All-fiber few-mode interference for complex azimuthal pattern generation

We report on an all-fiber setup capable of generating complex intensity patterns using interference of few guided modes. Comprised by a few-mode fiber (FMF) spliced to a multimodal interference (MMI) fiber device, the setup allows for obtaining different output patterns upon adjusting the phases and intensities of the modes propagating in the FMF. We analyze the output patterns obtained when exciting two family modes in the MMI device using different phase and intensity conditions for the FMF modal base. Using this simple experimental arrangement we are able to produce complex intensity patterns with radial and azimuthal symmetry. Moreover, our results suggest that this approach provides a means to generate beams with orbital angular momentum (OAM).

Highly Coupled Seven-Core Fiber for Ratiometric Anti-Phase Sensing

A ratiometric fiber optic temperature sensor based on a highly coupled seven-core fiber (SCF) is proposed and experimentally demonstrated. A theoretical analysis of the SCF's sinusoidal spectral response in transmission configuration is presented. The proposed sensor comprises two SCF devices exhibiting anti-phase transmission spectra. Simple fabrication of the devices is shown by just splicing a segment of a 2 cm long SCF between two single-mode fibers (SMFs). The sensor proved to be robust against light source fluctuations, as a standard deviation of 0.2% was registered in the ratiometric measurements when the light source varied by 12%. Its low-cost detection system (two photodetectors) and the range of temperature detection (25 °C to 400 °C) make it a very attractive and promising device for real industrial applications.

Ratiometric Temperature Sensing Using Highly Coupled Seven-Core Fibers

In this paper, a ratiometric approach to sensing temperature variations is shown using specialty fiber optic devices. We analyzed the transmission response of cascaded segments of multicore fibers (MCFs), and dissimilar lengths were found to generate an adequate scheme for ratiometric operation. The perturbation of optical parameters in the MCFs translates to a rich spectral behavior in which some peaks increase their intensity while others decrease their intensity. Thus, by selecting opposite-behavior peaks, highly sensitive ratiometric measurements that provide robustness against spurious fluctuations can be performed. We implemented this approach using seven-core fiber (SCF) segments of 5.8 cm and 9.9 cm. To test the system's response under controlled perturbations, we heated one of the segments from ambient temperature up to 150 °C. We observed defined peaks with opposite behavior as a function of temperature. Two pairs of peaks within the interrogation window were selected to perform ratiometric calculations. Ratiometric measurements exhibited sensitivities 6-14 times higher than single-wavelength measurements. A similar trend with enhanced sensitivity in both peak pairs was obtained. In contrast to conventional interferometric schemes, the proposed approach does not require expensive facilities or micrometric-resolution equipment. Moreover, our approach has the potential to be realized using commercial splicers, detectors, and filters.

In-Line Mach-Zehnder Interferometers Based on a Capillary Hollow-Core Fiber Using Vernier Effect for a Highly Sensitive Temperature Sensor

In this paper, we propose a highly sensitive temperature sensor based on two cascaded Mach-Zehnder interferometers (MZIs) that work using the Vernier effect. The all-fiber MZIs were assembled by splicing a segment of capillary hollow-core fiber (CHCF) between two sections of multimode fibers (MMFs). This cascaded configuration exhibits a temperature sensitivity of 1.964 nm/°C in a range from 10 to 70 °C, which is ~67.03 times higher than the sensitivity of the single MZI. Moreover, this device exhibits a high-temperature resolution of 0.0153 °C. A numerical analysis was carried out to estimate the devices' temperature sensitivity and calculate the magnification of the sensitivity produced by the Vernier effect. The numerical results have an excellent agreement with the experimental results and provide a better insight into the working principle of the MZI devices. The sensor's performance, small size, and easy fabrication make us believe that it is an attractive candidate for temperature measurement in biological applications.

