Ozonation using a stainless-steel membrane contactor: Gas-liquid mass transfer and pharmaceuticals removal from secondary-treated municipal wastewater

A tubular porous stainless steel membrane contactor was characterized in terms of ozone-water mass transport, as well as its application in removing 23 pharmaceuticals (PhACs) detected in the secondary-treated municipal wastewater, under continuous mode operation. The volumetric mass transfer coefficient (KLa) was evaluated based on liquid flow rate, gas flow rate, and ozone gas concentration. The KLa values were substantially improved with an increment in liquid flow rate (1.6 times from 30 to 70 dm3 h-1) and gas flow rate (3.6 times from 0.30 to 0.85 Ndm3 min-1) due to the improved mixing in the gas-liquid interface. For the lowest liquid flow rate (30 dm3 h-1), the water phase boundary layer (82%) exhibited the major ozone transfer resistance, but it became almost comparable with membrane resistance for the highest liquid flow rate (70 dm3 h-1). Additionally, the influence of the specific ozone dose (0.39, 0.53, and 0.69 g O3 g DOC-1) and ozone inlet gas concentration ( [Formula: see text]  = 27, 80, and 134 g Nm-3) were investigated in the elimination of 23 PhACs found in secondary-treated municipal wastewater. An ozone dose of 0.69 g O3 g DOC-1 and residence time of 60 s resulted in the removal of 12 out of the 23 compounds over 80%, while 17 compounds were abated above 60%. The elimination of PhACs was strongly correlated with kinetic reaction constants values with ozone and hydroxyl radicals (kO3 and kHO•), leading to a characteristic elimination pattern for each group of contaminants. This study demonstrates the high potential of membrane contactors as an appealing alternative for ozone-driven wastewater treatment.

Searching for pharmaceutically active products and metabolites in environmental waters of Peru by HRMS-based screening: Proposal for future monitoring and environmental risk assessment

The presence of pharmaceutical active products (PhACs) in the aquatic environment is a matter of current concern, and there is an increasing trend to include these compounds in water quality monitoring programs and environmental risk assessments. Several studies have reported the presence of PhACs in environmental waters worldwide, but only a few studies have focused on Latin American countries. Thus, available information on the occurrence of parent pharmaceuticals, especially their metabolites, is very scarce. Peru is one of the less monitored countries in terms of contaminants of emerging concern (CECs) in waters, and only one study has been found, which was focused on the quantification of selected PhACs in urban wastewater and surface water. The aim of this work is to complement the previous data reported on PhACs in the aquatic environment by application of a wide-scope high-resolution (HRMS)-based screening, making use of target and suspect approaches. In the present work, 30 pharmaceuticals, drugs or other compounds (sweeteners, UV filters, etc.) and 21 metabolites have been identified, with antibiotics (and metabolites) being the most prevalent compounds. The use of liquid chromatography (LC) coupled to ion mobility-HRMS allowed the tentative identification of parent compounds and metabolites, for which the analytical reference standard was not available, with a high level of confidence in their identification. Based on the results obtained, a strategy for the monitoring of PhACs and relevant metabolites in environmental waters from Peru and for subsequent risk assessment is proposed. Our data will also help to focus future studies to evaluate the removal efficiency of wastewater treatment plants and the impact of treated water in receiving water bodies.

Methods involved in the treatment of four representative pharmaceuticals in hospital wastewater using sonochemical and biological processes

