir model, and the maximum adsorption capacity for MB of ASKG, ASKGAAc1 and ASKGAAc2 were 571.43, 1517.8 and 1654.9 mg/g, respectively. Moreover, the MB adsorption by ASKG based hydrogels was exothermic, spontaneous, and more favorable at lower temperature. Furthermore, the adsorption-desorption experiments demonstrated a good reusability of these hydrogels.

Optimization, Kinetics, and Isotherm Studies of Methyl Thioninium Chloride Removal from Simulated Solutions Using Chitosan Derivatives

Methylene blue (MB) dye or methyl thioninium chloride is one of the hazardous cationic dyes that are discharged into the textile effluent causing a highly negative environmental impact. The present work targets the investigation of the adsorption performance of some chitosan-modified products toward the MB dye from simulated solutions. The claimed chitosan derivatives were prepared, characterized, and applied for the removal of lead and copper cations from an aqueous medium in a previous work. These include: N,O-carboxymethyl chitosan (N,O-CM/Cs), chitosan grafted with glutaraldehyde (Cs/GA), chitosan cross-linked with GA/epichlorohydrin (Cs/GA/ECH), and chitosan cross-linked with glutaraldehyde/methylene bis(acrylamide) (Cs/GA/MBA). The modified chitosan derivatives in this study displayed outstanding mechanical qualities, exceptional reusability, and a significant amount of adsorption capacity. The ability of prepared Cs derivatives to eradicate MB was as follows: N,O-CM/Cs (95.1 mg/g) < Cs/GA (120.1 mg/g) < Cs/GA/ECH (220.1 mg/g) < Cs/GA/MBA (270.0 mg/g). The swelling performance of the prepared sorbents was verified under different experimental conditions, and the data revealed that the maximum swelling was attained at pH = 9, temperature 55 °C, and after 24 h. The produced Cs derivatives showed exceptional reusability by maintaining higher adsorption effectiveness throughout five cycles. The MB dye was adsorbed onto the modified derivatives according to pseudo-second-order kinetics and the Langmuir model. Moreover, the adsorption process was monitored via atomic force microscopy to verify the differences between the dye-free and dye-loaded adsorbents.

Reinforcement of the antimicrobial activity and biofilm inhibition of novel chitosan-based hydrogels utilizing zinc oxide nanoparticles

Two novel chemically cross-linked chitosan hydrogels were successfully prepared via insertion of oxalyl dihydrazide moieties between chitosan Schiff's base chains (OCsSB) and between chitosan chains (OCs). For more modification, two different concentrations of ZnO nanoparticles (ZnONPs) were loaded into OCs to obtain OCs/ZnONPs-1 % and OCs/ZnONPs-3 % composites. The prepared samples were recognized using elemental analyses, FTIR, XRD, SEM, EDS and TEM. Their inhibitory action against microbes and biofilms were classified as: OCs/ZnONPs-3 % > OCs/ZnONPs-1 % > OCs > OCsSB > chitosan. OCs has inhibition activity similar to Vancomycin of minimum inhibitory concentration (MIC) value of 3.9 μg/mL against P. aeruginosa. OCs exhibited minimum biofilm inhibitory concentration (MBIC) values (from 31.25 to 62.5 μg/mL) less than that of OCsSB (from 62.5 to 250 μg/mL) which lower than that of chitosan (from 500 to 1000 μg/mL) against S. epidermidis, P. aeruginosa and C. albicans. OCs/ZnNPs-3 % showed MIC value (that caused 100 % inhibition of Clostridioides difficile, C. difficile) of 0.48 μg/mL much lower than Vancomycin (1.95 μg/mL). Both OCs and OCs/ZnONPs-3 % composite were safe on normal human cells. Thus, inclusion of oxalyl dihydrazide and ZnONPs into chitosan greatly reinforced its antimicrobial activity. This is a good strategy to accomplish adequate systems for competing traditional antibiotics.

