Recent Insights into Lignocellulosic Biomass Pyrolysis: A Critical Review on Pretreatment, Characterization, and Products Upgrading

Continuous rotary kiln pyrolysis of cassava plant shoot system and wide speciation of oxygenated and nitrogen-containing compounds in bio-oil by HESI and APPI-Orbitrap MS

This work proposes the pyrolysis of the cassava plant shoot system biomass and a comprehensive chemical characterization of the resulting bio-oil. The highest yields of liquid products were obtained at 600 °C, with 12.6 % bio-oil (organic fraction), which presented the lowest total acid number of 65.7 mg KOH g-1. The bio-oil produced at 500 °C exhibited the highest total phenolic content of approximately 41 % GAE, confirmed by GC/MS analysis (33.8 % of the total area). FT-Orbitrap MS analysis found hundreds of oxygenated constituents in the bio-oils, belonging to the O2-7 classes, as well as nitrogen compounds from the Ny and OxNy classes. Higher pyrolysis temperatures resulted in more oxygenated phenolics (O4-7) undergoing secondary degradation and deoxygenation reactions, generating O2-3 compounds. Additional classes affected were O3-5N2-3, while O1-2N1 presented more stable compounds. These findings show that cassava bio-oils are promising sources of renewable chemicals.

Separation of lignin derivatives from hemp fiber using supercritical CO2, ethanol, and water at different temperatures

The process of lignin extraction often involves intricate chemical transformations, influencing its potential for high-value utilization. By investigating the process of lignin derivatives extraction from hemp fibers using supercritical CO2, ethanol, and water, we identified the relationship between the chemical structure of lignin derivatives and temperature. This discovery contributes to controlling the chemical structure of lignin derivatives through temperature modulation. We observed that lignin derivatives extracted within the temperature range of 100-120 °C exhibited the lowest average molecular weight and polydispersity index, presenting a disordered microstructure with the highest hydroxyl content. Lignin derivatives extracted between 140 and 160 °C showed an increase in average molecular weight and polydispersity index, decreased hydroxyl content, and a gradual transformation of microstructure into spherical particles. At 180 °C, the average molecular weight and polydispersity index of lignin derivatives decreased, the microstructure of lignin derivatives showed fewer spherical particles, while its hydroxyl content exhibited a partial recovery. Chemical analysis revealed a lower degree of condensation in lignin derivatives at 100-120 °C. Between 120 and 160 °C, the degree of condensation increased. At 180 °C, extensive degradation occurred in lignin derivatives. This research advances innovative techniques for lignin derivative separation, contributing to their utilization in higher-value applications.

Microalgal upgrading of the fermentative biohydrogen produced from Bacillus coagulans via non-pretreated plant biomass

BACKGROUND

Hydrogen is a promising source of alternative energy. Fermentative production is more feasible because of its high hydrogen generation rate, simple operating conditions, and utilization of various organic wastes as substrates. The most significant constraint for biohydrogen production is supplying it at a low cost with fewer impurities.

RESULTS

Leaf biomass of Calotropis procera was used as a feedstock for a dark fermentative production of hydrogen by Bacillus coagulans AH1 (MN923076). The optimum operation conditions for biohydrogen production were 5.0% substrate concentrationand pH 9.0, at 35 °C. In which the biohydrogen yield was 3.231 mmol H2/g dry biomass without any pretreatments of the biomass. A freshwater microalga Oscillatroia sp was used for upgrading of the produced biohydrogen. It sequestrated 97 and 99% % of CO2 from the gas mixture when it was cultivated in BG11 and BG11-N media, respectively After upgrading process, the residual microalgal cells exhibited 0.21mg/mL of biomass yield,high content of chlorophyll-a (4.8 µg/mL) and carotenoid (11.1 µg/mL). In addition to Oscillatroia sp residual biomass showed a lipid yield (7.5-8.7%) on the tested media.

CONCLUSION

Bacillus coagulans AH1 is a promising tool for biohydrogen production avoiding the drawbacks of biomass pretreatment. Oscillatroia sp is encouraged as a potent tool for upgrading and purification of biohydrogen. These findings led to the development of a multiproduct biorefinery with zero waste that is more economically sustainable.

