Aqueous Adsorption of Heavy Metals on Metal Sulfide Nanomaterials: Synthesis and Application

CoSn(OH)6 nanocubes as a solid sorbent for the effective preconcentration of copper ions in cinnamon (Cinnamomum zeylanicum) extract

This study was aimed at developing a simple and efficient CoSn(OH)6 nanocubes-based preconcentration method for the preconcentration of copper ions from cinnamon extracts for determination by flame atomic absorption spectrometry. The cube-shaped sorbent was synthesized using the simple stoichiometric co-precipitation method under ambient conditions. Experimental factors of the method were evaluated with a comprehensive optimization approach to maximize the extraction efficiency for the analyte. Under the optimal conditions, the limit of detection (LOD), limit of quantitation (LOQ), and linear dynamic range were recorded as 0.98 µg/L, 3.28 µg/L, and 4.0-75 µg/L, respectively. The enhancement factor was calculated as 101.6-fold by comparing the LODs of the optimized and direct analysis systems. Percent recoveries were found to be within an acceptable range (77.6-115 %), with high repeatability using matrix matching calibration strategy. Results validated the proposed method as a highly efficient extraction approach for the monitoring of copper ions in herbal cinnamon extracts.

pH-Dependent selective extraction of gold(iii) from synthetic solution and computer motherboard leachate using a hybrid nanocomposite

Recycling gold from electronic waste offers significant benefits for both environmental protection and resource sustainability. However, this process presents considerable challenges due to high costs, prolonged processing times, and interference from coexisting metals. In this study, we synthesized a hybrid mesoporous nanocomposite comprising platelets-like CoNi2S4 incorporated with g-C3N4 nanosheets (CoNi2S4@g-C3N4) for the selective recovery of gold (Au(iii)) ions from spent computer motherboards. Comprehensive characterization of the CoNi2S4@g-C3N4 nanocomposite was conducted, including its physicochemical properties, textural and structural characteristics, morphology, and elemental composition. The CoNi2S4@g-C3N4 extractor demonstrated an exceptional adsorption capacity of 200.6 mg g-1, with high selectivity at pH 2, rapid equilibrium time of 60 minutes, and satisfactory reusability for over ten cycles. Adsorption isotherm and kinetic studies revealed that the CoNi2S4@g-C3N4 nanocomposite adheres to the Langmuir adsorption model and the pseudo-second-order kinetic model for Au(iii) ion adsorption. Overall, this study introduces a viable adsorbent that shows considerable promise for industrial-scale Au(iii) extraction from e-waste.

Ultrafast and highly efficient Cd(II) and Pb(II) removal by magnetic adsorbents derived from gypsum and corncob: Performances and mechanisms

The utilization of gypsum and biomass in environmental remediation has become a novel approach to promote waste recycling. Generally, raw waste materials exhibit limited adsorption capacity for heavy metal ions (HMIs) and often result in poor solid-liquid separation. In this study, through co-pyrolysis with corncob waste, titanium gypsum (TiG) was transformed into magnetic adsorbents (GCx, where x denotes the proportion of corncob in the gypsum-corncob mixture) for the removal of Cd(II) and Pb(II). GC10, the optimal adsorbent, which was composed primarily of anhydrite, calcium sulfide, and magnetic Fe3O4, exhibited significantly faster adsorption kinetics (rate constant k1 was 218 times and 9 times of raw TiG for Cd(II) and Pb(II)) and higher adsorption capacity (Qe exceeded 200 mg/g for Cd(II) and 400 mg/g for Pb(II)) than raw TiG and previous adsorbents. Cd(II) removal was more profoundly inhibited in a Cd(II) + Pb(II) binary system, suggesting that GC10 showed better selectivity for Pb(II). Moreover, GC10 could be easily separated from purified water for further recovery, due to its high saturation magnetization value (6.3 emu/g). The superior removal capabilities of GC10 were due to adsorption and surface precipitation of metal sulfides and metal sulfates on the adsorbent surface. Overall, these waste-derived magnetic adsorbents provide a novel and sustainable approach to waste recycling and the deep purification of multiple HMIs.

