Simultaneous electrochemical detection of dopamine and ascorbic acid using an iron oxide/reduced graphene oxide modified glassy carbon electrode

1-D Carbon Nano-Coils Derived from Almond Skin: Exhibiting Density of State, Diffusivity, Electron Transfer Rate, and Dopamine Redox Modulation Properties Akin to Graphene Oxide

The quest to develop graphene-like biomass-carbon for advanced biomolecule redox modulation and sensing remains a challenge. The primary obstacle is the limited ability of biomass to undergo extensive graphitization during pyrolysis resulting in the formation of amorphous carbon materials with a small carbon-double-bond-carbon domain size (Lsp2), density of state (LDOS), ion diffusivity (D), and electron transfer rate constant (Ks). Herein, using almond skin (AS) the morphology of biomass is demonstrated as the key to overcoming these limitations. AS consists of 1D syringyl/guaiacyl lignin nano-coils which under H2/H2 annealing transform into pyrolytic 1D carbon nano-coils (r-gC). Spectroscopy and microscopy analyses reveal that the sheet layering structure, crystallinity, LDOS, and Lsp2 of r-gC mimic those of graphene oxide (GO). Moreover, its unique 1D morphology and profound microstructure facilitate faster charge transfer and ion diffusion than GO's planar structure, leading to better redox modulation and sensing of the neurotransmitter dopamine (DA) in physiological fluids. r-gC's DA detection limit of 3.62 nM is below the lower threshold found in humans and on par with the state-of-the-art. r-gC is also DA-selective over 14 biochemicals. This study reveals that biomasses with well-defined and compact lignin structures are best suited for developing highly electroactive graphene-like biomass carbon.

Voltammetric analysis of pholcodine on graphene-modified GNPs/PTs with green assessment

Pholcodine, an anti-tussive medication widely used as an over-the-counter, OTC drug, has recently faced restrictions in several countries. This paper presents a sensitive electrochemical approach for pholcodine detection. The electrochemical method involved fabricating a graphene nanoplatelets electrode, incorporating polythiophene nanospheres polymer to promote electron transfer and increase the activated surface area. Characterization of the fabricated electrode was performed using transmission electron microscopy, ATR-Fourier-transform infrared spectroscopy, X-ray crystallography, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy. The electrochemical behavior of pholcodine with the fabricated electrode was investigated using cyclic voltammetry, chronoamperometry, square wave voltammetry (SWV), and differential pulse voltammetry (DPV). The developed electrode led to a linear response for pholcodine ranging from 10 to 45 mg/L with detection limits of 1.41 and 1.51 mg/mL for SWV and DPV, respectively and quantification limits of 4.27 and 4.57 mg/L for SWV and DPV, respectively. The proposed method has accurately recovered pholcodine in spiked serum samples with a recovery percentage ranging from 1.2 to 2.9%. The optimized method is found to be accurate, precise, and robust by applying validation parameters provided by International Council for Harmonization. Two green metrics were computed to assess the method's greenness, the findings showed that the developed method is environmentally friendly with minimum sample preparation steps.

Nanomaterials-based biosensor and their applications: A review

A sensor can be called ideal or perfect if it is enriched with certain characteristics viz., superior detections range, high sensitivity, selectivity, resolution, reproducibility, repeatability, and response time with good flow. Recently, biosensors made of nanoparticles (NPs) have gained very high popularity due to their excellent applications in nearly all the fields of science and technology. The use of NPs in the biosensor is usually done to fill the gap between the converter and the bioreceptor, which is at the nanoscale. Simultaneously the uses of NPs and electrochemical techniques have led to the emergence of biosensors with high sensitivity and decomposition power. This review summarizes the development of biosensors made of NPssuch as noble metal NPs and metal oxide NPs, nanowires (NWs), nanorods (NRs), carbon nanotubes (CNTs), quantum dots (QDs), and dendrimers and their recent advancement in biosensing technology with the expansion of nanotechnology.