Analytical Pyrolysis of Pinus radiata and Eucalyptus globulus: Effects of Microwave Pretreatment on Pyrolytic Vapours Composition

Pinus radiata (PR) and Eucalyptus globulus (EG) are the most planted species in Chile. This research aims to evaluate the pyrolysis behaviour of PR and EG from the Bío Bío region in Chile. Biomass samples were subjected to microwave pretreatment considering power (259, 462, 595, and 700 W) and time (1, 2, 3, and 5 min). The maximum temperature reached was 147.69 °C for PR and 130.71 °C for EG in the 700 W-5 min condition, which caused the rearrangement of the cellulose crystalline chains through vibration and an increase in the internal energy of the biomass and the decomposition of lignin due to reaching its glass transition temperature. Thermogravimetric analysis revealed an activation energy (Ea) reduction from 201.71 to 174.91 kJ·mol-1 in PR and from 174.80 to 158.51 kJ·mol-1 in EG, compared to the untreated condition (WOT) for the 700 W-5 min condition, which indicates that microwave pretreatment improves the activity of the components and the decomposition of structural compounds for subsequent pyrolysis. Functional groups were identified by Fourier transform infrared spectroscopy (FTIR). A decrease in oxygenated compounds such as acids (from 21.97 to 17.34% w·w-1 and from 27.72 to 24.13% w·w-1) and phenols (from 34.41 to 31.95% w·w-1 and from 21.73 to 20.24% w·w-1) in PR and EG, respectively, was observed in comparison to the WOT for the 700 W-5 min condition, after analytical pyrolysis. Such results demonstrate the positive influence of the pretreatment on the reduction in oxygenated compounds obtained from biomass pyrolysis.

A Systematic Review on Biomass Treatment Using Microwave-Assisted Pyrolysis under PRISMA Guidelines

Biomass as a renewable energy resource is a major topic on a global scale. Several types of biomass heat treatment methods have been introduced to obtain useful byproducts via pyrolysis. Microwaves are a practical replacement for conventional stoves and ovens to perform pyrolysis of biomass. Their rapid heating rate and user-friendliness make them a good choice for the pyrolysis process over conventional methods. The current study reviewed research articles that used microwaves for the pyrolysis process on different types of biomass. This study primarily provides comprehensive details about the pyrolysis process, especially microwave-assisted pyrolysis (MAP) and its feasibility for treating biomass. A systematic literature review, according to the PRISMA guidelines, was performed to find research articles on biomass treatment using MAP technology. We analyzed various research studies (n = 32), retrieved from different databases, that used MAP for pyrolysis on various types of biomass, and we achieved good results. The main goal of this study was to examine the usefulness of the MAP technique, comparing its effects on distinguished types of biomass. We found MAP's effective parameters, namely, temperature, concentration of microwave absorber, moisture percentage of starting material and flow rate, microwave power and residence time of the initial sweep gas that control the pyrolysis process, and effect quality of byproducts. The catalytic agent in MAP pyrolysis was found to be useful for treating biomass, and that it has great potential to increase (nearly double) the production yield. Although MAP could not be used for all types of materials due to some challenges, it produced good results compared to conventional heating (pyrolysis) methods. We concluded that MAP is an effective method for reducing pyrolysis reaction time and improving the quality of value-added products. Also, MAP eliminates the shredding requirement for biomass and improves heating quality. Therefore, it is a viable method for reducing pyrolysis processing costs and should be applied on a larger scale than lab scale for commercialization.

Effect of physical and thermal pretreatment of lignocellulosic biomass on biohydrogen production by thermochemical route: A critical review

Energy demands and immense environmental degradation have extorted for production of low-carbon and carbon-neutral fuels. Abundantly available lignocellulosic biomass is second-generation feedstock which has potential to produce biofuels. Among all biofuels, biohydrogen is carbon neutral and sustainable biofuel which can be produced by thermochemical conversion routes mainly gasification. However, there are still numerous unsolved challenges related to physicochemical properties of lignocellulosic biomass. To tackle these issues, physical, chemical and thermal pretreatment methods can be employed to improve these properties and further strengthen usability of biomass for biohydrogen production. Pelletization, torrefaction and hydrothermal carbonization pretreatment have shown significant results for treating biomass and biohydrogen enhancement. This study reviews physical and thermal pretreatment and its effect on biohydrogen yield. Framework of techno-economic analysis of processes is provided for examining feasibility of required pretreatments. This sustainable approach will help to reduce emissions and promote concept of bioenergy with carbon capture and storage.

Recent Advancements and Challenges in Lignin Valorization: Green Routes towards Sustainable Bioproducts

The aromatic hetero-polymer lignin is industrially processed in the paper/pulp and lignocellulose biorefinery, acting as a major energy source. It has been proven to be a natural resource for useful bioproducts; however, its depolymerization and conversion into high-value-added chemicals is the major challenge due to the complicated structure and heterogeneity. Conversely, the various pre-treatments techniques and valorization strategies offers a potential solution for developing a biomass-based biorefinery. Thus, the current review focus on the new isolation techniques for lignin, various pre-treatment approaches and biocatalytic methods for the synthesis of sustainable value-added products. Meanwhile, the challenges and prospective for the green synthesis of various biomolecules via utilizing the complicated hetero-polymer lignin are also discussed.