Conversion of seaweed waste to biochar for the removal of heavy metal ions from aqueous solution: A sustainable method to address eutrophication problem in water bodies

The present study investigated the sustainable approach for wastewater treatment using waste algal blooms. The current study investigated the removal of toxic metals namely chromium (Cr), nickel (Ni), and zinc (Zn) from aqueous solutions in batch and column studies using biochar produced by the marine algae Ulva reticulata. SEM/EDX, FTIR, and XRD were used to examine the adsorbents' properties and stability. The removal efficiency of toxic metals in batch operations was investigated by varying the parameters, which included pH, biochar dose, initial metal ion concentration, and contact time. Similarly, in the column study, the removal efficiency of heavy metal ions was investigated by varying bed height, flow rate, and initial metal ion concentration. Response Surface Methodology (Central Composite Design (CCD)) was used to confirm the linearity between the observed and estimated values of the adsorption quantity. The packed bed column demonstrated successful removal rates of 90.38% for Cr, 91.23% for Ni, and 89.92% for Zn heavy metals from aqueous solutions, under a controlled environment. The breakthrough analysis also shows that the Thomas and Adams-Bohart models best fit the regression values, allowing prior breakthroughs in the packed bed column to be predicted. Desorption studies were conducted to understand sorption and elution during different regeneration cycles. Adding 0.3 N sulfuric acid over 40 min resulted in the highest desorption rate of the column and adsorbent used for all three metal ions.

Layered metal sulfides with MaSbc- framework (M = Sb, In, Sn) as ion exchangers for the removal of Cs(Ⅰ) and Sr(Ⅱ) from radioactive effluents: a review

Nuclear power has emerged as a pivotal contributor to the global electricity supply owing to its high efficiency and low-carbon characteristics. However, the rapid expansion of the nuclear industry has resulted in the production of a significant amount of hazardous effluents that contain various radionuclides, such as 137Cs and 90Sr. Effectively removing 137Cs and 90Sr from radioactive effluents prior to discharge is a critical challenge. Layered metal sulfides exhibit significant potential as ion exchangers for the efficient uptake of Cs+ and Sr2+ from aqueous solutions owing to their open and exchangeable frameworks and the distinctive properties of their soft S2- ligands. This review provides a detailed account of layered metal sulfides with MaSb c- frameworks (M = Sb, In, Sn), including their synthesis methods, structural characteristics, and Cs+ and Sr2+ removal efficiencies. Furthermore, we highlight the advantages of layered metal sulfides, such as their relatively high ion exchange capacities, broad active pH ranges, and structural stability against acid and radiation, through a comparative evaluation with other conventional ion exchangers. Finally, we discuss the challenges regarding the practical application of layered metal sulfides in radionuclide scavenging.

Analytical application of flower-shaped nickel nanomaterial for the preconcentration of manganese in domestic wastewater samples

In this study, detection sensitivity of the conventional flame atomic absorption spectrophotometer (FAAS) for the determination of manganese (Mn2+) was enhanced by employing a preconcentration method from wastewater samples. Flower-shaped Ni(OH)2 nanomaterials were synthesized and used as sorbent material in preconcentration procedure. With the aim of attaining optimum experimental conditions, effective parameters of extraction method were optimized and these included pH of buffer solution, desorption solvent concentration and volume, mixing type and period, nanoflower amount, and sample volume. The detection limit of the optimized method was determined to be 2.2 μg L-1, and this correlated to about 41-fold enhancement in detection power relative to direct FAAS measurement. Domestic wastewater was used to test the feasibility of the proposed method to real samples by performing spike recovery experiments. The wastewater sample was spiked at four different concentrations of manganese, and the percent recoveries determined were in the range of 95-120%.

Valorisation of spent tire rubber as carbon adsorbents for Pb(II) and W(VI) in the framework of a Circular Economy

Spent tire rubber-derived chars and their corresponding H3PO4 and CO2-activated chars were used as adsorbents in the recovery of Pb(II) ion and (W(VI)) oxyanion from synthetic solutions. The developed chars (both raw and activated) were thoroughly characterized to have insight about their textural and surface chemistry properties. H3PO4-activated chars presented lower surface areas than the raw chars and an acidic surface chemistry which affected the performance of these samples as they showed the lowest removals of the metallic ions. On the other hand, CO2-activated chars presented increased surface areas and increased mineral content compared to the raw chars, having presented higher uptake capacities for both Pb(II) (103-116 mg/g) and W(VI) (27-31 mg/g) ions. Cation exchange with Ca, Mg and Zn ions was appointed as a mechanism for Pb removal, as well as surface precipitation in the form of hydrocerussite (Pb3(CO3)2(OH)2). W(VI) adsorption might have been ruled by strong electrostatic attractions between the negatively charged tungstate species and the highly positively charged carbons' surface.The results shown in this work allow concluding that the valorisation of spent tire rubber through pyrolysis and the subsequent activation of the obtained chars is an alternative and a feasible option to generate adsorbent materials with a high uptake capacity of critical metallic elements.