A high-throughput multiplexed microfluidic device for COVID-19 serology assays

The applications of serology tests to the virus SARS-CoV-2 are diverse, ranging from diagnosing COVID-19, understanding the humoral response to this disease, and estimating its prevalence in a population, to modeling the course of the pandemic. COVID-19 serology assays will significantly benefit from sensitive and reliable technologies that can process dozens of samples in parallel, thus reducing costs and time; however, they will also benefit from biosensors that can assess antibody reactivities to multiple SARS-CoV-2 antigens. Here, we report a high-throughput microfluidic device that can assess antibody reactivities against four SARS-CoV-2 antigens from up to 50 serum samples in parallel. This semi-automatic platform measures IgG and IgM levels against four SARS-CoV-2 proteins: the spike protein (S), the S1 subunit (S1), the receptor-binding domain (RBD), and the nucleocapsid (N). After assay optimization, we evaluated sera from infected individuals with COVID-19 and a cohort of archival samples from 2018. The assay achieved a sensitivity of 95% and a specificity of 91%. Nonetheless, both parameters increased to 100% when evaluating sera from individuals in the third week after symptom onset. To further assess our platform's utility, we monitored the antibody titers from 5 COVID-19 patients over a time course of several weeks. Our platform can aid in global efforts to control and understand COVID-19.

All-Fiber Measurement of Surface Tension Using a Two-Hole Fiber

An all-fiber approach is presented to measure surface tension. The experimental realization relies on the use of a specialty fiber, a so-called two-hole fiber (THF), which serves a two-fold purpose: providing a capillary channel to produce bubbles while having the means to measure the power reflected at the end facet of the fiber core. We demonstrate that provided a controlled injection of gas into the hollow channels of the THF, surface tension measurements are possible by simply tracking the Fresnel reflection at the distal end of the THF. Our results show that the characteristic times involved in the bubble formation process, from where the surface tension of the liquids under test is retrieved, can be measured from the train of pulses generated by the continuous formation and detachment of bubbles.

Linear multimode interference fiber temperature sensor using the liquid in glass thermometer principle

A temperature sensor based on a multimode interference thermometer is designed and fabricated. The operation mechanism is based on the thermal expansion of a specific volume of ethylene glycol contained in a glass bulb that is connected to a capillary of the same material, with a no-core fiber (NCF) inserted and centered into the capillary tube. As the temperature is increased, the liquid is expanded, and the NCF is gradually covered by the liquid, resulting in a peak wavelength shift that is correlated to the temperature variations. A sensitivity of 0.4447 nm/°C and highly linear response with an R² of 0.99962 are obtained. The advantage of this configuration is that the sensing temperature range can be adjusted by changing either the inner diameter of the capillary tube or the bulb volume. We can also measure negative temperatures by simply modifying the freezing point of the liquid, which demonstrates the viability of the sensor for many applications.

Optical improvement for modulating a high flux solar simulator designed for solar thermal and thermochemical research

This study presents the optical improvement of a high flux solar simulator (HFSS) with controllable flux-spot capabilities developed for researching solar thermal and thermochemical processes. The HFSS is comprised of seven 2.5  kW_el Xenon arc lamps coupled with ellipsoidal reflectors, a servo-controlled attenuator curtain, and three-axes linear test bench. Different attenuators were designed and tested in order to identify the best curtain geometry to improve the HFSS modulation with the lowest possible radiative losses. The optical design improvement was performed with the aid of TracePro, a Monte Carlo ray-tracing software. From simulation results, radiative peak flux from 1700 to 480  kWm^-2 from the focal plane to 300 mm further back was estimated without curtains. By using the attenuators, flux levels from 1570 to 92  kWm^-2 at the focal plane were also estimated. An experimental validation was achieved with a single lamp-reflector unit obtaining peak flux distributions from 200±20  kWm^-2 to 97±9.7  kWm^-2 from the focal plane to 300 mm behind. Flux modulation from 170 to 1.5  kWm^-2 was also measured at the focal plane using a servo-controlled curtain from fully-open slats (0°) to partially closed (60°). With this attenuator, introduced as the shutter of the system, the use of several lamps or electronic rectifiers is avoided and the radiative flux is modulated with high resolution in an optomechatronical form.