Residual Forest Biomass in Pinus Stands: Accumulation and Biogas Production Potential

Lignocellulosic biomass is an abundant resource that can be valorized for the production of bioenergy. However, studies aiming to quantify the amount of biogas production potential per km forest road are scarce in the literature. In this study, fresh pine needles, pine needle litter, pine branches, and pine bark were digested in batch reactors under mesophilic conditions after a grinding/milling pre-treatment. All samples were collected from a low-altitude Mediterranean Pinus forest (North Greece) adjacent to a category G forest road with a gentle slope. The methane yield of fresh pine needles was between 115 and 164 NmL g−1 volatile solids (VS), depending on the Pinus tree size. Pine needle litter produced a significantly lower methane yield (between 58 and 77 NmL g−1 VS), followed by pine bark (85 NmL g−1 VS) and pine branches (138 NmL g−1 VS). Considering the quantity of pine needle litter accumulated on adjacent forest roads (600 ± 200 g m−2), it was possible to calculate the biomethane production potential per km of forest road (up to 500 Nm3 km−1) if the biomass collected was disposed of at an anaerobic digestion facility. The results of the study demonstrate that residual forest biomass represents an additional resource for bioenergy production. Moreover, harvesting residual forest biomass can decrease the incidence of devastating summer forest fires and their disastrous consequences for the environment, the economy, and the local populations.

An Overview on Co-Pyrolysis of Biodegradable and Non-Biodegradable Wastes

Continuous urbanization and modernization have increased the burning of fossil fuels to meet energy needs across the globe, emanating environmental pollution and depleting fossil fuels. Therefore, a shift towards sustainable and renewable energy is necessary. Several techniques to exploit biomass to yield energy are trending, with pyrolysis one of them. Usually, a single feedstock is employed in pyrolysis for anoxygenic generation of biochar together with bio-oil at elevated temperatures (350–600 °C). Bio-oil produced through pyrolysis can be upgraded to crude oil after some modification. However, these modifications of bio-oil are one of the major drawbacks for its large-scale adoption, as upgradation increases the overall cost. Therefore, in recent years the scientific community has been researching co-pyrolysis technology that involves the pyrolysis of lignocellulosic biomass waste with non-biodegradable waste. Co-pyrolysis reduces the need for post-modification of bio-oil, unlike pyrolysis of a single feedstock. This review article discusses the recent advancements and technological challenges in waste biomass co-pyrolysis, the mechanism of co-pyrolysis, and factors that affect co-pyrolysis. The current study critically analyzes different recent research articles presented in databases such as PubMed, MDPI, ScienceDirect, Springer, etc. Hence, this review is one-of-a-kind in that it attempts to explain each and every aspect of the co-pyrolysis process and its current progress in the scientific field. Consequently, this review also compiles the remarkable achievements in co-pyrolysis and recommendations for the future.

Co-pyrolysis of biomass and plastic: Synergistic effects and estimation of elemental composition of pyrolysis oil by analytical pyrolysis-gas chromatography/mass spectrometry

This paper presents a study on the pyrolytic behavior of mixtures of lignocellulosic biomass with hydrocarbon plastics using analytical pyrolysis-GC/MS. Semi-quantitative analysis using chromatographic peak areas was used to investigate the composition of the pyrolysis oils and to highlight the occurrence of synergistic effects. A new method is also proposed to estimate the elemental composition of the pyrolysis oil based on the peak areas and brute formulas of the pyrolysis products. The results indicate that synergistic effects during co-pyrolysis favor secondary pyrolysis of holocellulose and polystyrene oligomers, and hinder radical chain-scission of polyethylene chains. H/C and O/C values of the pyrolysis oils were improved by the addition of plastic, indicating a decrease in the content of oxygenated pyrolysis products. The best performances were observed for the mixture containing 70% fir wood and 30% polyethylene, in which synergistic effects led to both an increase of H/C and a decrease of O/C.

