Influence of Dimethacrylate Monomer on the Polymerization Efficacy of Resin-Based Dental Cements-FTIR Analysis

Assessment of Degree of Conversion and Volumetric Shrinkage of Novel Self-Adhesive Cement

The degree of monomer conversion and polymerization shrinkage are two of the main reasons for potential adhesion failure between the tooth structure and the restoration substrate. To evaluate the degree of conversion and polymerization shrinkage of a newly developed self-adhesive resin cement, the degree of conversion (DC) was measured using FTIR under different activation modes, temperatures, and times. Volumetric shrinkage was tested using the AcuVol video imaging method. The experimental cement showed a higher DC than other cements under self-curing. The DC of the experimental cement was higher than that of other cements, except SpeedCem Plus under light curing. The experimental cement had a higher DC than other cements, except SpeedCem Plus in some conditions under dual curing. All self-adhesive cements had a higher DC at 37 °C than at 23 °C under self-curing, and there was no statistical difference between 23 °C and 37 °C under light curing. All self-adhesive cements showed a significantly higher DC at 10 min than at 5 min under self-curing. There was no statistical difference between 5 min and 10 min for most cements under dual curing. All self-adhesive cements statistically had the same volumetric shrinkage under light curing and self-curing. The newly developed self-adhesive resin cement exhibited a higher degree of conversion and similar volumetric shrinkage compared to these commercial self-adhesive resin cements.

Dental Resin-Based Luting Materials-Review

As cementation represents the last stage of the work involved in making various indirect restorations (metal ceramic crowns and bridges, full ceramic crowns and bridges, inlays, onlays, and fiber posts), its quality significantly contributes to the clinical success of the therapy performed. In the last two decades, the demand for ceramic indirect restorations in everyday dental practice has considerably increased primarily due to the growing significance of esthetics among patients, but also as a result of hypersensitivity reactions to dental alloys in some individuals. In this context, it is essential to ensure a permanent and reliable adhesive bond between the indirect restoration and the tooth structure, as this is the key to the success of aesthetic restorations. Resin-based luting materials benefit from excellent optical (aesthetic) and mechanical properties, as well as from providing a strong and durable adhesive bond between the restoration and the tooth. For this reason, resin cements are a reliable choice of material for cementing polycrystalline ceramic restorations. The current dental material market offers a wide range of resin cement with diverse and continually advancing properties. In response, we wish to note that the interest in the properties of resin-based cements among clinicians has existed for many years. Yet, despite extensive research on the subject and the resulting continued improvements in the quality of these materials, there is still no ideal resin-based cement on the market. The manuscript authors were guided by this fact when writing the article content, as the aim was to provide a concise overview of the composition, properties, and current trends, as well as some future guidelines for research in this field that would be beneficial for dental practitioners as well as the scientific community. It is extremely important to provide reliable and succinct information and guidelines for resin luting materials for dental dental practitioners.

Determination of the degree of conversion, the diffuse reflectance, and the color stability after different aging processes of gingiva-colored composite resins

PURPOSE

To determine the degree of conversion (DC) and spectral diffuse reflectance of four different gingiva-colored composites and to evaluate their color stability after various aging processes.

MATERIALS AND METHODS

The gingiva-colored composites were assigned to four experimental groups (Anaxgum (AG), Crea.lign paste Gum (CB), Gradia Gum (GR), SR Nexco Gum (NC)). A total of 120 disc-shaped specimens (10 × 2 mm) (n = 30/group) were polymerized in a Teflon mold. The nature of chemical bonding was studied by Fourier transform infrared spectroscopy (FTIR). Diffuse reflection spectra of the polymerized specimens were gathered using an ultraviolet-visible-near infrared (UV-Vis-NIR) spectrophotometer. Specimens subjected to aging methods were divided into three subgroups (n = 10): ultraviolet aging, hydrothermal aging, and autoclave aging. Color differences (ΔE*ab and ΔE00 ) were determined by colorimetry before and after aging. The statistical analysis was done using a two-way ANOVA along with paired sample t-test and Bonferroni's post hoc test.

