Material strengths of shear-induced platelet aggregation clots and coagulation clots

Arterial occlusion by thrombosis is the immediate cause of some strokes, heart attacks, and peripheral artery disease. Most prior studies assume that coagulation creates the thrombus. However, a contradiction arises as whole blood (WB) clots from coagulation are too weak to stop arterial blood pressures (> 150 mmHg). We measure the material mechanical properties of elasticity and ultimate strength for Shear-Induced Platelet Aggregation (SIPA) type clots, that form under stenotic arterial hemodynamics in comparison with coagulation clots. The ultimate strength of SIPA clots averaged 4.6 ± 1.3 kPa, while WB coagulation clots had a strength of 0.63 ± 0.3 kPa (p < 0.05). The elastic modulus of SIPA clots was 3.8 ± 1.5 kPa at 1 Hz and 0.5 mm displacement, or 2.8 times higher than WB coagulation clots (1.3 ± 1.2 kPa, p < 0.0001). This study shows that the SIPA thrombi, formed quickly under high shear hemodynamics, is seven-fold stronger and three-fold stiffer compared to WB coagulation clots. A force balance calculation shows a SIPA clot has the strength to resist arterial pressure with a short length of less than 2 mm, consistent with coronary pathology.

Novel tubing connectors reduce ECMO circuit thrombosis

BACKGROUND

Thrombosis within extracorporeal membrane oxygenation (ECMO) circuits is a common complication that dominates clinical management of patients receiving mechanical circulatory support. Prior studies have identified that over 80% of circuit thrombosis can be attributed to tubing-connector junctions.

METHODS

A novel connector was designed that reduces local regions of flow stagnation at the tubing-connector junction to eliminate a primary source of ECMO circuit thrombi. To compare clotting between the novel connectors and the traditional connectors, both in vitro loops and an in vivo caprine model of long-term (48 h) ECMO were used to generate tubing-connector junction clots.

RESULTS

In vitro, the traditional connectors uniformly (9/9) formed large thrombi, while novel connectors formed a small thrombus in only one of nine (p < 0.0001). In the long-term goat ECMO circuits, the traditional connectors exhibited more thrombi (p < 0.04), and these thrombi were more likely to protrude into the lumen of the tubing (p < 0.001).

CONCLUSION

Both in vitro and in vivo validation experiments successfully recreated circuit thrombosis and demonstrate that the adoption of novel connectors can reduce the burden of circuit thrombosis.

N-Acetyl Cysteine Prevents Arterial Thrombosis in a Dose-Dependent Manner In Vitro and in Mice

BACKGROUND

Platelet-rich thrombi occlude arteries causing fatal infarcts like heart attacks and strokes. Prevention of thrombi by current antiplatelet agents can cause major bleeding. Instead, we propose using N-acetyl cysteine (NAC) to act against the protein VWF (von Willebrand factor), and not platelets, to prevent arterial thrombi from forming.

METHODS

NAC was assessed for its ability to prevent arterial thrombosis by measuring platelet accumulation rate and occlusion time using a microfluidic model of arterial thrombosis with human blood. Acute clot formation, clot stability, and tail bleeding were measured in vivo with the murine modified Folts model. The effect of NAC in the murine model after 6 hours was also measured to determine any persistent effects of NAC after it has been cleared from the blood.

RESULTS

We demonstrate reduction of thrombi formation following treatment with NAC in vitro and in vivo. Human whole blood treated with 3 or 5 mmol/L NAC showed delayed thrombus formation 2.0× and 3.7× longer than control, respectively (P<0.001). Blood treated with 10 mmol/L NAC did not form an occlusive clot, and no macroscopic platelet aggregation was visible (P<0.001). In vivo, a 400-mg/kg dose of NAC prevented occlusive clots from forming in mice without significantly affecting tail bleeding times. A lower dose of NAC significantly reduced clot stability. Mice given multiple injections showed that NAC has a lasting and cumulative effect on clot stability, even after being cleared from the blood (P<0.001).

CONCLUSIONS

Both preclinical models demonstrate that NAC prevents thrombus formation in a dose-dependent manner without significantly affecting bleeding time. This work highlights a new pathway for preventing arterial thrombosis, different from antiplatelet agents, using an amino acid derivative as an antithrombotic therapeutic.

Don't forget about human factors: Lessons learned from COVID-19 point-of-care testing

During the COVID-19 pandemic, the development of point-of-care (POC) diagnostic testing accelerated in an unparalleled fashion. As a result, there has been an increased need for accurate, robust, and easy-to-use POC testing in a variety of non-traditional settings (i.e., pharmacies, drive-thru sites, schools). While stakeholders often express the desire for POC technologies that are "as simple as digital pregnancy tests," there is little discussion of what this means in regards to device design, development, and assessment. The design of POC technologies and systems should take into account the capabilities and limitations of the users and their environments. Such "human factors" are important tenets that can help technology developers create POC technologies that are effective for end-users in a multitude of settings. Here, we review the core principles of human factors and discuss lessons learned during the evaluation process of SARS-CoV-2 POC testing.

Designing for simplicity: lessons from Mesa Biotech for microfluidic entrepreneurs and early-stage companies

The COVID-19 pandemic has proven the need for point-of-care diagnosis of respiratory diseases and microfluidic technology has risen to the occasion. Mesa Biotech (San Diego, CA) originally developed the Accula platform for the diagnosis of influenza A and B and then extended the platform to SARS-CoV-2. Mesa Biotech has experienced tremendous success, culminating in acquisition by Thermo Fisher for up to $550m USD. The Accula microfluidics platform accomplished the leap from the lab to commercial product through clever design and engineering choices. Through information obtained from interviews with key Mesa Biotech leaders and publicly-available documents, we describe the keys to Mesa's success and how they might inform other lab-on-a-chip companies.

Thrombogenicity of biomaterials depends on hemodynamic shear rate

BACKGROUND

While it is well recognized that different biomaterials induce thrombosis at low shear rates, the effect of high shear rates may be quite different. We hypothesize that the amount of thrombus formation on a given material can be greatly influenced by the local shear rate.