The Thermochemical Conversion of Forestry Residues from Silver Fir (Abies alba Mill.) by Torrefaction and Pyrolysis

Forestry residue is a renewable energy biomass whose valorization has increased due to the interest in replacing exhaustible and environmentally unfriendly fossil resources. Needles, cones and bark from silver fir were thermally processed by separated and combined torrefaction (250 °C) and pyrolysis (550 °C). The torrefaction removed the humidity and extractives and degraded the hemicelluloses, significantly decreasing the oxygen content to ~11 wt% and increasing the carbon content to ~80 wt%, while enhancing the calorific value of the solids (~32 MJ/kg). The pyrolysis produced solid materials with high amounts of fixed carbon (~60–70 wt%) and high heating values, of ~29 MJ/kg. The combined torrefaction + pyrolysis increased the energy yield of the process and decreased the O/C and H/C atomic ratios to about 0.1 and 0.5, respectively, which is close to those of coals. It also led to condensable products with more homogeneously distributed compounds, regardless of the initial biomass type. More than 110 chemical compounds were confirmed in the condensable products, in amounts that depended on the type of starting material and on the thermal treatment. These included the following: terpenes, from extractives; furans, acids and linear ketones, from hemicelluloses; cyclic ketones and saccharides, from cellulose; and aromatic hydrocarbons and phenol derivatives, from lignin. Clear distinctions between the thermal procedures and the sample origins were evidenced by an exploratory data analysis (PCA), which suggested the presence of different types of lignin in the three starting materials.

Biotechnological advances in biomass pretreatment for bio-renewable production through nanotechnological intervention

Globally, the fossil fuel reserves are depleting rapidly and the escalating fuel prices as well as plethora of the pollutants released from the emission of burning fossil fuels cause global warming that massively disturb the ecological balance. Moreover, the unnecessary utilization of non-renewable energy sources is a genuine hazard to nature and economic stability, which demands an alternative renewable source of energy. The lignocellulosic biomass is the pillar of renewable sources of energy. Different conventional pretreatment methods of lignocellulosic feedstocks have employed for biofuel production. However, these pretreatments are associated with disadvantages such as high cost of chemical substances, high load of organic catalysts or mechanical equipment, time consuming, and production of toxic inhibitors causing the environmental pollution. Nanotechnology has shown the promised biorefinery results by overcoming the disadvantages associated with the conventional pretreatments. Recyclability of nanomaterials offers cost effective and economically viable biorefineries processes. Lignolytic and saccharolytic enzymes have immobilized onto/into the nanomaterials for the higher biocatalyst loading due to their inherent properties of high surface area to volume ratios. Nanobiocatalyst enhance the hydrolyzing process of pretreated biomass by their high penetration into the cell wall to disintegrate the complex carbohydrates for the release of high amounts of sugars towards biofuel and various by-products production. Different nanotechnological routes provide cost-effective bioenergy production from the rich repertoires of the forest and agricultural-based lignocellulosic biomass. In this article, a critical survey of diverse biomass pretreatment methods and the nanotechnological interventions for opening up the biomass structure has been carried out.

Bibliographic Coupling Links: Alternative Approaches to Carrying Out Systematic Reviews about Renewable and Sustainable Energy

New technologies, specifically the internet, have over the last two decades increased the number of publications in the most diverse fields of science. Subjects related to renewable and sustainable energy are no exception. These frameworks have allowed the main insights produced by the scientific community through literature surveys to be highlighted. Nonetheless, considering the vast quantity of studies, systematic approaches have been proposed by the researchers to better organize and perform the literature review. Considering the subjectivity of some of these methodologies, the main objectives of this research are to conduct a systematic review about renewable and sustainable energy through more objective techniques, based on bibliometric analysis, to provide an alternative or to complement those already available within the literature. For this purpose, a “Biblio4Review” approach was proposed in order to perform systematic reviews about renewable and sustainable energy that may spread into other scientific fields. This methodology is based on bibliographic coupling links from the bibliometric analysis to identify the most relevant studies for the literature review. The results obtained highlight that with this approach it was possible to identify the studies with greater centrality in terms of references shared. In this way, they are among the most relevant documents for these topics. Specifically for the topic considered (renewable and sustainable energy) the main insights were referred to. In any case, the findings obtained show that there is a field for more interdisciplinary approaches.

Microwave Assisted Pretreatment of Szarvasi (Agropyron elongatum) Biomass to Enhance Enzymatic Saccharification and Direct Glucose Production

Biomass from perennial plants can be considered a carbon-neutral renewable resource. The tall wheatgrass hybrid Szarvasi-1 (Agropyron elongatum, hereafter referred to as "Szarvasi") belongs to the perennial Poaceae representing a species, which can grow on marginal soils and produce large amounts of biomass. Several conventional and advanced pretreatment methods have been developed to enhance the saccharification efficiency of plant biomass. Advanced pretreatment methods, such as microwave-assisted pretreatment methods are faster and use less energy compared to conventional pretreatment methods. In this study, we investigated the potential of Szarvasi biomass as a biorefinery feedstock. For this purpose, the lignocellulosic structure of Szarvasi biomass was investigated in detail. In addition, microwave-assisted pretreatments were applied to Szarvasi biomass using different reagents including weak acids and alkali. The produced pulp, hydrolysates, and extracted lignin were quantitatively characterized. In particular, the alkali pretreatment significantly enhanced the saccharification efficiency of the pulp 16-fold compared to untreated biomass of Szarvasi. The acid pretreatment directly converted 25% of the cellulose into glucose without the need of enzymatic digestion. In addition, based on lignin compositional and lignin linkage analysis a lignin chemical model structure present in Szarvasi biomass could be established.