RESULTS

Conversion degrees varied between 26.9% and 59.7% and all groups showed 3 or 4 maxima at different positions in the visible region of the spectrum. Both ΔE*ab and ΔE00 values were significantly different from the groups of different brands for all types of aging processes. Similarly, there were significantly different ΔE*ab and ΔE00 values according to the aging procedure for all groups of particular brands, except for ΔE00 of SR Nexco Gum (NC).

CONCLUSIONS

The aging procedures resulted in significant color differences between similar shades of four commercial gingiva-colored composites. The composite resins showed different degrees of conversion and diffuse reflectance spectra. The aging conditions tested affected the color stability. Patients with gingiva-colored indirect restorations should be informed about time-dependent discoloration.

Development of Light-Polymerized Dental Composite Resin Reinforced with Electrospun Polyamide Layers

As the mechanical properties of resin-based dental composite materials are highly relevant in clinical practice, diverse strategies for their potential enhancement have been proposed in the extant literature, aiming to facilitate their reliable use in dental medicine. In this context, the focus is primarily given to the mechanical properties with the greatest influence on clinical success, i.e., the longevity of the filling in the patient's mouth and its ability to withstand very strong masticatory forces. Guided by these objectives, the goal of the present study was to ascertain whether the reinforcement of dental composite resins with electrospun polyamide (PA) nanofibers would improve the mechanical strength of dental restoration materials. For this purpose, light-cure dental composite resins were interspersed with one and two layers comprising PA nanofibers in order to investigate the influence of such reinforcement on the mechanical properties of the resulting hybrid resins. One set of the obtained samples was investigated as prepared, while another set was immersed in artificial saliva for 14 days and was subsequently subjected to the same set of analyses, namely Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). Findings yielded by the FTIR analysis confirmed the structure of the produced dental composite resin material. They also provided evidence that, while the presence of PA nanofibers did not influence the curing process, it strengthened the dental composite resin. Moreover, flexural strength measurements revealed that the inclusion of a 16 μm-thick PA nanolayer enabled the dental composite resin to withstand a load of 3.2 MPa. These findings were supported by the SEM results, which further indicated that immersing the resin in saline solution resulted in a more compact composite material structure. Finally, DSC results indicated that as-prepared as well as saline-treated reinforced samples had a lower glass transition temperature (Tg) compared to pure resin. Specifically, while pure resin had a Tg of 61.6 °C, each additional PA nanolayer decreased the Tg by about 2 °C, while the further reduction was obtained when samples were immersed in saline for 14 days. These results show that electrospinning is a facile method for producing different nanofibers that can be incorporated into resin-based dental composite materials to modify their mechanical properties. Moreover, while their inclusion strengthens the resin-based dental composite materials, it does not affect the course and outcome of the polymerization reaction, which is an important factor for their use in clinical practice.

Influence of carbon and graphene oxide nanoparticle on the adhesive properties of dentin bonding polymer: A SEM, EDX, FTIR study

OBJECTIVE

This study was aimed at including 2.5 wt.% of carbon nanoparticles (CNPs) and graphene oxide NPs (GNPs) in a control adhesive (CA) and then investigate the effect of this inclusion on their mechanical properties and its adhesion to root dentin.

MATERIALS AND METHODS

Scanning electron microscopy and energy dispersive X-ray (SEM-EDX) mapping were conducted to investigate the structural features and elemental distribution of CNPs and GNPs, respectively. These NPs were further characterized by Raman spectroscopy. The adhesives were characterized by evaluating their push-out bond strength (PBS), rheological properties, degree of conversion (DC) investigation, and failure type analysis.