METHODS

We tested this hypothesis with two different whole blood perfusion loop assays to quantify biomaterial thrombogenicity as a function of shear stress. One assay uses obstructive posts (pins) of material positioned centrally in a tube perfused at high shear rate of >5000/s for 24 h. A second assay uses a parallel plate chamber to perfuse low (<150/s), medium (~500/s), and high shear rates over 96 h. We evaluated the thrombogenicity of seven different biomaterials including stainless steel, acrylic, ceramic, Dacron, polytetrafluoroethylene (PTFE), silicone, and polyvinyl chloride (PVC).

RESULTS

For the pin assay, thrombus mass was significantly greater for stainless steel than either zirconia ceramic or acrylic (p < 0.001). Similarly, the parallel plate chamber at high shear showed that steel and PTFE (p < 0.02) occluded the chamber faster than acrylic. In contrast, a low shear parallel plate chamber revealed that stainless steel and PTFE were least thrombogenic, while silicone, Dacron, and other plastics such as acrylic were most thrombogenic. Histology revealed that high shear thrombi had a large proportion of platelets not seen in the low shear fibrin-rich thrombi.

CONCLUSION

This differential thrombogenicity based on shear rate conditions may be important in the selection of biomaterials for blood-contacting devices.

Global Thrombosis Test: Occlusion by Coagulation or SIPA?

The global thrombosis test (GTT) is a point of care device that tests thrombotic and thrombolytic status. The device exposes whole blood flow to a combination of both high and low shear stress past and between ball bearings potentially causing thrombin and fibrin formation. The question arises as to whether thrombosis in the GTT is dominated by coagulation-triggered red clot or high shear-induced white clot. We investigated the nature of the thrombus formed in the GTT, the device efficacy, human factors use, and limitations. The GTT formed clots that were histologically fibrin-rich with trapped red blood cells. The occlusion time (OT) was more consistent with coagulation than high shear white clot and was strongly lengthened by heparin and citrate, two common anticoagulants. The clot was lysed by tissue plasminogen activator (tPA), also consistent with a fibrin-rich red clot. Changing the bead to a collagen-coated surface and eliminating the low shear zone between the beads induced a rapid OT consistent with a platelet-rich thrombus that was relatively resistant to heparin or tPA. The evidence points to the GTT as occluding primarily due to fibrin-rich red clot from coagulation rather than high shear platelet aggregation and occlusion associated with arterial thrombosis.

Negatively charged nanoparticles of multiple materials inhibit shear-induced platelet accumulation

Platelet accumulation by VWF under high shear rates at the site of atherosclerotic plaque rupture leads to myocardial infarction and stroke. Current anti-platelet therapies remain ineffective for a large percentage of the population, while presenting significant risks for bleeding. We explore a novel way to inhibit arterial thrombus formation. Theoretically, a negative charge may influence the tertiary structure of VWF to favor the globular configuration by biophysical means without the use of platelet inactivating drugs. We tested this hypothesis experimentally for charged nanoparticles (CNPs) to inhibit thrombus formation in a microfluidic thrombosis assay (MTA). Several different CNPs demonstrated the ability to retard thrombotic occlusion in the MTA. A preliminary study in mice shows that thrombus stability is weaker with CNP administration and bleeding times are not markedly prolonged. The CNPs tested here show promise as a new class of antithrombotic therapies that act by biophysical means rather than biochemical pathways.

Mechanobiology of shear-induced platelet aggregation leading to occlusive arterial thrombosis: A multiscale in silico analysis

Occlusive thrombosis in arteries causes heart attacks and strokes. The rapid growth of thrombus at elevated shear rates (~10,000 1/s) relies on shear-induced platelet aggregation (SIPA) thought to come about from the entanglement of von Willebrand factor (VWF) molecules. The mechanism for SIPA is not yet understood in terms of cell- and molecule-level dynamics in fast flowing bloodstreams. Towards this end, we develop a multiscale computational model to recreate SIPA in silico, where the suspension dynamics and interactions of individual platelets and VWF multimers are resolved directly. The platelet-VWF interaction via GP1b-A1 bonds is prescribed with intrinsic binding rates theoretically derived and informed by single-molecule measurements. The model is validated against existing microfluidic SIPA experiments, showing good agreement with the in vitro observations in terms of the morphology, traveling distance and capture time of the platelet aggregates. Particularly, the capture of aggregates can occur in a few milliseconds, comparable to the platelet transit time through pathologic arterial stenotic sections and much shorter than the time for shear-induced platelet activation. The multiscale SIPA simulator provides a cross-scale tool for exploring the biophysical mechanisms of SIPA in silico that are difficult to access with single-molecule measurements or micro-/macro-fluidic assays only.

Lysis of arterial thrombi by perfusion of N,N'-Diacetyl-L-cystine (DiNAC)

The search persists for a safe and effective agent to lyse arterial thrombi in the event of acute heart attacks or strokes due to thrombotic occlusion. The culpable thrombi are composed either primarily of platelets and von Willebrand Factor (VWF), or polymerized fibrin, depending on the mechanism of formation. Current thrombolytics were designed to target red fibrin-rich clots, but may be not be efficacious on white VWF-platelet-rich arterial thrombi. We have developed an in vitro system to study the efficacy of known and proposed thrombolytic agents on white clots formed from whole blood in a stenosis with arterial conditions. The agents and adjuncts tested were tPA, ADAMTS-13, abciximab, N-acetyl cysteine, and N,N'-Diacetyl-L-cystine (DiNAC). Most of the agents, including tPA, had little thrombolytic effect on the white clots. In contrast, perfusion of DiNAC lysed thrombi as quickly as 1.5 min, which ranged up to 30 min at lower concentrations, and resulted in an average reduction in surface area of 71 ± 20%. The clot burden was significantly reduced compared to both tPA and a saline control (p<0.0001). We also tested the efficacy of all agents on red fibrinous clots formed in stagnant conditions. DiNAC did not lyse red clots, whereas tPA significantly lysed red clot over 48 h (p<0.01). These results lead to a novel use for DiNAC as a possible thrombolytic agent against acute arterial occlusions that could mitigate the risk of hyper-fibrinolytic bleeding.

