Bismuth ferrite based acetone gas sensor: evaluation of graphene oxide loading

We report a BiFeO3/graphene oxide (BFO/GO) perovskite, synthesized using a CTAB-functionalized glycine combustion route, as a potential material for acetone gas sensing applications. The physicochemical properties of the developed perovskite were analysed using XRD, FE-SEM, TEM, HRTEM, EDAX and XPS. The gas sensing performance was analysed for various test gases, including ethanol, acetone, propanol, ammonia, nitric acid, hydrogen sulphide and trimethylamine at a concentration of 500 ppm. Among the test gases, the developed BFO showed the best selectivity towards acetone, with a response of 61% at an operating temperature of 250 °C. All the GO-loaded BFO samples showed an improved gas sensing performance compared with pristine BFO in terms of sensitivity, the response/recovery times, the transient response curves and the stability. The 1 wt% GO-loaded BiFeO3 sensor showed the highest sensitivity of 89% towards acetone (500 ppm) at an operating temperature of 250 °C. These results show that the developed perovskites have significant potential for use in acetone gas sensing applications.

Evaluation of Structural, Magnetic, and Electromagnetic Properties of Co2+-Substituted NiCuZn Ferrites

We report citrate gel-assisted autocombusted spinel-type Co2+-substituted NiCuZn ferrites and their electromagnetic properties. Several complementary techniques were used to investigate the influence of Co on structural and electromagnetic properties of Ni0.25-xCoxCu0.20Zn0.55Fe2O4 with x = 0.00-0.25 (step of 0.05). XRD analysis confirmed the highly crystalline single-phase cubic spinel structure with a prominent peak of the (311) plane. FE-SEM analysis showed the loss of porous gel structure (colloidal backbone) due to addition of cobalt into the present ferrite system. The EDAX analysis confirmed the presence of Ni, Cu, Zn, Co, and O in accordance with the relative stoichiometry of Co-substituted NiCuZn ferrite. The electrical resistivity of ferrites is observed to decrease when Co2+ ions are substituted, regardless of AC and DC. The dielectric properties (ε' and ε″) of ferrites exhibited a consistent decrease as the frequency increased, and this trend persisted even at higher frequencies. VSM analysis showed the normal magnetic hysteresis of the developed ferrite system. At x = 0.05, the saturation magnetization of the ferrite was obtained to be the highest among the other substitution levels of Co. The Curie temperature fell down when there was a higher concentration of cobalt in the ferrite system (x = 0.20). After reaching a specific temperature, the μi values decreased abruptly, with an increase in the temperature. The steady state may be deduced from the fact that the constant real component of the initial permeability, μ', remained unchanged. However, with decreasing frequency, the values of μ″ decreased dramatically. The present NiCuZn ferrite series displays the enhanced dielectric properties suggesting the capability of potential candidates for microwave absorption applications with enhanced electromagnetic properties.

Ionic-Liquid-Assisted Synthesis of Mixed-Phase Manganese Oxide Nanorods for a High-Performance Aqueous Zinc-Ion Battery

Aqueous zinc-ion batteries (ZIBs) provide a safer and cost-effective energy storage solution by utilizing nonflammable water-based electrolytes. Although many research efforts are focused on optimizing zinc anode materials, developing suitable cathode materials is still challenging. In this study, one-dimensional, mixed-phase MnO₂ nanorods are synthesized using ionic liquid (IL). Here, the IL acts as a structure-directing agent that modifies MnO₂ morphology and introduces mixed phases, as confirmed by morphological, structural, and X-ray photoelectron spectroscopy (XPS) studies. The MnO₂ nanorods developed by this method are utilized as a cathode material for ZIB application in the coin-cell configuration. As expected, Zn//MnO₂ nanorods show a significant increase in their capacity to 347 Wh kg^-1 at 100 mA g^-1, which is better than bare MnO₂ nanowires (207.1 Wh kg^-1) synthesized by the chemical precipitation method. The battery is highly rechargeable and maintains good retention of 86% of the initial capacity and 99% Coulombic efficiency after 800 cycles at 1000 mA g^-1. The ex situ XPS, X-ray diffraction, and in-depth electrochemical analysis confirm that MnO₆ octahedra experience insertion/extraction of Zn²⁺ with high reversibility. This study suggests the potential use of MnO₂ nanorods to develop high-performance and durable battery electrode materials suitable for large-scale applications.

