Optimization of Chitosan Properties with the Aim of a Water Resistant Adhesive Development

Preparation and analysis of environment-friendly and high- performance cellulose-based wood adhesive

Conventional wood adhesives such as urea-formaldehyde (UF) resin, phenol-formaldehyde (PF) resin, melamine-formaldehyde (MF) resin, and melamine-urea-formaldehyde (MUF) resin have usually problems in formaldehyde emission and derived from petrochemical products, so developing green and environmentally friendly biomass-based wood adhesives has become a research topic of wide focus. As a biomaterial, cellulose (and its derivatives) is the largest bio-resource in the world, and developing its application in wood adhesives synthesis has outstanding raw material advantage. Therefore, in this study, a formaldehyde-free cellulose-based wood adhesive (OCHU) was prepared from carboxymethyl cellulose (CMC) by oxidizing with NaIO4 and then cross-linked with a laboratory synthetic polyurea compound (HU). The effect of oxidation time, oxidation temperature, NaIO4, and HU addition on the structures and properties of OCHU adhesive was investigated. The results showed that the adhesive OCHU prepared in 20 % (w/w based on CMC) of NaIO4 oxidized CMC at 50 °C for 8 h, and then polymerized with HU of equal mass to CMC presents excellent bonding performance. The dry strength, 24 h cold water and 3 h hot water (63 °C) soaking wet strength of its bonded plywood are as high as 1.98 MPa, 1.18 MPa, and 1.40 MPa, respectively, which conformed to the standard requirements in Chinese national standard GB/T 17657-2013. This work provides an effective scheme for preparing cellulose-based wood adhesives with high bonding strength, water resistance, and environmental friendliness. Thus this prepared OCHU adhesive has broad industrial application potential in preparing high-performance plywood.

Comparative analysis of binder polymer matrices for developing green pH-responsive indicating ink solutions based on anthocyanin for food packaging applications

Traditional packaging ink solutions comprise organic solvents and petrochemical-derived materials, which are environmentally hazardous and highly harmful to human health. Therefore, the demand for novel, green, sustainable packaging ink solutions is increasing. Anthocyanin-based indicating ink solutions were prepared by varying the types and amounts of binders, and their properties were analyzed. The binder affected the chemical bonding, thermal stability, contact angle, and viscosity of the ink solution. The viscosity influenced the coating thickness, reactivity, and color. Ink solutions based on carboxymethyl cellulose (CMC) and chitosan (CT) displayed significant changes in viscosity (35.45-1387.63 mPa·s), exhibiting shear-thinning and thixotropic behaviors, which are excellent characteristics for ink solutions. During kimchi fermentation, the total color difference ranged from a minimum of 6.38 to a maximum of 22.04, demonstrating excellent indicating performance. CMC and CT displayed high potential for use as binders in anthocyanin-based, pH-responsive indicating ink solutions for application in food packaging.

A Novel Bio-Adhesive Based on Chitosan-Polydopamine-Xanthan Gum for Glass, Cardboard and Textile Commodities

The escalating environmental concerns associated with petroleum-based adhesives have spurred an urgent need for sustainable alternatives. Chitosan, a natural polysaccharide, is a promising candidate; however, its limited water resistance hinders broader application. The aim of this study is to develop a new chitosan-based adhesive with improved properties. The polydopamine association with chitosan presents a significant increase in adhesiveness compared to pure chitosan. Polydopamine is synthesized by the enzymatic action of laccase from Trametes versicolor at pH = 4.5, in the absence or presence of chitosan. This pH facilitates chitosan's solubility and the occurrence of catechol in its reduced form (pH < 5.5), thereby increasing the final adhesive properties. To further enhance the adhesive properties, various crosslinking agents were tested. A multi-technique approach was used for the characterization of formulations. The formulation based on 3% chitosan, 50% polydopamine, and 3% xanthan gum showed a spectacular increase in adhesive properties when tested on glass, cardboard and textile. This formulation increased water resistance, maintaining the adhesion of a sample soaked in water for up to 10 h. For cardboard and textile, material rapture occurred, in mechanical tests, prior to adhesive bond failure. Furthermore, all the samples showed antiflame properties, expanding the benefits of their use. Comparison with commercial glues confirms the remarkable adhesive properties of the new formulation.

