The match between adhesive mixture powder formulations for inhalation and the inhaler device

The device or the formulation? Which one governs drug dispersibility from the inhaler? To address this question, three budesonide-containing reservoir DPIs: Novopulmon Novolizer®, Giona Easyhaler® and DuoResp Spiromax®, were analyzed using the Next Generation Impactor, NGI. Thereafter, the devices were carefully opened, emptied, and formulations were switched between devices. Finally, three 'prototype' formulations with carriers of different particle size were produced and tested in the Novolizer and Easyhaler devices. Among the DPI products, the two devices which have a flow path with a cyclone-type geometry, i.e., the Novolizer and the Spiromax, yielded a fine particle fraction, FPF, above 40%. The Easyhaler, which has a straight mouthpiece outlet, produced an FPF of 18 %. When the Novopulmon and the DuoResp formulations were assayed in the Easyhaler device, poor fine particle fractions were obtained. To the contrary, the Giona formulation produced a high FPF when tested in the Novolizer device. The results clearly show that the device is the dominating factor to dispersibility for the investigated products. Along the same lines, all three 'prototype' formulations produced high fine particle fractions in the Novolizer device, with the formulation with the largest carrier giving the best performance. Tested in the Easyhaler device, the prototype formulations produced low fine particle fractions, but interestingly, the formulation with the smallest carrier particle size yielded the highest FPF. It can be concluded that there is a link between inhaler design and the effect of carrier particle size, where larger carriers provide better dispersion in cyclone-type devices while smaller carriers seem to be more beneficial for inhalers which has a straight flow path for the powder formulation.

Increasing the fine particle fraction of pressurised metered dose inhaler solutions with novel actuator shapes

In this paper we demonstrate that the use of multiple orifices can improve the fine particle fraction (FPF) of pressurised metered-dose inhaler solution formulations by up to 75% when compared to a single orifice with an equivalent cross sectional area (p<0.05). While prior work has relied on metal actuator components, improvements in micro injection moulding and micro drilling now make it possible to mass produce novel orifice shapes to achieve similar FPF gains in plastic parts, with orifice diameters less than 0.2 mm. The ability to create internal features inside the actuator is also demonstrated. We show through in vitro high speed imaging that twin orifice sprays merge quickly and act as a single, modified plume. We also show for the first time that FPF and fine particle dose (FPD) are strongly correlated with the distance at which the plume velocity decays to half its initial value (R²=0.997 and 0.95 respectively). When plume velocity & FPF are increased, mouthpiece deposition decreases. This suggests that while smaller orifices produce more fine particles, higher sustained plume velocities also entrain more of the fine particles produced at the periphery of the spray due to increased shear. The effect occurs within the mouthpiece and is thus unlikely to alter the flow field in the upper airway.

Fabrication, characterization and optimization of nanostructured lipid carrier formulations using Beclomethasone dipropionate for pulmonary drug delivery via medical nebulizers