Use of Insect-Derived Chitosan for the Removal of Methylene Blue Dye from Wastewater: Process Optimization Using a Central Composite Design

Insects are a readily available source of chitosan due to their high reproductive rates, ease of breeding, and resistance to changes in their ecosystem. This study aimed to extract chitosan from several widespread insects: Blaps lethifera (CS-BL), Pimelia fernandezlopezi (CS-PF), and Musca domestica (CS-MD). The study was also extended to using the obtained chitosans in removing methylene blue dye (MB) from wastewater. The source of the chitosan, the initial concentration of MB dye, and the reaction time were chosen as the working parameters. The experiments were designed using a central composite design (CCD) based on the dye removal efficiency as the response variable. The experimental work and statistical calculation of the CCD showed that the dye removal efficiency ranged from 35.9% to 88.7% for CS-BL, from 18.8% to 47.1% for CS-PF, and from 10.3% to 29.0% for CS-MD at an initial MB concentration of 12.79 mg/L. The highest methylene blue dye removal efficiency was 88.7% for CS-BL at a reaction time of 120 min. This indicates that the extraction of chitosan from insects (Blaps lethifera) and its application in dye removal is a promising, environmentally friendly, economical, biodegradable, and cost-effective process. Furthermore, the CCD is a statistical experimental design technique that can be used to optimize process variables for removing other organic pollutants using chitosan.

Ionic Liquid Cross-Linked High-Absorbent Polymer Hydrogels: Kinetics of Swelling and Dye Adsorption

The use of polymer gels for the removal of toxic chemicals from wastewater is an important area in terms of both academic and industrial research. This work presents a simple approach to the fabrication of chemically cross-linked cationic hydrogel adsorbents using designed ionic liquid-based cross-linkers and their successful use in the removal of organic dyes. Two different ionic liquid cross-linkers, [VIm-4VBC][Cl] (ILA)/[DMAEMA-4VBC][Cl] (ILB), are synthesized by the simple nucleophilic substitution reaction of 4-vinylbenzyl chloride (4VBC) separately with 1-vinylimidazole (VIm) and 2-(dimethylamino)ethyl methacrylate (DMAEMA). Cross-linked poly(acrylamide) (CPAam) and poly(2-hydroxyethyl methacrylate) (CPHEMA) hydrogels are then prepared from the corresponding monomers and as-synthesized cross-linkers (ILA and ILB) by free radical polymerization in the presence of a redox initiator combining ammonium persulfate (APS) and N,N,N',N'-tetramethylethylenediamine (TEMED). The dried CPAam and CPHEMA xerogels exhibit macroporous morphology and high thermal stability. The hydrogel samples exhibit high swelling behavior, and the diffusion of water molecules into the hydrogels follows pseudo-Fickian kinetics. The cationic cross-linking sites in the hydrogel networks allow preferable binding with anionic dyes, and these dye uptake capacities are determined using different model anionic dyes via UV-vis spectroscopy. The dye adsorption onto these hydrogels follows a pseudo-second-order kinetic model. The adsorption mechanism is also analyzed by employing intraparticle diffusion and Boyd kinetic models. The relationship between the maximum equilibrium adsorption capacity (q_m) of the hydrogels for eosin B (EB) dye and the equilibrium EB concentration can be better described by Langmuir and Freundlich isotherm models, and the estimated q_m using the Langmuir isotherm can reach more than 100 mg g^-1. The cross-linked hydrogels can be easily regenerated and have a recycling efficiency of >80% for up to three consecutive dye adsorption-desorption cycles, which is promising for their use in wastewater treatment.

Preparation of hydrogels based on poplar cellulose and their removal efficiency of Cd(II) from aqueous solutions

Industrial heavy metal-contaminated wastewater is one of the main water pollution problems. Adsorbents are a promising method for the removal of heavy metal contaminants. Herein, polyaspartic acid/carboxymethyl poplar sawdust hydrogels (PASP/CMPP) and ascorbic acid/carboxymethyl poplar sawdust hydrogels (VC/CMPP) were prepared by aqueous polymerization using alkalized poplar sawdust (CMPP) as the substrate and PASP and vitamin C (VC) as modifiers. The effective results, provided by the characterization analysis of SEM and BET, indicate that the surface of the PASP/CMPP hydrogel has a larger number of loose pores and a larger pore volume than the VC/CMPP hydrogel. The treatment effects of the two hydrogels on simulated wastewater containing Cd(II) were investigated by a batch of experiments. The results showed that PASP/CMPP had a better adsorption effect than VC/CMPP under the same adsorption conditions. Interestingly, the solid concentration effect was found in the process of sorption kinetics and sorption isotherms. The sorption kinetic curves of Cd(II) on PASP/CMPP were well-fitted by the quasi-second-order kinetics under different adsorbent concentrations. The adsorption conforms to Langmuir and Freundlich adsorption isotherm models. More importantly, PASP/CMPP composites are expected to be used as a new kind of environmental adsorbent for wastewater treatment.