Spongin as a Unique 3D Template for the Development of Functional Iron-Based Composites Using Biomimetic Approach In Vitro

Marine sponges of the subclass Keratosa originated on our planet about 900 million years ago and represent evolutionarily ancient and hierarchically structured biological materials. One of them, proteinaceous spongin, is responsible for the formation of 3D structured fibrous skeletons and remains enigmatic with complex chemistry. The objective of this study was to investigate the interaction of spongin with iron ions in a marine environment due to biocorrosion, leading to the occurrence of lepidocrocite. For this purpose, a biomimetic approach for the development of a new lepidocrocite-containing 3D spongin scaffold under laboratory conditions at 24 °C using artificial seawater and iron is described for the first time. This method helps to obtain a new composite as "Iron-Spongin", which was characterized by infrared spectroscopy and thermogravimetry. Furthermore, sophisticated techniques such as X-ray fluorescence, microscope technique, and X-Ray diffraction were used to determine the structure. This research proposed a corresponding mechanism of lepidocrocite formation, which may be connected with the spongin amino acids functional groups. Moreover, the potential application of the biocomposite as an electrochemical dopamine sensor is proposed. The conducted research not only shows the mechanism or sensor properties of "Iron-spongin" but also opens the door to other applications of these multifunctional materials.

Laser-induced graphene-based electrochemical biosensors for environmental applications: a perspective

Biosensors are miniaturized devices that provide the advantage of in situ and point-of-care monitoring of analytes of interest. Electrochemical biosensors use the mechanism of oxidation-reduction reactions and measurement of corresponding electron transfer as changes in current, voltage, or other parameters using different electrochemical techniques. The use of electrochemically active materials is critical for the effective functioning of electrochemical biosensors. Laser-induced graphene (LIG) has garnered increasing interest in biosensor development and improvement due to its high electrical conductivity, specific surface area, and simple and scalable fabrication process. The effort of this perspective is to understand the existing classes of analytes and the mechanisms of their detection using LIG-based biosensors. The manuscript has highlighted the potential use of LIG, its modifications, and its use with various receptors for sensing various environmental pollutants. Although the conventional graphene-based sensors effectively detect trace levels for many analytes in different applications, the chemical and energy-intensive fabrication and time-consuming processes make it imperative to explore a low-cost and scalable option such as LIG for biosensors production. The focus of these potential biosensors has been kept on detection analytes of environmental significance such as heavy metals ions, organic and inorganic compounds, fertilizers, pesticides, pathogens, and antibiotics. The use of LIG directly as an electrode, its modifications with nanomaterials and polymers, and its combination with bioreceptors such as aptamers and polymers has been summarized. The strengths, weaknesses, opportunities, and threats analysis has also been done to understand the viability of incorporating LIG-based electrochemical biosensors for environmental applications.

Chemical Sensor Nanotechnology in Pharmaceutical Drug Research

The increase in demand for pharmaceutical treatments due to pandemic-related illnesses has created a need for improved quality control in drug manufacturing. Understanding the physical, biological, and chemical properties of APIs is an important area of health-related research. As such, research into enhanced chemical sensing and analysis of pharmaceutical ingredients (APIs) for drug development, delivery and monitoring has become immensely popular in the nanotechnology space. Nanomaterial-based chemical sensors have been used to detect and analyze APIs related to the treatment of various illnesses pre and post administration. Furthermore, electrical and optical techniques are often coupled with nano-chemical sensors to produce data for various applications which relate to the efficiencies of the APIs. In this review, we focus on the latest nanotechnology applied to probing the chemical and biochemical properties of pharmaceutical drugs, placing specific interest on several types of nanomaterial-based chemical sensors, their characteristics, detection methods, and applications. This study offers insight into the progress in drug development and monitoring research for designing improved quality control methods for pharmaceutical and health-related research.

Construction of Electrochemical and Photoelectrochemical Sensing Platform Based on Porphyrinic Metal-Organic Frameworks for Determination of Ascorbic Acid