Aerosolization is a non-invasive approach in drug delivery for localized and systemic effect. Nanostructured lipid carriers (NLCs) are new generation versatile carriers, which offer protection from degradation and enhance bioavailability of poorly water soluble drugs. The aim of this study was to develop and optimize NLC formulations in combination with optimized airflow rates (i.e. 60 and 15 L/min) and choice of medical nebulizers including Air jet, Vibrating mesh and Ultrasonic nebulizer for superior aerosolization performance, assessed via a next generation impactor (NGI). Novel composition and combination of NLC formulations (F1 - F15) were prepared via ultrasonication method, employing five solid lipids (glycerol trimyristate (GTM), glycerol trilaurate (GTL), cetyl palmitate (CP), glycerol monostearate (GMS) and stearic acid (SA)); and three liquid lipids (glyceryl tributyrate (GTB), propylene glycol dicaprylate/dicaprate (PGD) and isopropyl palmitate (IPP)) in 1:3 w/w ratios (i.e. combination of one solid and one liquid lipid), with Beclomethasone dipropionate (BDP) incorporated as the model drug. Out of fifteen BDP-NLC formulations, the physicochemical properties of formulations F7, F8 and F10 exhibited desirable stability (one week at 25 °C), with associated particle size of ~241 nm, and >91% of drug entrapment. Post aerosolization, F10 was observed to deposit notably smaller sized particles (from 198 to 136 nm, 283 to 135 nm and 239 to 157 nm for Air jet, Vibrating mesh and Ultrasonic nebulizers, respectively) in all stages (i.e. from stage 1 to 8) of the NGI, when compared to F7 and F8 formulations. Six week stability studies conducted at 4, 25 and 45 °C, demonstrated F10 formulation stability in terms of particle size, irrespective of temperature conditions. Nebulizer performance study using the NGI for F10 identified the Air jet to be the most efficient nebulizer, depositing lower concentrations of BDP in the earlier stages (1-3) and higher (circa 82 and 85%) in the lateral stages (4-8) using 60 and 15 L/min airflow rates, when compared to the Vibrating mesh and Ultrasonic nebulizers. Moreover, at both airflow rates, the Air jet nebulizer elicited a longer nebulization time of ~42 min, facilitating aerosol inhalation for prophylaxis of asthma with normal tidal breathing. Based on characterization and nebulizer performance employing both 60 and 15 L/min airflow rates, the Air jet nebulizer offered enhanced performance, exhibiting a higher fine particle dose (FPD) (90 and 69 µg), fine particle fraction (FPF) (70 and 54%), respirable fraction (RF) (92 and 69%), and lower mass median aerodynamic diameter (MMAD) (1.15 and 1.62 µm); in addition to demonstrating higher drug deposition in the lateral parts of the NGI, when compared to its counterpart nebulizers. The F10 formulation used with the Air jet nebulizer was identified as being the most suitable combination for delivery of BDP-NLC formulations.

Porous and highly dispersible voriconazole dry powders produced by spray freeze drying for pulmonary delivery with efficient lung deposition

Systemic administration of antifungal agents for the treatment of pulmonary aspergillosis is limited by the poor lung deposition and severe adverse effects. In contrast, pulmonary delivery allows a higher amount of drug to be delivered directly to the infection site and therefore a lower dose is required. This study aimed to develop porous and inhalable voriconazole dry powder with good lung deposition by spray freeze drying (SFD), using tert-butyl alcohol (TBA) as a co-solvent. A three-factor two-level full factorial design approach was used to investigate the effect of total solute concentration, drug content and co-solvent composition on the aerosol performance of the SFD powder. In general, the SFD voriconazole powder exhibited porous and spherical structure, and displayed crystalline characteristics. The analysis of factorial design indicated that voriconazole content was the most significant variable that could influence the aerosol performance of the SFD powders. The formulations that contained a high voriconazole content (40% w/w) and high TBA concentration in the feed solution (70% v/v) displayed the highest fine particle fraction of over 40% in the Next Generation Impactor study in which the powder was dispersed with a Breezhaler® at 100 L/min. In addition, the fine particle dose of the SFD powder showed a faster dissolution rate when compared to the unformulated voriconazole. Intratracheal administration of SFD voriconazole powder to mice resulted in a substantially higher drug concentration in the lungs when comparing to the group that received an equivalent dose of liquid voriconazole formulation intravenously, while a clinically relevant plasma drug concentration was maintained for at least two hours. Overall, an inhalable voriconazole dry powder formulation exhibiting good aerosol property and lung deposition was developed with clinical translation potential.

Using two-fluid nozzle for spray freeze drying to produce porous powder formulation of naked siRNA for inhalation

Spray freeze drying is an attractive technology to produce powder formulation for inhalation. It can be used to generate large porous particles which tend to aerosolize efficiently and do not aggregate readily. It also avoids material to be exposed to elevated temperature. In this study, we reported the use of two-fluid nozzle to produce spray freeze dried powder of small interfering RNA (siRNA). The effect of atomization gas flow rate and liquid feed rate were inspected initially using herring sperm DNA (hsDNA) as nucleic acid model. The atomization gas flow rate was found to have a major impact on the aerosol properties. The higher the atomization gas flow rate, the smaller the particle size, the higher the fine particle fraction (FPF). In contrast, the liquid feed rate had very minor effect. Subsequently, spray freeze dried siRNA powder was produced at various atomization gas flow rates. The particles produced were highly porous as examined with the scanning electron microscopy, and the structural integrity of the siRNA was demonstrated with gel electrophoresis. The gene-silencing effect of the siRNA was also successfully preserved in vitro. The best performing siRNA formulation was prepared at the highest atomization gas flow rate investigated with a moderate FPF of 30%. However, this was significantly lower than that obtained with the corresponding hsDNA counterparts (FPF ∼57%). A direct comparison between the hsDNA and siRNA formulations revealed that the former exhibited a lower density, hence a smaller aerodynamic diameter despite similar geometric size.