Suspended LRSPP for the development of highly integrated active plasmonic devices

We present a novel long-range surface plasmon polariton (LRSPP) device consisting of a suspended dielectric matrix in which an electrically active, millimeter-long metallic waveguide is embedded. We show that, by opening an air gap under the lower cladding, the influence of the substrate is suppressed and the symmetry of the thermo-optical distribution around the LRSPP waveguide is preserved over extended ranges of applied electrical current with minimal optical losses. Experimental results show that, compared to a standard nonsuspended structure, our device allows either the induction of a phase change that is three times larger, for a fixed electrical power, or, equivalently, a scaling down of the device to one-tenth of its original length, for a fixed phase change.

Stress homogenization effect in multicore fiber optic bending sensors

In this work we study the particular case of an optical fiber subjected to compression-bending load, the most common loading configuration for testing fiber optic bending sensors. Our analysis is based on the foundations of column theory and reveals a progressive stress homogenization across the optical fiber with increasing bending. This effect is general to any optical fiber subjected to this load configuration and it is of particular interest for structures with multiple cores since the state of stress experienced by each core can significantly differ even for a condition of constant load. The approach outlined here captures relevant features observed in experiments with multicore fiber optic bending sensors. Also, this approach can be incorporated into coupled-mode theory for assessing the performance of spectrally operated fiber sensors based on multicore coupled structures under realistic conditions commonly encountered in the experiments and without the need of performing computationally expensive simulations. The progressive stress homogenization, as well as the regime of homogeneous stress dominated by the bending contribution, is experimentally demonstrated using a multicore optical fiber with three coupled cores. Our observations are similar to those reported in recent experiments using other multicore fibers with different number of cores.

Passive athermalization of multimode interference devices for wavelength-locking applications

In this paper we demonstrate the passive, material-based athermalization of all-fiber architectures by cascading multimode interference (MMI) devices. In-line thermal compensation is achieved by including a liquid-core multimode section of variable length that allows ensuring temperature-independent operation while preserving the inherent filter-like spectral response of the MMI devices. The design of the temperature compensation unit is straightforward and its fabrication is simple. The applicability of our approach is experimentally verified by fabricating a wavelength-locked MMI laser with sensitivity of only -0.1 pm/°C, which is at least one order of magnitude lower than that achieved with other fiber optics devices.

Highly Sensitive Liquid Core Temperature Sensor Based on Multimode Interference Effects

A novel fiber optic temperature sensor based on a liquid-core multimode interference device is demonstrated. The advantage of such structure is that the thermo-optic coefficient (TOC) of the liquid is at least one order of magnitude larger than that of silica and this, combined with the fact that the TOC of silica and the liquid have opposite signs, provides a liquid-core multimode fiber (MMF) highly sensitive to temperature. Since the refractive index of the liquid can be easily modified, this allows us to control the modal properties of the liquid-core MMF at will and the sensor sensitivity can be easily tuned by selecting the refractive index of the liquid in the core of the device. The maximum sensitivity measured in our experiments is 20 nm/°C in the low-temperature regime up to 60 °C. To the best of our knowledge, to date, this is the largest sensitivity reported for fiber-based MMI temperature sensors.

A fiber optic ammonia sensor using a universal pH indicator

A universal pH indicator is used to fabricate a fiber optic ammonia sensor. The advantage of this pH indicator is that it exhibits sensitivity to ammonia over a broad wavelength range. This provides a differential response, with a valley around 500 nm and a peak around 650 nm, which allows us to perform ratiometric measurements. The ratiometric measurements provide not only an enhanced signal, but can also eliminate any external disturbance due to humidity or temperature fluctuations. In addition, the indicator is embedded in a hydrophobic and gas permeable polyurethane film named Tecoflex^®. The film provides additional advantages to the sensor, such as operation in dry environments, efficient transport of the element to be measured to the sensitive area of the sensor, and prevent leakage or detachment of the indicator. The combination of the universal pH indicator and Tecoflex^® film provides a reliable and robust fiber optic ammonia sensor.

