Risk Influence of Some Environmental and Behavioral Factors on Air Contamination in the Operating Room: An Experimental Study

Air contamination in operating rooms (ORs) depends on the conditions of the room and on activities therein performed. Methodologies of air quality assessment in ORs are often inadequately described in the scientific literature, and the time required for a change in status in air quality is never taken into account. The purpose of this study was to determine the influence of the state and the presence of human operators on air quality by implementing a precise measurement protocol that also took into account the time required for changes in the room to affect air pollution. As the main indicators of air pollution, bacterial load and concentration of airborne dust were measured. The results showed that: the use of surgical masks by operators in the OR did not significantly affect bacterial load within a distance of 2 m; keeping OR doors open did not induce a significant increase in bacterial load and of 5 μm particles while 10 μm particles concentration was positively affected; and air pollution measured with open doors was not significantly different from that due to the presence of two staff members, whether or not they were wearing masks. The results clarified the role of some factors on air pollution in ORs.

Changes in eating time, chewing activity and dust concentration in horses fed either alfalfa cubes or long-stem hay

BACKGROUND

Chewing is an essential physiological process in horses; yet, the physical form of feeds may affect their chewing and feeding behaviour with consequences for equine digestion and health.

OBJECTIVES AND METHODS

The present study evaluated the potential of a commercial forage cubes made from alfalfa and mixed meadow grasses to maintain chewing activity when compared with a traditional long and fibre-rich hay. An additional aim was to measure the dust formation during feeding. The experiment was a crossover design with six horses (11 ± 4 years old, mean ± SD), fed with 5 kg (as-fed basis) of their feed (long hay or alfalfa cubes) overnight. Eating and chewing activity was measured using the EquiWatch system with a sensor-based halter.

RESULTS

Data showed that by feeding the same amount of feed overnight, cube feeding led to 24% shorter eating time (on average 67 min less) and 26% fewer total chews compared to the long hay. On an hourly basis, horses also spent more time eating and chewing the long hay compared to the cubes. The cube feeding led to a higher dust concentration of the inhalable fraction (<100 μm), but not of the thoracic (<10 μm) fraction. Nevertheless, average dust concentrations were generally low for both cubes and hay, whereby both were of sound hygienic status.

CONCLUSION AND RECOMMENDATION

Our data suggest that feeding alfalfa-based cubes overnight generated shorter eating time and less chews than the long hay without major differences in the thoracic dust. Therefore, because of the decreased eating time and chews, alfalfa-based cubes should not be fed a sole forage source, especially when it is to be fed without restriction.

The Effects of Bit Wear on Respirable Silica Dust, Noise and Productivity: A Hammer Drill Bench Study

Objectives

Hammer drills are used extensively in commercial construction for drilling into concrete for tasks including rebar installation for structural upgrades and anchor bolt installation. This drilling task can expose workers to respirable silica dust and noise. The aim of this pilot study was to evaluate the effects of bit wear on respirable silica dust, noise, and drilling productivity.

Method

Test bits were worn to three states by drilling consecutive holes to different cumulative drilling depths: 0, 780, and 1560 cm. Each state of bit wear was evaluated by three trials (nine trials total). For each trial, an automated laboratory test bench system drilled 41 holes 1.3 cm diameter, and 10 cm deep into concrete block at a rate of one hole per minute using a commercially available hammer drill and masonry bits. During each trial, dust was continuously captured by two respirable and one inhalable sampling trains and noise was sampled with a noise dosimeter. The room was thoroughly cleaned between trials.

Results

When comparing results for the sharp (0 cm) versus dull bit (1560 cm), the mean respirable silica increased from 0.41 to 0.74 mg m-3 in sampler 1 (P = 0.012) and from 0.41 to 0.89 mg m-3 in sampler 2 (P = 0.024); levels above the NIOSH recommended exposure limit of 0.05 mg m-3. Likewise, mean noise levels increased from 112.8 to 114.4 dBA (P < 0.00001). Drilling productivity declined with increasing wear from 10.16 to 7.76 mm s-1 (P < 0.00001).

Discussion

Increasing bit wear was associated with increasing respirable silica dust and noise and reduced drilling productivity. The levels of dust and noise produced by these experimental conditions would require dust capture, hearing protection, and possibly respiratory protection. The findings support the adoption of a bit replacement program by construction contractors.

Mechanical intervention for reducing dust concentration in traditional rice mills

A huge number of workers are employed in traditional rice mills where they are potentially exposed to dust. In this study a dust collection system was developed to capture the airborne dust in the rice mill. The feeding and sieving section of the mill was identified as major dust creating zone. The dust was captured by creating suitable air stream at feeding and sieving sections of the mill and collected in cyclone dust collector. The air stream was created by blower which was selected on the basis to get minimum air speed of 0.5 m/s in the working zones of workers. It was observed that the developed system is successfully collects the significant amount of dust and able to reduce the dust concentration up to 58%. Further, the respirable dust concentration reduced to below 5 mg/m(3) throughout the mill which is within the recommended limit of dust exposure.