Preparation and Characterization of a New Bis-Uracil Chitosan-Based Hydrogel as Efficient Adsorbent for Removal of Anionic Congo Red Dye

A new hydrogel, based on chitosan crosslinked with 2-chlorophenyl-bis(6-amino-1,3-dimethyluracil-5-yl) methane, (2Clph-BU-Cs), has been successfully created. Various instrumental techniques such as elemental analysis, FTIR, SEM, and XRD were used to prove its structure. Its removal efficiency for anionic Congo red (CR) dye under different conditions for industrial wastewater treatment was studied. For optimizing the conditions to maximize CR dye removal, the impacts of temperature, contact time, pH, and initial concentration of the dye on adsorption capacity were investigated. The removal of the dye was pH-dependent, with a much higher value achieved at pH 4 than at pH 7 and 9. The maximum adsorption capacity of the hydrogel was 93.46 mg g^-1. The model of adsorption process was fitted to the pseudo-second-order kinetic model. The intraparticle diffusion demonstrated the multi-step nature of the adsorption process. The thermodynamic results showed that the adsorption process was endothermic because of the positive value of enthalpy (43.70 kJ mol^-1). The process of adsorption at high temperatures was spontaneous, according to the values of ∆G⁰. An increase in randomness was seen in the value of ∆S°. Generally, the investigated hydrogel has the potential to be used as a promising effective reusable adsorbent for industrial wastewater remediation.

Design, Synthesis, and Characterization of Novel Bis-Uracil Chitosan Hydrogels Modified with Zinc Oxide Nanoparticles for Boosting Their Antimicrobial Activity

A new series of hydrogels was successfully prepared by incorporating various substituted bisuracil (R-BU) linkages between chitosan Schiff's base chains (R-BU-CsSB) and between chitosan chains (R-BU-Cs). After protection of the amino groups of chitosan by benzaldehyde, yielding chitosan Schiff's base (CsSB), the reaction with epichlorohydrin was confined on the -OH on C6 to produce epoxy chitosan Schiff's base (ECsSB), which was reacted with R-BU to form R-BU-CsSB hydrogels, and finally, the bioactive amino groups of chitosan were restored to obtain R-BU-Cs hydrogels. Further, some R-BU-Cs-based ZnO nanoparticle (R-BU-Cs/ZnONPs) composites were also prepared. Appropriate techniques such as elemental analysis, FTIR, XRD, SEM, and EDX were used to verify their structures. Their inhibition potency against all the tested microbes were arranged as: ZnONPs bio-composites > R-BU-Cs hydrogels > R-BU-CsSB hydrogels > Cs. Their inhibition performance against Gram-positive bacteria was better than Gram-negative ones. Their minimum inhibitory concentration (MIC) values decreased as a function of the negative resonance effect of the substituents in the aryl ring of R-BU linkages in the hydrogels. Compared with Vancomycin, the ZnONPs bio-composites showed superior inhibitory effects against most of the tested Gram-negative bacteria, all inspected Gram-positive ones, and all investigated fungi.

Chitosan-Functionalized-Graphene Oxide (GO@CS) Beads as an Effective Adsorbent to Remove Cationic Dye from Wastewater

In this study, the preparation of graphene oxide@chitosan (GO@CS) composite beads was investigated via continuous dropping techniques to remove methylene blue (MB)-dye from an aqueous media. The prepared beads were characterized using various techniques before and after the adsorption of MB. The experimental results showed that the adsorption processes fit the kinetic pseudo-second-order and Langmuir isotherm models. Moreover, the GO@CS beads achieve maximum adsorption capacities of 23.26 mg g⁻¹, which was comparable with other adsorbents in the literature. An important advantage of our adsorbent is that the GO@CS can remove 82.1% of the real sample color within 135 min.

Nanoclay- and TiO2 Nanoparticle-Modified Poly(N-vinyl pyrrolidone) Hydrogels: A Multifunctional Material for Application in Photocatalytic Degradation and Adsorption-Based Removal of Organic Contaminants