A primary pollution source by pharmaceuticals is hospital wastewater (HWW). Herein, the methods involved in the action of a biological system (BS, aerobic activated sludge) or a sonochemical treatment (US, 375 kHz and 30.8 W), for degrading four relevant pharmaceuticals (azithromycin, ciprofloxacin, paracetamol, and valsartan) in HWW, are shown. Before treatment of HWW, the correct performance of BS was assessed using glucose as a reference substance, monitoring oxygen consumption, and organic carbon removal. Meanwhile, for US, a preliminary test using ciprofloxacin in distilled water was carried out. The determination of risk quotients (RQ) and theoretical analyses about reactive moieties on these target substances are also presented. For both, the degradation of the pharmaceuticals and the calculation of RQ, analyses were performed by LC-MS/MS. The BS action decreased the concentration of paracetamol and valsartan by ∼96 and 86%, respectively. However, a poor action on azithromycin (2% removal) was found, whereas ciprofloxacin concentration increased ∼20%; leading to an RQ value of 1.61 (high risk) for the pharmaceuticals mixture. The analyses using a biodegradation pathway predictor (EAWAG-BDD methodology) revealed that the amide group on paracetamol and alkyl moieties on valsartan could experience aerobic biotransformations. In turn, US action decreased the concentration of the four pharmaceuticals (removals > 60% for azithromycin, ciprofloxacin, and paracetamol), diminishing the environmental risk (RQ: 0.51 for the target pharmaceuticals mixture). Atomic charge analyses (based on the electronegativity equalization method) were performed, showing that the amino-sugar on azithromycin; piperazyl ring, and double bond close to the two carbonyls on ciprofloxacin, acetamide group on paracetamol, and the alkyl moieties bonded to the amide group of valsartan are the most susceptible moieties to attacks by sonogenerated radicals. The LC-MS/MS analytical methodology, RQ calculations, and theoretical analyses allowed for determining the degrading performance of BS and US toward the target pollutants in HWW.•Biological and sonochemical treatments as useful methods for degrading 4 representative pharmaceuticals are presented.•Sonochemical treatment had higher degrading action than the biological one on the target pharmaceuticals.•Methodologies for risk environmental calculation and identification of moieties on the pharmaceuticals susceptible to radical attacks are shown.

Removal efficiency for emerging contaminants in a WWTP from Madrid (Spain) after secondary and tertiary treatment and environmental impact on the Manzanares River

The effluents from wastewater treatment plants (WWTPs) can be an important contamination source for receiving waters. In this work, a comprehensive study on the impact of a WWTP from Madrid on the aquatic environment has been performed, including a wide number of pharmaceuticals and pesticides, among them those included in the European Watch List. 24-h composite samples of influent (IWW) and effluent wastewater after secondary (EWW2) and after secondary + tertiary treatment (EWW3) were monitored along two campaigns. Average weekly concentrations in IWW and EWW2 and EWW3 allowed estimating the removal efficiency of the WWTP for pharmaceutical active substances (PhACs). In addition, the impact of EWW3 on the water quality of the Manzanares River was assessed, in terms of PhAC and pesticide concentrations, through analysis of the river water collected upstream and downstream of the discharge point. After a preliminary risk assessment, a detailed evaluation of the impact on the aquatic environment, including a toxicological study and screening of pharmaceutical metabolites, was made for the seven most relevant PhACs: sulfamethoxazole, azithromycin and clarithromycin (antibiotics), metoprolol (antihypertensive), diclofenac (anti-inflammatory/analgesic), irbesartan (antihypertensive), and the antidepressant venlafaxine. Among selected PhACs, irbesartan, clarithromycin and venlafaxine presented moderate or high risk in the river water downstream of the discharge. Albeit no acute toxicity was detected, more detailed studies should be carried out for these substances, including additional toxicological studies, to set up potential sublethal and chronic effects on aquatic organisms.

Pharmaceuticals and environmental risk assessment in municipal wastewater treatment plants and rivers from Peru