Magnetically recoverable sol-gel auto-combustion developed Ni1-xCuxDyyFe2-yO4 magnetic nanoparticles for photocatalytic, electrocatalytic, and antibacterial applications

Copper and dysprosium doped NiFe₂O₄ magnetic nanomaterials, Ni_1-xCu_xDy_yFe_2-yO₄ (x = y = 0.00, 0.01, 0.02, 0.03), was prepared by utilizing sol-gel auto-combustion approach to inspect the photodegradation of methylene blue (MB) pollutant and also, to perform the electrocatalytic water splitting and antibacterial studies. The XRD analysis reveal the growth of a single-phase spinel cubic structure for produced nanomaterials. The magnetic traits show an increasing trend in saturation magnetization (M_s) from 40.71 to 47.90 emu/g along with a decreasing behaviour of coercivity from 158.09 to 142.31 Oe at lower and higher Cu and Dy doping content (x = 0.0-0.01). The study of optical band gap values of copper and dysprosium-doped nickel nanomaterials decreased from 1.71 to 1.52 eV. This will increase the photocatalytic degradation of methylene blue pollutant from 88.57% to 93.67% under natural sunlight, respectively. These findings clearly show that under natural sunlight irradiation for 60 min, the produced N4 photocatalyst displays the greatest photocatalytic activity with a maximum removal percentage of 93.67%. The electrocatalytic characteristics of produced magnetic nanomaterials for both HER and OER were examined with a Calomel electrode taking as a reference in a 0.5 N H₂SO₄ and 0.1 N KOH electrolyte. The N4 electrode demonstrated considerable 10 and 0.024 mA/cm² of current density, with onset potentials of 0.99 and 1.5 V for HER and OER and also, have tafel slopes of 58.04 and 295 mV/dec, respectively. The antibacterial activity for produced magnetic nanomaterials was examined against various bacteria (Bacillus subtilis, Staphylococcus aureus, S. typhi, and P. aeruginosa) in which N3 sample produced significant inhibition zone against gram-positive bacteria (Bacillus subtilis and Staphylococcus aureus) but no zone of inhibition against gram-negative bacteria (S. typhi and P. aeruginosa). With all these superior traits, the produced magnetic nanomaterials are highly valuable for the wastewater remediation, hydrogen evolution, and biological applications.

A Novel Synthesized 1D Nanobelt-like Cobalt Phosphate Electrode Material for Excellent Supercapacitor Applications

In the present report, we synthesized highly porous 1D nanobelt-like cobalt phosphate (Co₂P₂O₇) materials using a hydrothermal method for supercapacitor (SC) applications. The physicochemical and electrochemical properties of the synthesized 1D nanobelt-like Co₂P₂O₇ were investigated using X-ray diffraction (XRD), X-ray photoelectron (XPS) spectroscopy, and scanning electron microscopy (SEM). The surface morphology results indicated that the deposition temperatures affected the growth of the 1D nanobelts. The SEM revealed a significant change in morphological results of Co₂P₂O₇ material prepared at 150 °C deposition temperature. The 1D Co₂P₂O₇ nanobelt-like nanostructures provided higher electrochemical properties, because the resulting empty space promotes faster ion transfer and improves cycling stability. Moreover, the electrochemical performance indicates that the 1D nanobelt-like Co₂P₂O₇ electrode deposited at 150 °C deposition temperature shows the maximum specific capacitance (Cs). The Co₂P₂O₇ electrode prepared at a deposition temperature 150 °C provided maximum Cs of 1766 F g^-1 at a lower scan rate of 5 mV s^-1 in a 1 M KOH electrolyte. In addition, an asymmetric hybrid Co₂P₂O₇//AC supercapacitor device exhibited the highest Cs of 266 F g^-1, with an excellent energy density of 83.16 Wh kg^-1, and a power density of 9.35 kW kg^-1. Additionally, cycling stability results indicate that the 1D nanobelt-like Co₂P₂O₇ material is a better option for the electrochemical energy storage application.

Polyaniline-wrapped MnMoO4 as an active catalyst for hydrogen production by electrochemical water splitting

Developing efficient, low-cost, and environment-friendly electrocatalysts for hydrogen generation is critical for lowering energy usage in electrochemical water splitting. Moreover, for commercialization, fabricating cost-efficient, earth-abundant electrocatalysts with superior characteristics is of urgent need. Towards this endeavor, we report the synthesis of PANI-MnMoO₄ nanocomposites using a hydrothermal approach and an in situ polymerization method with various concentrations of MnMoO₄. The fabricated nanocomposite electrocatalyst exhibits bifunctional electrocatalytic activity towards the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER) at a lower overpotential of 410 mV at 30 mA cm^-2 and 155 mV at 10 mA cm^-2, respectively in an alkaline electrolyte. Furthermore, while showing overall water splitting (OWS) performance, the optimized PM-10 (PANI-MnMoO₄) electrode reveals the most outstanding OWS performance with a lower cell voltage of 1.65 V (vs. RHE) at a current density of 50 mA cm^-2 with an excellent long-term cell resilience of 24 h.