Haemodynamic flow conditions at the initiation of high-shear platelet aggregation: a combined in vitro and cellular in silico study

The influence of the flow environment on platelet aggregation is not fully understood in high-shear thrombosis. The objective of this study is to investigate the role of a high shear rate in initial platelet aggregation. The haemodynamic conditions in a microfluidic device are studied using cell-based blood flow simulations. The results are compared with in vitro platelet aggregation experiments performed with porcine whole blood (WB) and platelet-rich-plasma (PRP). We studied whether the cell-depleted layer in combination with high shear and high platelet flux can account for the distribution of platelet aggregates. High platelet fluxes at the wall were found in silico. In WB, the platelet flux was about twice as high as in PRP. Additionally, initial platelet aggregation and occlusion were observed in vitro in the stenotic region. In PRP, the position of the occlusive thrombus was located more downstream than in WB. Furthermore, the shear rates and stresses in cell-based and continuum simulations were studied. We found that a continuum simulation is a good approximation for PRP. For WB, it cannot predict the correct values near the wall.

Endograft exclusion of the false lumen restores local hemodynamics in a model of type B aortic dissection

OBJECTIVE

Endovascular intervention in uncomplicated type B dissection has not been shown conclusively to confer benefit on patients. The hemodynamic effect of primary entry tear coverage is not known. Endovascular stent grafts were deployed in a model of aortic dissection with multiple fenestrations to study these effects. It is hypothesized that endograft deployment will lead to restoration of parabolic true lumen flow as well as elimination of false lumen flow and transluminal jets and vortices locally while maintaining distal false lumen canalization.

METHODS

Thoracic stent grafts were placed in silicone models of aortic dissection with a compliant and mobile intimal flap and installed in a flow loop. Pulsatile fluid flow was established with a custom positive displacement pump, and the models were imaged by four-dimensional flow magnetic resonance imaging. Full flow fields were acquired in the models, and velocities were extracted to calculate flow rates, reverse flow indices, and oscillatory shear index, the last two of which are measures of stagnant and disturbed flows.

RESULTS

Complete obliteration of the false lumen was achieved in grafted aorta, with normal parabolic flow profiles in the true lumen (maximal velocity, 30.4 ± 8.4 cm/s). A blind false lumen pouch was created distal to this with low-velocity (5.8 ± 2.7 cm/s) and highly reversed (27.9% ± 13.9% reverse flow index) flows. In distal free false lumen segments, flows were comparable to ungrafted conditions with maximal velocities on the order of 7.0 ± 2.1 cm/s. Visualization studies revealed forward flow in these regions with left-handed vortices from true to false lumen. Shear calculations in free false lumen regions demonstrated reduced oscillatory shear index.

CONCLUSIONS

Per the initial hypothesis, endovascular grafting improved true lumen hemodynamics in the grafted region. Just distally, a prothrombotic flow regimen was noted in the false lumen, yet free false lumen distal to this remained canalized. Clinically, this suggests a need for advancing endovascular intervention beyond sole entry tear coverage to prevent further false lumen canalization through uncovered fenestrations.

Clot Permeability, Agonist Transport, and Platelet Binding Kinetics in Arterial Thrombosis

The formation of wall-adherent platelet aggregates is a critical process in arterial thrombosis. A growing aggregate experiences frictional drag forces exerted on it by fluid moving over or through the aggregate. The magnitude of these forces is strongly influenced by the permeability of the developing aggregate; the permeability depends on the aggregate's porosity. Aggregation is mediated by formation of ensembles of molecular bonds; each bond involves a plasma protein bridging the gap between specific receptors on the surfaces of two different platelets. The ability of the bonds existing at any time to sustain the drag forces on the aggregate determines whether it remains intact or sheds individual platelets or larger fragments (emboli). We investigate platelet aggregation in coronary-sized arteries using both computational simulations and in vitro experiments. The computational model tracks the formation and breaking of bonds between platelets and treats the thrombus as an evolving porous, viscoelastic material, which moves differently from the background fluid. This relative motion generates drag forces which the fluid and thrombus exert on one another. These forces are computed from a permeability-porosity relation parameterized from experimental measurements. Basing this relation on measurements from occlusive thrombi formed in our flow chamber experiments, along with other physiological parameter values, the model produced stable dense thrombi on a similar timescale to the experiments. When we parameterized the permeability-porosity relation using lower permeabilities reported by others, bond formation was insufficient to balance drag forces on an early thrombus and keep it intact. Under high shear flow, soluble agonist released by platelets was limited to the thrombus and a boundary layer downstream, thus restricting thrombus growth into the vessel lumen. Adding to the model binding and activation of unactivated platelets through von Willebrand-factor-mediated processes allowed greater growth and made agonist-induced activation more effective.

Occlusive thrombosis in arteries

Thrombus formation in major arteries is life threatening. In this review article, we discuss how an arterial thrombus can form under pathologically high shear stresses, with bonding rates estimated to be the fastest Kon values in biochemistry. During occlusive thrombosis in arteries, the growth rate of the thrombus explodes to capture a billion platelets in about 10 min. Close to 100% of all platelets passing the thrombus are captured by long von Willebrand factor (vWF) strands that quickly form tethered nets. The nets grow in patches where shear stress is high, and the local concentration of vWF is elevated due to α-granule release by previously captured platelets. This rapidly formed thrombus has few red blood cells and so has a white appearance and is much stronger and more porous than clots formed through coagulation. Understanding and modeling the biophysics of this event can predict totally new approaches to prevent and treat heart attacks and strokes.