This is the first study dealing with removal of the pharmaceutical substances in municipal wastewater treatment plants (MWWTPs) from Peru and the impact of these compounds in surface waters receiving treated wastewater. To this aim, samples from MWWTP of Lima (Peruvian Coast), MWWTP of Cusco, Puno and Juliaca (Peruvian Highlands), as well surface water (confluence of Torococha and Coata rivers in Juliaca) were analyzed. A total of 38 target pharmaceuticals were included in this study and were determined by Liquid Chromatography coupled to tandem Mass Spectrometry (LC-MS/MS). Around 60% and 75% of the target pharmaceuticals could be quantified in surface water and MWWTPs, respectively. Acetaminophen was the drug found at the highest concentration, and it was present in all the treated wastewater samples reaching average values above 100 μg/L in the department of Puno. The gabapentin anti-epileptic drug (up to 11.85 μg/L in MWWTP Lima) and the antibiotics clarithromycin, trimethoprim, ciprofloxacin, sulfamethoxazole and azithromycin (1.86 to 4.47 μg/L in MWWTP Lima) were also found at moderate concentrations in the treated wastewater. In surface water, the highest concentration corresponded also to acetaminophen (28.70 μg/L) followed by sulfamethoxazole (4.36 μg/L). As regards the pharmaceuticals removal, data of this work showed that the MWWTP Cusco (aerobic biologic process by synthetic trickling filters as secondary treatment) was more efficient than the MWWTP Lima (a preliminary treatment that combines grilles, sand trap, degreaser-aerated and sieved of 1.0 mm). However, many pharmaceuticals (around 50% of the compounds investigated) presented concentrations in treated wastewater similar or even higher than in influent wastewater. The environmental ecological risk of pharmaceuticals was assessed based on calculated Risk Quotient (RQ) in the treated wastewater and surface water from the concentration data found in the samples. According to our data, three antibiotics (clarithromycin, ciprofloxacin, clindamycin) and the analgesic acetaminophen posed high environmental risk (RQ ≥ 1) on the aquatic environment. In the river, all antibiotics (except norfloxacin) as well as the analgesic-anti-inflammatory compounds acetaminophen, diclofenac posed a high environmental risk (RQ ≥ 1). Based on data reported in this work for the first time in water samples from Peru, it can be deduced that the treatment processes applied in important cities from Peru are not enough efficient to remove pharmaceuticals in wastewater. As a consequence, severe environmental risks associated to the presence of pharmaceuticals in treated wastewater and surface water are expected; so complementary treatment processes should be implemented in the MWWTPs for a more efficient elimination of these compounds.

The role of analytical chemistry in exposure science: Focus on the aquatic environment

Exposure science, in its broadest sense, studies the interactions between stressors (chemical, biological, and physical agents) and receptors (e.g. humans and other living organisms, and non-living items like buildings), together with the associated pathways and processes potentially leading to negative effects on human health and the environment. The aquatic environment may contain thousands of compounds, many of them still unknown, that can pose a risk to ecosystems and human health. Due to the unquestionable importance of the aquatic environment, one of the main challenges in the field of exposure science is the comprehensive characterization and evaluation of complex environmental mixtures beyond the classical/priority contaminants to new emerging contaminants. The role of advanced analytical chemistry to identify and quantify potential chemical risks, that might cause adverse effects to the aquatic environment, is essential. In this paper, we present the strategies and tools that analytical chemistry has nowadays, focused on chromatography hyphenated to (high-resolution) mass spectrometry because of its relevance in this field. Key issues, such as the application of effect direct analysis to reduce the complexity of the sample, the investigation of the huge number of transformation/degradation products that may be present in the aquatic environment, the analysis of urban wastewater as a source of valuable information on our lifestyle and substances we consumed and/or are exposed to, or the monitoring of drinking water, are discussed in this article. The trends and perspectives for the next few years are also highlighted, when it is expected that new developments and tools will allow a better knowledge of chemical composition in the aquatic environment. This will help regulatory authorities to protect water bodies and to advance towards improved regulations that enable practical and efficient abatements for environmental and public health protection.