Coating zirconium oxide-nanocomposite with humic acid for recovery of mercury and chromium in hazardous waste of chemical oxygen demand test

Hazardous waste of chemical oxygen demand (COD) test (HW_COD) is one of the most common laboratory wastewaters, containing large amounts of H₂SO₄ and highly toxic Cr³⁺ and Hg²⁺. Current treatment methods suffered from incomplete removal of Cr³⁺ and high-cost. Herein, a humic acid-coated zirconium oxide-resin nanocomposite (HA-HZO-201) was fabricated for efficient recovery of Cr³⁺ and Hg²⁺ in HW_COD. The synthesized HA-HZO-201 shows excellent tolerance to wide pH range (1-5) and high salinity (3.5 mol/L NaCl), as well as adsorption capacity for Cr³⁺ (37.5 mg/g) and Hg²⁺ (121.3 mg/g). After treating with HA-HZO-201 by using a fixed-bed adsorption procedure, the final Cr³⁺ and Hg²⁺ concentrations in HW_COD decreased to 0.28 and 0.02 mg/L, respectively. In addition, the HA-HZO-201 can be regenerated by desorption and recovery of Cr³⁺ and Hg²⁺ using HNO₃ and thiourea as eluents, respectively. After 5 cycles of adsorption/desorption, the removal efficiencies still reach up to 86.0% for Cr³⁺ and 89.7% for Hg²⁺, indicating an excellent regeneration of HA-HZO-201. We hope this work open new opportunities for treatment of HW_COD with high-efficiency and low-cost.

Water Cleaning by a Continuous Fixed-Bed Column for Cr(VI) Eco-Adsorption with Green Adsorbent-Based Biomass: An Experimental Modeling Study

In this study, chromate adsorption onto red peanut skin (RPS) was investigated in a fixed-bed column; FTIR, PZC, SEM, DLS, and BET were used to evaluate its adsorption properties. The experiments were conducted to determine the effect of physical parameters, including the inlet initial Cr(VI) concentration (100–500 mg L−1), bed height (10–20 cm), and feed flow rate (13.59–23.45 mL min−1). They were carried out to predict breakthrough curves. The adsorption capacity coefficients were determined using the most widely used Bohart–Adams model. It was tested to fit experimental data, for a better understand the dynamic behavior, and for further optimize column performance. It was found that the Cr(VI) uptake decreases when increasing the flow rate and that high chromate concentration and bed height consequently increase the column’s life span. A high column adsorption capacity can be achieved with a higher Cr(VI) concentration due to the higher driving force. The results indicated that the Bohart–Adams model provides a good description (R2 > 0.98) of the experimental data of the Cr(VI)’s removal from the aqueous solution on the RPS suggesting that the surface diffusion is the rate-limiting step in the continues adsorption process.. Breakthrough adsorption capacity is crucial for comparing RPS with other similar materials. Indeed, possible mechanisms have been suggested for illustrating adsorption onto RPS. The obtained results showed significant potential of 26.23 mg g−1 of RPS on Cr(VI) elimination at a natural pH of 5.35. Furthermore, this global investigation allowed for the design of a promising low-cost material for the future scale-up of cleaning wastewater polluted by metal and determine the properly conditions for operating column adsorption. This material provides an economical, efficient means of eliminating pollutants, thus meeting the main aims of the UN Sustainable Development Goals (UN SDGs).

Biopolymeric Ni3S4/Ag2S/TiO2/Calcium Alginate Aerogel for the Decontamination of Pharmaceutical Drug and Microbial Pollutants from Wastewater