Highly sensitive and specific detection of biomolecular markers is of great importance to the diagnosis and treatment of related diseases. Herein, Cu-TCPP@MOFs thin films were synthesized with tetrakis(4-carboxyphenyl) porphyrin (H₂TCPP) as organic ligands and copper ions as metal nodes. The as-synthesized Cu-TCPP@MOFs thin films as electrode modifiers were used to modify the pre-treated glassy carbon electrode (GCE) and the electrochemical performances of Cu-TCPP@MOFs/GCE were evaluated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Furthermore, as the working electrode, the constructed Cu-TCPP@MOFs/GCE was used for the investigation of ascorbic acid (AA) due to its outstanding electrocatalytic activities towards AA by several electrochemical methods, including cyclic voltammetry (CV), differential pulse voltammetry (DPV), and chronoamperometry (CA). The well-linear relationship was established based on different AA concentration ranges and the ideal detection limits (LOD) were obtained in the above-mentioned electrochemical methods, respectively. Furthermore, a Cu-TCPP MOFs@GCE sensing platform was used as a photoelectrochemical (PEC) sensor to quantitatively detect AA based on the strong absorption properties of Cu-TCPP ingredients in Cu-TCPP MOFs in a visible light band of 400~700 nm. PEC sensing platform based on Cu-TCPP@MOFs exhibited a more extensive linear concentration range, more ideal detection limit, and better sensitivity relative than the other electrochemical methods for AA. The well linear regression equations were established between the peak current intensity and AA concentrations in different electrochemical technologies, including CV, DPV, and CA, and PEC technology. AA concentration ranges applicable to various electrochemical equations were as follows: 0.45~2.10 mM of CV, 0.75~2.025 mM of DPV, 0.3~2.4 mM of CA, 7.5~480 μM of PEC, and the corresponding detection limits for AA were 1.08 μM (S/N = 3), 0.14 μM (S/N = 3), 0.049 μM (S/N = 3), and 0.084 nA/μM. Moreover, the proposed Cu-TCPP MOFs@GCE electrochemical and photoelectrochemical sensing platform was applied to determine the AA concentration of a real human serum sample; the results reveal that Cu-TCPP MOFs@GCE sensing platform could accurately determine the concentration of AA of the human serum under other potential interferences contained in the human serum samples.

Graphene nanosheet-sandwiched platinum nanoparticles deposited on a graphite pencil electrode as an ultrasensitive sensor for dopamine

An ultra-sensitive sensor of dopamine is introduced. The sensor is constructed by encapsulating platinum nanoparticles (PtNPs) between reduced graphene oxide (GR) nanosheets. The sandwiched PtNPs between GR layers acted as a spacer to prevent aggregation and provided a fine connection between the GR nanosheets to provide fast charge transfer. This specific orientation of the GR nanosheets and PtNPs on the graphite pencil electrode (GPE) substantially improved the electrocatalytic activity of the sensor. The synthesized graphene oxide and the fabricated sensor were comprehensively characterized by Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, field emission-scanning electron microscopy (FE-SEM), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and square wave voltammetry (SWV). The value of the charge transfer coefficient (α), apparent heterogeneous electron transfer rate constant (k_s), and electroactive surface area for dopamine were found to be about 0.57, 8.99 s⁻¹, and 0.81 cm², respectively. The developed sensor is highly sensitive towards dopamine, and the detection limit is 9.0 nM. The sensor response is linear for dopamine concentration from 0.06 to 20 μM (R² = 0.9991). The behavior of the sensor for dopamine in the presence of a high concentration of l(+) Ascorbic acid and other potential interferents was satisfactory. High recovery percentage between 90% and 105% in the human urine sample, good reproducibility, and facile fabrication of the electrode make it a good candidate for dopamine sensing.

An efficient, highly sensitive, and selective electrochemical sensor using PtNPs sandwiched graphene layered modified graphite pencil electrode.

Electrochemical Study of Dimensional Specific Carbon Nanomaterials Modified Glassy Carbon Electrode for Highly Sensitive Label-free Detection of Immunoglobulin A

Background:

Immunoglobulin A (IgA) accounts for 15% of total protein production per day and plays a crucial role in the first-line immune defence. Recently, IgA has been established as a vital clinical biomarker for nephropathy, allergic asthma, celiac disease (CD), pneumonia, and asthma as well as some neurological disorders. In this work, we have studied several carbon nanomaterials (CNMs) having different dimensions (D): carbon nano-onions (CNOs) - 0D, single-walled carbon nanotubes (SWCNTs) - 1D, and graphene nanoplatelets (GNPs) - 2D, on glassy carbon electrode (GCE) to identify which CNMs (CNOs/SWCNTs/GNPs) work best to fabricate IgA based electrochemical immunosensor.

Methods:

Different CNMs (CNOs, SWCNTs, GNPs) were tested for high electric current on GCE using square wave voltammetry (SWV), and among them, GNPs modified GCE platform (GNPs/GCE) showcased the highest electric current. Therefore, GNPs/GCE was utilized for the development of highly sensitive label-free electrochemical immunosensor for the detection of Immunoglobulin A using SWV.