Shear-induced platelet aggregation: 3D-grayscale microfluidics for repeatable and localized occlusive thrombosis

Atherothrombosis leads to complications of myocardial infarction and stroke as a result of shear-induced platelet aggregation (SIPA). Clinicians and researchers may benefit from diagnostic and benchtop microfluidic assays that assess the thrombotic activity of an individual. Currently, there are several different proposed point-of-care diagnostics and microfluidic thrombosis assays with different design parameters and end points. The microfluidic geometry, surface coatings, and anticoagulation may strongly influence the precision of these assays. Variability in selected end points also persists, leading to ambiguous results. This study aims to assess the effects of three physiologically relevant extrinsic design factors on the variability of a single end point to provide a quantified rationale for design parameter and end-point standardization. Using a design of experiments approach, we show that the methods of channel fabrication and collagen surface coating significantly impact the variability of occlusion time from porcine whole blood, while anticoagulant selection between heparin and citrate did not significantly impact the variability. No factor was determined to significantly impact the mean occlusion time within the assay. Occlusive thrombus was found to consistently form in the first third (333 μm) of the high shear zone and not in the shear gradient regions. The selection of these factors in the design of point-of-care diagnostics and experimental SIPA assays may lead to increased precision and specificity in high shear thrombosis studies.

Intermediate fenestrations reduce flow reversal in a silicone model of Stanford Type B aortic dissection

Pulsatile, three-dimensional hemodynamic forces influence thrombosis, and may dictate progression of aortic dissection. Intimal flap fenestration and blood pressure are clinically relevant variables in this pathology, yet their effects on dissection hemodynamics are poorly understood. The goal of this study was to characterize these effects on flow in dissection models to better guide interventions to prevent aneurysm formation and false lumen flow. Silicone models of aortic dissection with mobile intimal flap were fabricated based on patient images and installed in a flow loop with pulsatile flow. Flow fields were acquired via 4-dimensional flow MRI, allowing for quantification and visualization of relevant fluid mechanics. Pulsatile vortices and jet-like structures were observed at fenestrations immediately past the proximal entry tear. False lumen flow reversal was significantly reduced with the addition of fenestrations, from 19.2 ± 3.3% in two-tear dissections to 4.67 ± 1.5% and 4.87 ± 1.7% with each subsequent fenestration. In contrast, increasing pressure did not cause appreciable differences in flow rates, flow reversal, and vortex formation. Increasing the number of intermediate tears decreased flow reversal as compared to two-tear dissection, which may prevent false lumen thrombosis, promoting persistent false lumen flow. Vortices were noted to result from transluminal fluid motion at distal tear sites, which may lead to degeneration of the opposing wall. Increasing pressure did not affect measured flow patterns, but may contribute to stress concentrations in the aortic wall. The functional and anatomic assessment of disease with 4D MRI may aid in stratifying patient risk in this population.

Who Create Jobs? Venture Capital, Research Grants, and Regional Employment in the U.S

We build on the exploratory and exploitative learning literature that suggests that venture capital and governmental research grants may impact regional employment in a different manner. Using a regional employment dataset in the U.S. medical device sector, our analysis reveals that research grants contribute to create a greater level of regional employment compared with venture capital funding. Furthermore, the positive effects of both funding sources are more salient when intellectual capital is abundant in the region. More specifically, the interaction effect of research grants and intellectual capital is gradually increased in the long term and eventually becomes greater than that of venture capital and intellectual capital, which is relatively constant. These findings highlight the heterogeneous motivations and consequences of two funding sources that should be considered in the future resource allocation policy accordingly.

Inhibition of high shear arterial thrombosis by charged nanoparticles

Platelet accumulation under high shear rates at the site of atherosclerotic plaque rupture leads to myocardial infarction and stroke. Current antiplatelet therapies remain ineffective within a large percentage of the population, while presenting significant risks for bleeding. We explore a novel way to inhibit arterial thrombus formation by biophysical means without the use of platelet inactivating drugs. Our computational multi-scale dynamics model has predicted that charged particles of a specific size may entangle von Willebrand Factor (vWF) polymers and reduce the amount of elongation at high shear rates. We tested this hypothesis experimentally for negatively charged nanoparticles (CNP) to inhibit arterial thrombus formation. CNP of a particular size and charge inhibited thrombus formation, with a 10-fold peak inhibition over control conditions of thrombotic occlusion. Particles of differing material composition, size, and charge had little effect as predicted by computational studies. Surprisingly, the dose response curve was not sigmoidal, but exhibited a peak at 1.5 CNP:vWF proteins, which was not predicted by the model. This study describes a new antithrombotic agent that may have a different mechanism of action than current pharmaceutical therapies.

Differential effects of public and private funding in the medical device industry

INTRODUCTION

Funding for scientific advancement comes from two dominant sources: public funds used to generate knowledge, and private sector funds in the pursuit of commercial products. It is unclear how to compare the outputs of these two financial mechanisms because both sectors are motivated by common goods but are also governed by divergent forces. Employment within a geographic region may be a metric of mutual value that can be applied equally to assess the societal impacts of two financing sources. Areas covered: The authors focused on the medical device industry, which is a robust sector of growth for the U.S. economy. The U.S. NIH and venture capital community are representatives of public and private capital, respectively. Using a longitudinal employment dataset of 247 distinct locations, the authors found that NIH funding tends to create more jobs directly compared to venture capital funding. Moreover, the indirect effect of governmental funding is initially smaller than that of venture capital funding for the first two years, but eventually surpasses that of venture capital funding. Expert commentary: These findings imply that policy decisions regarding financial allocations in the medical device industry should consider the appropriate typology of financial capital and its consequences.

Hemodynamic studies of platelet thrombosis using microfluidics

Platelets contribute to thrombus formation in a variety of ways. Platelet adhesion, activation, and thrombus growth depend greatly on the type of hemodynamic environment surrounding an inciting event. Microfluidic systems may be used to explore these relationships. In this review, we describe some important considerations required in the design of a microfluidic system and identify some limitations that may require use of a macroscale system.