Development of ciprofloxacin-loaded poly(vinyl alcohol) dry powder formulations for lung delivery

Polymeric microparticles are micro carriers for the sustained drug delivery of drugs in the lungs, used as alternatives to the use of established excipients. This study aims to develop and characterize inhalable ciprofloxacin (CPx)-loaded poly(vinyl alcohol) (PVA) microparticles by a single-step spray-drying procedure. The optimization of the processing parameters was achieved by an orthogonal design of the most relevant processing parameters (polymer concentration, feed rate and inlet temperature). The obtained spray-dried particles showed a drug encapsulation efficiency higher than 90%. Furthermore, PVA-CPx formulations, with drug contents up to 10 wt%, showed a morphology and size suitable for inhalation, with a sustained release profile over 24 h. Data from Fourier transformed infra-red spectroscopy and differential scanning calorimetry indicated absence of interaction between the polymer matrix and the drug. Aerodynamic assessment of PVA-CPx 10 wt% was determined by the next generation impactor (NGI), using spray-dried CPx as a control. The results showed improved values of mass median aerodynamic diameter (5.06±0.10μm) and a fine particle fraction (39.78±0.98%) when comparing with the CPx alone (5.33±0.39μm and 30.43±1.38%). This study highlights the potential of spray-dried PVA microparticles as drug carriers for lung local delivery of antibiotics.

The effect of different coating materials on the prevention of powder bounce in the next generation impactor

In the process of quality control of pulmonary drug delivery products, aerosolization efficiency is mainly determined using impactors, e.g. next generation impactor (NGI). However, particle bounce may interfere with the validity and accuracy of results due to the overestimation of the respirable fraction. It is suggested that the coating of impactor's stages may prevent the particle bounce. Therefore, coating materials may influence the results of the aerosolization indexes of pulmonary dosage forms. The aim of this study was to investigate if the aerosolization indices are affected differently by using the different coating materials. In this study, the effects of using different materials including Span^® 85, Tween^® 80, silicon^® oil, glycerin and Brij^® 35/glycerin mixture recommended for the coating of NGI stages on the aerosolization indices such as fine particle fraction, fine particle dose, mass median aerodynamic diameter, and geometric standard deviation of salbutamol emitted from a commercial metered dose inhaler (MDI), were assessed. Three statistically different results were obtained on using Tween^® 80, Span^® 85 and silicon oil, and glycerin and Brij^®35/glycerin mixture. It can be concluded that the type of coating material influenced the aerosolization indices of the examined MDI in NGIs.

Development of an inhalable, stimuli-responsive particulate system for delivery to deep lung tissue

Lung cancer, the deadliest solid tumor among all types of cancer, remains difficult to treat. This is a result of unavoidable exposure to carcinogens, poor diagnosis, the lack of targeted drug delivery platforms and limitations associated with delivery of drug to deep lung tissues. Development of a non-invasive, patient-convenient formula for the targeted delivery of chemotherapeutics to cancer in deep lung tissue is the aim of this study. The formulation consisted of inhalable polyvinylpyrrolidone (PVP)/maltodextrin (MD)-based microparticles (MPs) encapsulating chitosan (CS) nanoparticles (NPs) loaded with either drug only or drug and magnetic nanoparticles (MNPs). Drug release from CS NPs was enhanced with the aid of MNPs by a factor of 1.7 in response to external magnetic field. Preferential toxicity by CS NPs was shown towards tumor cells (A549) in comparison to cultured fibroblasts (L929). The prepared spray freeze dried (SFD) powders for CS NPs and CS MNPs were of the same size at ∼6μm. They had a fine particle fraction (FPF≤5.2μm) of 40-42% w/w and mass median aerodynamic diameter (MMAD) of 5-6μm as determined by the Next Generation Impactor (NGI). SFD-MPs of CS MNPs possess higher MMAD due to the high density associated with encapsulated MNPs. The developed formulation demonstrates several capabilities including tissue targeting, controlled drug release, and the possible imaging and diagnostic values (due to its MNPs content) and therefore represents an improved therapeutic platform for drug delivery to cancer in deep lung tissue.