Valorization of Vine Prunings by Slow Pyrolysis in a Fixed-Bed Reactor

The paper aimed at studying the slow pyrolysis of vine pruning waste in a fixed bed reactor and characterizing the pyrolysis products. Pyrolysis experiments were conducted for 60 min, using CO2 as a carrier gas and oxidizing agent. The distribution of biochar and bio-oil was dependent on variations in heat flux (4244–5777 W/m2), CO2 superficial velocity (0.004–0.008 m/s), and mean size of vegetal material (0.007–0.011 m). Relationships among these factors and process performances in terms of yields of biochar (0.286–0.328) and bio-oil (0.260–0.350), expressed as ratio between the final mass of pyrolysis product and initial mass of vegetal material, and final value of fixed bed temperature (401.1–486.5 °C) were established using a 23 factorial design. Proximate and ultimate analyses, FT-IR and SEM analyses, measurements of bulk density (0.112 ± 0.001 g/cm3), electrical conductivity (0.55 ± 0.03 dS/m), pH (10.35 ± 0.06), and water holding capacity (58.99 ± 14.51%) were performed for biochar. Water content (33.2 ± 1.27%), density (1.027 ± 0.014 g/cm3), pH (3.34 ± 0.02), refractive index (1.3553 ± 0.0027), and iodine value (87.98 ± 4.38 g I2/100 g bio-oil) were measured for bio-oil. Moreover, chemical composition of bio-oil was evaluated using GC-MS analysis, with 27 organic compounds being identified.

Acid-based lignocellulosic biomass biorefinery for bioenergy production: Advantages, application constraints, and perspectives

The production of chemicals and fuels from renewable biomass with the primary aim of reducing carbon footprints has recently become one of the central points of interest. The use of lignocellulosic biomass for energy production is believed to meet the main criteria of maximizing the available global energy source and minimizing pollutant emissions. However, before usage in bioenergy production, lignocellulosic biomass needs to undergo several processes, among which biomass pretreatment plays an important role in the yield, productivity, and quality of the products. Acid-based pretreatment, one of the existing methods applied for lignocellulosic biomass pretreatment, has several advantages, such as short operating time and high efficiency. A thorough analysis of the characteristics of acid-based biomass pretreatment is presented in this review. The environmental concerns and future challenges involved in using acid pretreatment methods are discussed in detail to achieve clean and sustainable bioenergy production. The application of acid to biomass pretreatment is considered an effective process for biorefineries that aim to optimize the production of desired products while minimizing the by-products.

Insight into the recent advances of microwave pretreatment technologies for the conversion of lignocellulosic biomass into sustainable biofuel

The utilization of renewable lignocellulosic biomasses for bioenergy synthesis is believed to facilitate competitive commercialization and realize affordable clean energy sources in the future. Among the pathways for biomass pretreatment methods that enhance the efficiency of the whole biofuel production process, the combined microwave irradiation and physicochemical approach is found to provide many economic and environmental benefits. Several studies on microwave-based pretreatment technologies for biomass conversion have been conducted in recent years. Although some reviews are available, most did not comprehensively analyze microwave-physicochemical pretreatment techniques for biomass conversion. The study of these techniques is crucial for sustainable biofuel generation. Therefore, the biomass pretreatment process that combines the physicochemical method with microwave-assisted irradiation is reviewed in this paper. The effects of this pretreatment process on lignocellulosic structure and the ratio of achieved components were also discussed in detail. Pretreatment processes for biomass conversion were substantially affected by temperature, irradiation time, initial feedstock components, catalyst loading, and microwave power. Consequently, neoteric technologies utilizing high efficiency-based green and sustainable solutions should receive further focus. In addition, methodologies for quantifying and evaluating effects and relevant trade-offs should be develop to facilitate the take-off of the biofuel industry with clean and sustainable goals.