Flow and wall shear stress characterization after endovascular aneurysm repair and endovascular aneurysm sealing in an infrarenal aneurysm model

BACKGROUND

Endovascular aneurysm repair (EVAR) with a modular endograft has become the preferred treatment for abdominal aortic aneurysms. A novel concept is endovascular aneurysm sealing (EVAS), consisting of dual endoframes surrounded by polymer-filled endobags. This dual-lumen configuration is different from a bifurcation with a tapered trajectory of the flow lumen into the two limbs and may induce unfavorable flow conditions. These include low and oscillatory wall shear stress (WSS), linked to atherosclerosis, and high shear rates that may result in thrombosis. An in vitro study was performed to assess the impact of EVAR and EVAS on flow patterns and WSS.

METHODS

Four abdominal aortic aneurysm phantoms were constructed, including three stented models, to study the influence of the flow divider on flow (Endurant [Medtronic, Minneapolis, Minn], AFX [Endologix, Irvine, Calif], and Nellix [Endologix]). Experimental models were tested under physiologic resting conditions, and flow was visualized with laser particle imaging velocimetry, quantified by shear rate, WSS, and oscillatory shear index (OSI) in the suprarenal aorta, renal artery (RA), and common iliac artery.

RESULTS

WSS and OSI were comparable for all models in the suprarenal aorta. The RA flow profile in the EVAR models was comparable to the control, but a region of lower WSS was observed on the caudal wall compared with the control. The EVAS model showed a stronger jet flow with a higher shear rate in some regions compared with the other models. Small regions of low WSS and high OSI were found near the distal end of all stents in the common iliac artery compared with the control. Maximum shear rates in each region of interest were well below the pathologic threshold for acute thrombosis.

CONCLUSIONS

The different stent designs do not influence suprarenal flow. Lower WSS is observed in the caudal wall of the RA after EVAR and a higher shear rate after EVAS. All stented models have a small region of low WSS and high OSI near the distal outflow of the stents.

Choice of a hemodynamic model for occlusive thrombosis in arteries

Intravascular thrombosis can lead to heart attacks and strokes that together are the leading causes of death in the US (Kochanek, K.D., Murphy, S.L., Xu, J.Q., 2014). The ability to identify the offending biofluid mechanical conditions and predict the timescale of thrombotic occlusion in vessels and devices may improve patient outcomes. A computational model was developed to describe the growth of thrombus based on the local hemodynamic shear rate. The model predicts thrombus deposition based on initial geometric and fluid mechanical conditions, which are updated throughout the simulation to reflect the changing lumen dimensions. Thrombus growth and occlusion from whole blood was measured in in vitro experiments using stenotic glass capillary tubes, a PDMS microfluidic channel, and a PTFE stenotic aorto-iliac graft. Comparison of the predicted occlusion times to experimental results shows excellent agreement. The results indicate that local shear rate plays a critical role in acute thrombosis, and that hemodynamic characterization may have clinical utility.

Ability of device to collect bacteria from cough aerosols generated by adults with cystic fibrosis

Background: Identifying lung pathogens and acute spikes in lung counts remain a challenge in the treatment of patients with cystic fibrosis (CF). Bacteria from the deep lung may be sampled from aerosols produced during coughing. Methods: A new device was used to collect and measure bacteria levels from cough aerosols of patients with CF. Sputum and oral specimens were also collected and measured for comparison. Pseudomonas aeruginosa, Staphylococcus aureus, Klebsiella pneumoniae, and Streptococcus mitis were detected in specimens using Real-Time Polymerase Chain Reaction (RT-PCR) molecular assays. Results: Twenty adult patients with CF and 10 healthy controls participated. CF related bacteria (CFRB) were detected in 13/20 (65%) cough specimens versus 15/15 (100%) sputum specimens. Commensal S. mitis was present in 0/17 (0%, p=0.0002) cough specimens and 13/14 (93%) sputum samples. In normal controls, no bacteria were collected in cough specimens but 4/10 (40%) oral specimens were positive for CFRB. Conclusions: Non-invasive cough aerosol collection may detect lower respiratory pathogens in CF patients, with similar specificity and sensitivity to rates detected by BAL, without contamination by oral CFRB or commensal bacteria.

Abstract 102: Number of Reentry Tears Influences Flap Motion and Flow Reversal in an in vitro Model of Type B Aortic Dissection

Objectives: Aortic remodeling after dissection is poorly understood. Thus, optimal patient-specific recommendations for treatment are lacking. An in vitro aortic model of Type B dissection was used to interrogate local aortic hemodynamic parameters implicated in thrombosis and aneurysm formation. We hypothesize that dissections with multiple reentry tears will exhibit decreased flap motion, and, as a result, reduce flow reversal.

Methods: Anatomic models of aortic dissection with fidelity to patient CT images were fabricated out of silicone. Models with primary entry and single fenestration (Figure 1A), two fenestrations (Figure 1B), and three fenestrations (Figure 1C) were installed in a flow loop. Physiologic flow was established at a cardiac index of 4 L/min. Flow velocities were acquired using phase contrast magnetic resonance (PCMR) imaging. Flow rates and flap motion were quantified using custom made software.

Results: Relative true lumen area (RTLA) varied along the dissection (entry: 55% +/- 3, middle: 34% +/-7, exit: 91%+/-3, p<0.00001 pair-wise for 2-tear model). At mid-dissection, RTLA was lower in dissections with fewer tears (p<0.01). Total flow was nearly identical in all cases, while true and false lumen flow rates differed significantly across tear configurations and along the dissection (p<0.01). Secondary tears allowed for flow communication within the dissected portion of the aortic model. Flow reversal was seen in the false lumen at the mid-dissection plane in the absence of secondary tears (Figure 1D). However, as secondary tears were added, the flow reversal in the false lumen decreased, with concomitant flow reversal in the true lumen (Figure 1E,F).

Conclusions: Anatomic characteristics of dissection, such as number of tears, affect blood flow and motion of the dissection flap, as shown quantitatively. This compliant aorta model illustrates alterations in flow reversal in both true and false lumina that may lead to aneurysmal degeneration.