In recent times, access to clean water has become increasingly difficult and one of the most important problems for the sustainability of life due to environmental pollution. Based on this thought, in this study, a multifunctional hydrogel nanocomposite (nanoclay@TiO₂@PNVP) containing linear poly(N-vinyl pyrrolidone) (PNVP), nanoclay, and TiO₂ nanoparticles was synthesized and used as an adsorbent and photocatalyst for the adsorption-based and photocatalytic degradation-based removal of organic and pharmaceutical pollutants such as methylene blue (MB) and sildenafil citrate (SLD). The modification of the hydrogel with TiO₂ nanoparticles and nanoclay aimed to increase the adsorption capacity of the PNVP hydrogel as well as to gain photocatalytic properties for the effective removal of organic contaminants. This hybrid material, which can be cleaned in two different ways, can be reused and recycled at least 10 times. Characterization studies were carried out using Fourier transform infrared spectroscopy, scanning electron microscopy, Raman spectroscopy, thermogravimetric analysis, differential thermogravimetry, and viscosimetry techniques. Optimization studies for the adsorption-based removal of organic contaminants were carried out on MB and SLD as model organic compounds. The optimum parameters for MB were found at pH 10 of the sample solution when 50 mg of the nanoclay@TiO₂@PNVP hydrogel nanocomposite was used for 420 min of contact time. It was observed that 99% of the MB was photocatalytically degraded within 150 min at pH 10. Our material had multifunctional applicability properties, showing high adsorption and photocatalytic performances over 99% for at least 10 times of use. For the removal of organic and pharmaceutical contaminants from wastewater, the synthesized material can be used in two treatment processes separately or in combination in one step, providing an important advantage for its usability in environmental applications.

Evaluation of the antimicrobial and anti-biofilm activity of novel salicylhydrazido chitosan derivatives impregnated with titanium dioxide nanoparticles

Two novel chitosan derivatives were prepared by incorporating salicylhydrazide into chitosan Schiff base (SCsSB) and chitosan (SCs). Two nanocomposites, SCs/TiO₂-1% and SCs/TiO₂-3%, were also prepared. Their structures were confirmed using elemental analyses, FTIR, XRD, SEM, EDX and TEM. Their antimicrobial and anti-biofilm activities were arranged as: SCs/TiO₂-3% > SCs/TiO₂-1% > SCs > SCsSB > chitosan. SCs showed minimum inhibitory concentration (MIC) value of 1.95 μg/mL against A. niger which was comparable with that of Amphotericin B. SCs/TiO₂-3% showed higher inhibition against S. epidermidis, S. aureus, S. pyogenes, P. aeruginosa and E. coli than Vancomycin. While, it showed comparable inhibition activity to that of Vancomycin against B. subtilis and P. mirabilis. SCs/TiO₂-3% showed MIC values equal 0.48 and 0.98 μg/mL corresponded to 0.98 and 1.95 μg/mL of Amphotericin B against C. albicans, A. fumigatus and A. niger, respectively. SCs/TiO₂-3% showed much lower minimum biofilm inhibitory concentration (MBIC) values, ranged between 1.95 and 7.81 μg/mL, than those of SCs, ranged from 62.5 to 125 μg/mL. SCs/TiO₂-3% was safe on normal human cells. The modifiers and TiO₂ nanoparticles incorporated into chitosan in one structure developed its performance. It is approach for attaining appropriate structures which are good competitors for antimicrobial agents.

Evaluation of Antimicrobial and Anti-Biofilm Formation Activities of Novel Poly(vinyl alcohol) Hydrogels Reinforced with Crosslinked Chitosan and Silver Nano-Particles

Novel hydrogels were prepared by blending chitosan and poly(vinyl alcohol), PVA, then crosslinking the resulting blends using trimellitic anhydride isothiocyanate at a concentration based on chitosan content in the blends. The weight ratios of chitosan: PVA in the blends were 1:3, 1:1, and 3:1 to produce three hydrogels symbolized as H13, H11, and H31, respectively. For a comparison, H10 was also prepared by crosslinking pure chitosan with trimellitic anhydride isothiocyanate. For further modification, three H31/silver nanocomposites (AgNPs) were synthesized using three different concentrations of silver nitrate to obtain H31/AgNPs1%, H31/AgNPs3% and H31/AgNPs5%. The structures of the prepared samples were emphasized using various analytical techniques. PVA has no inhibition activity against the tested microbes and biofilms. The antimicrobial and anti-biofilm formation activities of the investigated samples was arranged as: H31/AgNPs5% ≥ H31/AgNPs3% > H31/AgNPs1% > H10 > H31 > H11 > H13 > chitosan. H31/AgNPs5% and H31/AgNPs3% were more potent than Vancomycin and Amphotericin B against most of the tested microbes. Interestingly, H31 and H31/AgNPs3% were safe on the normal human cells. Consequently, hydrogels resulting from crosslinked blends of chitosan and PVA loaded with AgNPs in the same structure have significantly reinforced the antimicrobial and inhibition activity against the biofilms of PVA.