Occurrence of antibiotics and bacterial resistance in wastewater and sea water from the Antarctic

The potential presence of introduced antibiotics in the aquatic environment is a hot topic of concern, particularly in the Antarctic, a highly vulnerable area protected under the Madrid protocol. The increasing presence of human population, especially during summer, might led to the appearance of pharmaceuticals in wastewater. The previous discovery of Escherichia coli strains resistant to antibiotics in sea water and wastewater collected in King George Island motivated our investigation on antibiotics occurrence in these samples. The application of a multi-residue LCMS/MS method for 20 antibiotics, revealed the presence of 8 compounds in treated wastewater, mainly the quinolones ciprofloxacin and norfloxacin (92% and 54% of the samples analyzed, average concentrations 0.89 μg/L and 0.75 μg/L, respectively) and the macrolides azithromycin and clarithromycin (15% positive samples, and average concentrations near 0.4 μg/L), and erythromycin (38% positive samples, average concentration 0.003 μg/L). Metronidazole and clindamycin were found in one sample, at 0.17 and 0.1 μg/L, respectively; and trimethoprim in two samples, at 0.001 μg/L. Analysis of sea water collected near the outfall of the wastewater discharges also showed the sporadic presence of 3 antibiotics (ciprofloxacin, clindamycin, trimethoprim) at low ng/L level, illustrating the impact of pharmaceuticals consumption and the poor removal of these compounds in conventional WWTPs. The most widespread antibiotic in sea water was ciprofloxacin, which was found in 15 out of 34 sea water samples analyzed, at concentrations ranging from 4 to 218 ng/L. Bacteria resistance was observed for some antibiotics identified in the samples (e.g. trimetropim and nalidixic acid -a first generation quinolone). However, resistance to some groups of antibiotics could not be correlated to their presence in the water samples due to analytical limitations (penicillins, tetraciclines). On the contrary, for some groups of antibiotics detected in samples (macrolides), the antibacterial activity against E. Coli was not investigated because these antibiotics do not include this bacterial species in their spectrum of activity. Our preliminary data demonstrate that antibiotics occurrence in the Antarctic aquatic environment is an issue that needs to be properly addressed. Periodical monitoring of water samples and the implementation of additional treatments in the WWTPs are recommended as a first step to prevent potential problems related to the presence of antibiotics and other emerging contaminants in the near future in Antarctica.

'An investigation into the occurrence and removal of pharmaceuticals in Colombian wastewater'

In this work, the presence of 20 pharmaceuticals in wastewater from Colombia is investigated. Several widely consumed compounds have been detected in wastewater samples from different origins and geographical areas in Colombia. The studied pharmaceuticals included antibiotics, analgesics and anti-inflammatories, cholesterol lowering statin drugs, lipid regulators, and anti-depressants. The investigated samples were urban wastewater collected during one whole week before (influent) and after treatment (effluent) in the wastewater treatment plants (WWTPs) of Bogotá and Medellin. Raw wastewater from the Hospital of Tumaco and from the city of Florencia were also collected. Analyses performed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) revealed that most of the target analytes were present in all the wastewater samples. The highest concentrations (up to 50 μg/L) corresponded to acetaminophen, but several antibiotics, such as azithromycin, ciprofloxacin and norfloxacin, and antihypertensive drugs, such as losartan and valsartan, were commonly present in influent wastewater (IWW) at levels above 1 μg/L. Moreover, the treatment applied in WWTPs seemed to not efficiently remove the compounds under study, because most pharmaceuticals were also present in effluent wastewater (EWW) at concentrations close to those of the IWW. Special emphasis was made in this work on the quality of data reported, performing a detailed study of quality control (QC) samples. The analytical approach used -direct injection of 5-fold diluted samples without any additional treatment - is simpler and faster than the commonly applied solid phase extraction (SPE). The use of 12 isotope-labelled internal standards ensured the satisfactory correction of matrix effects for the corresponding analytes. For the remaining 8 compounds, no drastic matrix effects were observed, and only four compounds (cloxacillin, doxycycline, losartan, tetracycline) presented QC recoveries near or slightly below 60%, revealing ionization suppression, particularly in the IWW. Data on the occurrence of pharmaceuticals reported in this paper are the basis for current studies that aim to develop efficient systems for the degradation/removal of these compounds from the aquatic environment.