Effects of shear rate, confinement, and particle parameters on margination in blood flow

The effects of flow and particle properties on margination of particles in red blood cell (RBC) suspensions is investigated using direct numerical simulation (DNS) of cellar blood flow. We focus on margination of particles in the flow of moderately dense suspensions of RBCs. We hypothesize that margination rate in nondilute suspensions is mainly driven by the RBC-enhanced diffusion of marginating particles in the RBC-filled region. We derive a scaling law for margination length in a straight channel. Margination length increases cubically with channel height and is independent of shear rate. We verify this scaling law for margination length by DNS of flowing RBCs and marginating particles. We also show that rigidity and size both lead to particle margination with rigidity having a more significant effect compared to size within the range of parameters in this study.

Poly(vinyl alcohol) hydrogel coatings with tunable surface exposure of hydroxyapatite

Insufficient bone anchoring is a major limitation of artificial substitutes for connective osteoarticular tissues. The use of coatings containing osseoconductive ceramic particles is one of the actively explored strategies to improve osseointegration and strengthen the bone-implant interface for general tissue engineering. Our hypothesis is that hydroxyapatite (HA) particles can be coated robustly on specific assemblies of PVA hydrogel fibers for the potential anchoring of ligament replacements. A simple dip-coating method is described to produce composite coatings made of microscopic hydroxyapatite (HA) particles dispersed in a poly(vinyl alcohol) (PVA) matrix. The materials are compatible with the requirements for implant Good Manufacturing Practices. They are applied to coat bundles of PVA hydrogel fibers used for the development of ligament implants. By means of optical and electronic microscopy, we show that the coating thickness and surface state can be adjusted by varying the composition of the dipping solution. Quantitative analysis based on backscattered electron microscopy show that the exposure of HA at the coating surface can be tuned from 0 to over 55% by decreasing the weight ratio of PVA over HA from 0.4 to 0.1. Abrasion experiments simulating bone-implant contact illustrate how the coating cohesion and wear resistance increase by increasing the content of PVA relative to HA. Using pullout experiments, we find that these coatings adhere well to the fiber bundles and detach by propagation of a crack inside the coating. These results provide a guide to select coated implants for anchoring artificial ligaments.

Development and testing of a silicone in vitro model of descending aortic dissection

BACKGROUND

Stanford type B dissection of the descending aorta is a potentially fatal condition that is poorly understood. Limited scientific understanding of the role of current interventional techniques, as well as heterogeneity in the condition, contributes to lack of consensus as to the most effective treatment strategy. This study introduces an anatomically accurate model for investigating aortic dissection in a laboratory setting.

MATERIALS AND METHODS

A silicone model was fabricated and filled with fluid to mimic human blood. Flow was established, and the model was scanned using a four-dimensional flow magnetic resonance imaging protocol. On analysis, luminal flow rates were quantified by multiplying local velocity by included area.

RESULTS

The upstream total flow was compared with the sum of the flow in the true and false lumens. The two values were within the margin of error. Furthermore, flow rates matched with the relative areas of each compartment.

CONCLUSIONS

These results validate our model as a novel and unique system that mimics a type B aortic dissection and will allow for more sophisticated analysis of dissection physiology in future studies.

Abstract 136: Stent-Supported Prosthetic Vein Valve

Background: In chronic venous insufficiency, incompetent valves prevent effective blood return and lead to varicose veins, lower extremity edema, and stasis ulcers. Several surgical interventions have been described, including valve transplantation, but these extensive procedures are only moderately effective and require inpatient hospitalization. Valve replacement technology continues to evolve and this project reports the design, verification, and pre-clinical validation of a new prosthetic vein valve.

Methods: A venous valve has been constructed from a hydrogel and bare-metal stent that has the natural open configuration. Design verification was performed by testing competency, flow resistance, mechanical fatigue, and in vitro thrombogenicity. CFD analysis was used to quantify the shear rates within the valve that may induce platelet aggregation. A large animal study has been initiated to evaluate in vivo performance by open implantation into ovine jugular vein followed by periodic venography. Animals were not heparinized during implantation but were maintained on aspirin in the post-operative period.

Results: The valve presents little resistance, allowed physiologic flow rates 400-600mL/min, and tolerated up to 2800mL/min. Preclinical testing shows the valve is also competent under physiologic pressures of 35-50mmHg and computed shear stress rates were maintained below 4000s-1. Fatigue testing up to 500,000 cycles did not cause valve damage. Antegrade venography confirmed patency of the venous valve continuing beyond 4 weeks in sheep. Placement in sheep would be much better with catheter placement using endosurgical techniques.

Conclusion: This new prosthetic valve design meets physiologic and hemodynamic criteria for clinical use and patency has been maintained at the 4 week time point. Early occlusions may be prevented with operative anticoagulation

Platelet transport rates and binding kinetics at high shear over a thrombus

Thrombus formation over a ruptured atherosclerotic plaque cap can occlude an artery with fatal consequences. We describe a computational model of platelet transport and binding to interpret rate-limiting steps seen in experimental thrombus formation over a collagen-coated stenosis. The model is used to compute shear rates in stenoses with growing boundaries. In the model, moving erythrocytes influence platelet transport based on shear-dependent enhanced diffusivity and a nonuniform platelet distribution. Adhesion is modeled as platelet-platelet binding kinetics. The results indicate that observed thrombus growth rates are limited by platelet transport to the wall for shear rates up to 6000 s(-1). Above 7000 s(-1), the thrombus growth rate is likely limited by binding kinetics (10(-4) m/s). Thrombus growth computed from these rate-limiting steps match the thrombus location and occlusion times for experimental conditions if a lag time for platelet activation is included. Using fitted parameters, the model is then used to predict thrombus size and shape at a higher Reynolds number flow consistent with coronary artery disease.