Non-Catalytic Dissolution of Biochar Obtained by Hydrothermal Carbonization of Sawdust in Hydrogen Donor Solvent

The production of fuel hydrocarbons from CO2-neutral raw materials is a promising task at present. The thermal dissolution of biochar obtained by the method of hydrothermal carbonization of sawdust was studied. The dissolution of biochar in tetralin (hydrogen donor solvent) was studied at different temperatures (350–450 °C) and with two types of dilution of the mixture with tetralin: 1/3 and 1/4. The process proceeded without a catalyst. It was found that the samples subjected to thermal dissolution at temperatures of 425–450 °C had the highest conversion and yield of liquid products. The reaction temperature also had a significant effect on the composition of liquid products. It was found that an increase in the reaction temperature led to a significant increase in benzenes, both in the direct and in the hexane fraction. A benzene yield of more than 50% was observed for both fractions at a temperature of 450 °C. It was also suggested that the possible positive effect of abietates on the homogenization of the reaction mixture contributed to high conversion in the process. The biochar/tetralin ratio effects the yield and composition of the liquid products as well. An increase in the tetralin concentration in the mixture during thermal dissolution led to an increase in the conversion and yield of hydrocarbon fractions for fuel purposes. This is undoubtedly due to the large amount of elemental hydrogen involved in the hydrogenation of the reaction mixture.

Greener Pretreatment Approaches for the Valorisation of Natural Fibre Biomass into Bioproducts

The utilization of lignocellulosic biomass in various applications has a promising potential as advanced technology progresses due to its renowned advantages as cheap and abundant feedstock. The main drawback in the utilization of this type of biomass is the essential requirement for the pretreatment process. The most common pretreatment process applied is chemical pretreatment. However, it is a non-eco-friendly process. Therefore, this review aims to bring into light several greener pretreatment processes as an alternative approach for the current chemical pretreatment. The main processes for each physical and biological pretreatment process are reviewed and highlighted. Additionally, recent advances in the effect of different non-chemical pretreatment approaches for the natural fibres are also critically discussed with a focus on bioproducts conversion.

Improving the Conversion of Biomass in Catalytic Pyrolysis via Intensification of Biomass—Catalyst Contact by Co-Pressing

Biomass pyrolysis is a promising technology for fuel and chemical production from an abundant renewable source. It takes place usually in two stages; non-catalytic pyrolysis with further catalytic upgrading of the formed pyrolysis oil. The direct catalytic pyrolysis of biomass reduces the pyrolysis temperature, increase the yield to target products and improves their quality. However, in such one-stage process the contact between biomass and solid catalyst particles is poor leading to an excessively high degree of pure thermal pyrolysis reactions. The aim of this study was to enhance the catalyst-biomass contact via co-pressing of biomass and catalyst particles as a pre-treatment method. Catalytic pyrolysis of biomass components with HY and USY zeolites was studied using thermogravimetric analysis (TGA), as well as experiments in a pyrolysis reactor. The liquid and coke yields were characterized using gas chromatography, and TGA respectively. The TGA results showed that the degradation of the co-pressed cellulose occurred at lower temperatures compared to the pure thermal degradation, as well as catalytic degradation of non-pretreated cellulose. All biomass components produced better results using the co-pressing method, where the liquid yields increased while coke/char yields decreased. Bio-oil from catalytic pyrolysis of cellulose with HY catalyst mainly produced heavier fractions, while in the presence of USY catalyst medium fraction was mainly produced within the gasoline range. For hemicellulose catalytic pyrolysis, the catalysts had similar effects in enhancing the lighter fraction, but specifically, HY showed higher selectivity to middle fraction while USY has produced higher percentage of lighter fraction. Using with both catalysts, co-pressing had the best effect of eliminating the heavier fraction and improving the gasoline range fraction. Spent catalyst from co-pressed sample had lower concentrations of coke/char components due to the shorter residence times of volatiles, which suppresses the occurrence of secondary reactions leading to coke/char formations.

Microbial lipid biosynthesis from lignocellulosic biomass pyrolysis products

Lipids are a biorefinery platform to prepare fuel, food and health products. They are traditionally obtained from plants, but those of microbial origin allow for a better use of land and C resources, among other benefits. Several (thermo)chemical and biochemical strategies are used for the conversion of C contained in lignocellulosic biomass into lipids. In particular, pyrolysis can process virtually any biomass and is easy to scale up. Products offer cost-effective, renewable C in the form of readily fermentable molecules and other upgradable intermediates. Although the production of microbial lipids has been studied for 30 years, their incorporation into biorefineries was only described a few years ago. As pyrolysis becomes a profitable technology to depolymerize lignocellulosic biomass into assimilable C, the number of investigations on it raises significantly. This article describes the challenges and opportunities resulting from the combination of lignocellulosic biomass pyrolysis and lipid biosynthesis with oleaginous microorganisms. First, this work presents the basics of the individual processes, and then it shows state-of-the-art processes for the preparation of microbial lipids from biomass pyrolysis products. Advanced knowledge on separation techniques, structure analysis, and fermentability is detailed for each biomass pyrolysis fraction. Finally, the microbial fatty acid platform comprising biofuel, human food and animal feed products, and others, is presented. Literature shows that the microbial lipid production from anhydrosugars, like levoglucosan, and short-chain organic acids, like acetic acid, is straightforward. Indeed, processes achieving nearly theoretical yields form the latter have been described. Some authors have shown that lipid biosynthesis from different lignin sources is biochemically feasible. However, it still imposes major challenges regarding strain performance. No report on the fermentation of pyrolytic lignin is yet available. Research on the microbial uptake of pyrolytic humins remains vacant. Microorganisms that make use of methane show promising results at the proof-of-concept level. Overall, despite some issues need to be tackled, it is now possible to conceive new versatile biorefinery models by combining lignocellulosic biomass pyrolysis products and robust oleaginous microbial cell factories.