Antibacterial adhesive based on oxidized tannic acid-chitosan for rapid hemostasis

Currently, bacterial infections and bleeding interfere with wound healing, and multifunctional hydrogels with appropriate blood homeostasis, skin adhesion, and antibacterial activity are desirable. In this study, chitosan-based hydrogels were synthesized using oxidized tannic acid (OTA) and Fe3+ as cross-linkers (CS-OTA-Fe) by forming covalent, non-covalent, and metal coordination bonds between Fe3+ and OTA. Our results demonstrated that CS-OTA-Fe hydrogels showed antibacterial properties against Gram-positive bacteria (Staphylococcus aureus)and Gram-negative bacteria (Escherichia coli), low hemolysis rate (< 2 %), rapid blood clotting ability, in vitro (< 2 min), and in vivo (90 s) in mouse liver bleeding. Additionally, increasing the chitosan concentration from 3 wt% to 4.5 wt% enhanced cross-linking in the network, leading to a significant improvement in the strength (from 106 ± 8 kPa to 168 ± 12 kPa) and compressive modulus (from 50 ± 9 kPa to 102 ± 14 kPa) of hydrogels. Moreover, CS-OTA-Fe hydrogels revealed significant adhesive strength (87 ± 8 kPa) to the cow's skin tissue and cytocompatibility against L929 fibroblasts. Overall, multifunctional CS-OTA-Fe hydrogels with tunable mechanical properties, excellent tissue adhesive, self-healing ability, good cytocompatibility, and fast hemostasis and antibacterial properties could be promising candidates for biomedical applications.

An eco-friendly chitosan-genipin/SiO2 composite for reactive orange 16 dye removal: Insights into adsorption statistical modeling and mechanism

The present work develops an effective bioadsorbent of cross-linked chitosan-genipin/SiO2 adsorbent (CHI-GNP/SiO2). The developed CHI-GNP/SiO2 was employed for the removal of organic dye (reactive orange 16, RO16) from simulated wastewater. The optimization of the fundamental adsorption variables (CHI-GNP/SiO2 dose, time, and pH) via the Box-Behnken design (BBD) was attained for achieving maximal adsorption capacity and high removal efficiency. The good agreement between the Freundlich isotherms and empirical data of RO16 adsorption by CHI-GNP/SiO2 indicates that the adsorption process follows a multilayer adsorption mechanism. The reasonable agreement between the pseudo-second-order model and the kinetic data of RO16 adsorption by CHI-GNP/SiO2 was obtained. The maximum RO16 adsorption capacity (qmax) of CHI-GNP/SiO2 was identified to be 57.1 mg/g. The adsorption capacity of CHI-GNP/SiO2 is attributed to its unique surface properties, including its highly porous structure and the presence of functional groups such as amino and hydroxyl groups. According to the results of this investigation, CHI-GNP/SiO2 has the potential to be an adsorbent for the removal of acidic dyes from wastewater.

Chitosan Polysaccharides from a Polarizable Multiscale Approach

We report simulations of chitosan polysaccharides in the aqueous phase, at infinite dilute conditions and zero ionic strength. Those simulations are performed by means of a polarizable multiscale modeling scheme that relies on a polarizable all atom force field to model solutes and on a polarizable solvent coarse grained approach. Force field parameters are assigned only from quantum chemistry ab initio data. We simulate chitosan monomer units, dimers and 50-long chains. Regarding the 50-long chains we simulate three sets of ten randomly built chain replica at three different pH conditions (corresponding to different chain protonation states, the chain degree of deacetylation is 85%). Our simulations show the persistence length of 50-long chitosan chains at strong acidic conditions (pH <5) to be 24 ± 2 nm (at weak/negligible ionic strength conditions), and to be 1 order of magnitude shorter at usual pH conditions. Our simulation data support the most recent simulation and experimental studies devoted to chitosan polysaccharides in the aqueous phase.