Results:

Despite the simple fabrication strategies employed, the fabricated sensor demonstrated a low limit of detection of 50 fg mL-1 with an extensive linear range of detection from 50 fg mL-1 to 0.1 μg mL-1.

Conclusion:

Fabricated immunosensor represented high stability, repeatability, specificity and resistance to most common interferences as well as great potential to analyse the real sample.

Green Method Synthesised Graphene-Silver Electrochemical Nanobiosensors for Ethambutol and Pyrazinamide

A novel nanobiosensor was constructed with graphene oxide (GO) sheets coupled to pear extract-based green-synthesised silver nanoparticles (Ag-NPs) to which cytochrome P450-2D6 (CYP2D6) enzyme was attached. The biosensor was applied in the electrochemical detection of the tuberculosis (TB) treatment drugs, ethambutol (EMB) and pyrazinamide (PZA). The surface morphology of the green-synthesised nanocomposites was studied by performing High-Resolution Transmission Electron Microscopy (HR-TEM) and High-Resolution Scanning Electron Microscopy (HR-SEM). Fourier Transform Infrared Spectroscopy (FTIR) and Raman Spectroscopy were used for structural analysis, while Ultraviolet Visible (UV-Vis) Spectroscopy was used in the optical characterisation of the nanocomposite material. Electrochemical studies on glassy carbon electrode (GCE), which were done by Cyclic Voltammetry (CV), showed that the GO|Ag-NPs||GCE electrode was highly conductive, and thereby indicating its suitability as a platform for nanobiosensor development. The non-toxic and low-cost green GO|Ag-NPs|CYP2D6||GCE nanobiosensor was used to determine EMB and PZA. The very low limit of detection (LOD) values of the biosensor for EMB (0.2962 × 10−2 nM, S/N = 3) and PZA (0.897 × 10−2 nM, S/N = 3) demonstrate that the green nanobiosensor is more sensitive than other biosensors reported for EMB and PZA.

Solar Exfoliated Graphene Oxide: A Platform for Electrochemical Sensing of Epinephrine

Introduction:

In this study, solar exfoliated graphite oxide modified glassy carbon electrode was used for the anodic oxidation of epinephrine in a phosphate buffer medium at pH7. The modified electrode showed fast response and sensitivity towards Epinephrine Molecule (EP). The electrode was characterized electrochemically through Cyclic Voltammetry (CV) and Differential Pulse Voltammetry (DPV). Area of the electrode enhanced three times during modification and studies reveal that the oxidation process of EP occurs by an adsorption controlled process involving two electrons. The results showed a detection limit of 0.50 ± 0.01μM with a linear range up to 100 μM. The rate constant calculated for the electron transfer reaction is 1.35 s-1. The electrode was effective for simultaneous detection of EP in the presence of Ascorbic Acid (AA) and Uric Acid (UA) with well-resolved signals. The sensitivity, selectivity and stability of the sensor were also confirmed.

Methods:

Glassy carbon electrode modified by reduced graphene oxide was used for the detection and quantification of epinephrine using cyclic voltammetry and differential pulse voltammetry.

Results:

The results showed an enhancement in the electrocatalytic oxidation of epinephrine due to the increase in the effective surface area of the modified electrode. The anodic transfer coefficient, detection limit and electron transfer rate constant of the reaction were also calculated.

Conclusion:

The paper reports the determination of epinephrine using reduced graphene oxide modified glassy carbon electrode through CV and DPV. The sensor exhibited excellent reproducibility and repeatability for the detection of epinephrine and also its simultaneous detection of ascorbic acid and uric acid, which coexist in the biological system.

Recent Advances in Electrochemical and Optical Sensing of Dopamine

Nowadays, several neurological disorders and neurocrine tumours are associated with dopamine (DA) concentrations in various biological fluids. Highly accurate and ultrasensitive detection of DA levels in different biological samples in real-time can change and improve the quality of a patient's life in addition to reducing the treatment cost. Therefore, the design and development of diagnostic tool for in vivo and in vitro monitoring of DA is of considerable clinical and pharmacological importance. In recent decades, a large number of techniques have been established for DA detection, including chromatography coupled to mass spectrometry, spectroscopic approaches, and electrochemical (EC) methods. These methods are effective, but most of them still have some drawbacks such as consuming time, effort, and money. Added to that, sometimes they need complex procedures to obtain good sensitivity and suffer from low selectivity due to interference from other biological species such as uric acid (UA) and ascorbic acid (AA). Advanced materials can offer remarkable opportunities to overcome drawbacks in conventional DA sensors. This review aims to explain challenges related to DA detection using different techniques, and to summarize and highlight recent advancements in materials used and approaches applied for several sensor surface modification for the monitoring of DA. Also, it focuses on the analytical features of the EC and optical-based sensing techniques available.