The ubiquitous presence of pharmaceutical drugs and microbes in the water is leading to the development of drug resistant microbes. Therefore, efficient materials that can remove or inactivate the drug and microbe contaminants are required. In this work, nickel sulfide/calcium alginate (Ni3S4/CA), silver sulfide/calcium alginate (Ag2S/CA), modified titanium dioxide/calcium alginate (TiO2/CA), and Ni3S4/Ag2S/TiO2/calcium alginate (Ni3S4/Ag2S/TiO2/CA) aerogels have been synthesized for the removal of the oxytetracycline (OTC) drug and microbial contaminants from real beverage industry wastewater. The results revealed that Ni3S4/Ag2S/TiO2/CA aerogel is highly efficient for OTC adsorption and inactivation of microbes compared to Ni3S4/CA, Ag2S/CA and TiO2/CA aerogels. The OTC adsorption depends greatly on the solution pH, and optimum OTC removal was observed at pH 6 in its zwitterionic (OTC±) form. The formation of H-bonding and n-π electron donor-acceptors is possible to a considerable extent due to the presence of the double bond benzene ring, oxygen and nitrogen, sulfur-containing functional groups on the OTC molecules, and the Ni3S4/Ag2S/TiO2/CA aerogel. Based on the statistical analysis, root-mean-square deviation (RMSD), chi square (χ2) values, and higher correlation coefficient (R2) values, the Redlich−Peterson isotherm model and Elovich kinetic model are most suited to modelling the OTC adsorption onto Ni3S4/Ag2S/TiO2/CA. The prepared aerogels’ excellent antimicrobial activity is observed in the dark and with solar light irradiation. The zone of inhibition analysis revealed that the antimicrobial activity of the aerogels is in the following order: Ni3S4/Ag2S/TiO2/CA > TiO2/CA > Ag2S/CA > Ni3S4/CA, respectively. Moreover, the antimicrobial results demonstrated that reactive oxygen species, electrons, and active radical species are responsible for growth inhibition and killing of the microbes. These results indicated that Ni3S4/Ag2S/TiO2/CA aerogel is highly efficient in decontaminating pollutants from wastewater.

Application of Lactic Acid Bacteria (LAB) in Sustainable Agriculture: Advantages and Limitations

Lactic acid bacteria (LAB) are significant groups of probiotic organisms in fermented food and are generally considered safe. LAB regulate soil organic matter and the biochemical cycle, detoxify hazardous chemicals, and enhance plant health. They are found in decomposing plants, traditional fermented milk products, and normal human gastrointestinal and vaginal flora. Exploring LAB identified in unknown niches may lead to isolating unique species. However, their classification is quite complex, and they are adapted to high sugar concentrations and acidic environments. LAB strains are considered promising candidates for sustainable agriculture, and they promote soil health and fertility. Therefore, they have received much attention regarding sustainable agriculture. LAB metabolites promote plant growth and stimulate shoot and root growth. As fertilizers, LAB can promote biodegradation, accelerate the soil organic content, and produce organic acid and bacteriocin metabolites. However, LAB show an antagonistic effect against phytopathogens, inhibiting fungal and bacterial populations in the rhizosphere and phyllosphere. Several studies have proposed the LAB bioremediation efficiency and detoxification of heavy metals and mycotoxins. However, LAB genetic manipulation and metabolic engineered tools provide efficient cell factories tailor-made to produce beneficial industrial and agro-products. This review discusses lactic acid bacteria advantages and limitations in sustainable agricultural development.

Preparation of Magnetic MIL-68(Ga) Metal-Organic Framework and Heavy Metal Ion Removal Application

A magnetic metal-organic framework nanocomposite (magnetic MIL-68(Ga)) was synthesized through a "one pot" reaction and used for heavy metal ion removal. The morphology and elemental properties of the nanocomposite were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), X-ray powder diffraction (XRD), as well as zeta potential. Moreover, the factors affecting the adsorption capacity of the nanocomposite, including time, pH, metal ion type and concentration, were studied. It was found that the adsorption capacity of magnetic MIL-68(Ga) for Pb²⁺ and Cu²⁺ was 220 and 130 mg/g, respectively. Notably, the magnetic adsorbents could be separated easily using an external magnetic field, regenerated by ethylenediaminetetraacetic acid disodium salt (EDTA-Na₂) and reused three times, in favor of practical application. This study provides a reference for the rapid separation and purification of heavy metal ions from wastewater.

Heavy metal pollution and the role of inorganic nanomaterials in environmental remediation

Contamination of water and soil with toxic heavy metals is a major threat to human health. Although extensive work has been performed on reporting heavy metal pollutions globally, there are limited review articles on addressing this pernicious phenomenon. This paper reviews inorganic nanoparticles and provides a framework for their qualities required as good nanoadsorbents for efficient removal of heavy metals from water. Different inorganic nanoparticles including metals, metal oxides and metal sulfides nanoparticles have been applied as nanoadsorbents to successfully treat water with high contaminations of heavy metals at concentrations greater than 100 mg l^-1, achieving high adsorption capacities up to 3449 mg g^-1. It has been identified that the synthesis method, selectivity, stability, regeneration and reusability, and adsorbent separation from solution are critical parameters in deciding on the quality of inorganic nanoadsorbents. Surface functionalized nanoadsorbents were found to possess high selectivity and capacity for heavy metals removal from water even at a very low adsorbent dosage of less than 2 g l^-1, which makes them better than conventional adsorbents in environmental remediation.