Estimation of illicit drug use in the main cities of Colombia by means of urban wastewater analysis

Wastewater-based epidemiology (WBE) relies on the principle that traces of compounds, which a population is exposed to or consume, are excreted unchanged or as metabolites in urine and/or feces, and ultimately end up in the sewer network. Measuring target metabolic residues i.e. biomarkers in raw urban wastewater allows identifying the exposure or use of substances of interest in a community. Up to date, the most popular application of WBE is the estimation of illicit drug use and studies have been made mainly across Europe, which has allowed estimating and comparing drug use in many European cities. However, until now a comprehensive study applying WBE on the most frequently consumed illicit drugs has not been performed in South American countries. In this work, we applied this approach to samples from Colombia, selecting two of the most populated cities: Bogotá and Medellin. Several biomarkers were selected to estimate drug use of cocaine, cannabis, amphetamine, methamphetamine, MDMA (ecstasy), heroin and ketamine. Composite samples (24-h) were collected at the corresponding municipal wastewater treatment plants. Sample treatment was performed at location by applying solid-phase extraction (SPE). Before SPE, the samples were spiked with appropriate isotope labeled internal standards. In parallel, samples (spiked with the analytes under study at two concentration levels) were also processed for quality control. Analysis of influent wastewater was made by liquid chromatography-tandem mass spectrometry, with triple quadrupole analyzer. Data shown in this paper reveal a high use of cocaine by the population of the selected Colombian cities, particularly from Medellin, while the use of other illicit drugs were low. The relevance of using quality control samples, particularly in collaborative studies, as those presented in this work, where research groups from different countries participate and where the samples had to be shipped overseas, is highlighted in this paper.

Assessing geographical differences in illicit drug consumption--A comparison of results from epidemiological and wastewater data in Germany and Switzerland

BACKGROUND

Wastewater analysis is an innovative approach that allows monitoring illicit drug use at the community level. This study focused on investigating geographical differences in drug consumption by comparing epidemiological, crime and wastewater data.

METHODS

Wastewater samples were collected in 19 cities across Germany and Switzerland during one week, covering a population of approximately 8.1 million people. Self-report data and consumption offences for the investigated areas were used for comparison and to investigate differences between the indicators.

RESULTS

Good agreement between data sources was observed for cannabis and amphetamine-type stimulants, whereas substantial discrepancies were observed for cocaine. In Germany, an important distinction could be made between Berlin, Dortmund and Munich, where cocaine and particularly amphetamine were more prevalent, and Dresden, where methamphetamine consumption was clearly predominant. Cocaine consumption was relatively homogenous in the larger urban areas of Switzerland, although prevalence and offences data suggested a more heterogeneous picture. Conversely, marked regional differences in amphetamine and methamphetamine consumption could be highlighted.

CONCLUSIONS

Combining the available data allowed for a better understanding of the geographical differences regarding prevalence, typology and amounts of substances consumed. For cannabis and amphetamine-type stimulants, the complementarity of survey, police and wastewater data could be highlighted, although notable differences could be identified when considering more stigmatised drugs (i.e. cocaine and heroin). Understanding illicit drug consumption at the national scale remains a difficult task, yet this research illustrates the added value of combining complementary data sources to obtain a more comprehensive and accurate picture of the situation.

Direct liquid chromatography-tandem mass spectrometry determination of underivatized glyphosate in rice, maize and soybean

The residue determination of the widely used herbicide glyphosate (GLY) is highly problematic due to its amphoteric character, low mass and lack of chemical groups that might facilitate its detection. Most methods developed up to now have employed pre-column or post-column derivatization to form fluorescent derivatives and/or to reduce the polar character of the analyte facilitating its chromatographic retention. The aim of this work is to evaluate the feasibility of performing the direct LC-MS/MS determination of GLY residues in vegetables. After testing several Hydrophilic Interaction Liquid Chromatography (HILIC) columns, Obelisc N was selected due to its better chromatographic retention. LC-MS/MS determination has been performed in negative ionization mode, monitoring up to four transitions to give high reliability to the identification/confirmation process. This approach has been evaluated for the determination of GLY residues in rice, maize and soybean samples, and the method validated at different concentrations in compliance with the maximum residue limits established in the current legislation. After sample extraction with water, a combination of extract dilution, partition with dichloromethane, and solid phase extraction (SPE) using Oasis HLB cartridges (depending on the sample matrix under analysis) was applied. Quantification was made by using isotope-labeled GLY as internal standard and calibration in solvent. The methodology developed allows the rapid determination of GLY residues avoiding the derivatization step typically applied for this herbicide. The most critical issue is the robustness of the Obelisc N column, which was found to suffer rapid degradation with time. Extreme care and continuous testing of retention times and peak shapes is required for a reliable determination.