Multifunctional, fluorescent DNA-derived carbon dots for biomedical applications: bioimaging, luminescent DNA hydrogels, and dopamine detection

Here, we describe the synthesis of 2-3 nm, hydrophilic, blue fluorescence-emitting carbon dots (C-Dots, made using a DNA precursor) by the hydrothermal route from the gelling concentration of 2% (w/v) DNA. These dots exhibited highly efficient internalization in pathogenic fungal cells, negligible cytotoxicity, good PL stability, and high biocompatibility, thus demonstrating their potential as nanotrackers in microbial studies. Bioimaging was performed using Candida albicans as the representative for microbial pathogens. The novelty of these dots is that they formed fluorescent nanocomposite hydrogels with the same DNA much below the gelation concentration (1% w/v) and the tunable gels possessed strength between 20 and 80 Pa with the corresponding gelation temperature T_gel between 40 to 50 °C. The network density and gelation free energy data supported the superior crosslinking ability of these dots. The as-prepared hydrogels can replace the existing toxic quantum dot-based hydrogels for drug delivery. We also demonstrated the use of a DNA hydrogel-fabricated working electrode (DNA-C-Dot/ITO electrode) for the biosensing of dopamine. Our electrochemical biosensor had a detection limit of 5 × 10^-3 mM for dopamine. These multifunctional, fluorescent C-Dots and hydrogel after suitable conjugation or loading with molecules and drugs hold promising potential for further exploitation in bioimaging, targeted drug delivery, wound healing, and biosensing applications.

Hybrid Graphene/Conducting Polymer Strip Sensors for Sensitive and Selective Electrochemical Detection of Serotonin

There is an urgent need for electrochemical sensor materials that exhibit electrochemically compliant properties while also retaining high durability under physiological conditions. Herein, we demonstrate a novel strip-style electrochemical sensor using reduced graphene oxide (rGO) and poly(ethylene dioxythiophene)/poly(styrene sulfonic acid) (PEDOT/PSS) nanocomposite films. The fabricated rGO-PEDOT/PSS sensor with and without nafion has shown an effective electrochemical response for both selectivity and sensitivity of the serotonin (5-hydroxytryptamine, 5-HT) neurotransmitter. The developed high-performance hybrid graphene/conducting polymer strip sensors are likely to find applications as chip electrochemical sensor devices for patients diagnosed with Alzheimer's disease.

Synthesis and Characterization of Magnetic Fe3O4/Reduced Graphene Oxide and its Application in Determination of Dopamine

An electrochemical sensor to determine dopamine in the human body was fabricated based on modified iron oxide/reduced graphene oxide/glassy carbon electrode (Fe3O4/r-GO/GCE). Determination of dopamine is significance nowadays as the abnormal level may cause various mental health diseases as well as Parkinson’s disease. The Fe3O4/r-GO nanocomposite was synthesized via Hummer’s method with a slight modification and characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Brunauer Emmett-Teller (BET). The presence of Fe3O4 onto the surface of r-GO was confirmed by SEM analysis which shows the bulky porous sponge-like structure attached to an exfoliated sheet of r-GO. FTIR analysis proved the presence of the functional group in existing composites via oxidation process of graphene oxide and reduction process of reduced graphene oxide while the crystalline form of Fe3O4/r-GO was determined using XRD analysis. The diffraction peaks index to the cubic phase was noticeable indicating the successful crystallization of the composites. The catalytic activity of bare GCE and modified GCE (Fe3O4/r-GO/ GCE) were observed using electrochemical characterization of cyclic voltammetry, differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS) with optimum pH of 7, a concentration of 100 μM, and the scan rate of 250 mV s-1. The observed DPV response linearly depends on dopamine concentration in the range of 20-100 μM, with correlation coefficients of 0.9876. The detection limit obtained for the real sample analysis was found to be 0.569 μM while the limit of quantitation was 1.897 μM. The percentage of recovery, repeatability and reproducibility was 113, 82.81 and 7.19 %, respectively.