Microfluidic thrombosis under multiple shear rates and antiplatelet therapy doses

The mainstay of treatment for thrombosis, the formation of occlusive platelet aggregates that often lead to heart attack and stroke, is antiplatelet therapy. Antiplatelet therapy dosing and resistance are poorly understood, leading to potential incorrect and ineffective dosing. Shear rate is also suspected to play a major role in thrombosis, but instrumentation to measure its influence has been limited by flow conditions, agonist use, and non-systematic and/or non-quantitative studies. In this work we measured occlusion times and thrombus detachment for a range of initial shear rates (500, 1500, 4000, and 10000 s(-1)) and therapy concentrations (0-2.4 µM for eptifibatide, 0-2 mM for acetyl-salicylic acid (ASA), 3.5-40 Units/L for heparin) using a microfluidic device. We also measured complete blood counts (CBC) and platelet activity using whole blood impedance aggregometry. Effects of shear rate and dose were analyzed using general linear models, logistic regressions, and Cox proportional hazards models. Shear rates have significant effects on thrombosis/dose-response curves for all tested therapies. ASA has little effect on high shear occlusion times, even at very high doses (up to 20 times the recommended dose). Under ASA therapy, thrombi formed at high shear rates were 4 times more prone to detachment compared to those formed under control conditions. Eptifibatide reduced occlusion when controlling for shear rate and its efficacy increased with dose concentration. In contrast, the hazard of occlusion from ASA was several orders of magnitude higher than that of eptifibatide. Our results show similar dose efficacy to our low shear measurements using whole blood aggregometry. This quantitative and statistically validated study of the effects of a wide range of shear rate and antiplatelet therapy doses on occlusive thrombosis contributes to more accurate understanding of thrombosis and to models for optimizing patient treatment.

A passive quantitative measurement of airway resistance using depth data

The Respiratory Syncytial Virus (RSV) is the most common cause of serious lower respiratory tract infections in infants and young children. RSV often causes increased airway resistance, clinically detected as wheezing by chest auscultation. In this disease, expiratory flows are significantly reduced due to the high resistance in patient's airway passages. A quantitative method for measuring resistance can have a great benefit to diagnosis and management of children with RSV infections as well as with other lung diseases. Airway resistance is defined as the lung pressure divided by the airflow. In this paper, we propose a method to quantify resistance through a simple, non-contact measurement of chest volume that can act as a surrogate measure of the lung pressure and volumetric airflow. We used depth data collected by a Microsoft Kinect camera for the measurement of the lung volume over time. In our experimentation, breathing through a number of plastic straws induced different airway resistances. For a standard spirometry test, our volume/flow estimation using Kinect showed strong correlation with the flow data collected by a commercially-available spirometer (five subjects, each performing 20 breathing trials, correlation coefficient = 0.88, with 95% confidence interval). As the number of straws decreased, emulating a higher airway obstruction, our algorithm was sufficient to distinguish between several levels of airway resistance.

A low-volume, single pass in-vitro system of high shear thrombosis in a stenosis

INTRODUCTION

Arterial thrombosis leading to heart attack and stroke requires the rapid accumulation of millions of platelets under pathologically high shear. Previous in vitro systems studying platelets typically use endpoints that emphasize platelet-surface effects rather than large-scale platelet-platelet accumulation that precedes occlusion. Further, most platelet tests do not recreate shear rates present during arterial occlusion. We present an alternative flow system to study large thrombus formation under pathologic shear conditions in an anatomic stenosis with reasonable volumes of human blood.

MATERIALS AND METHODS

An in-vitro system using a syringe pump was created to subject low volume (<30 mLs), whole blood samples to very high shear rates (>3,500 s(-1)) through a stenosis. Thrombus was quantified using an optical microscope from initial deposition to large scale accumulation. Images were taken using a high definition camera in real time.

RESULTS AND CONCLUSIONS

Occlusive thrombus blocks the collagen-coated lumen with millions of platelets using human whole, heparinized blood. Rapid Platelet Accumulation rates in human blood are 4.5±2.4 μm(3)/μm(2)/min (n=21). There is an initial lag time of 7.4±3.8 min (n=21) before the onset of large scale thrombosis. The rates of platelet accumulation in vitro are consistent with the clinical timescale of coronary or carotid artery occlusion. Porcine blood has a faster accumulation rate of 9.6±6.1 μm(3)/μm(2)/min (n=7, p<0.05) and a shorter lag time of 2.7±0.5 min (n=7, p<0.05). The long lag time for large thrombus formation suggests that some in-vitro assays will miss the main mechanism creating thrombotic occlusion.

Design Considerations for a Prosthetic Anterior Cruciate Ligament

Anterior cruciate ligament (ACL) tearing is a common knee injury often requiring reconstruction with an autograft or an allograft. A prosthetic ligament replacement with off-the-shelf availability could potentially provide significant advantages over the current options for both patients and surgeons. Limitations of previous prosthetics include lack of biocompatibility and susceptibility to fatigue, creep, and failure of bony incorporation. This paper describes design considerations and possible improvements for the next generation prosthetic ACL. Design controls, as mandated by the FDA, are a systematic set of practices within the design and development process used to ensure that a new medical device meets the needs of the intended users. The specified requirements, called the design inputs, for a prosthetic ACL are discussed pertaining to material and structural properties, resistance to creep and fatigue, ability to support secure initial fixation, biocompatibility, and long-term osseointegration. Design innovations to satisfy the design inputs are discussed with regards to material selection, textile pattern, bone tunnel features, and short term fixation. A risk analysis is presented along with descriptions of proposed testing. Design control methodology and tissue engineering may be used to develop a next generation prosthetic ligament, solving multiple problems, simultaneously, on a holistic level, providing major improvements over earlier devices and current treatment options.