RGO/WO3 hierarchical architectures for improved H2S sensing and highly efficient solar-driving photo-degradation of RhB dye

Surface area and surface active sites are two important key parameters in enhancing the gas sensing as well as photocatalytic properties of the parent material. With this motivation, herein, we report a facile synthesis of Reduced Graphene Oxide/Tungsten Oxide RGO/WO3 hierarchical nanostructures via simple hydrothermal route, and their validation in accomplishment of improved H2S sensing and highly efficient solar driven photo-degradation of RhB Dye. The self-made RGO using modified Hummer's method, is utilized to develop the RGO/WO3 nanocomposites with 0.15, 0.3 and 0.5 wt% of RGO in WO3 matrix. As-developed nanocomposites were analyzed using various physicochemical techniques such as XRD, FE-SEM, TEM/HRTEM, and EDAX. The creation of hierarchic marigold frameworks culminated in a well affiliated mesoporous system, offering efficient gas delivery networks, leading to a significant increase in sensing response to H2S. The optimized sensor (RGO/WO3 with 0.3 wt% loading) exhibited selective response towards H2S, which is ~ 13 times higher (Ra/Rg = 22.9) than pristine WO3 (Ra/Rg = 1.78) sensor. Looking at bi-directional application, graphene platform boosted the photocatalytic activity (94% degradation of Rhodamine B dye in 210 min) under natural sunlight. The RGO's role in increasing the active surface and surface area is clarified by the H2S gas response analysis and solar-driven photo-degradation of RhB dye solution. The outcome of this study provides the new insights to RGO/WO3 based nanocomposites' research spreadsheet, in view of multidisciplinary applications.

Microwave-Epoxide-Assisted Hydrothermal Synthesis of the CuO/ZnO Heterojunction: a Highly Versatile Route to Develop H2S Gas Sensors

A robust synthesis approach to develop CuO/ZnO nanocomposites using microwave-epoxide-assisted hydrothermal synthesis and their proficiency toward H2S gas-sensing application are reported. The low-cost metal salts (Cu and Zn) as precursors in aqueous media and epoxide (propylene oxide) as a proton scavenger/gelation agent are used for the formation of mixed metal hydroxides. The obtained sol was treated using the microwave hydrothermal process to yield the high-surface area (34.71 m2/g) CuO/ZnO nanocomposite. The developed nanocomposites (1.25-10 mol % Cu doping) showcase hexagonal ZnO and monoclinic CuO structures, with an average crystallite size in the range of 18-29 nm wrt Cu doping in the ZnO matrix. The optimized nanocomposite (2.5 mol % Cu doping) showed a lowest crystallite size of 21.64 nm, which reduced further to 18.06 nm upon graphene oxide addition. Morphological analyses (scanning electron microscopy and transmission electron microscopy) exhibited rounded grains along with copious channels typical for sol-gel-based materials . Elemental mapping displayed the good dispersion of Cu in the ZnO matrix. When these materials are employed as a gas sensor, they demonstrated high sensitivity and selectivity toward H2S gas in comparison with the reducing gases and volatile organic compounds under investigation. The systematic doping of Cu in the ZnO matrix exhibited an improved response from 76.66 to 94.28%, with reduction in operating temperature from 300 to 250 °C. The 2.5 mol % doped Cu in ZnO was found to impart a response of 23 s for 25 ppm of H2S. Gas-sensing properties are described using an interplay of epoxide-assisted sol-gel chemistry and structural and morphological properties of the developed material.

Bioinspired Carbon Quantum Dots: An Antibiofilm Agents

Carbon dots, very tiny carbon material with various surface passivations, have emerged as a new class of nanomaterials for various applications. Herein, we describe a simple, economical, and green approach for the synthesis of colloidal luminescent carbon dots (C-dots) by solvothermal method from fruit juice of Citrus limetta, an abundantly available plant in Asian countries. The existence of C-dots was confirmed by X-ray Diffraction and High Resolution Transmission Electron Microscopy studies. The C-dots size was observed to be 2-4 nm. We further evaluated the efficacy of C-dots to inhibit the attachment of Candida albicans MTCC 227, and biofilm formation on the polystyrene surfaces. The C-dots have effectively inhibited the attachment and formation of biofilm in Candida albicans at very low concentrations, which is hitherto unattempted. The ability of C-dots to inhibit biofilm formation may contribute to diverse applications of C-dots in biomedical field.

A greener approach towards the development of graphene–Ag loaded ZnO nanocomposites for acetone sensing applications

We report a facile, green synthesis of graphene/Ag/ZnO nanocomposites and their use as acetone sensors via a medicinal plant extraction assisted precipitation process. The choice of plant extract in combination with metal nitrates led to self-sustaining colloid chemistry. Along with the green synthesis strategy, structural, morphological and gas sensing properties are described.