Physicochemical Characterisation and the Prospects of Biofuel Production from Rubberwood Sawdust and Sewage Sludge

This study aims to evaluate the physicochemical properties of rubberwood sawdust (RWS) and sewage sludge (SS) for producing biofuel or liquid products via pyrolysis and co-pyrolysis. The chemical and thermal properties of both samples were observed to have superior bioenergy production capabilities. RWS and SS had significantly different physicochemical properties, such as particle-size distribution, bulk density, ultimate and proximate analysis, lignocellulose composition, thermal-degradation behaviour, and major and minor elements. The composition of extractives was found to only marginally affect the end product. Carbon and hydrogen content, the two main elements for biofuel enhancement, were found to correlate with the organic components of both RWS (48.49, 7.15 wt.%) and SS (32.29, 4.06 wt.%). SS had a higher elemental composition of iron, calcium, and potassium than RWS. Both samples had a higher heating value of 13.98 to 21.01 MJ/kg and a lower heating value of 11.65 to 17.66 MJ/kg, a lesser energy potential than that of fossil fuels. The findings from these blends are relatively moderate due to the related lignocellulosic potential composition. The novel contribution of this research was to optimize the use of local waste materials as a new raw material for biofuel production that could serve as a sustainable fuel source.

Impact of culture condition modulation on the high-yield, high-specificity and cost-effective production of terpenoids from microbial sources: A review

Recent years have seen a remarkable increase in the non-natural production of terpenoids from microbial route. This is due to the advancements in synthetic biology tools and techniques, which have overcome the challenges associated with the non-native production of terpenoids from microbial hosts. Although, microbes in their native form have ability to grow in wide range of physicochemical parameters such as, pH, temperature, agitation, aeration etc; however, after genetic modifications, culture conditions need to be optimized in order to achieve improved titers of desired terpenoids from engineered microbes. The physicochemical parameters together with medium supplements, such as, inducer, carbon and nitrogen source, and cofactor supply not only play an important role in high-yield production of target terpenoids from engineered host, but also reduce the accumulation of undesired metabolites in fermentation medium, thus facilitate product recovery. Further, for the economic production of terpenoids, the biomass derived sugars can be utilized together with the optimized culture conditions. In the present mini-review, we have highlighted the impact of culture conditions modulation on the high-yield and high-specificity production of terpenoids from engineered microbes. Lastly, utilization of economic feedstock has also been discussed for the cost-effective and sustainable production of terpenoids.

Effects of Pyrolysis Bio-Oils on Fuel Atomisation—A Review

Bio-oils produced by biomass pyrolysis are substantially different from those produced by petroleum-based fuels and biodiesel. However, they could serve as valuable alternatives to fossil fuels to achieve carbon neutral future. The literature review indicates that the current use of bio-oils in gas turbines and compression-ignition (diesel) engines is limited due to problems associated with atomisation and combustion. The review also identifies the progress made in pyrolysis bio-oil spray combustion via standardisation of fuel properties, optimising atomisation and combustion, and understanding long-term reliability of engines. The key strategies that need to be adapted to efficiently atomise and combust bio-oils include, efficient atomisation techniques such as twin fluid atomisation, pressure atomisation and more advanced and novel effervescent atomisation, fuel and air preheating, flame stabilization using swrilers, and filtering the solid content from the pyrolysis oils. Once these strategies are implemented, bio-oils can enhance combustion efficiency and reduce greenhouse gas (GHG) emission. Overall, this study clearly indicates that pyrolysis bio-oils have the ability to substitute fossil fuels, but fuel injection problems need to be tackled in order to insure proper atomisation and combustion of the fuel.