Electroanalysis of Catecholamine Drugs using Graphene Modified Electrodes

Background:

Catecholamine drugs are a family of electroactive pharmaceutics, which are widely analyzed through electrochemical methods. However, for low level online determination and monitoring of these compounds, which is very important for clinical and biological studies, modified electrodes having high signal to noise ratios are needed. Numerous materials including nanomaterials have been widely used as electrode modifies for these families during the years. Among them, graphene and its family, due to their remarkable properties in electrochemistry, were extensively used in modification of electrochemical sensors.

Objective:

In this review, working electrodes which have been modified with graphene and its derivatives and applied for electroanalyses of some important catecholamine drugs are considered.

Morphology-Dependent Electrochemical Sensing Properties of Iron Oxide-Graphene Oxide Nanohybrids for Dopamine and Uric Acid

Various morphologies of iron oxide nanoparticles (Fe2O3 NPs), including cubic, thorhombic and discal shapes were synthesized by a facile meta-ion mediated hydrothermal route. To further improve the electrochemical sensing properties, discal Fe2O3 NPs with the highest electrocatalytic activity were coupled with graphene oxide (GO) nanosheets. The surface morphology, microstructures and electrochemical properties of the obtained Fe2O3 NPs and Fe2O3/GO nanohybrids were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. As expected, the electrochemical performances were found to be highly related to morphology. The discal Fe2O3 NPs coupled with GO showed remarkable electrocatalytic activity toward the oxidation of dopamine (DA) and uric acid (UA), due to their excellent synergistic effect. The electrochemical responses of both DA and UA were linear to their concentrations in the ranges of 0.02-10 μM and 10-100 μM, with very low limits of detection (LOD) of 3.2 nM and 2.5 nM for DA and UA, respectively. Moreover, the d-Fe2O3/GO nanohybrids showed good selectivity and reproducibility. The proposed d-Fe2O3/GO/GCE realized the simultaneous detection of DA and UA in human serum and urine samples with satisfactory recoveries.

Electronic transport in a graphene single layer: application in amino acid sensing

We modeled a type of field-effect transistor device based on graphene for the recognition of amino acids with a potential application in the building of a protein sequencer. The theoretical model used was a combination of density functional theory (DFT) with the non-equilibrium Green's function (NEGF) in order to describe the coherent transport in molecular devices. First, we studied the physisorption of each amino acid on a graphene sheet and we reported the adsorption energy, the adsorption distances, the equilibrium configuration and the charge transfer of ten amino acids that can be considered as representative of all of the amino acids: histidine (His), alanine (Ala), aspartic acid (Asp), tyrosine (Tyr), arginine (Arg), glutamic acid (Glu), glycine (Gly), phenylalanine (Phe), proline (Pro) and lysine (Lys). As a result, significant differences were found in the density of states (DOS) after adsorption and there was a change in the semi-metallic character of the graphene due to the lysine and arginine interactions. Furthermore, we noticed changes in the electrical characteristics of the devices, as the amino acids adsorbed onto the surface of the graphene. The curves of current vs. bias voltage (I-Vb) display a distinct response for each amino acid, i.e. the I-Vb curves produce a characteristic footprint for each amino acid. We identified a possible rectification mechanism related to the voltage profile asymmetry, where the amino acids can control the transport characteristics in the device, i.e. Lys and Phe amino acids physisorbed on graphene act as a molecular diode, where electrons can easily flow in one direction and decrease in the other. This may be promising for the prospect of biosensors: graphene could be used as an amino acid detector.

Carbon Black-Carbon Nanotube Co-Doped Polyimide Sensors for Simultaneous Determination of Ascorbic Acid, Uric Acid, and Dopamine

Carbon black (CB) and carbon nanotube (CNT) co-doped polyimide (PI) modified glassy carbon electrode (CB-CNT/PI/GCE) was first prepared for the simultaneous determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). The CB-CNT/PI/GCE exhibited persistent electrochemical behavior and excellent catalytic activities. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used for the simultaneous detection of AA, DA, and UA in their ternary mixture. The peak separations between AA and DA, and DA and UA, are up to 166 mV and 148 mV, respectively. The CB-CNT/PI/GCE exhibited high sensitivity to DA and UA, with the detection limit of 1.9 µM and 3 µM, respectively. In addition, the CB-CNT/PI/GCE showed sufficient selectivity and long-term stability, and was applicable to detect AA, DA, and UA in human urine sample.