RESULTS

The SEM micrographs revealed that the CNPs were irregular and hexagonal, whereas the GNPs were flake-shaped. EDX analysis showed that carbon (C), oxygen (O), and zirconia (Zr) were found in the CNPs, while the GNPs were composed of C and O. The Raman spectra for CNPs and GNPs revealed their characteristic bands (CNPs-D band: 1334 cm^-1, GNPs-D band: 1341 cm^-1, CNPs-G band: 1650 cm^-1, and GNPs-G band: 1607 cm^-1). The testing verified that the highest bond strength to root dentin were detected for GNP-reinforced adhesive (33.20 ± 3.55 MPa), trailed closely by CNP-reinforced adhesive (30.48 ± 3.10 MPa), while, the CA displayed lowest values (25.11 ± 3.60 MPa). The inter-group comparisons of the NP-reinforced adhesives with the CA revealed statistically significant results (p < 0.01). Failures of adhesive nature were most common in within the adhesives and root dentin. The rheological assessment results demonstrated a reduced viscosity for all the adhesives observed at advanced angular frequencies. All the adhesives verified suitable dentin interaction shown by hybrid layer and appropriate resin tag development. A reduced DC was perceived for both NP-reinforced adhesives, compared to the CA.

CONCLUSION

The present study's findings have demonstrated that 2.5% GNP adhesive revealed the highest, suitable root dentin interaction, and acceptable rheological properties. Nevertheless, a reduced DC was observed (matched with the CA). Prospective studies probing the influence of diverse concentrations of filler NPs on the adhesive's mechanical properties to root dentin are recommended.

pH-Responsive Hyperbranched Polymer Nanoparticles to Combat Intracellular Infection by Disrupting Bacterial Wall and Regulating Macrophage Polarization

Intracellular bacterial infections pose a serious threat to public health. Macrophages are a heterogeneous population of immune cells that play a vital role in intracellular bacterial infection. However, bacteria that survive inside macrophages could subvert the cell signaling and eventually reduce the antimicrobial activity of macrophages. Herein, dual pH-responsive polymer (poly[(3-phenylprop-2-ene-1,1-diyl)bis(oxy)bis(enthane-2,1-diyl)diacrylate-co-N-aminoethylpiperazine] (PCA)) nanoparticles were developed to clear intracellular bacteria by activating macrophages and destructing bacterial walls. The presence of acid-labile acetal linkages and tertiary amine groups in the polymer's backbone endow hyperbranched PCA dual pH-response activity that shows acid-induced positive charge increase and cinnamaldehyde release properties. The biodegraded PCA nanoparticles could significantly inhibit the growth of bacteria by damaging the bacterial walls. Meanwhile, PCA nanoparticles could uptake by macrophages, generate reactive oxygen species (ROS), and remodel the immune response by upregulating M1 polarization, leading to the reinforced antimicrobial capacity. Furthermore, PCA nanoparticles could promote bacteria-infected wound healing in vivo. Therefore, these dual pH-responsive PCA nanoparticles enabling bacteria-killing and macrophage activation provide a novel outlook for treating intracellular infection.

Effects of Sr/F-Bioactive Glass Nanoparticles and Calcium Phosphate on Monomer Conversion, Biaxial Flexural Strength, Surface Microhardness, Mass/Volume Changes, and Color Stability of Dual-Cured Dental Composites for Core Build-Up Materials

This study prepared composites for core build-up containing Sr/F bioactive glass nanoparticles (Sr/F-BGNPs) and monocalcium phosphate monohydrate (MCPM) to prevent dental caries. The effect of the additives on the physical/mechanical properties of the materials was examined. Dual-cured resin composites were prepared using dimethacrylate monomers with added Sr/F-BGNPs (5 or 10 wt%) and MCPM (3 or 6 wt%). The additives reduced the light-activated monomer conversion by ~10%, but their effect on the conversion upon self-curing was negligible. The conversions of light-curing or self-curing polymerization of the experimental materials were greater than that of the commercial material. The additives reduced biaxial flexural strength (191 to 155 MPa), modulus (4.4 to 3.3), and surface microhardness (53 to 45 VHN). These values were comparable to that of the commercial material or within the acceptable range of the standard. The changes in the experimental composites’ mass and volume (~1%) were similar to that of the commercial comparison. The color change of the commercial material (1.0) was lower than that of the experimental composites (1.5–5.8). The addition of Sr/F-BGNPs and MCPM negatively affected the physical/mechanical properties of the composites, but the results were satisfactory except for color stability.