Advanced process integration for supercritical production of biodiesel: Residual waste heat recovery via organic Rankine cycle (ORC)

Biodiesel production using supercritical methanolysis has received immense interest over the last few years. It has the ability to convert high acid value feedstock into biodiesel using a single-pot reaction. However, the energy intensive process is the main disadvantage of supercritical biodiesel process. Herein, a conceptual design for the integration of supercritical biodiesel process with organic Rankine cycle (ORC) is presented to recover residual hot streams and to generate electric power. This article provides energy and techno-economic comparative study for three developed scenarios as follows: original process with no energy integration (Scenario 1), energy integrated process (Scenario 2) and advanced energy integrated process with ORC (Scenario 3). The developed integrated biodiesel process with ORC resulted in electric power generation that has not only satisfied the process electric requirement but also provided excess power of 257 kW for 8,000 tonnes/annum biodiesel plant. The techno-economic comparative analysis resulted in favouring the third scenario with 36% increase in the process profitability than the second scenario. Sensitivity analysis has shown that biodiesel price variation has significant effect on the process profitability. In summary, integrating supercritical biodiesel production process with ORC appears to be a promising approach for enhancing the process techno-economic profitability and viability.

Glycerol Assisted Pretreatment of Lignocellulose Wheat Straw Materials as a Promising Approach for Fabrication of Sustainable Fibrous Filler for Biocomposites

Glycerol pretreatment is a promising method for the environmentally-friendly transformation of lignocellulosic materials into sustainable cellulose-rich raw materials (i.e., biopolymer) to fabricate biocomposites. Here, a comparison of aqueous acidified glycerol (AAG) pretreatment of wheat straw (WS) with alkaline, hot water, and dilute acid pretreatments on the thermal and mechanical characteristics of their fabricated composite board is presented. A comparison of total energy expenditure during WS pretreatment with AAG and other solutions was estimated and a comparative influence of AAG processing on lignocellulosic constituents and thermal stability of WS fiber was studied. Results imply that AAG pretreatment was superior in generating cellulose-rich fiber (CRF) as compared to other pretreatments and enhanced the cellulose contents by 90% compared to raw WS fiber. Flexural strength of acidic (40.50 MPa) and hot water treated WS composite (38.71 MPa) was higher compared to the value of 33.57 MPa for untreated composite, but AAG-treated composites exhibited lower values of flexural strength (22.22 MPa) compared to untreated composite samples. Conversely, AAG pretreatment consumed about 56% lesser energy for each kg of WS processed as compared to other pretreatments. These findings recognize that glycerol pretreatment could be a clean and new pretreatment strategy to convert agricultural waste into high-quality CRF as a sustainable raw material source for engineered biocomposite panels.

Experimental and Numerical Analysis of a Low Environmental Impact Pyro-Gasification System for the Energetic Valorization of Waste through a Biomass Steam Power Plant

This paper addresses the study of a pyro-gasification plant designed, built, and operated to recover inert metals from different types of solid waste. Experimental tests were carried out using pulper as the solid waste. However, while a reliable composition analysis of the produced syngas was carried out, a precise composition evaluation of the pulper used during the experimental activities was not performed and the related data were characterized by unacceptable uncertainty. Therefore, with the aim of reliably characterizing the plant operation, a thermochemical model of the gasification process was setup to simulate the equilibrium operation of the plant and a vector optimization methodology was used to calibrate the numerical model. Then, a decision-making problem was solved to identify the most suitable optimal solution between those belonging to the Pareto optimal front, thus obtaining reliable composition data for the adopted pulper waste. In particular, four different identification criteria were applied for the selection of small subset of solutions over the 3138 dominant solutions found. Among them, the solution (i.e., set of calibration parameters) that minimizes the experimental-numerical difference between the lower heating value of the produced syngas seemed to provide the most reliable approximation of the real plant operation. Finally, a possible plant configuration is proposed for the energetic valorization of the pulper waste and its overall conversion process efficiency is estimated.

Microwave-Assisted Pyrolysis of Biomass Waste: A Mini Review

The utilization of biomass waste as a raw material for renewable energy is a global concern. Pyrolysis is one of the thermal treatments for biomass wastes that results in the production of liquid, solid and gaseous products. Unfortunately, the complex structure of the biomass materials matrix needs elevated heating to convert these materials into useful products. Microwave heating is a promising alternative to conventional heating approaches. Recently, it has been widely used in pyrolysis due to easy operation and its high heating rate. This review tries to identify the microwave-assisted pyrolysis treatment process fundamentals and discusses various key operating parameters which have an effect on product yield. It was found that several operating parameters govern this process such as microwave power and the degree of temperature, microwave absorber addition and its concentration, initial moisture content, initial sweep gas flow rate/residence time. Moreover, this study highlighted the most attractive products of the microwave pyrolysis process. These products include synthesis gas, bio-char, and bio-oil. The benefits and challenges of microwave heating are discussed.