Synthesis and Characterization of Thermoresponsive Chitosan-graft-poly(N-isopropylacrylamide) Copolymers

Thermoresponsive chitosan-graft-poly(N-isopropylacrylamide) (CS-g-PNIPAAm) copolymers of different composition were synthesized by free-radical polymerization of chitosan (CS) and N-isopropylacrylamide (NIPAAm) in aqueous solution using potassium persulfate (PPS) as an initiator. By changing the molar ratio of CS:NIPAAm from 1:0.25 to 1:10 graft copolymers with a CS backbone and different amounts of PNIPAM side chains were prepared. The chemical structure of the obtained CS-g-PNIPAAm copolymers was confirmed by FTIR and 1H NMR spectroscopy. 1H NMR spectra were also used to calculate the content of attached PNIPAAm side chains. Moreover, the lower critical solution temperature (LCST) behavior of synthesized copolymers was assessed by cloud point, differential scanning calorimetry and particle size measurements. The aqueous solutions of copolymers containing ≥12 molar percent of PNIPAAm side chains demonstrated LCST behavior with the phase separation at around 29.0-32.7 °C. The intensity of thermoresponsiveness depended on the composition of copolymers and increased with increasing content of poly(N-isopropylacrylamide) moieties. The synthesized thermoresponsive chitosan-graft-poly(N-isopropylacrylamide) copolymers could be potentially applied in drug delivery systems or tissue engineering.

Chitosan-tannin adhesive: Fully biomass, synthesis-free and high performance for bamboo-based composite bonding

Inspired by phenol-amine chemistry of mussels, a synthesis-free and fully biomass adhesive composed of chitosan and tannin (CST) was successfully developed by a facile method. The performance of CST adhesive for bonding bamboo, wood and bamboo-wood substrates were tested. When 160 °C hot-press temperature was used, dry lap shear strength above 5.00 MPa was obtained. The CST adhesive has remarkable water resistance and low cure temperature as high wet shear strength of 2.37 MPa for plybamboo specimens was achieved after 3 h boiling in water even though low hot-press temperature of 100 °C was applied. Further, high strength of 1.78 MPa remained after 72 h boiling. With higher hot-press temperatures used, wet shear strength above 3.60 MPa was achieved. The adhesion performance for wood substrate was also superior to other phenol-amine adhesives reported in literatures. The bamboo-wood composites assembled with CST adhesive show excellent mechanical performance, specifically modulus of rupture (MOR) of 100-133 MPa and modulus of elasticity (MOE) of 10-13 GPa were achieved with different hot-press temperatures used. Given the advantages including outstanding water resistance, facile preparation, fully biomass, and low cure temperature, CST adhesive exhibited great potential to be an ideal alternative to formaldehyde-based resin for wood and bamboo bonding.

Synergic chitin degradation by Streptomyces sp. SCUT-3 chitinases and their applications in chitinous waste recycling and pathogenic fungi biocontrol

The genus Streptomyces comprises the most important chitin decomposers in soil and revealing their chitinolytic machinery is beneficial for the conversion of chitinous wastes. Streptomyces sp. SCUT-3, a chitin-hydrolyzing and a robust feather-degrading bacterium, was isolated previously. The potential chitin-degrading enzymes produced by SCUT-3 were analyzed in the present study. Among these enzymes, three chitinases were successfully expressed in Pichia pastoris at comparatively high yields of 4.8 U/mL (SsExoChi18A), 11.2 U/mL (SsExoChi18B), and 17.8 U/mL (SsEndoChi19). Conserved motifs and constructive 3D structures of these three exo- and endochitinases were also analyzed. These chitinases hydrolyzed colloidal chitin to chitin oligomers. SsExoChi18A showed apparent synergic effects with SsEndoChi19 in colloidal chitin and shrimp shell hydrolysis, with an improvement of 29.3 % and 124.9 %, respectively. Compared with SsExoChi18B and SsEndoChi19, SsExoChi18A exhibited the strongest antifungal effects against four plant pathogens by inhibiting mycelial growth and spore germination. This study provided good candidates for chitinous waste-processing enzymes and antifungal biocontrol agents. These synergic chitin-degrading enzymes of SCUT-3 are good targets for its further genetical modification to construct super chitinous waste-degrading bacteria with strong abilities to hydrolyze both protein and chitin, thereby providing a direction for the future path of the chitinous waste recycling industry.