In-fiber directional coupler for high-sensitivity curvature measurement

A curvature fiber optic sensor using a two-core fiber (TCF) is proposed and demonstrated. The TCF is designed to operate as a directional coupler with one core located exactly at the center of the fiber and the other off-axis, but close to the center of the fiber. This design allows straightforward splicing of the TCF to single mode fibers (SMF), and alignment of the off-axis core is not strictly required for optimum operation. The sensor is fabricated by simply splicing a 5 cm long section of TCF between two SMF sections, which provides a sinusoidal spectral response. When the fiber is bent, the coupling parameters are modified due to stress-optic and effective length effects, effectively blue-shifting the sinusoidal spectral response of the sensor and allowing for the measurement of curvature. The sensor exhibits linear response and a sensitivity of -137.87 nm/m(-1) for curvature ranging from 0 to 0.27 m(-1), making it suitable to measure small curvatures with high sensitivity.

Fiber-optic sensor for liquid level measurement

A novel (to the best of our knowledge) liquid level sensor based on multimode interference (MMI) effects is proposed and demonstrated. By using a multimode fiber (MMF) without cladding, known as no-core fiber, liquids around the MMF modify the self-imaging properties of the MMI device and the liquid level can be detected. We show that the sensor exhibits a highly linear response with the sensing range and multiplexed operations easily controlled by just modifying the length of the no-core fiber. At the same time, we can measure the refractive index of the liquid based on the maximum peak wavelength shift. We can also use the sensor for continuous and discrete liquid level sensing applications, thus providing a liquid level sensor that is inexpensive with a very simple fabrication process.

Mode-locked fiber laser using an SU8/SWCNT saturable absorber

We report the fabrication of a saturable absorber based on SU8 single wall carbon nanotube (SWCNT) composite material. Thin films with a controllable thickness can be fabricated using a simple and reliable process. These films can be inserted between two FC/APC connectors in order to have an inline saturable absorber. A passive mode-locked laser was built by interleaving the fiberized saturable absorber in an erbium-doped fiber (L-band) ring cavity laser. The laser produces 871 fs pulses with a repetition rate of 21.27 MHz and a maximum average power of 1 mW.

Tunable multimode-interference bandpass fiber filter

We report on a wavelength-tunable filter based on multimode interference (MMI) effects. A typical MMI filter consists of a multimode fiber (MMF) spliced between two single-mode fibers (SMF). The peak wavelength response of the filter exhibits a linear dependence when the length of the MMF is modified. Therefore a capillary tube filled with refractive-index-matching liquid is used to effectively increase the length of the MMF, and thus wavelength tuning is achieved. Using this filter a ring-based tunable erbium-doped fiber laser is demonstrated with a tunability of 30 nm, covering the full C-band.

Widely tunable erbium-doped fiber laser based on multimode interference effect

A widely tunable erbium-doped all-fiber laser has been demonstrated. The tunable mechanism is based on a novel tunable filter using multimode interference effects (MMI). The tunable MMI filter was applied to fabricate a tunable erbium-doped fiber laser via a standard ring cavity. A tuning range of 60 nm was obtained, ranging from 1549 nm to 1609 nm, with a signal to noise ratio of 40 dB. The tunable MMI filter mechanism is very simple and inexpensive, but also quite efficient as a wavelength tunable filter.

Discrete Talbot effect in waveguide arrays

We report the first observation of discrete Talbot revivals in one-dimensional waveguide arrays. Unlike continuous systems where the Talbot self-imaging effect always occurs irrespective of the pattern period, in discrete configurations this process is only possible for a specific set of periodicities. Recurrence of different input periodic patterns is observed in good agreement with theory.