Improvements in the analytical methodology for the residue determination of the herbicide glyphosate in soils by liquid chromatography coupled to mass spectrometry

The determination of glyphosate (GLY) in soils is of great interest due to the widespread use of this herbicide and the need of assessing its impact on the soil/water environment. However, its residue determination is very problematic especially in soils with high organic matter content, where strong interferences are normally observed, and because of the particular physico-chemical characteristics of this polar/ionic herbicide. In the present work, we have improved previous LC-MS/MS analytical methodology reported for GLY and its main metabolite AMPA in order to be applied to "difficult" soils, like those commonly found in South-America, where this herbicide is extensively used in large areas devoted to soya or maize, among other crops. The method is based on derivatization with FMOC followed by LC-MS/MS analysis, using triple quadrupole. After extraction with potassium hydroxide, a combination of extract dilution, adjustment to appropriate pH, and solid phase extraction (SPE) clean-up was applied to minimize the strong interferences observed. Despite the clean-up performed, the use of isotope labelled glyphosate as internal standard (ILIS) was necessary for the correction of matrix effects and to compensate for any error occurring during sample processing. The analytical methodology was satisfactorily validated in four soils from Colombia and Argentina fortified at 0.5 and 5mg/kg. In contrast to most LC-MS/MS methods, where the acquisition of two transitions is recommended, monitoring all available transitions was required for confirmation of positive samples, as some of them were interfered by unknown soil components. This was observed not only for GLY and AMPA but also for the ILIS. Analysis by QTOF MS was useful to confirm the presence of interferent compounds that shared the same nominal mass of analytes as well as some of their main product ions. Therefore, the selection of specific transitions was crucial to avoid interferences. The methodology developed was applied to the analysis of 26 soils from different areas of Colombia and Argentina, and the method robustness was demonstrated by analysis of quality control samples along 4 months.

Use of time-of-flight mass spectrometry for large screening of organic pollutants in surface waters and soils from a rice production area in Colombia

The irrigate district of Usosaldaña, an important agricultural area in Colombia mainly devoted to rice crop production, is subjected to an intensive use of pesticides. Monitoring these compounds is necessary to know the impact of phytosanitary products in the different environmental compartments. In this work, surface water and soil samples from different sites of this area have been analyzed by applying an analytical methodology for large screening based on the use of time-of-flight mass spectrometry (TOF MS) hyphenated to liquid chromatography (LC) and gas chromatography (GC). Several pesticides were detected and unequivocally identified, such as the herbicides atrazine, diuron or clomazone. Some of their main metabolites and/or transformation products (TPs) like deethylatrazine (DEA), deisopropylatrazine (DIA) and 3,4-dichloroaniline were also identified in the samples. Among fungicides, carbendazim, azoxystrobin, propiconazole and epoxiconazole were the most frequently detected. Insecticides such as thiacloprid, or p,p'-DDT metabolites (p,p'-DDD and p,p'-DDE) were also found. Thanks to the accurate-mass full-spectrum acquisition in TOF MS it was feasible to widen the number of compounds to be investigated to other families of contaminants. This allowed the detection of emerging contaminants, such as the antioxidant 3,5-di-tertbutyl-4-hydroxy-toluene (BHT), its metabolite 3,5-di-tert-butyl-4-hydroxy-benzaldehyde (BHT-CHO), or the solar filter benzophenone, among others.