Hydrothermal Ageing Effect on Reinforcement Efficiency of Nanofibrillated Cellulose/Biobased Poly(butylene succinate) Composites

Biodegradable Poly(butylene succinate) Laminate with Nanocellulose Interphase Layer for High-Barrier Packaging Film Application

In response to rising concerns over the environmental and human health ramifications of polymers derived from petroleum, particularly in the food packaging industry, research has pivoted towards more sustainable materials. Poly(butylene succinate) (PBS), selected as the polymer matrix, stands out as one of the most promising bio-based and biodegradable polymers suitable for film blowing and lamination. A layered spray-coating technique was employed to apply 1, 5, 10, and 20 layers of nanofibrillated cellulose (NFC) between blown PBS films, creating a three-layer laminate structure. NFC sourced from minimally processed hemp stalk waste highlights the potential for minimizing environmental impact. The water vapor transmission rate (WVTR) of these films, a critical parameter for food packaging, was assessed in a controlled environment at 38 °C and 90% relative humidity over a period of two months. The integration of a single NFC layer, constituting 0.35% of the composite's weight, was observed to significantly reduce the WVTR by up to 5.5-fold. It was noted that higher NFC layer counts above 10 reduced the adhesion within the laminate layers. Morphological assessments showed that the number of structural defects increased with a higher count of NFC layers. As the count of NFC layers increased, the optical transparency of the laminates dropped from approximately 65% to 25% in the visible light spectrum. Notably, by weight percent, NFC proved to be an effective barrier even without chemical modification. The developed laminates stand out as a viable, green option for food packaging, offering a sustainable and renewable solution.

Preparation and Spectroscopic, Thermal, and Mechanical Characterization of Biocomposites of Poly(butylene succinate) and Onion Peels or Durum Wheat Bran

The utilization of plant based fillers: onion peels (OP) and durum wheat bran (WB) to obtain sustainable biocomposite materials with poly(butylene succinate) (PBS) is presented in this paper. The biocomposites were first obtained in pellet form by extrusion method and then injection moldings were made from the pellets. Two kinds of biocomposites were fabricated containing 15% and 30% wt. of OP or WB. Additionally, pure PBS moldings were prepared for comparative purposes. The effect of the filler type and its amount on the chemical structure, density, thermal, and thermo-mechanical properties of the fabricated composite samples was studied. Fourier-transform infrared spectroscopy results showed that the composite preparation method had no effect on the chemical structure of composite components, but weak interactions such as hydrogen bonding between OP or WB and PBS was observed. The addition of OP or WB to the composite with PBS reduced its thermal stability in comparison with pure PBS, all studied composites start to degrade below 290 °C. Additionally, the mechanical properties of the composites are worse than PBS, as the impact strength dropped by about 70%. The deterioration of tensile strength was in the range 20-47%, and the elongation at maximum load of the composites was in the range 9.22-3.42%, whereas for pure PBS it was 16.75%. On the other hand, the crystallinity degree increased from 63% for pure PBS to 79% for composite with 30% wt. of WB. The Young's modulus increased to 160% for composition with 30% wt. of OP. Additionally, the hardness of the composites was slightly higher than PBS and was in the range 38.2-48.7 MPa. Despite the reduction in thermal stability and some mechanical properties, the studied composites show promise for everyday object production.

Blending of Low-Density Polyethylene and Poly(Butylene Succinate) (LDPE/PBS) with Polyethylene-Graft-Maleic Anhydride (PE-g-MA) as a Compatibilizer on the Phase Morphology, Mechanical and Thermal Properties

It is of significant concern that the buildup of non-biodegradable plastic waste in the environment may result in long-term issues with the environment, the economy and waste management. In this study, low-density polyethylene (LDPE) was compounded with different contents of poly(butylene succinate) (PBS) at 10-50 wt.%, to evaluate the potential of replacing commercial plastics with a biodegradable renewable polymer, PBS for packaging applications. The morphological, mechanical and thermal properties of the LDPE/PBS blends were examined in relation to the effect of polyethylene-graft-maleic anhydride (PE-g-MA) as a compatibilizer. LDPE/PBS/PE-g-MA blends were fabricated via the melt blending method using an internal mixer and then were compression molded into test samples. The presence of LDPE, PBS and PE-g-MA individually in the matrix for each blend presented physical interaction between the constituents, as shown by Fourier-transform infrared spectroscopy (FTIR). The morphology of LDPE/PBS/PE-g-MA blends showed improved compatibility and homogeneity between the LDPE matrix and PBS phase. Compatibilized LDPE/PBS blends showed an improvement in the tensile strength, with 5 phr of compatibilizer providing the optimal content. The thermal stability of LDPE/PBS blends decreased with higher PBS content and the thermal stability of compatibilized blends was higher in contrast to the uncompatibilized blends. Therefore, our research demonstrated that the partial substitution of LDPE with a biodegradable PBS and the incorporation of the PE-g-MA compatibilizer could develop an innovative blend with improved structural, mechanical and thermal properties.

Environmental Effects on Strength and Failure Strain Distributions of Sheep Wool Fibers

Sheep wool is an eco-friendly, renewable, and totally recyclable material increasingly used in textiles, filters, insulation, and building materials. Recently, wool fibers have become good alternatives for reinforcement of polymer composites and filaments for 3D printing. Wool fibers are susceptible to environmental degradation that could shorten their lifetime and limit applications. This study reports on the mechanical properties of sheep wool fibers under the impact of humid air and UV irradiation. The results of single fiber tensile tests showed a noticeable gauge length effect on the fibers’ strength and failure strain. Long (50 mm) fibers possessed about 40% lower characteristics than short (10 mm) fibers. Environmental aging decreased the elastic modulus and strength of the fibers. Moisture-saturated fibers possessed up to 43% lower characteristics, while UV aging resulted in up to a twofold reduction of the strength. The most severe degradation effect is observed under the coupled influence of UVs and moisture. The two-parameter Weibull distribution was applied for the fiber strength and failure strain statistical assessment. The model well predicted the gauge length effects. Moisture-saturated and UV-aged fibers were characterized by less extensive strength dependences on the fiber length. The strength and failure strain distributions of aged fibers were horizontally shifted to lower values. The results will contribute to be reliable predictions of the environmental durability of sheep wool fibers and will extend their use in technical applications.

Carbon Fiber/PLA Recycled Composite

Due exceptional properties such as its high-temperature resistance, mechanical characteristics, and relatively lower price, the demand for carbon fiber has been increasing over the past years. The widespread use of carbon-fiber-reinforced polymers or plastics (CFRP) has attracted many industries. However, on the other hand, the increasing demand for carbon fibers has created a waste recycling problem that must be overcome. In this context, increasing plastic waste from the new 3D printing technology has been increased, contributing to a greater need for recycling efforts. This research aims to produce a recycled composite made from different carbon fiber leftover resources to reinforce the increasing waste of Polylactic acid (PLA) as a promising solution to the growing demand for both materials. Two types of leftover carbon fiber waste from domestic industries are handled: carbon fiber waste (CF) and carbon fiber-reinforced composite (CFRP). Two strategies are adopted to produce the recycled composite material, mixing PLA waste with CF one time and with CFRP the second time. The recycled composites are tested under tensile test conditions to investigate the impact of the waste carbon reinforcement on PLA properties. Additionally, thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier-transformed infrared spectroscopy (FTIR) is carried out on composites to study their thermal properties.