Silver nanoparticles decorated eggshell membrane as an effective platform for interference free sensing of dopamine

In this paper a simple electrochemical sensing of dopamine by a new effective immobilization of tyrosinase (Tyr) enzyme on eggshell membrane (ESM) along with silver nanoparticles (AgNPs) is reported. The modified membrane was characterized by scanning electron microscope (SEM), energy dispersive spectroscopy (EDAX), X-Ray diffraction (XRD). A simple solution based approach was used to prepare AgNPs on biomembrane followed by glutaraldehyde activation to immobilize Tyr on the nanoparticles decorated ESM. The direct electrochemistry of DA oxidation was performed through cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Characterization of membrane was accomplished by electrochemical impedance spectroscopy (EIS). Prepared electrode showed very good stability, reproducibility, high selectivity, easy preparation and regeneration of electrode. The proposed sensor exhibited low detection limits 1.7ngL^-1 with wide linear range 10-1000 ngL^-1, excellent sensitivity (14.28µA µgL^-1cm^-2) with good storage and operational stabilities. The accurate measurement of dopamine in blood serum and good recoveries in spiked serum samples ensured great potential for medical diagnostics.

Development of an Fe3O4@Cu silicate based sensing platform for the electrochemical sensing of dopamine

Abnormal levels of dopamine (DA) in body fluids is an indication of serious health issues, hence development of highly sensitive platforms for the precise detection of DA is highly essential. Herein, we demonstrate an Fe₃O₄@Cu silicate based electrochemical sensing platform for the detection of DA. Morphology and BET analysis shows the formation of ∼320 nm sized sea urchin-like Fe₃O₄@Cu silicate core–shell nanostructures with a 174.5 m² g⁻¹ surface area. Compared to Fe₃O₄ and Fe₃O₄@SiO₂, the Fe₃O₄@Cu silicate urchins delivered enhanced performance towards the electrochemical sensing of DA in neutral pH. The Fe₃O₄@Cu silicate sensor has a 1.37 μA μM⁻¹ cm⁻² sensitivity, 100–700 μM linear range and 3.2 μM limit of detection (LOD). In addition, the proposed Fe₃O₄@Cu silicate DA sensor also has good stability, selectivity, reproducibility and repeatability. The presence of Cu in Fe₃O₄@Cu silicate and the negatively charged surface of the Cu silicate shell play a vital role in achieving high selectivity and sensitivity during DA sensing. The current investigation not only represents the development of a highly selective DA sensor but also directs towards the possibility for the fabrication of other Cu silicate based core–shell nanostructures for the precise detection of DA.

Abnormal levels of dopamine (DA) in body fluids is an indication of serious health issues, hence development of highly sensitive platforms for the precise detection of DA is highly essential.

Trace level electrochemical determination of the neurotransmitter dopamine in biological samples based on iron oxide nanoparticle decorated graphene sheets

The trace level electrochemical determination of dopamine in biological samples based on an iron oxide nanoparticle-capped graphene sheet modified electrode.

Chemical sensing with 2D materials

During the last decade, two-dimensional materials (2DMs) have attracted great attention due to their unique chemical and physical properties, which make them appealing platforms for diverse applications in sensing of gas, metal ions as well as relevant chemical entities.

Iron-Based Nanomaterials/Graphene Composites for Advanced Electrochemical Sensors

Iron oxide nanostructures (IONs) in combination with graphene or its derivatives-e.g., graphene oxide and reduced graphene oxide-hold great promise toward engineering of efficient nanocomposites for enhancing the performance of advanced devices in many applicative fields. Due to the peculiar electrical and electrocatalytic properties displayed by composite structures in nanoscale dimensions, increasing efforts have been directed in recent years toward tailoring the properties of IONs-graphene based nanocomposites for developing more efficient electrochemical sensors. In the present feature paper, we first reviewed the various routes for synthesizing IONs-graphene nanostructures, highlighting advantages, disadvantages and the key synthesis parameters for each method. Then, a comprehensive discussion is presented in the case of application of IONs-graphene based composites in electrochemical sensors for the determination of various kinds of (bio)chemical substances.