Determination of critical parameters in platelet margination

An investigation of margination dependence on hematocrit, platelet shape, and viscosity ratio of plasma to cytoplasm is presented. Whole blood is modeled as a suspension of deformable red blood cells (RBCs) and rigid platelets in a viscous liquid. The fluid phase is simulated using the lattice-Boltzmann method, the RBC membranes are modeled with a coarse-grained spectrin-link method, and the dynamics of rigid particles are updated using Newton's equations of motion for axisymmetric shapes. The results emphasize that an increase in hematocrit increases the rate of margination. The viscosity ratio between the interior cytoplasm and suspending fluid can considerably alter the rate of margination. The aspect ratio of surrogate platelet particles influences the rate of margination as well. Spherical particles tend to migrate more quickly than disks. Highly viscous or rigid RBCs slow down margination.

Microfluidic system for simultaneous optical measurement of platelet aggregation at multiple shear rates in whole blood

Thrombosis is the pathological formation of platelet aggregates which occlude blood flow causing stroke and heart attack-the leading causes of death in developed nations. Instrumentation for diagnosing and exploring treatments for pathological platelet aggregation thus has the potential for major clinical impact. Most current thrombosis methods focus on single flow conditions, non-occlusive platelet adhesion, or low shear rates and so are limited in their application to comparative studies involving multiple, pathological test conditions (e.g., shear rate, stenotic geometries that mimic arteries, and rapid platelet accumulation to occlusion). The field could benefit from a low volume, high throughput, short analysis time, and low cost system while minimizing sample handling. We report on the design, fabrication, testing, and application of a microfluidic device and associated optical system for simultaneous measurement of platelet aggregation at multiple initial shear rates within four stenotic channels in label-free whole blood. Following computational design, requisite shear rates were achieved in the device by micro- surface milling a mold and subsequent PDMS casting. We applied the microfluidic system to measure platelet aggregation in whole porcine blood for shear rates spanning physiological to pathological flow conditions (500-13000 s(-1)). Real-time, non-contact, label-free, microscope-free measurements of platelet aggregation were acquired using an optical system comprising a 650 nm diode laser and a linear CCD. We observed fully occlusive platelet aggregation in less than 20 min above a threshold initial shear rate of 4000 s(-1), and no occlusive platelet aggregation below 1500 s(-1) (N = 86 trials). Accumulation of thrombus was consistent between laser intensity, light microscopy, histology, and mass flow rate measurements. The amount of blood volumes producing occlusion were dependent on shear rate. Times to occlusion were not found to be dependent on shear rate above the threshold level of 4000 s(-1). This microfluidic system enables measurement of the entire process of occlusive platelet thrombosis in whole, unlabeled blood, in vitro, at multiple shear rates. Such a system may be useful as a point-of-care diagnostic tool for studying anti-platelet therapies in individual blood samples from high-risk patients.

Design and fabrication of a mechanically matched vascular graft

The study provides a pathway to design a mechanics-matching vascular graft for an end-to-end anastomosis to a host artery. For functional equivalence, we submit that the graft and a host artery should have equal inner deformed diameters, equal pressure-radius module, and experience equal axial forces when subjected to mean arterial pressure. These criteria for mechanical equivalence are valid for a large class of materials that can be considered as elastic incompressible and orthotropic solids. As an example, specific known artery properties were used to design or select a graft made from a new synthetic biomaterial to demonstrate that reliable and robust technology for graft fabrication is possible.

Pump Design for a Portable Renal Replacement System

This work proposes a small, light, valveless pump design for a portable renal replacement system. By analyzing the working principle of the pump and exploring the design space using an analytical pump model, we developed a novel design for a cam-driven finger pump. Several cams sequentially compress fingers, which compress flexible tubes; thus eliminating valves. Changing the speed of the motor or size of the tube controls the flow rate. In vitro experiments conducted with whole blood using the pump measured Creatinine levels over time, and the results verify the design for the portable renal replacement system. The proposed pump design is smaller than 153 cm3 and consumes less than 1 W while providing a flow rate of more than 100 ml/min for both blood and dialysate flows. The smallest pump of a portable renal replacement system in the literature uses check valves, which considerably increase the overall manufacturing cost and possibility of blood clotting. Compared to that pump, the proposed pump design achieved reduction in size by 52% and savings in energy consumption by 89% with the removal of valves. This simple and reliable design substantially reduces the size requirements of a portable renal replacement system.

Augmentation of bone tunnel healing in anterior cruciate ligament grafts: application of calcium phosphates and other materials

Bone tunnel healing is an important consideration after anterior cruciate ligament (ACL) replacement surgery. Recently, a variety of materials have been proposed for improving this healing process, including autologous bone tissue, cells, artificial proteins, and calcium salts. Amongst these materials are calcium phosphates (CaPs), which are known for their biocompatibility and are widely commercially available. As with the majority of the materials investigated, CaPs have been shown to advance the healing of bone tunnel tissue in animal studies. Mechanical testing shows fixation strengths to be improved, particularly by the application of CaP-based cement in the bone tunnel. Significantly, CaP-based cements have been shown to produce improvements comparable to those induced by potentially more complex treatments such as biologics (including fibronectin and chitin) and cultured cells. Further investigation of CaP-based treatment in the bone tunnels during ACL replacement is therefore warranted in order to establish what improvements in healing and resulting clinical benefits may be achieved through its application.

PneumoniaCheck: A Device for Sampling Lower Airway Aerosols

The pathogens causing pneumonia are difficult to identify because a high quality specimen from the lower lung is difficult to obtain. A new specimen collection device is designed to collect aerosol specimens selectively from the lower lung generated during deep coughing. The PneumoniaCheck device utilizes a separation reservoir and Venturi valve to segregate contents from the upper and lower airways. The device also includes several specially designed features to exclude oral contaminants from the sample and a filter to collect the aerosolized pathogens. Verification testing of PneumoniaCheck demonstrates effective separation of upper airway gas from the lower airway gas (p<0.0001) and exclusion of both liquid and viscous oral material (p<0.0001) from the collection chamber. The filters can collect 99.9997% of virus and bacteria sized particles from the sampled lower lung aerosols. The selective collection of specimens from the lower airway may aid in the diagnosis of specific pathogens causing pneumonia.