Recent Developments in the Application of Bio-Waste-Derived Adsorbents for the Removal of Methylene Blue from Wastewater: A Review

Over the last few years, various industries have released wastewater containing high concentrations of dyes straight into the ecological system, which has become a major environmental problem (i.e., soil, groundwater, surface water pollution, etc.). The rapid growth of textile industries has created an alarming situation in which further deterioration to the environment has been caused due to substances being left in treated wastewater, including dyes. The application of activated carbon has recently been demonstrated to be a highly efficient technology in terms of removing methylene blue (MB) from wastewater. Agricultural waste, as well as animal-based and wood products, are excellent sources of bio-waste for MB remediation since they are extremely efficient, have high sorption capacities, and are renewable sources. Despite the fact that commercial activated carbon is a favored adsorbent for dye elimination, its extensive application is restricted because of its comparatively high cost, which has prompted researchers to investigate alternative sources of adsorbents that are non-conventional and more economical. The goal of this review article was to critically evaluate the accessible information on the characteristics of bio-waste-derived adsorbents for MB’s removal, as well as related parameters influencing the performance of this process. The review also highlighted the processing methods developed in previous studies. Regeneration processes, economic challenges, and the valorization of post-sorption materials were also discussed. This review is beneficial in terms of understanding recent advances in the status of biowaste-derived adsorbents, highlighting the accelerating need for the development of low-cost adsorbents and functioning as a precursor for large-scale system optimization.

Synthesis and Characterization of Novel Uracil-Modified Chitosan as a Promising Adsorbent for Efficient Removal of Congo Red Dye

Novel Uracil-modified chitosan (UCs) adsorbent has successfully been synthesized through a four-step method during which the amino groups of chitosan have been protected, then epoxy nuclei have been incorporated, afterwards the latter have been opened using 6-amino-1,3-dimethyl uracil, and finally the amino groups have been regained via removing the protection. Its structure was checked using FTIR, XRD and SEM techniques. The adsorption capacity of UCs for anionic Congo Red (CR) dye was studied under various conditions. It decreased significantly with increasing the solution pH value and dye concentration, while increased with increasing temperature. The adsorption of UCs for CR dye at different temperatures, solution pH and dye concentrations fitted to the kinetic model of pseudo-second order and Elovich model. The intraparticle diffusion model showed that the adsorption process involves multi-step process. The isotherm of CR dye adsorption by UCs conforms to the Langmuir isotherm model indicating the monolayer nature of adsorption. The maximum monolayer coverage capacity, q_max, was 434.78 mg g⁻¹. Studying the thermodynamic showed that the adsorption of CR dye onto UCs was endothermic as illustrated from the positive value of enthalpy (21.37 kJ mol⁻¹). According to the values of ΔG°, the adsorption process was spontaneous at all selected temperatures. The value of ΔS° showed an increase in randomness for the adsorption of CR dye by UCs. The value of activation energy was 18.40 kJ mol⁻¹.

Kinetics, Isotherm and Thermodynamic Studies for Efficient Adsorption of Congo Red Dye from Aqueous Solution onto Novel Cyanoguanidine-Modified Chitosan Adsorbent

Novel Cyanoguanidine-modified chitosan (CCs) adsorbent was successfully prepared via a four-step procedure; first by protection of the amino groups of chitosan, second by insertion of epoxide rings, third by opening the latter with cyanoguanidine, and fourth by restoring the amino groups through elimination of the protection. Its structure and morphology were checked using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The adsorption capacity of CCs for Congo Red (CR) dye was studied under various conditions. It decreased significantly with the increase in the solution pH value and dye concentration, while it increased with increasing temperature. The adsorption fitted to the pseudo-second order kinetic model and Elovich model. The intraparticle diffusion model showed that the adsorption involved a multi-step process. The isotherm of CR dye adsorption by CCs conforms to the Langmuir isotherm model, indicating the monolayer nature of adsorption. The maximum monolayer coverage capacity, q_max, was 666.67 mg g^-1. Studying the thermodynamic showed that the adsorption was endothermic as illustrated from the positive value of enthalpy (34.49 kJ mol^-1). According to the values of ΔG°, the adsorption process was spontaneous at all selected temperatures. The value of ΔS° showed an increase in randomness for the adsorption process. The value of activation energy was 2.47 kJ mol^-1. The desorption percentage reached to 58% after 5 cycles. This proved that CCs is an efficient and a promising adsorbent for the removal of CR dye from its aqueous solution.