Chitosan-Based Carbon Dots with Applied Aspects: New Frontiers of International Interest in a Material of Marine Origin

Carbon dots (CDs) have attracted significant research attention worldwide due to their unique properties and advantageous attributes, such as superior optical properties, biocompatibility, easy surface functionalization, and more. Moreover, biomass-derived CDs have attracted much attention because of their additional advantages related to more environmentally friendly and lower-cost synthesis. In this respect, chitosan has been recently explored for the preparation of CDs, which in comparison to other natural precursors exhibited additional advantages. Beyond the benefits related to the eco-friendly and abundant nature of chitosan, using it as a nanomaterial precursor offers additional benefits in terms of structure, morphology, and dopant elements. Furthermore, the high content of nitrogen in chitosan allows it to be used as a single carbon and nitrogen precursor for the preparation of N-doped CDs, significantly improving their fluorescent properties and, therefore, their performances. This review addresses the most recent advances in chitosan-based CDs with a special focus on synthesis methods, enhanced properties, and their applications in different fields, including biomedicine, the environment, and food packaging. Finally, this work also addresses the key challenges to be overcome to propose future perspectives and research to unlock their great potential for practical applications.

A Review of the Chemical Extraction of Chitosan from Shrimp Wastes and Prediction of Factors Affecting Chitosan Yield by Using an Artificial Neural Network

There are two viable options to produce shrimp shells as by-product waste, either within the shrimp production phases or when the shrimp are peeled before cooking by the end user. This waste is considered a double-edged sword, as it is possible to be either a source of environmental pollution, through dumping and burning, or a promising source from which to produce chitosan as a biodegradable, biocompatible biopolymer which has a variety of agricultural, industrial, and biomedical applications. Chitosan is a deacetylated form of chitin that can be chemically recovered from shrimp shells through the three sequential stages of demineralization, deproteinization, and deacetylation. The main aim of this review paper is to summarize the recent literature on the chemical extraction of chitosan from shrimp shells and to represent the physicochemical properties of chitosan extracted from shrimp shells in different articles, such as chitosan yield, moisture content, solubility, ash content, and degree of deacetylation. Another aim is to analyze the influence of the main predictors of the chemical extraction stages (demineralization, deproteinization, and deacetylation) on the chitosan yield percentage by using a multilayer perceptron artificial neural network. This study showed that the deacetylation alkali concentration is the most crucial parameter, followed by the concentrations of acid and alkali of demineralization and deproteinization, respectively. The current review was conducted to be used in prospective studies for optimizing the chemical extraction of chitosan from shrimp wastes.

Production of Fungal Nanochitosan Using High-Pressure Water Jet System for Biomedical Applications

In this present work, fungal nanochitosans, with very interesting particle size distribution of 22 µm, were efficiently generated in high-yield production using a high-pressure water jet system (Star Burst System, Sugino, Japan) after 10 passes of mechanical treatment under high pressure. The specific characterization of fungal chitosan nanofibers suspensions in water revealed a high viscosity of 1450 mPa.s and an estimated transparency of 43.5% after 10 passes of fibrillation mechanical treatment. The mechanical characterization of fungal nanochitosan (NC) film are very interesting for medical applications with a Young’s modulus (E), a tensile strength (TS), and elongation at break (e%) estimated at 2950 MPa, 50.5 MPa, and 5.5%, respectively. Furthermore, we exhibited that the fungal nanochitosan (NC) film presented very good long-term antioxidant effect (reached 82.4% after 96 h of contact with DPPH radical solution) and very interesting antimicrobial activity when the nanochitosan (NC) fibers are mainly activated as NC-NH3+ form at the surface of the film with 45% reduction and 75% reduction observed for S. aureus (Gram-positive) and E. coli (Gram-negative), respectively, after 6 h of treatment. These promising antimicrobial and antioxidant activities indicated the high potential of valorization toward biomedical applications.