We report a facile, green synthesis of graphene/Ag/ZnO nanocomposites and their use as acetone sensors via a medicinal plant extraction assisted precipitation process.

Ru-Loaded mesoporous WO3 microflowers for dual applications: enhanced H2S sensing and sunlight-driven photocatalysis

We report a facile synthesis of Ru-loaded WO3 marigold structures through a hydrothermal route and their bidirectional applications as enhanced H2S gas sensors and efficient sunlight-driven photocatalysts. The developed hierarchical marigold structures provide effective gas diffusion channels via a well-aligned mesoporous framework, resulting in remarkable enhancement in the sensing response to H2S. The temperature and gas concentration dependence on the sensing properties reveals that Ru loading not only improves the sensing response, but also lowers the operating temperature of the sensor from 275 to 200 °C. The 0.5 wt% Ru-loaded WO3 shows selective response towards H2S, which is 45 times higher (142) than that of pristine WO3 (3.16) sensor, whereas the 0.25 wt% Ru-loaded WO3 exhibits the highest photocatalytic activity, as shown by the degradation of rhodamine B (RhB) under natural sunlight. The gas sensing and photocatalytic properties are explained through the role of Ru and the structural and morphological properties of the developed material.

Growth study of hierarchical Ag3PO4/LaCO3OH heterostructures and their efficient photocatalytic activity for RhB degradation

We demonstrate a simple, cost effective co-precipitation method to synthesize APO/LCO heterostructures and investigate the effect of a mixed solvent system (H₂O:THF) on the growth of microstructures.

Fern-like rGO/BiVO4 Hybrid Nanostructures for High-Energy Symmetric Supercapacitor

Herein, we demonstrate the synthesis of rGO/BiVO₄ hybrid nanostructures by facile hydrothermal method. Morphological studies reveal that rGO sheets are embedded in the special dendritic fern-like structures of BiVO₄. The rGO/BiVO₄ hybrid architecture shows the way to a rational design of supercapacitor, since these structures enable easy access of electrolyte ions by reducing internal resistance. Considering the unique morphological features of rGO/BiVO₄ hybrid nanostructures, their supercapacitive properties were investigated. The rGO/BiVO₄ electrode exhibits a specific capacitance of 151 F/g at the current density of 0.15 mA/cm². Furthermore, we have constructed rGO/BiVO₄ symmetric cell which exhibits outstanding volumetric energy density of 1.6 mW h/cm³ (33.7 W h/kg) and ensures rapid energy delivery with power density of 391 mW/cm³ (8.0 kW/kg). The superior properties of symmetric supercapacitor can be attributed to the special dendritic fern-like BiVO₄ morphology and intriguing physicochemical properties of rGO.

Self-assembled hierarchical nanostructures of Bi2WO6 for hydrogen production and dye degradation under solar light

Photocatalytic dye degradation and H₂ generation are demonstrated using 3D hierarchical nanostructures of orthorhombic Bi₂WO₆ synthesized by a solvothermal method.

Magnetically separable Ag3PO4/NiFe2O4 composites with enhanced photocatalytic activity

A step wise growth process of APO nuclei leads to developing interesting morphologies of APO/NFO composites.

Polymethyl methacrylate (PMMA)–bismuth ferrite (BFO) nanocomposite: low loss and high dielectric constant materials with perceptible magnetic properties

Formation mechanism of PMMA–BFO nanocomposites.

Nanowires of silver-polyaniline nanocomposite synthesized via in situ polymerization and its novel functionality as an antibacterial agent

Silver-polyaniline (Ag-PANI) nanocomposite was synthesized by in situ polymerization method using ammonium persulfate (APS) as an oxidizing agent in the presence of dodecylbenzene sulfonic acid (DBSA) and silver nitrate (AgNO(3)). The as synthesized Ag-PANI nanocomposite was characterized by using different analytical techniques such as UV-visible (UV-vis) and Fourier transform Infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FE-SEM), thermo gravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscopy (TEM). UV-visible spectra of the synthesized nanocomposite showed a sharp peak at ~420 nm corresponding to the surface plasmon resonance (SPR) of the silver nanoparticles (AgNPs) embedded in the polymer matrix which is overlapped by the polaronic peak of polyaniline appearing at that wavelength. Nanowires of Ag-PANI nanocomposite with diameter 50-70 nm were observed in FE-SEM and TEM. TGA has indicated an enhanced thermal stability of nanocomposite as compared to that of pure polymer. The Ag-PANI nanocomposite has shown an antibacterial activity against model organisms, a gram positive Bacillus subtilis NCIM 6633 in Mueller-Hinton (MH) medium, which is hitherto unattempted. The Ag-PANI nanocomposite with monodispersed AgNPs is considered to have potential applications in sensors, catalysis, batteries and electronic devices.